diff --git a/Documentation/devicetree/bindings/arm/uniphier/cache-uniphier.txt b/Documentation/devicetree/bindings/arm/uniphier/cache-uniphier.txt
new file mode 100644
index 0000000..ce6eddd
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/uniphier/cache-uniphier.txt
@@ -0,0 +1,48 @@
+UniPhier outer cache controller
+
+UniPhier SoCs are integrated with a full-custom outer cache controller system.
+All of them have a level 2 cache controller, and some have a level 3 cache
+controller as well.
+
+Required properties:
+- compatible: should be "socionext,uniphier-system-cache"
+- reg: offsets and lengths of the register sets for the device.  It should
+  contain 3 regions: control register, revision register, operation register,
+  in this order.
+- cache-unified: specifies the cache is a unified cache.
+- cache-size: specifies the size in bytes of the cache
+- cache-sets: specifies the number of associativity sets of the cache
+- cache-line-size: specifies the line size in bytes
+- cache-level: specifies the level in the cache hierarchy.  The value should
+  be 2 for L2 cache, 3 for L3 cache, etc.
+
+Optional properties:
+- next-level-cache: phandle to the next level cache if present.  The next level
+  cache should be also compatible with "socionext,uniphier-system-cache".
+
+The L2 cache must exist to use the L3 cache; the cache hierarchy must be
+indicated correctly with "next-level-cache" properties.
+
+Example:
+	l2: l2-cache@500c0000 {
+		compatible = "socionext,uniphier-system-cache";
+		reg = <0x500c0000 0x2000>, <0x503c0100 0x8>,
+		      <0x506c0000 0x400>;
+		cache-unified;
+		cache-size = <0x200000>;
+		cache-sets = <512>;
+		cache-line-size = <128>;
+		cache-level = <2>;
+		next-level-cache = <&l3>;
+	};
+
+	l3: l3-cache@500c8000 {
+		compatible = "socionext,uniphier-system-cache";
+		reg = <0x500c8000 0x2000>, <0x503c8100 0x8>,
+		      <0x506c8000 0x400>;
+		cache-unified;
+		cache-size = <0x400000>;
+		cache-sets = <512>;
+		cache-line-size = <256>;
+		cache-level = <3>;
+	};
diff --git a/MAINTAINERS b/MAINTAINERS
index 7ba7ab7..e9c5dd9 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1600,7 +1600,9 @@ M:	Masahiro Yamada <yamada.masahiro@socionext.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/boot/dts/uniphier*
+F:	arch/arm/include/asm/hardware/cache-uniphier.h
 F:	arch/arm/mach-uniphier/
+F:	arch/arm/mm/cache-uniphier.c
 F:	drivers/pinctrl/uniphier/
 F:	drivers/tty/serial/8250/8250_uniphier.c
 N:	uniphier
diff --git a/arch/arm/include/asm/hardware/cache-uniphier.h b/arch/arm/include/asm/hardware/cache-uniphier.h
new file mode 100644
index 0000000..102e3fb
--- /dev/null
+++ b/arch/arm/include/asm/hardware/cache-uniphier.h
@@ -0,0 +1,46 @@
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __CACHE_UNIPHIER_H
+#define __CACHE_UNIPHIER_H
+
+#include <linux/types.h>
+
+#ifdef CONFIG_CACHE_UNIPHIER
+int uniphier_cache_init(void);
+int uniphier_cache_l2_is_enabled(void);
+void uniphier_cache_l2_touch_range(unsigned long start, unsigned long end);
+void uniphier_cache_l2_set_locked_ways(u32 way_mask);
+#else
+static inline int uniphier_cache_init(void)
+{
+	return -ENODEV;
+}
+
+static inline int uniphier_cache_l2_is_enabled(void)
+{
+	return 0;
+}
+
+static inline void uniphier_cache_l2_touch_range(unsigned long start,
+						 unsigned long end)
+{
+}
+
+static inline void uniphier_cache_l2_set_locked_ways(u32 way_mask)
+{
+}
+#endif
+
+#endif /* __CACHE_UNIPHIER_H */
diff --git a/arch/arm/kernel/irq.c b/arch/arm/kernel/irq.c
index 5ff4826..1e8c747 100644
--- a/arch/arm/kernel/irq.c
+++ b/arch/arm/kernel/irq.c
@@ -39,6 +39,7 @@
 #include <linux/export.h>
 
 #include <asm/hardware/cache-l2x0.h>
+#include <asm/hardware/cache-uniphier.h>
 #include <asm/outercache.h>
 #include <asm/exception.h>
 #include <asm/mach/arch.h>
@@ -117,6 +118,8 @@ void __init init_IRQ(void)
 		if (ret)
 			pr_err("L2C: failed to init: %d\n", ret);
 	}
+
+	uniphier_cache_init();
 }
 
 #ifdef CONFIG_MULTI_IRQ_HANDLER
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index df7537f..a2e74b2 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -986,6 +986,16 @@ config CACHE_TAUROS2
 	  This option enables the Tauros2 L2 cache controller (as
 	  found on PJ1/PJ4).
 
+config CACHE_UNIPHIER
+	bool "Enable the UniPhier outer cache controller"
+	depends on ARCH_UNIPHIER
+	default y
+	select OUTER_CACHE
+	select OUTER_CACHE_SYNC
+	help
+	  This option enables the UniPhier outer cache (system cache)
+	  controller.
+
 config CACHE_XSC3L2
 	bool "Enable the L2 cache on XScale3"
 	depends on CPU_XSC3
diff --git a/arch/arm/mm/Makefile b/arch/arm/mm/Makefile
index 57c8df5..7f76d96 100644
--- a/arch/arm/mm/Makefile
+++ b/arch/arm/mm/Makefile
@@ -103,3 +103,4 @@ obj-$(CONFIG_CACHE_FEROCEON_L2)	+= cache-feroceon-l2.o
 obj-$(CONFIG_CACHE_L2X0)	+= cache-l2x0.o l2c-l2x0-resume.o
 obj-$(CONFIG_CACHE_XSC3L2)	+= cache-xsc3l2.o
 obj-$(CONFIG_CACHE_TAUROS2)	+= cache-tauros2.o
+obj-$(CONFIG_CACHE_UNIPHIER)	+= cache-uniphier.o
diff --git a/arch/arm/mm/cache-uniphier.c b/arch/arm/mm/cache-uniphier.c
new file mode 100644
index 0000000..66139a9
--- /dev/null
+++ b/arch/arm/mm/cache-uniphier.c
@@ -0,0 +1,544 @@
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#define pr_fmt(fmt)		"uniphier: " fmt
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/log2.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+#include <asm/hardware/cache-uniphier.h>
+#include <asm/outercache.h>
+
+/* control registers */
+#define UNIPHIER_SSCC		0x0	/* Control Register */
+#define    UNIPHIER_SSCC_BST			BIT(20)	/* UCWG burst read */
+#define    UNIPHIER_SSCC_ACT			BIT(19)	/* Inst-Data separate */
+#define    UNIPHIER_SSCC_WTG			BIT(18)	/* WT gathering on */
+#define    UNIPHIER_SSCC_PRD			BIT(17)	/* enable pre-fetch */
+#define    UNIPHIER_SSCC_ON			BIT(0)	/* enable cache */
+#define UNIPHIER_SSCLPDAWCR	0x30	/* Unified/Data Active Way Control */
+#define UNIPHIER_SSCLPIAWCR	0x34	/* Instruction Active Way Control */
+
+/* revision registers */
+#define UNIPHIER_SSCID		0x0	/* ID Register */
+
+/* operation registers */
+#define UNIPHIER_SSCOPE		0x244	/* Cache Operation Primitive Entry */
+#define    UNIPHIER_SSCOPE_CM_INV		0x0	/* invalidate */
+#define    UNIPHIER_SSCOPE_CM_CLEAN		0x1	/* clean */
+#define    UNIPHIER_SSCOPE_CM_FLUSH		0x2	/* flush */
+#define    UNIPHIER_SSCOPE_CM_SYNC		0x8	/* sync (drain bufs) */
+#define    UNIPHIER_SSCOPE_CM_FLUSH_PREFETCH	0x9	/* flush p-fetch buf */
+#define UNIPHIER_SSCOQM		0x248	/* Cache Operation Queue Mode */
+#define    UNIPHIER_SSCOQM_TID_MASK		(0x3 << 21)
+#define    UNIPHIER_SSCOQM_TID_LRU_DATA		(0x0 << 21)
+#define    UNIPHIER_SSCOQM_TID_LRU_INST		(0x1 << 21)
+#define    UNIPHIER_SSCOQM_TID_WAY		(0x2 << 21)
+#define    UNIPHIER_SSCOQM_S_MASK		(0x3 << 17)
+#define    UNIPHIER_SSCOQM_S_RANGE		(0x0 << 17)
+#define    UNIPHIER_SSCOQM_S_ALL		(0x1 << 17)
+#define    UNIPHIER_SSCOQM_S_WAY		(0x2 << 17)
+#define    UNIPHIER_SSCOQM_CE			BIT(15)	/* notify completion */
+#define    UNIPHIER_SSCOQM_CM_INV		0x0	/* invalidate */
+#define    UNIPHIER_SSCOQM_CM_CLEAN		0x1	/* clean */
+#define    UNIPHIER_SSCOQM_CM_FLUSH		0x2	/* flush */
+#define    UNIPHIER_SSCOQM_CM_PREFETCH		0x3	/* prefetch to cache */
+#define    UNIPHIER_SSCOQM_CM_PREFETCH_BUF	0x4	/* prefetch to pf-buf */
+#define    UNIPHIER_SSCOQM_CM_TOUCH		0x5	/* touch */
+#define    UNIPHIER_SSCOQM_CM_TOUCH_ZERO	0x6	/* touch to zero */
+#define    UNIPHIER_SSCOQM_CM_TOUCH_DIRTY	0x7	/* touch with dirty */
+#define UNIPHIER_SSCOQAD	0x24c	/* Cache Operation Queue Address */
+#define UNIPHIER_SSCOQSZ	0x250	/* Cache Operation Queue Size */
+#define UNIPHIER_SSCOQMASK	0x254	/* Cache Operation Queue Address Mask */
+#define UNIPHIER_SSCOQWN	0x258	/* Cache Operation Queue Way Number */
+#define UNIPHIER_SSCOPPQSEF	0x25c	/* Cache Operation Queue Set Complete*/
+#define    UNIPHIER_SSCOPPQSEF_FE		BIT(1)
+#define    UNIPHIER_SSCOPPQSEF_OE		BIT(0)
+#define UNIPHIER_SSCOLPQS	0x260	/* Cache Operation Queue Status */
+#define    UNIPHIER_SSCOLPQS_EF			BIT(2)
+#define    UNIPHIER_SSCOLPQS_EST		BIT(1)
+#define    UNIPHIER_SSCOLPQS_QST		BIT(0)
+
+/* Is the touch/pre-fetch destination specified by ways? */
+#define UNIPHIER_SSCOQM_TID_IS_WAY(op) \
+		((op & UNIPHIER_SSCOQM_TID_MASK) == UNIPHIER_SSCOQM_TID_WAY)
+/* Is the operation region specified by address range? */
+#define UNIPHIER_SSCOQM_S_IS_RANGE(op) \
+		((op & UNIPHIER_SSCOQM_S_MASK) == UNIPHIER_SSCOQM_S_RANGE)
+
+/**
+ * uniphier_cache_data - UniPhier outer cache specific data
+ *
+ * @ctrl_base: virtual base address of control registers
+ * @rev_base: virtual base address of revision registers
+ * @op_base: virtual base address of operation registers
+ * @way_present_mask: each bit specifies if the way is present
+ * @way_locked_mask: each bit specifies if the way is locked
+ * @nsets: number of associativity sets
+ * @line_size: line size in bytes
+ * @range_op_max_size: max size that can be handled by a single range operation
+ * @list: list node to include this level in the whole cache hierarchy
+ */
+struct uniphier_cache_data {
+	void __iomem *ctrl_base;
+	void __iomem *rev_base;
+	void __iomem *op_base;
+	u32 way_present_mask;
+	u32 way_locked_mask;
+	u32 nsets;
+	u32 line_size;
+	u32 range_op_max_size;
+	struct list_head list;
+};
+
+/*
+ * List of the whole outer cache hierarchy.  This list is only modified during
+ * the early boot stage, so no mutex is taken for the access to the list.
+ */
+static LIST_HEAD(uniphier_cache_list);
+
+/**
+ * __uniphier_cache_sync - perform a sync point for a particular cache level
+ *
+ * @data: cache controller specific data
+ */
+static void __uniphier_cache_sync(struct uniphier_cache_data *data)
+{
+	/* This sequence need not be atomic.  Do not disable IRQ. */
+	writel_relaxed(UNIPHIER_SSCOPE_CM_SYNC,
+		       data->op_base + UNIPHIER_SSCOPE);
+	/* need a read back to confirm */
+	readl_relaxed(data->op_base + UNIPHIER_SSCOPE);
+}
+
+/**
+ * __uniphier_cache_maint_common - run a queue operation for a particular level
+ *
+ * @data: cache controller specific data
+ * @start: start address of range operation (don't care for "all" operation)
+ * @size: data size of range operation (don't care for "all" operation)
+ * @operation: flags to specify the desired cache operation
+ */
+static void __uniphier_cache_maint_common(struct uniphier_cache_data *data,
+					  unsigned long start,
+					  unsigned long size,
+					  u32 operation)
+{
+	unsigned long flags;
+
+	/*
+	 * The IRQ must be disable during this sequence because the accessor
+	 * holds the access right of the operation queue registers.  The IRQ
+	 * should be restored after releasing the register access right.
+	 */
+	local_irq_save(flags);
+
+	/* clear the complete notification flag */
+	writel_relaxed(UNIPHIER_SSCOLPQS_EF, data->op_base + UNIPHIER_SSCOLPQS);
+
+	/*
+	 * We do not need a spin lock here because the hardware guarantees
+	 * this sequence is atomic, i.e. the write access is arbitrated
+	 * and only the winner's write accesses take effect.
+	 * After register settings, we need to check the UNIPHIER_SSCOPPQSEF to
+	 * see if we won the arbitration or not.
+	 * If the command was not successfully set, just try again.
+	 */
+	do {
+		/* set cache operation */
+		writel_relaxed(UNIPHIER_SSCOQM_CE | operation,
+			       data->op_base + UNIPHIER_SSCOQM);
+
+		/* set address range if needed */
+		if (likely(UNIPHIER_SSCOQM_S_IS_RANGE(operation))) {
+			writel_relaxed(start, data->op_base + UNIPHIER_SSCOQAD);
+			writel_relaxed(size, data->op_base + UNIPHIER_SSCOQSZ);
+		}
+
+		/* set target ways if needed */
+		if (unlikely(UNIPHIER_SSCOQM_TID_IS_WAY(operation)))
+			writel_relaxed(data->way_locked_mask,
+				       data->op_base + UNIPHIER_SSCOQWN);
+	} while (unlikely(readl_relaxed(data->op_base + UNIPHIER_SSCOPPQSEF) &
+			  (UNIPHIER_SSCOPPQSEF_FE | UNIPHIER_SSCOPPQSEF_OE)));
+
+	/* wait until the operation is completed */
+	while (likely(readl_relaxed(data->op_base + UNIPHIER_SSCOLPQS) !=
+		      UNIPHIER_SSCOLPQS_EF))
+		cpu_relax();
+
+	local_irq_restore(flags);
+}
+
+static void __uniphier_cache_maint_all(struct uniphier_cache_data *data,
+				       u32 operation)
+{
+	__uniphier_cache_maint_common(data, 0, 0,
+				      UNIPHIER_SSCOQM_S_ALL | operation);
+
+	__uniphier_cache_sync(data);
+}
+
+static void __uniphier_cache_maint_range(struct uniphier_cache_data *data,
+					 unsigned long start, unsigned long end,
+					 u32 operation)
+{
+	unsigned long size;
+
+	/*
+	 * If the start address is not aligned,
+	 * perform a cache operation for the first cache-line
+	 */
+	start = start & ~(data->line_size - 1);
+
+	size = end - start;
+
+	if (unlikely(size >= (unsigned long)(-data->line_size))) {
+		/* this means cache operation for all range */
+		__uniphier_cache_maint_all(data, operation);
+		return;
+	}
+
+	/*
+	 * If the end address is not aligned,
+	 * perform a cache operation for the last cache-line
+	 */
+	size = ALIGN(size, data->line_size);
+
+	while (size) {
+		unsigned long chunk_size = min_t(unsigned long, size,
+						 data->range_op_max_size);
+
+		__uniphier_cache_maint_common(data, start, chunk_size,
+					UNIPHIER_SSCOQM_S_RANGE | operation);
+
+		start += chunk_size;
+		size -= chunk_size;
+	}
+
+	__uniphier_cache_sync(data);
+}
+
+static void __uniphier_cache_enable(struct uniphier_cache_data *data, bool on)
+{
+	u32 val = 0;
+
+	if (on)
+		val = UNIPHIER_SSCC_WTG | UNIPHIER_SSCC_PRD | UNIPHIER_SSCC_ON;
+
+	writel_relaxed(val, data->ctrl_base + UNIPHIER_SSCC);
+}
+
+static void __uniphier_cache_set_locked_ways(struct uniphier_cache_data *data,
+					     u32 way_mask)
+{
+	data->way_locked_mask = way_mask & data->way_present_mask;
+
+	writel_relaxed(~data->way_locked_mask & data->way_present_mask,
+		       data->ctrl_base + UNIPHIER_SSCLPDAWCR);
+}
+
+static void uniphier_cache_maint_range(unsigned long start, unsigned long end,
+				       u32 operation)
+{
+	struct uniphier_cache_data *data;
+
+	list_for_each_entry(data, &uniphier_cache_list, list)
+		__uniphier_cache_maint_range(data, start, end, operation);
+}
+
+static void uniphier_cache_maint_all(u32 operation)
+{
+	struct uniphier_cache_data *data;
+
+	list_for_each_entry(data, &uniphier_cache_list, list)
+		__uniphier_cache_maint_all(data, operation);
+}
+
+static void uniphier_cache_inv_range(unsigned long start, unsigned long end)
+{
+	uniphier_cache_maint_range(start, end, UNIPHIER_SSCOQM_CM_INV);
+}
+
+static void uniphier_cache_clean_range(unsigned long start, unsigned long end)
+{
+	uniphier_cache_maint_range(start, end, UNIPHIER_SSCOQM_CM_CLEAN);
+}
+
+static void uniphier_cache_flush_range(unsigned long start, unsigned long end)
+{
+	uniphier_cache_maint_range(start, end, UNIPHIER_SSCOQM_CM_FLUSH);
+}
+
+static void __init uniphier_cache_inv_all(void)
+{
+	uniphier_cache_maint_all(UNIPHIER_SSCOQM_CM_INV);
+}
+
+static void uniphier_cache_flush_all(void)
+{
+	uniphier_cache_maint_all(UNIPHIER_SSCOQM_CM_FLUSH);
+}
+
+static void uniphier_cache_disable(void)
+{
+	struct uniphier_cache_data *data;
+
+	list_for_each_entry_reverse(data, &uniphier_cache_list, list)
+		__uniphier_cache_enable(data, false);
+
+	uniphier_cache_flush_all();
+}
+
+static void __init uniphier_cache_enable(void)
+{
+	struct uniphier_cache_data *data;
+
+	uniphier_cache_inv_all();
+
+	list_for_each_entry(data, &uniphier_cache_list, list) {
+		__uniphier_cache_enable(data, true);
+		__uniphier_cache_set_locked_ways(data, 0);
+	}
+}
+
+static void uniphier_cache_sync(void)
+{
+	struct uniphier_cache_data *data;
+
+	list_for_each_entry(data, &uniphier_cache_list, list)
+		__uniphier_cache_sync(data);
+}
+
+int __init uniphier_cache_l2_is_enabled(void)
+{
+	struct uniphier_cache_data *data;
+
+	data = list_first_entry_or_null(&uniphier_cache_list,
+					struct uniphier_cache_data, list);
+	if (!data)
+		return 0;
+
+	return !!(readl_relaxed(data->ctrl_base + UNIPHIER_SSCC) &
+		  UNIPHIER_SSCC_ON);
+}
+
+void __init uniphier_cache_l2_touch_range(unsigned long start,
+					  unsigned long end)
+{
+	struct uniphier_cache_data *data;
+
+	data = list_first_entry_or_null(&uniphier_cache_list,
+					struct uniphier_cache_data, list);
+	if (data)
+		__uniphier_cache_maint_range(data, start, end,
+					     UNIPHIER_SSCOQM_TID_WAY |
+					     UNIPHIER_SSCOQM_CM_TOUCH);
+}
+
+void __init uniphier_cache_l2_set_locked_ways(u32 way_mask)
+{
+	struct uniphier_cache_data *data;
+
+	data = list_first_entry_or_null(&uniphier_cache_list,
+					struct uniphier_cache_data, list);
+	if (data)
+		__uniphier_cache_set_locked_ways(data, way_mask);
+}
+
+static const struct of_device_id uniphier_cache_match[] __initconst = {
+	{
+		.compatible = "socionext,uniphier-system-cache",
+	},
+	{ /* sentinel */ }
+};
+
+static struct device_node * __init uniphier_cache_get_next_level_node(
+							struct device_node *np)
+{
+	u32 phandle;
+
+	if (of_property_read_u32(np, "next-level-cache", &phandle))
+		return NULL;
+
+	return of_find_node_by_phandle(phandle);
+}
+
+static int __init __uniphier_cache_init(struct device_node *np,
+					unsigned int *cache_level)
+{
+	struct uniphier_cache_data *data;
+	u32 level, cache_size;
+	struct device_node *next_np;
+	int ret = 0;
+
+	if (!of_match_node(uniphier_cache_match, np)) {
+		pr_err("L%d: not compatible with uniphier cache\n",
+		       *cache_level);
+		return -EINVAL;
+	}
+
+	if (of_property_read_u32(np, "cache-level", &level)) {
+		pr_err("L%d: cache-level is not specified\n", *cache_level);
+		return -EINVAL;
+	}
+
+	if (level != *cache_level) {
+		pr_err("L%d: cache-level is unexpected value %d\n",
+		       *cache_level, level);
+		return -EINVAL;
+	}
+
+	if (!of_property_read_bool(np, "cache-unified")) {
+		pr_err("L%d: cache-unified is not specified\n", *cache_level);
+		return -EINVAL;
+	}
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	if (of_property_read_u32(np, "cache-line-size", &data->line_size) ||
+	    !is_power_of_2(data->line_size)) {
+		pr_err("L%d: cache-line-size is unspecified or invalid\n",
+		       *cache_level);
+		ret = -EINVAL;
+		goto err;
+	}
+
+	if (of_property_read_u32(np, "cache-sets", &data->nsets) ||
+	    !is_power_of_2(data->nsets)) {
+		pr_err("L%d: cache-sets is unspecified or invalid\n",
+		       *cache_level);
+		ret = -EINVAL;
+		goto err;
+	}
+
+	if (of_property_read_u32(np, "cache-size", &cache_size) ||
+	    cache_size == 0 || cache_size % (data->nsets * data->line_size)) {
+		pr_err("L%d: cache-size is unspecified or invalid\n",
+		       *cache_level);
+		ret = -EINVAL;
+		goto err;
+	}
+
+	data->way_present_mask =
+		((u32)1 << cache_size / data->nsets / data->line_size) - 1;
+
+	data->ctrl_base = of_iomap(np, 0);
+	if (!data->ctrl_base) {
+		pr_err("L%d: failed to map control register\n", *cache_level);
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	data->rev_base = of_iomap(np, 1);
+	if (!data->rev_base) {
+		pr_err("L%d: failed to map revision register\n", *cache_level);
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	data->op_base = of_iomap(np, 2);
+	if (!data->op_base) {
+		pr_err("L%d: failed to map operation register\n", *cache_level);
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	if (*cache_level == 2) {
+		u32 revision = readl(data->rev_base + UNIPHIER_SSCID);
+		/*
+		 * The size of range operation is limited to (1 << 22) or less
+		 * for PH-sLD8 or older SoCs.
+		 */
+		if (revision <= 0x16)
+			data->range_op_max_size = (u32)1 << 22;
+	}
+
+	data->range_op_max_size -= data->line_size;
+
+	INIT_LIST_HEAD(&data->list);
+	list_add_tail(&data->list, &uniphier_cache_list); /* no mutex */
+
+	/*
+	 * OK, this level has been successfully initialized.  Look for the next
+	 * level cache.  Do not roll back even if the initialization of the
+	 * next level cache fails because we want to continue with available
+	 * cache levels.
+	 */
+	next_np = uniphier_cache_get_next_level_node(np);
+	if (next_np) {
+		(*cache_level)++;
+		ret = __uniphier_cache_init(next_np, cache_level);
+	}
+	of_node_put(next_np);
+
+	return ret;
+err:
+	iounmap(data->op_base);
+	iounmap(data->rev_base);
+	iounmap(data->ctrl_base);
+	kfree(data);
+
+	return ret;
+}
+
+int __init uniphier_cache_init(void)
+{
+	struct device_node *np = NULL;
+	unsigned int cache_level;
+	int ret = 0;
+
+	/* look for level 2 cache */
+	while ((np = of_find_matching_node(np, uniphier_cache_match)))
+		if (!of_property_read_u32(np, "cache-level", &cache_level) &&
+		    cache_level == 2)
+			break;
+
+	if (!np)
+		return -ENODEV;
+
+	ret = __uniphier_cache_init(np, &cache_level);
+	of_node_put(np);
+
+	if (ret) {
+		/*
+		 * Error out iif L2 initialization fails.  Continue with any
+		 * error on L3 or outer because they are optional.
+		 */
+		if (cache_level == 2) {
+			pr_err("failed to initialize L2 cache\n");
+			return ret;
+		}
+
+		cache_level--;
+		ret = 0;
+	}
+
+	outer_cache.inv_range = uniphier_cache_inv_range;
+	outer_cache.clean_range = uniphier_cache_clean_range;
+	outer_cache.flush_range = uniphier_cache_flush_range;
+	outer_cache.flush_all = uniphier_cache_flush_all;
+	outer_cache.disable = uniphier_cache_disable;
+	outer_cache.sync = uniphier_cache_sync;
+
+	uniphier_cache_enable();
+
+	pr_info("enabled outer cache (cache level: %d)\n", cache_level);
+
+	return ret;
+}
