[2/2] ARM: dts: rockchip: add Netxeon R89 board
diff mbox

Message ID 8379968.L7YrCqSUHX@phil
State New
Headers show

Commit Message

Heiko Stuebner May 26, 2015, 7:50 p.m. UTC
This board is used in some TV-boxes like for example the Beelink R89 or
Tronsmart R28.

The board itself follows the reference design for the most part. But
there are no schematics available it seems, so some things should be
taken with a grain of salt.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
 Documentation/devicetree/bindings/arm/rockchip.txt |   4 +
 arch/arm/boot/dts/Makefile                         |   3 +-
 arch/arm/boot/dts/rk3288-r89.dts                   | 412 +++++++++++++++++++++
 3 files changed, 418 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/rk3288-r89.dts

Patch
diff mbox

diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 60d4a1e..b30bed1 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -26,3 +26,7 @@  Rockchip platforms device tree bindings
 - ChipSPARK PopMetal-RK3288 board:
     Required root node properties:
       - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
+
+- Netxeon R89 board:
+    Required root node properties:
+      - compatible = "netxeon,r89", "rockchip,rk3288";
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 86217db..25a19a4 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -464,7 +464,8 @@  dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3288-evb-act8846.dtb \
 	rk3288-evb-rk808.dtb \
 	rk3288-firefly-beta.dtb \
-	rk3288-firefly.dtb
+	rk3288-firefly.dtb \
+	rk3288-r89.dtb
 dtb-$(CONFIG_ARCH_S3C24XX) += \
 	s3c2416-smdk2416.dtb
 dtb-$(CONFIG_ARCH_S3C64XX) += \
diff --git a/arch/arm/boot/dts/rk3288-r89.dts b/arch/arm/boot/dts/rk3288-r89.dts
new file mode 100644
index 0000000..b1d9ca6
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-r89.dts
@@ -0,0 +1,412 @@ 
+/*
+ * Copyright (c) 2015 Heiko Stuebner <heiko@sntech.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "rk3288.dtsi"
+
+/ {
+	compatible = "netxeon,r89", "rockchip,rk3288";
+
+	memory {
+		reg = <0x0 0x80000000>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+		#clock-cells = <0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn>;
+
+		button@0 {
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			linux,code = <116>;
+			label = "GPIO Key Power";
+			linux,input-type = <1>;
+			gpio-key,wakeup = <1>;
+			debounce-interval = <100>;
+		};
+	};
+
+	vcc_host: vcc-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host_vbus_drv>;
+		regulator-name = "vcc_host";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_otg: vcc-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&otg_vbus_drv>;
+		regulator-name = "vcc_otg";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_sdmmc: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "sdmmc-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+		startup-delay-us = <100000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_sys: sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "sys-supply";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&gmac {
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: pmic@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "VDD_CPU";
+		regulator-enable-ramp-delay = <300>;
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-ramp-delay = <8000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vdd_gpu: pmic@41 {
+		compatible = "silergy,syr828";
+		reg = <0x41>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "VDD_GPU";
+		regulator-enable-ramp-delay = <300>;
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-ramp-delay = <8000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-output-names = "xin32k";
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>;
+	};
+
+	act8846: pmic@5a {
+		compatible = "active-semi,act8846";
+		reg = <0x5a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_vsel>, <&pwr_hold>;
+		system-power-controller;
+
+		regulators {
+			vcc_ddr: REG1 {
+				regulator-name = "VCC_DDR";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vcc_io: REG2 {
+				regulator-name = "VCC_IO";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_log: REG3 {
+				regulator-name = "VDD_LOG";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcc_20: REG4 {
+				regulator-name = "VCC_20";
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			vccio_sd: REG5 {
+				regulator-name = "VCCIO_SD";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd10_lcd: REG6 {
+				regulator-name = "VDD10_LCD";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcc_wl: REG7 {
+				regulator-name = "VCC_WL";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vcca_33: REG8 {
+				regulator-name = "VCCA_33";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vcc_lan: REG9 {
+				regulator-name = "VCC_LAN";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_10: REG10 {
+				regulator-name = "VDD_10";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcc_18: REG11 {
+				regulator-name = "VCC_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vcc18_lcd: REG12 {
+				regulator-name = "VCC18_LCD";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&pinctrl {
+	pcfg_output_high: pcfg-output-high {
+		output-high;
+	};
+
+	pcfg_output_low: pcfg-output-low {
+		output-low;
+	};
+
+	act8846 {
+		pmic_vsel: pmic-vsel {
+			rockchip,pins = <7 1 RK_FUNC_GPIO &pcfg_output_low>;
+		};
+
+		pwr_hold: pwr-hold {
+			rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+
+	buttons {
+		pwrbtn: pwrbtn {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		otg_vbus_drv: otg-vbus-drv {
+			rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pwm0 {
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcc_18>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	vmmc-supply = <&vcc_sdmmc>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host1 {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};