diff mbox

[v2] drm/i915: set proper N/CTS in modeset

Message ID 1443144972-81982-1-git-send-email-libin.yang@intel.com (mailing list archive)
State New, archived
Headers show

Commit Message

Yang, Libin Sept. 25, 2015, 1:36 a.m. UTC
From: Libin Yang <libin.yang@intel.com>

When modeset occurs and the TMDS frequency is set to some
speical values, the N/CTS need to be set manually if audio
is playing.

Signed-off-by: Libin Yang <libin.yang@intel.com>
---
 drivers/gpu/drm/i915/intel_audio.c | 57 ++++++++++++++++++++++++++++++++------
 include/drm/i915_component.h       | 10 +++++++
 2 files changed, 58 insertions(+), 9 deletions(-)

Comments

Jani Nikula Sept. 25, 2015, 8:01 a.m. UTC | #1
On Fri, 25 Sep 2015, libin.yang@intel.com wrote:
> From: Libin Yang <libin.yang@intel.com>
>
> When modeset occurs and the TMDS frequency is set to some
> speical values, the N/CTS need to be set manually if audio
> is playing.
>
> Signed-off-by: Libin Yang <libin.yang@intel.com>

Reviewed-by: Jani Nikula <jani.nikula@intel.com>


> ---
>  drivers/gpu/drm/i915/intel_audio.c | 57 ++++++++++++++++++++++++++++++++------
>  include/drm/i915_component.h       | 10 +++++++
>  2 files changed, 58 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_audio.c b/drivers/gpu/drm/i915/intel_audio.c
> index e3c32ce..642dfbd 100644
> --- a/drivers/gpu/drm/i915/intel_audio.c
> +++ b/drivers/gpu/drm/i915/intel_audio.c
> @@ -128,6 +128,20 @@ static int audio_config_get_n(const struct drm_display_mode *mode, int rate)
>  	return 0;
>  }
>  
> +static uint32_t audio_config_setup_n_reg(int n, uint32_t val)
> +{
> +	int n_low, n_up;
> +	uint32_t tmp = val;
> +
> +	n_low = n & 0xfff;
> +	n_up = (n >> 12) & 0xff;
> +	tmp &= ~(AUD_CONFIG_UPPER_N_MASK | AUD_CONFIG_LOWER_N_MASK);
> +	tmp |= ((n_up << AUD_CONFIG_UPPER_N_SHIFT) |
> +			(n_low << AUD_CONFIG_LOWER_N_SHIFT) |
> +			AUD_CONFIG_N_PROG_ENABLE);
> +	return tmp;
> +}
> +
>  /* check whether N/CTS/M need be set manually */
>  static bool audio_rate_need_prog(struct intel_crtc *crtc,
>  					struct drm_display_mode *mode)
> @@ -262,9 +276,14 @@ static void hsw_audio_codec_enable(struct drm_connector *connector,
>  	struct drm_i915_private *dev_priv = connector->dev->dev_private;
>  	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
>  	enum pipe pipe = intel_crtc->pipe;
> +	struct i915_audio_component *acomp = dev_priv->audio_component;
>  	const uint8_t *eld = connector->eld;
> +	struct intel_digital_port *intel_dig_port =
> +		enc_to_dig_port(&encoder->base);
> +	enum port port = intel_dig_port->port;
>  	uint32_t tmp;
>  	int len, i;
> +	int n, rate;
>  
>  	DRM_DEBUG_KMS("Enable audio codec on pipe %c, %u bytes ELD\n",
>  		      pipe_name(pipe), drm_eld_size(eld));
> @@ -302,12 +321,29 @@ static void hsw_audio_codec_enable(struct drm_connector *connector,
>  	/* Enable timestamps */
>  	tmp = I915_READ(HSW_AUD_CFG(pipe));
>  	tmp &= ~AUD_CONFIG_N_VALUE_INDEX;
> -	tmp &= ~AUD_CONFIG_N_PROG_ENABLE;
>  	tmp &= ~AUD_CONFIG_PIXEL_CLOCK_HDMI_MASK;
>  	if (intel_pipe_has_type(intel_crtc, INTEL_OUTPUT_DISPLAYPORT))
>  		tmp |= AUD_CONFIG_N_VALUE_INDEX;
>  	else
>  		tmp |= audio_config_hdmi_pixel_clock(mode);
> +
> +	tmp &= ~AUD_CONFIG_N_PROG_ENABLE;
> +	if (audio_rate_need_prog(intel_crtc, mode)) {
> +		if (!acomp)
> +			rate = 0;
> +		else if (port >= PORT_A && port <= PORT_E)
> +			rate = acomp->aud_sample_rate[port];
> +		else {
> +			DRM_ERROR("invalid port: %d\n", port);
> +			rate = 0;
> +		}
> +		n = audio_config_get_n(mode, rate);
> +		if (n != 0)
> +			tmp = audio_config_setup_n_reg(n, tmp);
> +		else
> +			DRM_DEBUG_KMS("no suitable N value is found\n");
> +	}
> +
>  	I915_WRITE(HSW_AUD_CFG(pipe), tmp);
>  
>  	mutex_unlock(&dev_priv->av_mutex);
> @@ -594,9 +630,10 @@ static int i915_audio_component_sync_audio_rate(struct device *dev,
>  	struct intel_digital_port *intel_dig_port;
>  	struct intel_crtc *crtc;
>  	struct drm_display_mode *mode;
> +	struct i915_audio_component *acomp = dev_priv->audio_component;
>  	enum pipe pipe = -1;
>  	u32 tmp;
> -	int n_low, n_up, n;
> +	int n;
>  
>  	/* HSW, BDW SKL need this fix */
>  	if (!IS_SKYLAKE(dev_priv) &&
> @@ -630,6 +667,9 @@ static int i915_audio_component_sync_audio_rate(struct device *dev,
>  				  pipe_name(pipe), port_name(port));
>  	mode = &crtc->config->base.adjusted_mode;
>  
> +	/* port must be valid now, otherwise the pipe will be invalid */
> +	acomp->aud_sample_rate[port] = rate;
> +
>  	/* 2. check whether to set the N/CTS/M manually or not */
>  	if (!audio_rate_need_prog(crtc, mode)) {
>  		tmp = I915_READ(HSW_AUD_CFG(pipe));
> @@ -649,15 +689,10 @@ static int i915_audio_component_sync_audio_rate(struct device *dev,
>  		mutex_unlock(&dev_priv->av_mutex);
>  		return 0;
>  	}
> -	n_low = n & 0xfff;
> -	n_up = (n >> 12) & 0xff;
>  
> -	/* 4. set the N/CTS/M */
> +	/* 3. set the N/CTS/M */
>  	tmp = I915_READ(HSW_AUD_CFG(pipe));
> -	tmp &= ~(AUD_CONFIG_UPPER_N_MASK | AUD_CONFIG_LOWER_N_MASK);
> -	tmp |= ((n_up << AUD_CONFIG_UPPER_N_SHIFT) |
> -			(n_low << AUD_CONFIG_LOWER_N_SHIFT) |
> -			AUD_CONFIG_N_PROG_ENABLE);
> +	tmp = audio_config_setup_n_reg(n, tmp);
>  	I915_WRITE(HSW_AUD_CFG(pipe), tmp);
>  
>  	mutex_unlock(&dev_priv->av_mutex);
> @@ -678,6 +713,7 @@ static int i915_audio_component_bind(struct device *i915_dev,
>  {
>  	struct i915_audio_component *acomp = data;
>  	struct drm_i915_private *dev_priv = dev_to_i915(i915_dev);
> +	int i;
>  
>  	if (WARN_ON(acomp->ops || acomp->dev))
>  		return -EEXIST;
> @@ -685,6 +721,9 @@ static int i915_audio_component_bind(struct device *i915_dev,
>  	drm_modeset_lock_all(dev_priv->dev);
>  	acomp->ops = &i915_audio_component_ops;
>  	acomp->dev = i915_dev;
> +	BUILD_BUG_ON(MAX_PORTS != I915_MAX_PORTS);
> +	for (i = 0; i < ARRAY_SIZE(acomp->aud_sample_rate); i++)
> +		acomp->aud_sample_rate[i] = 0;
>  	dev_priv->audio_component = acomp;
>  	drm_modeset_unlock_all(dev_priv->dev);
>  
> diff --git a/include/drm/i915_component.h b/include/drm/i915_component.h
> index e6d35d7..89dc7d6 100644
> --- a/include/drm/i915_component.h
> +++ b/include/drm/i915_component.h
> @@ -24,8 +24,18 @@
>  #ifndef _I915_COMPONENT_H_
>  #define _I915_COMPONENT_H_
>  
> +/* MAX_PORT is the number of port
> + * It must be sync with I915_MAX_PORTS defined i915_drv.h
> + * 5 should be enough as only HSW, BDW, SKL need such fix.
> + */
> +#define MAX_PORTS 5
> +
>  struct i915_audio_component {
>  	struct device *dev;
> +	/**
> +	 * @aud_sample_rate: the array of audio sample rate per port
> +	 */
> +	int aud_sample_rate[MAX_PORTS];
>  
>  	const struct i915_audio_component_ops {
>  		struct module *owner;
> -- 
> 1.9.1
>
Takashi Iwai Sept. 25, 2015, 8:11 a.m. UTC | #2
On Fri, 25 Sep 2015 10:01:48 +0200,
Jani Nikula wrote:
> 
> On Fri, 25 Sep 2015, libin.yang@intel.com wrote:
> > From: Libin Yang <libin.yang@intel.com>
> >
> > When modeset occurs and the TMDS frequency is set to some
> > speical values, the N/CTS need to be set manually if audio
> > is playing.
> >
> > Signed-off-by: Libin Yang <libin.yang@intel.com>
> 
> Reviewed-by: Jani Nikula <jani.nikula@intel.com>

Now all 4 patches are applied to topic/drm-sync-audio-rate.
  git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git topic/drm-sync-audio-rate

It was merged back to sound for-next branch, too.

Feel free to merge this branch into drm tree.


thanks,

Takashi

> 
> 
> > ---
> >  drivers/gpu/drm/i915/intel_audio.c | 57 ++++++++++++++++++++++++++++++++------
> >  include/drm/i915_component.h       | 10 +++++++
> >  2 files changed, 58 insertions(+), 9 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/intel_audio.c b/drivers/gpu/drm/i915/intel_audio.c
> > index e3c32ce..642dfbd 100644
> > --- a/drivers/gpu/drm/i915/intel_audio.c
> > +++ b/drivers/gpu/drm/i915/intel_audio.c
> > @@ -128,6 +128,20 @@ static int audio_config_get_n(const struct drm_display_mode *mode, int rate)
> >  	return 0;
> >  }
> >  
> > +static uint32_t audio_config_setup_n_reg(int n, uint32_t val)
> > +{
> > +	int n_low, n_up;
> > +	uint32_t tmp = val;
> > +
> > +	n_low = n & 0xfff;
> > +	n_up = (n >> 12) & 0xff;
> > +	tmp &= ~(AUD_CONFIG_UPPER_N_MASK | AUD_CONFIG_LOWER_N_MASK);
> > +	tmp |= ((n_up << AUD_CONFIG_UPPER_N_SHIFT) |
> > +			(n_low << AUD_CONFIG_LOWER_N_SHIFT) |
> > +			AUD_CONFIG_N_PROG_ENABLE);
> > +	return tmp;
> > +}
> > +
> >  /* check whether N/CTS/M need be set manually */
> >  static bool audio_rate_need_prog(struct intel_crtc *crtc,
> >  					struct drm_display_mode *mode)
> > @@ -262,9 +276,14 @@ static void hsw_audio_codec_enable(struct drm_connector *connector,
> >  	struct drm_i915_private *dev_priv = connector->dev->dev_private;
> >  	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
> >  	enum pipe pipe = intel_crtc->pipe;
> > +	struct i915_audio_component *acomp = dev_priv->audio_component;
> >  	const uint8_t *eld = connector->eld;
> > +	struct intel_digital_port *intel_dig_port =
> > +		enc_to_dig_port(&encoder->base);
> > +	enum port port = intel_dig_port->port;
> >  	uint32_t tmp;
> >  	int len, i;
> > +	int n, rate;
> >  
> >  	DRM_DEBUG_KMS("Enable audio codec on pipe %c, %u bytes ELD\n",
> >  		      pipe_name(pipe), drm_eld_size(eld));
> > @@ -302,12 +321,29 @@ static void hsw_audio_codec_enable(struct drm_connector *connector,
> >  	/* Enable timestamps */
> >  	tmp = I915_READ(HSW_AUD_CFG(pipe));
> >  	tmp &= ~AUD_CONFIG_N_VALUE_INDEX;
> > -	tmp &= ~AUD_CONFIG_N_PROG_ENABLE;
> >  	tmp &= ~AUD_CONFIG_PIXEL_CLOCK_HDMI_MASK;
> >  	if (intel_pipe_has_type(intel_crtc, INTEL_OUTPUT_DISPLAYPORT))
> >  		tmp |= AUD_CONFIG_N_VALUE_INDEX;
> >  	else
> >  		tmp |= audio_config_hdmi_pixel_clock(mode);
> > +
> > +	tmp &= ~AUD_CONFIG_N_PROG_ENABLE;
> > +	if (audio_rate_need_prog(intel_crtc, mode)) {
> > +		if (!acomp)
> > +			rate = 0;
> > +		else if (port >= PORT_A && port <= PORT_E)
> > +			rate = acomp->aud_sample_rate[port];
> > +		else {
> > +			DRM_ERROR("invalid port: %d\n", port);
> > +			rate = 0;
> > +		}
> > +		n = audio_config_get_n(mode, rate);
> > +		if (n != 0)
> > +			tmp = audio_config_setup_n_reg(n, tmp);
> > +		else
> > +			DRM_DEBUG_KMS("no suitable N value is found\n");
> > +	}
> > +
> >  	I915_WRITE(HSW_AUD_CFG(pipe), tmp);
> >  
> >  	mutex_unlock(&dev_priv->av_mutex);
> > @@ -594,9 +630,10 @@ static int i915_audio_component_sync_audio_rate(struct device *dev,
> >  	struct intel_digital_port *intel_dig_port;
> >  	struct intel_crtc *crtc;
> >  	struct drm_display_mode *mode;
> > +	struct i915_audio_component *acomp = dev_priv->audio_component;
> >  	enum pipe pipe = -1;
> >  	u32 tmp;
> > -	int n_low, n_up, n;
> > +	int n;
> >  
> >  	/* HSW, BDW SKL need this fix */
> >  	if (!IS_SKYLAKE(dev_priv) &&
> > @@ -630,6 +667,9 @@ static int i915_audio_component_sync_audio_rate(struct device *dev,
> >  				  pipe_name(pipe), port_name(port));
> >  	mode = &crtc->config->base.adjusted_mode;
> >  
> > +	/* port must be valid now, otherwise the pipe will be invalid */
> > +	acomp->aud_sample_rate[port] = rate;
> > +
> >  	/* 2. check whether to set the N/CTS/M manually or not */
> >  	if (!audio_rate_need_prog(crtc, mode)) {
> >  		tmp = I915_READ(HSW_AUD_CFG(pipe));
> > @@ -649,15 +689,10 @@ static int i915_audio_component_sync_audio_rate(struct device *dev,
> >  		mutex_unlock(&dev_priv->av_mutex);
> >  		return 0;
> >  	}
> > -	n_low = n & 0xfff;
> > -	n_up = (n >> 12) & 0xff;
> >  
> > -	/* 4. set the N/CTS/M */
> > +	/* 3. set the N/CTS/M */
> >  	tmp = I915_READ(HSW_AUD_CFG(pipe));
> > -	tmp &= ~(AUD_CONFIG_UPPER_N_MASK | AUD_CONFIG_LOWER_N_MASK);
> > -	tmp |= ((n_up << AUD_CONFIG_UPPER_N_SHIFT) |
> > -			(n_low << AUD_CONFIG_LOWER_N_SHIFT) |
> > -			AUD_CONFIG_N_PROG_ENABLE);
> > +	tmp = audio_config_setup_n_reg(n, tmp);
> >  	I915_WRITE(HSW_AUD_CFG(pipe), tmp);
> >  
> >  	mutex_unlock(&dev_priv->av_mutex);
> > @@ -678,6 +713,7 @@ static int i915_audio_component_bind(struct device *i915_dev,
> >  {
> >  	struct i915_audio_component *acomp = data;
> >  	struct drm_i915_private *dev_priv = dev_to_i915(i915_dev);
> > +	int i;
> >  
> >  	if (WARN_ON(acomp->ops || acomp->dev))
> >  		return -EEXIST;
> > @@ -685,6 +721,9 @@ static int i915_audio_component_bind(struct device *i915_dev,
> >  	drm_modeset_lock_all(dev_priv->dev);
> >  	acomp->ops = &i915_audio_component_ops;
> >  	acomp->dev = i915_dev;
> > +	BUILD_BUG_ON(MAX_PORTS != I915_MAX_PORTS);
> > +	for (i = 0; i < ARRAY_SIZE(acomp->aud_sample_rate); i++)
> > +		acomp->aud_sample_rate[i] = 0;
> >  	dev_priv->audio_component = acomp;
> >  	drm_modeset_unlock_all(dev_priv->dev);
> >  
> > diff --git a/include/drm/i915_component.h b/include/drm/i915_component.h
> > index e6d35d7..89dc7d6 100644
> > --- a/include/drm/i915_component.h
> > +++ b/include/drm/i915_component.h
> > @@ -24,8 +24,18 @@
> >  #ifndef _I915_COMPONENT_H_
> >  #define _I915_COMPONENT_H_
> >  
> > +/* MAX_PORT is the number of port
> > + * It must be sync with I915_MAX_PORTS defined i915_drv.h
> > + * 5 should be enough as only HSW, BDW, SKL need such fix.
> > + */
> > +#define MAX_PORTS 5
> > +
> >  struct i915_audio_component {
> >  	struct device *dev;
> > +	/**
> > +	 * @aud_sample_rate: the array of audio sample rate per port
> > +	 */
> > +	int aud_sample_rate[MAX_PORTS];
> >  
> >  	const struct i915_audio_component_ops {
> >  		struct module *owner;
> > -- 
> > 1.9.1
> >
> 
> -- 
> Jani Nikula, Intel Open Source Technology Center
>
Daniel Vetter Oct. 7, 2015, 1:33 p.m. UTC | #3
On Fri, Sep 25, 2015 at 10:11 AM, Takashi Iwai <tiwai@suse.de> wrote:
> On Fri, 25 Sep 2015 10:01:48 +0200,
> Jani Nikula wrote:
>>
>> On Fri, 25 Sep 2015, libin.yang@intel.com wrote:
>> > From: Libin Yang <libin.yang@intel.com>
>> >
>> > When modeset occurs and the TMDS frequency is set to some
>> > speical values, the N/CTS need to be set manually if audio
>> > is playing.
>> >
>> > Signed-off-by: Libin Yang <libin.yang@intel.com>
>>
>> Reviewed-by: Jani Nikula <jani.nikula@intel.com>
>
> Now all 4 patches are applied to topic/drm-sync-audio-rate.
>   git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git topic/drm-sync-audio-rate
>
> It was merged back to sound for-next branch, too.
>
> Feel free to merge this branch into drm tree.

I've merged your branch with now 5 patches into drm-intel-next-queued.
There's a bit of conflicts with ongoing i915 work, so for pull request
ordering it's probably better when sound goes in before drm (or
otherwise Linus will end up with a mess).

Adding Dave about that one as fyi.
-Daniel
diff mbox

Patch

diff --git a/drivers/gpu/drm/i915/intel_audio.c b/drivers/gpu/drm/i915/intel_audio.c
index e3c32ce..642dfbd 100644
--- a/drivers/gpu/drm/i915/intel_audio.c
+++ b/drivers/gpu/drm/i915/intel_audio.c
@@ -128,6 +128,20 @@  static int audio_config_get_n(const struct drm_display_mode *mode, int rate)
 	return 0;
 }
 
+static uint32_t audio_config_setup_n_reg(int n, uint32_t val)
+{
+	int n_low, n_up;
+	uint32_t tmp = val;
+
+	n_low = n & 0xfff;
+	n_up = (n >> 12) & 0xff;
+	tmp &= ~(AUD_CONFIG_UPPER_N_MASK | AUD_CONFIG_LOWER_N_MASK);
+	tmp |= ((n_up << AUD_CONFIG_UPPER_N_SHIFT) |
+			(n_low << AUD_CONFIG_LOWER_N_SHIFT) |
+			AUD_CONFIG_N_PROG_ENABLE);
+	return tmp;
+}
+
 /* check whether N/CTS/M need be set manually */
 static bool audio_rate_need_prog(struct intel_crtc *crtc,
 					struct drm_display_mode *mode)
@@ -262,9 +276,14 @@  static void hsw_audio_codec_enable(struct drm_connector *connector,
 	struct drm_i915_private *dev_priv = connector->dev->dev_private;
 	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
 	enum pipe pipe = intel_crtc->pipe;
+	struct i915_audio_component *acomp = dev_priv->audio_component;
 	const uint8_t *eld = connector->eld;
+	struct intel_digital_port *intel_dig_port =
+		enc_to_dig_port(&encoder->base);
+	enum port port = intel_dig_port->port;
 	uint32_t tmp;
 	int len, i;
+	int n, rate;
 
 	DRM_DEBUG_KMS("Enable audio codec on pipe %c, %u bytes ELD\n",
 		      pipe_name(pipe), drm_eld_size(eld));
@@ -302,12 +321,29 @@  static void hsw_audio_codec_enable(struct drm_connector *connector,
 	/* Enable timestamps */
 	tmp = I915_READ(HSW_AUD_CFG(pipe));
 	tmp &= ~AUD_CONFIG_N_VALUE_INDEX;
-	tmp &= ~AUD_CONFIG_N_PROG_ENABLE;
 	tmp &= ~AUD_CONFIG_PIXEL_CLOCK_HDMI_MASK;
 	if (intel_pipe_has_type(intel_crtc, INTEL_OUTPUT_DISPLAYPORT))
 		tmp |= AUD_CONFIG_N_VALUE_INDEX;
 	else
 		tmp |= audio_config_hdmi_pixel_clock(mode);
+
+	tmp &= ~AUD_CONFIG_N_PROG_ENABLE;
+	if (audio_rate_need_prog(intel_crtc, mode)) {
+		if (!acomp)
+			rate = 0;
+		else if (port >= PORT_A && port <= PORT_E)
+			rate = acomp->aud_sample_rate[port];
+		else {
+			DRM_ERROR("invalid port: %d\n", port);
+			rate = 0;
+		}
+		n = audio_config_get_n(mode, rate);
+		if (n != 0)
+			tmp = audio_config_setup_n_reg(n, tmp);
+		else
+			DRM_DEBUG_KMS("no suitable N value is found\n");
+	}
+
 	I915_WRITE(HSW_AUD_CFG(pipe), tmp);
 
 	mutex_unlock(&dev_priv->av_mutex);
@@ -594,9 +630,10 @@  static int i915_audio_component_sync_audio_rate(struct device *dev,
 	struct intel_digital_port *intel_dig_port;
 	struct intel_crtc *crtc;
 	struct drm_display_mode *mode;
+	struct i915_audio_component *acomp = dev_priv->audio_component;
 	enum pipe pipe = -1;
 	u32 tmp;
-	int n_low, n_up, n;
+	int n;
 
 	/* HSW, BDW SKL need this fix */
 	if (!IS_SKYLAKE(dev_priv) &&
@@ -630,6 +667,9 @@  static int i915_audio_component_sync_audio_rate(struct device *dev,
 				  pipe_name(pipe), port_name(port));
 	mode = &crtc->config->base.adjusted_mode;
 
+	/* port must be valid now, otherwise the pipe will be invalid */
+	acomp->aud_sample_rate[port] = rate;
+
 	/* 2. check whether to set the N/CTS/M manually or not */
 	if (!audio_rate_need_prog(crtc, mode)) {
 		tmp = I915_READ(HSW_AUD_CFG(pipe));
@@ -649,15 +689,10 @@  static int i915_audio_component_sync_audio_rate(struct device *dev,
 		mutex_unlock(&dev_priv->av_mutex);
 		return 0;
 	}
-	n_low = n & 0xfff;
-	n_up = (n >> 12) & 0xff;
 
-	/* 4. set the N/CTS/M */
+	/* 3. set the N/CTS/M */
 	tmp = I915_READ(HSW_AUD_CFG(pipe));
-	tmp &= ~(AUD_CONFIG_UPPER_N_MASK | AUD_CONFIG_LOWER_N_MASK);
-	tmp |= ((n_up << AUD_CONFIG_UPPER_N_SHIFT) |
-			(n_low << AUD_CONFIG_LOWER_N_SHIFT) |
-			AUD_CONFIG_N_PROG_ENABLE);
+	tmp = audio_config_setup_n_reg(n, tmp);
 	I915_WRITE(HSW_AUD_CFG(pipe), tmp);
 
 	mutex_unlock(&dev_priv->av_mutex);
@@ -678,6 +713,7 @@  static int i915_audio_component_bind(struct device *i915_dev,
 {
 	struct i915_audio_component *acomp = data;
 	struct drm_i915_private *dev_priv = dev_to_i915(i915_dev);
+	int i;
 
 	if (WARN_ON(acomp->ops || acomp->dev))
 		return -EEXIST;
@@ -685,6 +721,9 @@  static int i915_audio_component_bind(struct device *i915_dev,
 	drm_modeset_lock_all(dev_priv->dev);
 	acomp->ops = &i915_audio_component_ops;
 	acomp->dev = i915_dev;
+	BUILD_BUG_ON(MAX_PORTS != I915_MAX_PORTS);
+	for (i = 0; i < ARRAY_SIZE(acomp->aud_sample_rate); i++)
+		acomp->aud_sample_rate[i] = 0;
 	dev_priv->audio_component = acomp;
 	drm_modeset_unlock_all(dev_priv->dev);
 
diff --git a/include/drm/i915_component.h b/include/drm/i915_component.h
index e6d35d7..89dc7d6 100644
--- a/include/drm/i915_component.h
+++ b/include/drm/i915_component.h
@@ -24,8 +24,18 @@ 
 #ifndef _I915_COMPONENT_H_
 #define _I915_COMPONENT_H_
 
+/* MAX_PORT is the number of port
+ * It must be sync with I915_MAX_PORTS defined i915_drv.h
+ * 5 should be enough as only HSW, BDW, SKL need such fix.
+ */
+#define MAX_PORTS 5
+
 struct i915_audio_component {
 	struct device *dev;
+	/**
+	 * @aud_sample_rate: the array of audio sample rate per port
+	 */
+	int aud_sample_rate[MAX_PORTS];
 
 	const struct i915_audio_component_ops {
 		struct module *owner;