[1/2] ARM: dts: Add support for phyCORE-AM335x SoM

Message ID	1437035449-26956-1-git-send-email-t.remmet@phytec.de (mailing list archive)
State	New, archived
Headers	show Return-Path: <linux-omap-owner@kernel.org> From: Teresa Remmet <t.remmet@phytec.de> To: linux-omap@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org Cc: =?UTF-8?q?Beno=C3=AEt=20Cousson?= <bcousson@baylibre.com>, Tony Lindgren <tony@atomide.com>, Rob Herring <robh+dt@kernel.org>, Pawel Moll <pawel.moll@arm.com>, Mark Rutland <mark.rutland@arm.com>, Ian Campbell <ijc+devicetree@hellion.org.uk>, Kumar Gala <galak@codeaurora.org> Subject: [PATCH 1/2] ARM: dts: Add support for phyCORE-AM335x SoM Date: Thu, 16 Jul 2015 10:30:48 +0200 Message-Id: <1437035449-26956-1-git-send-email-t.remmet@phytec.de> Sender: linux-omap-owner@vger.kernel.org Precedence: bulk

On Thu, Jul 16, 2015 at 10:30:48AM +0200, Teresa Remmet wrote: > phyCORE-AM335x is a SoM (System on Module) containing > a AM335x SOC. The module can be connected to different > carrier boards. > > Some hardware parts are configurable on the phyCORE-AM335x. > So they are disabled on default in this som dtsi file. > They will be enabled in the board dts files, when populated. > > * RAM up to 1GiB > * PMIC > * NAND flash up to 1GiB > * Eth PHY on SOM: 1x RMII > * SPI NOR flash 8MiB (optional) > * i2c RTC (optional) > * i2c EEPROM 4kiB (optional) > > Signed-off-by: Teresa Remmet <t.remmet@phytec.de> > --- > arch/arm/boot/dts/am335x-phycore-som.dtsi | 368 ++++++++++++++++++++++++++++++ > 1 file changed, 368 insertions(+) > create mode 100644 arch/arm/boot/dts/am335x-phycore-som.dtsi > > diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi > new file mode 100644 > index 0000000..4d28fc3 > --- /dev/null > +++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi > @@ -0,0 +1,368 @@ > +/* > + * Copyright (C) 2015 Phytec Messtechnik GmbH > + * Author: Teresa Remmet <t.remmet@phytec.de> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include "am33xx.dtsi" > + > +/ { > + model = "Phytec AM335x phyCORE"; > + compatible = "phytec,am335x-phycore-som", "ti,am33xx"; One minor thing here...wildcards in compatible strings aren't permitted. However, family compatibles like "ti,am33xx" that came in before this was enforced are grandfathered. Ideally, the newly introced board/som specific strings should not propagate that wildcard. i.e. something like "phytec,am3352-phycore-som" or whatever is the base family part on these SOMs. -Matt > + > + aliases { > + rtc0 = &i2c_rtc; > + rtc1 = &rtc; > + }; > + > + cpus { > + cpu@0 { > + cpu0-supply = <&vdd1_reg>; > + }; > + }; > + > + memory { > + device_type = "memory"; > + reg = <0x80000000 0x10000000>; /* 256 MB */ > + }; > + > + vbat: fixedregulator@0 { > + compatible = "regulator-fixed"; > + }; > +}; > + > +/* Crypto Module */ > +&aes { > + status = "okay"; > +}; > + > +&sham { > + status = "okay"; > +}; > + > +/* Ethernet */ > +&am33xx_pinmux { > + ethernet0_pins: pinmux_ethernet0 { > + pinctrl-single,pins = < > + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */ > + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ > + 0x114 (PIN_OUTPUT | MUX_MODE1) /* mii1_txen.rmii1_txen */ > + 0x124 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ > + 0x128 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ > + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ > + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ > + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ > + >; > + }; > + > + mdio_pins: pinmux_mdio { > + pinctrl-single,pins = < > + /* MDIO */ > + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ > + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ > + >; > + }; > +}; > + > +&cpsw_emac0 { > + phy_id = <&davinci_mdio>, <0>; > + phy-mode = "rmii"; > + dual_emac_res_vlan = <1>; > +}; > + > +&davinci_mdio { > + pinctrl-names = "default"; > + pinctrl-0 = <&mdio_pins>; > + status = "okay"; > +}; > + > +&mac { > + slaves = <1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&ethernet0_pins>; > + status = "okay"; > +}; > + > +&phy_sel { > + rmii-clock-ext; > +}; > + > +/* I2C Busses */ > +&am33xx_pinmux { > + i2c0_pins: pinmux_i2c0 { > + pinctrl-single,pins = < > + 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */ > + 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */ > + >; > + }; > +}; > + > +&i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c0_pins>; > + clock-frequency = <400000>; > + status = "okay"; > + > + tps: pmic@2d { > + reg = <0x2d>; > + }; > + > + i2c_eeprom: eeprom@52 { > + compatible = "atmel,24c32"; > + pagesize = <32>; > + reg = <0x52>; > + status = "disabled"; > + }; > + > + i2c_rtc: rtc@68 { > + compatible = "rv4162"; > + reg = <0x68>; > + status = "disabled"; > + }; > +}; > + > +/* NAND memory */ > +&am33xx_pinmux { > + nandflash_pins: pinmux_nandflash { > + pinctrl-single,pins = < > + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ > + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ > + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ > + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ > + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ > + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ > + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ > + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ > + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ > + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ > + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ > + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ > + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ > + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ > + >; > + }; > +}; > + > +&elm { > + status = "okay"; > +}; > + > +&gpmc { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&nandflash_pins>; > + ranges = <0 0 0x08000000 0x1000000>; /* CS0: NAND */ > + nandflash: nand@0,0 { > + reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ > + nand-bus-width = <8>; > + ti,nand-ecc-opt = "bch8"; > + gpmc,device-nand = "true"; > + gpmc,device-width = <1>; > + gpmc,sync-clk-ps = <0>; > + gpmc,cs-on-ns = <0>; > + gpmc,cs-rd-off-ns = <30>; > + gpmc,cs-wr-off-ns = <30>; > + gpmc,adv-on-ns = <0>; > + gpmc,adv-rd-off-ns = <30>; > + gpmc,adv-wr-off-ns = <30>; > + gpmc,we-on-ns = <0>; > + gpmc,we-off-ns = <20>; > + gpmc,oe-on-ns = <10>; > + gpmc,oe-off-ns = <30>; > + gpmc,access-ns = <30>; > + gpmc,rd-cycle-ns = <30>; > + gpmc,wr-cycle-ns = <30>; > + gpmc,wait-on-read = "true"; > + gpmc,wait-on-write = "true"; > + gpmc,bus-turnaround-ns = <0>; > + gpmc,cycle2cycle-delay-ns = <50>; > + gpmc,cycle2cycle-diffcsen; > + gpmc,clk-activation-ns = <0>; > + gpmc,wait-monitoring-ns = <0>; > + gpmc,wr-access-ns = <30>; > + gpmc,wr-data-mux-bus-ns = <0>; > + > + elm_id = <&elm>; > + > + #address-cells = <1>; > + #size-cells = <1>; > + > + partition@0 { > + label = "xload"; > + reg = <0x0 0x20000>; > + }; > + partition@1 { > + label = "xload_backup1"; > + reg = <0x20000 0x20000>; > + }; > + partition@2 { > + label = "xload_backup2"; > + reg = <0x40000 0x20000>; > + }; > + partition@3 { > + label = "xload_backup3"; > + reg = <0x60000 0x20000>; > + }; > + partition@4 { > + label = "barebox"; > + reg = <0x80000 0x80000>; > + }; > + partition@5 { > + label = "bareboxenv"; > + reg = <0x100000 0x40000>; > + }; > + partition@6 { > + label = "oftree"; > + reg = <0x140000 0x40000>; > + }; > + partition@7 { > + label = "kernel"; > + reg = <0x180000 0x800000>; > + }; > + partition@8 { > + label = "root"; > + reg = <0x980000 0x0>; > + }; > + }; > +}; > + > +/* Power */ > +#include "tps65910.dtsi" > + > +&tps { > + vcc1-supply = <&vbat>; > + vcc2-supply = <&vbat>; > + vcc3-supply = <&vbat>; > + vcc4-supply = <&vbat>; > + vcc5-supply = <&vbat>; > + vcc6-supply = <&vbat>; > + vcc7-supply = <&vbat>; > + vccio-supply = <&vbat>; > + > + regulators { > + vrtc_reg: regulator@0 { > + regulator-always-on; > + }; > + > + vio_reg: regulator@1 { > + regulator-always-on; > + }; > + > + vdd1_reg: regulator@2 { > + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ > + regulator-name = "vdd_mpu"; > + regulator-min-microvolt = <912500>; > + regulator-max-microvolt = <1312500>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vdd2_reg: regulator@3 { > + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ > + regulator-name = "vdd_core"; > + regulator-min-microvolt = <912500>; > + regulator-max-microvolt = <1150000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vdd3_reg: regulator@4 { > + regulator-always-on; > + }; > + > + vdig1_reg: regulator@5 { > + regulator-name = "vdig1_1p8v"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vdig2_reg: regulator@6 { > + regulator-always-on; > + }; > + > + vpll_reg: regulator@7 { > + regulator-always-on; > + }; > + > + vdac_reg: regulator@8 { > + regulator-always-on; > + }; > + > + vaux1_reg: regulator@9 { > + regulator-always-on; > + }; > + > + vaux2_reg: regulator@10 { > + regulator-always-on; > + }; > + > + vaux33_reg: regulator@11 { > + regulator-always-on; > + }; > + > + vmmc_reg: regulator@12 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + }; > +}; > + > +&vbat { > + regulator-name = "vbat"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-boot-on; > +}; > + > +/* SPI Busses */ > +&am33xx_pinmux { > + spi0_pins: pinmux_spi0 { > + pinctrl-single,pins = < > + 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_clk.spi0_clk */ > + 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_d0.spi0_d0 */ > + 0x158 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d1.spi0_d1 */ > + 0x15c (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ > + >; > + }; > +}; > + > +&spi0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&spi0_pins>; > + status = "okay"; > + > + serial_flash: m25p80@0 { > + compatible = "m25p80"; > + spi-max-frequency = <48000000>; > + reg = <0x0>; > + m25p,fast-read; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + partition@0 { > + label = "xload"; > + reg = <0x0 0x20000>; > + }; > + partition@1 { > + label = "barebox"; > + reg = <0x20000 0x80000>; > + }; > + partition@2 { > + label = "bareboxenv"; > + reg = <0xa0000 0x20000>; > + }; > + partition@3 { > + label = "oftree"; > + reg = <0xc0000 0x20000>; > + }; > + partition@4 { > + label = "kernel"; > + reg = <0xe0000 0x0>; > + }; > + }; > +}; > -- > 1.9.1 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html

diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi new file mode 100644 index 0000000..4d28fc3 --- /dev/null +++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi @@ -0,0 +1,368 @@ +/* + * Copyright (C) 2015 Phytec Messtechnik GmbH + * Author: Teresa Remmet <t.remmet@phytec.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "am33xx.dtsi" + +/ { + model = "Phytec AM335x phyCORE"; + compatible = "phytec,am335x-phycore-som", "ti,am33xx"; + + aliases { + rtc0 = &i2c_rtc; + rtc1 = &rtc; + }; + + cpus { + cpu@0 { + cpu0-supply = <&vdd1_reg>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + vbat: fixedregulator@0 { + compatible = "regulator-fixed"; + }; +}; + +/* Crypto Module */ +&aes { + status = "okay"; +}; + +&sham { + status = "okay"; +}; + +/* Ethernet */ +&am33xx_pinmux { + ethernet0_pins: pinmux_ethernet0 { + pinctrl-single,pins = < + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ + 0x114 (PIN_OUTPUT | MUX_MODE1) /* mii1_txen.rmii1_txen */ + 0x124 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ + 0x128 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ + >; + }; + + mdio_pins: pinmux_mdio { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rmii"; + dual_emac_res_vlan = <1>; +}; + +&davinci_mdio { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + status = "okay"; +}; + +&mac { + slaves = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&ethernet0_pins>; + status = "okay"; +}; + +&phy_sel { + rmii-clock-ext; +}; + +/* I2C Busses */ +&am33xx_pinmux { + i2c0_pins: pinmux_i2c0 { + pinctrl-single,pins = < + 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + clock-frequency = <400000>; + status = "okay"; + + tps: pmic@2d { + reg = <0x2d>; + }; + + i2c_eeprom: eeprom@52 { + compatible = "atmel,24c32"; + pagesize = <32>; + reg = <0x52>; + status = "disabled"; + }; + + i2c_rtc: rtc@68 { + compatible = "rv4162"; + reg = <0x68>; + status = "disabled"; + }; +}; + +/* NAND memory */ +&am33xx_pinmux { + nandflash_pins: pinmux_nandflash { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; +}; + +&elm { + status = "okay"; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins>; + ranges = <0 0 0x08000000 0x1000000>; /* CS0: NAND */ + nandflash: nand@0,0 { + reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ + nand-bus-width = <8>; + ti,nand-ecc-opt = "bch8"; + gpmc,device-nand = "true"; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <30>; + gpmc,cs-wr-off-ns = <30>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <30>; + gpmc,adv-wr-off-ns = <30>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <20>; + gpmc,oe-on-ns = <10>; + gpmc,oe-off-ns = <30>; + gpmc,access-ns = <30>; + gpmc,rd-cycle-ns = <30>; + gpmc,wr-cycle-ns = <30>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <50>; + gpmc,cycle2cycle-diffcsen; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <30>; + gpmc,wr-data-mux-bus-ns = <0>; + + elm_id = <&elm>; + + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "xload"; + reg = <0x0 0x20000>; + }; + partition@1 { + label = "xload_backup1"; + reg = <0x20000 0x20000>; + }; + partition@2 { + label = "xload_backup2"; + reg = <0x40000 0x20000>; + }; + partition@3 { + label = "xload_backup3"; + reg = <0x60000 0x20000>; + }; + partition@4 { + label = "barebox"; + reg = <0x80000 0x80000>; + }; + partition@5 { + label = "bareboxenv"; + reg = <0x100000 0x40000>; + }; + partition@6 { + label = "oftree"; + reg = <0x140000 0x40000>; + }; + partition@7 { + label = "kernel"; + reg = <0x180000 0x800000>; + }; + partition@8 { + label = "root"; + reg = <0x980000 0x0>; + }; + }; +}; + +/* Power */ +#include "tps65910.dtsi" + +&tps { + vcc1-supply = <&vbat>; + vcc2-supply = <&vbat>; + vcc3-supply = <&vbat>; + vcc4-supply = <&vbat>; + vcc5-supply = <&vbat>; + vcc6-supply = <&vbat>; + vcc7-supply = <&vbat>; + vccio-supply = <&vbat>; + + regulators { + vrtc_reg: regulator@0 { + regulator-always-on; + }; + + vio_reg: regulator@1 { + regulator-always-on; + }; + + vdd1_reg: regulator@2 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1312500>; + regulator-boot-on; + regulator-always-on; + }; + + vdd2_reg: regulator@3 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd3_reg: regulator@4 { + regulator-always-on; + }; + + vdig1_reg: regulator@5 { + regulator-name = "vdig1_1p8v"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vdig2_reg: regulator@6 { + regulator-always-on; + }; + + vpll_reg: regulator@7 { + regulator-always-on; + }; + + vdac_reg: regulator@8 { + regulator-always-on; + }; + + vaux1_reg: regulator@9 { + regulator-always-on; + }; + + vaux2_reg: regulator@10 { + regulator-always-on; + }; + + vaux33_reg: regulator@11 { + regulator-always-on; + }; + + vmmc_reg: regulator@12 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; +}; + +&vbat { + regulator-name = "vbat"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; +}; + +/* SPI Busses */ +&am33xx_pinmux { + spi0_pins: pinmux_spi0 { + pinctrl-single,pins = < + 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_clk.spi0_clk */ + 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_d0.spi0_d0 */ + 0x158 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d1.spi0_d1 */ + 0x15c (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ + >; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>; + status = "okay"; + + serial_flash: m25p80@0 { + compatible = "m25p80"; + spi-max-frequency = <48000000>; + reg = <0x0>; + m25p,fast-read; + status = "disabled"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "xload"; + reg = <0x0 0x20000>; + }; + partition@1 { + label = "barebox"; + reg = <0x20000 0x80000>; + }; + partition@2 { + label = "bareboxenv"; + reg = <0xa0000 0x20000>; + }; + partition@3 { + label = "oftree"; + reg = <0xc0000 0x20000>; + }; + partition@4 { + label = "kernel"; + reg = <0xe0000 0x0>; + }; + }; +};

[1/2] ARM: dts: Add support for phyCORE-AM335x SoM

Commit Message

Comments

Patch