| Message ID | 1439812687-18259-1-git-send-email-srinivas.kandagatla@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 17 August 2015 at 13:58, Srinivas Kandagatla <srinivas.kandagatla@linaro.org> wrote: > Some of the pin-controllers like the Qualcomms "qcom,pm8921", which > require a pinconf to be setup to use pins as gpios. Using the pins > directly without pinconf setup would result in incorrect output voltage > or load settings. On the other hand pwrseq code does not configure the > pinctrl by default as it does not go thru the driver core. > > This patch adds a call to pinctrl_bind_pins() to bind pins which > are going to be used as gpios. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Thanks, applied for next! I add the "mmc:" to the prefix of the commit message header. Kind regards Uffe > --- > drivers/mmc/core/pwrseq.c | 5 +++++ > 1 file changed, 5 insertions(+) > > diff --git a/drivers/mmc/core/pwrseq.c b/drivers/mmc/core/pwrseq.c > index 4c1d175..6e5d8b3 100644 > --- a/drivers/mmc/core/pwrseq.c > +++ b/drivers/mmc/core/pwrseq.c > @@ -12,6 +12,7 @@ > #include <linux/err.h> > #include <linux/of.h> > #include <linux/of_platform.h> > +#include <linux/pinctrl/devinfo.h> > > #include <linux/mmc/host.h> > > @@ -65,6 +66,10 @@ int mmc_pwrseq_alloc(struct mmc_host *host) > goto err; > } > > + ret = pinctrl_bind_pins(&pdev->dev); > + if (ret) > + goto err; > + > match = mmc_pwrseq_find(np); > if (IS_ERR(match)) { > ret = PTR_ERR(match); > -- > 1.9.1 > -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
+ Stephen Rothwell On 25 August 2015 at 14:06, Ulf Hansson <ulf.hansson@linaro.org> wrote: > On 17 August 2015 at 13:58, Srinivas Kandagatla > <srinivas.kandagatla@linaro.org> wrote: >> Some of the pin-controllers like the Qualcomms "qcom,pm8921", which >> require a pinconf to be setup to use pins as gpios. Using the pins >> directly without pinconf setup would result in incorrect output voltage >> or load settings. On the other hand pwrseq code does not configure the >> pinctrl by default as it does not go thru the driver core. >> >> This patch adds a call to pinctrl_bind_pins() to bind pins which >> are going to be used as gpios. >> >> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > > Thanks, applied for next! I add the "mmc:" to the prefix of the commit > message header. This went in too quickly, my bad! The kbuild test robot reports an error when building i386 with allmodconfig, so I will drop this patch from my next branch. https://lists.01.org/pipermail/kbuild-all/2015-August/011806.html Moreover I have some more comment around the patch, see below. > > Kind regards > Uffe > >> --- >> drivers/mmc/core/pwrseq.c | 5 +++++ >> 1 file changed, 5 insertions(+) >> >> diff --git a/drivers/mmc/core/pwrseq.c b/drivers/mmc/core/pwrseq.c >> index 4c1d175..6e5d8b3 100644 >> --- a/drivers/mmc/core/pwrseq.c >> +++ b/drivers/mmc/core/pwrseq.c >> @@ -12,6 +12,7 @@ >> #include <linux/err.h> >> #include <linux/of.h> >> #include <linux/of_platform.h> >> +#include <linux/pinctrl/devinfo.h> >> >> #include <linux/mmc/host.h> >> >> @@ -65,6 +66,10 @@ int mmc_pwrseq_alloc(struct mmc_host *host) >> goto err; >> } >> >> + ret = pinctrl_bind_pins(&pdev->dev); pinctrl_bind_bins() uses devm_* functions and that's not going to work as the used device here isn't being probed/released. Instead you need to use the *non* devm_pinctrl_*() APIs, such as pinctrl_get|put() etc. >> + if (ret) >> + goto err; >> + >> match = mmc_pwrseq_find(np); >> if (IS_ERR(match)) { >> ret = PTR_ERR(match); >> -- >> 1.9.1 >> Kind regards Uffe -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/mmc/core/pwrseq.c b/drivers/mmc/core/pwrseq.c index 4c1d175..6e5d8b3 100644 --- a/drivers/mmc/core/pwrseq.c +++ b/drivers/mmc/core/pwrseq.c @@ -12,6 +12,7 @@ #include <linux/err.h> #include <linux/of.h> #include <linux/of_platform.h> +#include <linux/pinctrl/devinfo.h> #include <linux/mmc/host.h> @@ -65,6 +66,10 @@ int mmc_pwrseq_alloc(struct mmc_host *host) goto err; } + ret = pinctrl_bind_pins(&pdev->dev); + if (ret) + goto err; + match = mmc_pwrseq_find(np); if (IS_ERR(match)) { ret = PTR_ERR(match);
Some of the pin-controllers like the Qualcomms "qcom,pm8921", which require a pinconf to be setup to use pins as gpios. Using the pins directly without pinconf setup would result in incorrect output voltage or load settings. On the other hand pwrseq code does not configure the pinctrl by default as it does not go thru the driver core. This patch adds a call to pinctrl_bind_pins() to bind pins which are going to be used as gpios. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> --- drivers/mmc/core/pwrseq.c | 5 +++++ 1 file changed, 5 insertions(+)