[v6,10/17] phy: Add driver for rockchip Display Port PHY
diff mbox

Message ID 1444492559-27181-1-git-send-email-ykk@rock-chips.com
State New
Headers show

Commit Message

Yakir Yang Oct. 10, 2015, 3:55 p.m. UTC
This phy driver would control the Rockchip DisplayPort module
phy clock and phy power, it is relate to analogix_dp-rockchip
dp driver. If you want DP works rightly on rockchip platform,
then you should select both of them.

Signed-off-by: Yakir Yang <ykk@rock-chips.com>
---
Changes in v6: None
Changes in v5:
- Remove "reg" DT property, cause driver could poweron/poweroff phy via
  the exist "grf" syscon already. And rename the example DT node from
  "edp_phy: phy@ff770274" to "edp_phy: edp-phy" directly. (Heiko)
- Add deivce_node at the front of driver, update phy_ops type from "static
  struct" to "static const struct". And correct the input paramters of
  devm_phy_create() interfaces. (Heiko)

Changes in v4:
- Add commit message, and remove the redundant rockchip_dp_phy_init()
  function, move those code to probe() method. And remove driver .owner
  number. (Kishon)

Changes in v3:
- Suggest, add rockchip dp phy driver, collect the phy clocks and
  power control. (Heiko)

Changes in v2: None

 drivers/phy/Kconfig           |   7 ++
 drivers/phy/Makefile          |   1 +
 drivers/phy/phy-rockchip-dp.c | 151 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 159 insertions(+)
 create mode 100644 drivers/phy/phy-rockchip-dp.c

Comments

Kishon Vijay Abraham I Oct. 12, 2015, 3:02 p.m. UTC | #1
Hi,

On Saturday 10 October 2015 09:25 PM, Yakir Yang wrote:
> This phy driver would control the Rockchip DisplayPort module
> phy clock and phy power, it is relate to analogix_dp-rockchip
> dp driver. If you want DP works rightly on rockchip platform,
> then you should select both of them.

Add phy driver for the Rockchip DisplayPort PHY module. This is required
to get DisplayPort working in Rockchip SoCs.
> 
> Signed-off-by: Yakir Yang <ykk@rock-chips.com>
> ---
> Changes in v6: None
> Changes in v5:
> - Remove "reg" DT property, cause driver could poweron/poweroff phy via
>   the exist "grf" syscon already. And rename the example DT node from
>   "edp_phy: phy@ff770274" to "edp_phy: edp-phy" directly. (Heiko)
> - Add deivce_node at the front of driver, update phy_ops type from "static
>   struct" to "static const struct". And correct the input paramters of
>   devm_phy_create() interfaces. (Heiko)
> 
> Changes in v4:
> - Add commit message, and remove the redundant rockchip_dp_phy_init()
>   function, move those code to probe() method. And remove driver .owner
>   number. (Kishon)
> 
> Changes in v3:
> - Suggest, add rockchip dp phy driver, collect the phy clocks and
>   power control. (Heiko)
> 
> Changes in v2: None
> 
>  drivers/phy/Kconfig           |   7 ++
>  drivers/phy/Makefile          |   1 +
>  drivers/phy/phy-rockchip-dp.c | 151 ++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 159 insertions(+)
>  create mode 100644 drivers/phy/phy-rockchip-dp.c
> 
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 47da573..8f2bc4f 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -310,6 +310,13 @@ config PHY_ROCKCHIP_USB
>  	help
>  	  Enable this to support the Rockchip USB 2.0 PHY.
>  
> +config PHY_ROCKCHIP_DP
> +	tristate "Rockchip Display Port PHY Driver"
> +	depends on ARCH_ROCKCHIP && OF
> +	select GENERIC_PHY
> +	help
> +	  Enable this to support the Rockchip Display Port PHY.
> +
>  config PHY_ST_SPEAR1310_MIPHY
>  	tristate "ST SPEAR1310-MIPHY driver"
>  	select GENERIC_PHY
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index a5b18c1..e281f35 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -34,6 +34,7 @@ phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
>  obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
>  obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
>  obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
> +obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
>  obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
>  obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
>  obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
> diff --git a/drivers/phy/phy-rockchip-dp.c b/drivers/phy/phy-rockchip-dp.c
> new file mode 100644
> index 0000000..3a2ac120
> --- /dev/null
> +++ b/drivers/phy/phy-rockchip-dp.c
> @@ -0,0 +1,151 @@
> +/*
> + * Rockchip DP PHY driver
> + *
> + * Copyright (C) 2015 FuZhou Rockchip Co., Ltd.
> + * Author: Yakir Yang <ykk@@rock-chips.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License.
> + */
> +
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/clk.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regmap.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/platform_device.h>
> +
> +#define GRF_SOC_CON12                   0x0274
> +#define GRF_EDP_REF_CLK_SEL_INTER	BIT(4)
> +#define GRF_EDP_PHY_SIDDQ_WRITE_EN      BIT(21)
> +#define GRF_EDP_PHY_SIDDQ_ON            0
> +#define GRF_EDP_PHY_SIDDQ_OFF           BIT(5)
> +
> +struct rockchip_dp_phy {
> +	struct device  *dev;
> +	struct regmap  *grf;
> +	struct clk     *phy_24m;
> +};
> +
> +static int rockchip_set_phy_state(struct phy *phy, bool enable)
> +{
> +	struct rockchip_dp_phy *dp = phy_get_drvdata(phy);
> +	int ret;
> +
> +	if (enable) {
> +		ret = clk_prepare_enable(dp->phy_24m);
> +		if (ret < 0) {
> +			dev_err(dp->dev, "Can't enable clock 24m %d\n", ret);
> +			return ret;
> +		}
> +
> +		ret = regmap_write(dp->grf, GRF_SOC_CON12,
> +				   GRF_EDP_PHY_SIDDQ_WRITE_EN |
> +				   GRF_EDP_PHY_SIDDQ_ON);
> +	} else {
> +		clk_disable_unprepare(dp->phy_24m);

should clk_disable come after regmap_write? It'll be symmetric to enable?
> +		ret = regmap_write(dp->grf, GRF_SOC_CON12,
> +				   GRF_EDP_PHY_SIDDQ_WRITE_EN |
> +				   GRF_EDP_PHY_SIDDQ_OFF);

Is this syscon register used only by Display Port PHY? Better to use
regmap_update API?

Thanks
Kishon
Heiko Stuebner Oct. 12, 2015, 4:18 p.m. UTC | #2
Am Montag, 12. Oktober 2015, 20:32:47 schrieb Kishon Vijay Abraham I:
> Hi,
> 
> On Saturday 10 October 2015 09:25 PM, Yakir Yang wrote:
> > This phy driver would control the Rockchip DisplayPort module
> > phy clock and phy power, it is relate to analogix_dp-rockchip
> > dp driver. If you want DP works rightly on rockchip platform,
> > then you should select both of them.
> 
> Add phy driver for the Rockchip DisplayPort PHY module. This is required
> to get DisplayPort working in Rockchip SoCs.
> 
> > Signed-off-by: Yakir Yang <ykk@rock-chips.com>
> > ---
> > Changes in v6: None
> > Changes in v5:
> > - Remove "reg" DT property, cause driver could poweron/poweroff phy via
> > 
> >   the exist "grf" syscon already. And rename the example DT node from
> >   "edp_phy: phy@ff770274" to "edp_phy: edp-phy" directly. (Heiko)
> > 
> > - Add deivce_node at the front of driver, update phy_ops type from "static
> > 
> >   struct" to "static const struct". And correct the input paramters of
> >   devm_phy_create() interfaces. (Heiko)
> > 
> > Changes in v4:
> > - Add commit message, and remove the redundant rockchip_dp_phy_init()
> > 
> >   function, move those code to probe() method. And remove driver .owner
> >   number. (Kishon)
> > 
> > Changes in v3:
> > - Suggest, add rockchip dp phy driver, collect the phy clocks and
> > 
> >   power control. (Heiko)
> > 
> > Changes in v2: None
> > 
> >  drivers/phy/Kconfig           |   7 ++
> >  drivers/phy/Makefile          |   1 +
> >  drivers/phy/phy-rockchip-dp.c | 151
> >  ++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 159
> >  insertions(+)
> >  create mode 100644 drivers/phy/phy-rockchip-dp.c
> > 
> > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> > index 47da573..8f2bc4f 100644
> > --- a/drivers/phy/Kconfig
> > +++ b/drivers/phy/Kconfig
> > @@ -310,6 +310,13 @@ config PHY_ROCKCHIP_USB
> > 
> >  	help
> >  	
> >  	  Enable this to support the Rockchip USB 2.0 PHY.
> > 
> > +config PHY_ROCKCHIP_DP
> > +	tristate "Rockchip Display Port PHY Driver"
> > +	depends on ARCH_ROCKCHIP && OF
> > +	select GENERIC_PHY
> > +	help
> > +	  Enable this to support the Rockchip Display Port PHY.
> > +
> > 
> >  config PHY_ST_SPEAR1310_MIPHY
> >  
> >  	tristate "ST SPEAR1310-MIPHY driver"
> >  	select GENERIC_PHY
> > 
> > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> > index a5b18c1..e281f35 100644
> > --- a/drivers/phy/Makefile
> > +++ b/drivers/phy/Makefile
> > @@ -34,6 +34,7 @@ phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+=
> > phy-s5pv210-usb2.o> 
> >  obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
> >  obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
> >  obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
> > 
> > +obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
> > 
> >  obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
> >  obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
> >  obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
> > 
> > diff --git a/drivers/phy/phy-rockchip-dp.c b/drivers/phy/phy-rockchip-dp.c
> > new file mode 100644
> > index 0000000..3a2ac120
> > --- /dev/null
> > +++ b/drivers/phy/phy-rockchip-dp.c
> > @@ -0,0 +1,151 @@
> > +/*
> > + * Rockchip DP PHY driver
> > + *
> > + * Copyright (C) 2015 FuZhou Rockchip Co., Ltd.
> > + * Author: Yakir Yang <ykk@@rock-chips.com>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License.
> > + */
> > +
> > +#include <linux/io.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_address.h>
> > +#include <linux/clk.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/regmap.h>
> > +#include <linux/mfd/syscon.h>
> > +#include <linux/platform_device.h>
> > +
> > +#define GRF_SOC_CON12                   0x0274
> > +#define GRF_EDP_REF_CLK_SEL_INTER	BIT(4)
> > +#define GRF_EDP_PHY_SIDDQ_WRITE_EN      BIT(21)
> > +#define GRF_EDP_PHY_SIDDQ_ON            0
> > +#define GRF_EDP_PHY_SIDDQ_OFF           BIT(5)
> > +
> > +struct rockchip_dp_phy {
> > +	struct device  *dev;
> > +	struct regmap  *grf;
> > +	struct clk     *phy_24m;
> > +};
> > +
> > +static int rockchip_set_phy_state(struct phy *phy, bool enable)
> > +{
> > +	struct rockchip_dp_phy *dp = phy_get_drvdata(phy);
> > +	int ret;
> > +
> > +	if (enable) {
> > +		ret = clk_prepare_enable(dp->phy_24m);
> > +		if (ret < 0) {
> > +			dev_err(dp->dev, "Can't enable clock 24m %d\n", ret);
> > +			return ret;
> > +		}
> > +
> > +		ret = regmap_write(dp->grf, GRF_SOC_CON12,
> > +				   GRF_EDP_PHY_SIDDQ_WRITE_EN |
> > +				   GRF_EDP_PHY_SIDDQ_ON);
> > +	} else {
> > +		clk_disable_unprepare(dp->phy_24m);
> 
> should clk_disable come after regmap_write? It'll be symmetric to enable?
> 
> > +		ret = regmap_write(dp->grf, GRF_SOC_CON12,
> > +				   GRF_EDP_PHY_SIDDQ_WRITE_EN |
> > +				   GRF_EDP_PHY_SIDDQ_OFF);
> 
> Is this syscon register used only by Display Port PHY? Better to use
> regmap_update API?

Rockchip's GRF syscon registers use what gets called "Hiword-mask", so when 
writing you actually need to set the write-enable bit (x+16, like 
GRF_EDP_PHY_SIDDQ_WRITE_EN here) if you want to set bit x. No other bits get 
affected by this.


Heiko
Yakir Yang Oct. 13, 2015, 1:20 a.m. UTC | #3
Hi Kishon

On 10/12/2015 11:02 PM, Kishon Vijay Abraham I wrote:
> Hi,
>
> On Saturday 10 October 2015 09:25 PM, Yakir Yang wrote:
>> This phy driver would control the Rockchip DisplayPort module
>> phy clock and phy power, it is relate to analogix_dp-rockchip
>> dp driver. If you want DP works rightly on rockchip platform,
>> then you should select both of them.
> Add phy driver for the Rockchip DisplayPort PHY module. This is required
> to get DisplayPort working in Rockchip SoCs.

Thanks, take point.

>> Signed-off-by: Yakir Yang <ykk@rock-chips.com>
>> ---
>> Changes in v6: None
>> Changes in v5:
>> - Remove "reg" DT property, cause driver could poweron/poweroff phy via
>>    the exist "grf" syscon already. And rename the example DT node from
>>    "edp_phy: phy@ff770274" to "edp_phy: edp-phy" directly. (Heiko)
>> - Add deivce_node at the front of driver, update phy_ops type from "static
>>    struct" to "static const struct". And correct the input paramters of
>>    devm_phy_create() interfaces. (Heiko)
>>
>> Changes in v4:
>> - Add commit message, and remove the redundant rockchip_dp_phy_init()
>>    function, move those code to probe() method. And remove driver .owner
>>    number. (Kishon)
>>
>> Changes in v3:
>> - Suggest, add rockchip dp phy driver, collect the phy clocks and
>>    power control. (Heiko)
>>
>> Changes in v2: None
>>
>>   drivers/phy/Kconfig           |   7 ++
>>   drivers/phy/Makefile          |   1 +
>>   drivers/phy/phy-rockchip-dp.c | 151 ++++++++++++++++++++++++++++++++++++++++++
>>   3 files changed, 159 insertions(+)
>>   create mode 100644 drivers/phy/phy-rockchip-dp.c
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index 47da573..8f2bc4f 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -310,6 +310,13 @@ config PHY_ROCKCHIP_USB
>>   	help
>>   	  Enable this to support the Rockchip USB 2.0 PHY.
>>   
>> +config PHY_ROCKCHIP_DP
>> +	tristate "Rockchip Display Port PHY Driver"
>> +	depends on ARCH_ROCKCHIP && OF
>> +	select GENERIC_PHY
>> +	help
>> +	  Enable this to support the Rockchip Display Port PHY.
>> +
>>   config PHY_ST_SPEAR1310_MIPHY
>>   	tristate "ST SPEAR1310-MIPHY driver"
>>   	select GENERIC_PHY
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index a5b18c1..e281f35 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -34,6 +34,7 @@ phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
>>   obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
>>   obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
>>   obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
>> +obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
>>   obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
>>   obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
>>   obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
>> diff --git a/drivers/phy/phy-rockchip-dp.c b/drivers/phy/phy-rockchip-dp.c
>> new file mode 100644
>> index 0000000..3a2ac120
>> --- /dev/null
>> +++ b/drivers/phy/phy-rockchip-dp.c
>> @@ -0,0 +1,151 @@
>> +/*
>> + * Rockchip DP PHY driver
>> + *
>> + * Copyright (C) 2015 FuZhou Rockchip Co., Ltd.
>> + * Author: Yakir Yang <ykk@@rock-chips.com>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License.
>> + */
>> +
>> +#include <linux/io.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/clk.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/regmap.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/platform_device.h>
>> +
>> +#define GRF_SOC_CON12                   0x0274
>> +#define GRF_EDP_REF_CLK_SEL_INTER	BIT(4)
>> +#define GRF_EDP_PHY_SIDDQ_WRITE_EN      BIT(21)
>> +#define GRF_EDP_PHY_SIDDQ_ON            0
>> +#define GRF_EDP_PHY_SIDDQ_OFF           BIT(5)
>> +
>> +struct rockchip_dp_phy {
>> +	struct device  *dev;
>> +	struct regmap  *grf;
>> +	struct clk     *phy_24m;
>> +};
>> +
>> +static int rockchip_set_phy_state(struct phy *phy, bool enable)
>> +{
>> +	struct rockchip_dp_phy *dp = phy_get_drvdata(phy);
>> +	int ret;
>> +
>> +	if (enable) {
>> +		ret = clk_prepare_enable(dp->phy_24m);
>> +		if (ret < 0) {
>> +			dev_err(dp->dev, "Can't enable clock 24m %d\n", ret);
>> +			return ret;
>> +		}
>> +
>> +		ret = regmap_write(dp->grf, GRF_SOC_CON12,
>> +				   GRF_EDP_PHY_SIDDQ_WRITE_EN |
>> +				   GRF_EDP_PHY_SIDDQ_ON);
>> +	} else {
>> +		clk_disable_unprepare(dp->phy_24m);
> should clk_disable come after regmap_write? It'll be symmetric to enable?

I don't see there is a strict limit about this, but thanks for your point, I
would like to change this order to:

     if (enable) {
         // Enable SIDDQ power
         // Enable Clock
     } else {
         // Disable Clock
         // Disable SIDDQ power
     }

>> +		ret = regmap_write(dp->grf, GRF_SOC_CON12,
>> +				   GRF_EDP_PHY_SIDDQ_WRITE_EN |
>> +				   GRF_EDP_PHY_SIDDQ_OFF);
> Is this syscon register used only by Display Port PHY? Better to use
> regmap_update API?

Thanks to Heiko explain, writing you actually need to set the
write-enable bit, some kind of hardware regmap_update.


Thanks,
- Yakir

> Thanks
> Kishon
>
>
>

Patch
diff mbox

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 47da573..8f2bc4f 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -310,6 +310,13 @@  config PHY_ROCKCHIP_USB
 	help
 	  Enable this to support the Rockchip USB 2.0 PHY.
 
+config PHY_ROCKCHIP_DP
+	tristate "Rockchip Display Port PHY Driver"
+	depends on ARCH_ROCKCHIP && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the Rockchip Display Port PHY.
+
 config PHY_ST_SPEAR1310_MIPHY
 	tristate "ST SPEAR1310-MIPHY driver"
 	select GENERIC_PHY
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index a5b18c1..e281f35 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -34,6 +34,7 @@  phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
 obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
 obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
 obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
+obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
 obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
 obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
 obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
diff --git a/drivers/phy/phy-rockchip-dp.c b/drivers/phy/phy-rockchip-dp.c
new file mode 100644
index 0000000..3a2ac120
--- /dev/null
+++ b/drivers/phy/phy-rockchip-dp.c
@@ -0,0 +1,151 @@ 
+/*
+ * Rockchip DP PHY driver
+ *
+ * Copyright (C) 2015 FuZhou Rockchip Co., Ltd.
+ * Author: Yakir Yang <ykk@@rock-chips.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/clk.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+#include <linux/platform_device.h>
+
+#define GRF_SOC_CON12                   0x0274
+#define GRF_EDP_REF_CLK_SEL_INTER	BIT(4)
+#define GRF_EDP_PHY_SIDDQ_WRITE_EN      BIT(21)
+#define GRF_EDP_PHY_SIDDQ_ON            0
+#define GRF_EDP_PHY_SIDDQ_OFF           BIT(5)
+
+struct rockchip_dp_phy {
+	struct device  *dev;
+	struct regmap  *grf;
+	struct clk     *phy_24m;
+};
+
+static int rockchip_set_phy_state(struct phy *phy, bool enable)
+{
+	struct rockchip_dp_phy *dp = phy_get_drvdata(phy);
+	int ret;
+
+	if (enable) {
+		ret = clk_prepare_enable(dp->phy_24m);
+		if (ret < 0) {
+			dev_err(dp->dev, "Can't enable clock 24m %d\n", ret);
+			return ret;
+		}
+
+		ret = regmap_write(dp->grf, GRF_SOC_CON12,
+				   GRF_EDP_PHY_SIDDQ_WRITE_EN |
+				   GRF_EDP_PHY_SIDDQ_ON);
+	} else {
+		clk_disable_unprepare(dp->phy_24m);
+		ret = regmap_write(dp->grf, GRF_SOC_CON12,
+				   GRF_EDP_PHY_SIDDQ_WRITE_EN |
+				   GRF_EDP_PHY_SIDDQ_OFF);
+	}
+
+	return ret;
+}
+
+static int rockchip_dp_phy_power_on(struct phy *phy)
+{
+	return rockchip_set_phy_state(phy, true);
+}
+
+static int rockchip_dp_phy_power_off(struct phy *phy)
+{
+	return rockchip_set_phy_state(phy, false);
+}
+
+static const struct phy_ops rockchip_dp_phy_ops = {
+	.power_on	= rockchip_dp_phy_power_on,
+	.power_off	= rockchip_dp_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int rockchip_dp_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct phy_provider *phy_provider;
+	struct rockchip_dp_phy *dp;
+	struct resource *res;
+	struct phy *phy;
+	int ret;
+
+	if (!np)
+		return -ENODEV;
+
+	dp = devm_kzalloc(dev, sizeof(*dp), GFP_KERNEL);
+	if (IS_ERR(dp))
+		return -ENOMEM;
+
+	dp->dev = dev;
+
+	dp->phy_24m = devm_clk_get(dev, "24m");
+	if (IS_ERR(dp->phy_24m)) {
+		dev_err(dev, "cannot get clock 24m\n");
+		return PTR_ERR(dp->phy_24m);
+	}
+
+	ret = clk_set_rate(dp->phy_24m, 24000000);
+	if (ret < 0) {
+		dev_err(dp->dev, "cannot set clock phy_24m %d\n", ret);
+		return ret;
+	}
+
+	dp->grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf");
+	if (IS_ERR(dp->grf)) {
+		dev_err(dev, "rk3288-dp needs rockchip,grf property\n");
+		return PTR_ERR(dp->grf);
+	}
+
+	ret = regmap_write(dp->grf, GRF_SOC_CON12, GRF_EDP_REF_CLK_SEL_INTER |
+			   (GRF_EDP_REF_CLK_SEL_INTER << 16));
+	if (ret != 0) {
+		dev_err(dp->dev, "Could not config GRF edp ref clk: %d\n", ret);
+		return ret;
+	}
+
+	phy = devm_phy_create(dev, np, &rockchip_dp_phy_ops);
+	if (IS_ERR(phy)) {
+		dev_err(dev, "failed to create phy\n");
+		return PTR_ERR(phy);
+	}
+	phy_set_drvdata(phy, dp);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id rockchip_dp_phy_dt_ids[] = {
+	{ .compatible = "rockchip,rk3288-dp-phy" },
+	{}
+};
+
+MODULE_DEVICE_TABLE(of, rockchip_dp_phy_dt_ids);
+
+static struct platform_driver rockchip_dp_phy_driver = {
+	.probe		= rockchip_dp_phy_probe,
+	.driver		= {
+		.name	= "rockchip-dp-phy",
+		.of_match_table = rockchip_dp_phy_dt_ids,
+	},
+};
+
+module_platform_driver(rockchip_dp_phy_driver);
+
+MODULE_AUTHOR("Yakir Yang <ykk@rock-chips.com>");
+MODULE_DESCRIPTION("Rockchip DP PHY driver");
+MODULE_LICENSE("GPL v2");