@@ -490,6 +490,15 @@ static inline void iwl_enable_interrupts(struct iwl_trans *trans)
iwl_write32(trans, CSR_INT_MASK, trans_pcie->inta_mask);
}
+static inline void iwl_enable_fw_load_int(struct iwl_trans *trans)
+{
+ struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
+
+ IWL_DEBUG_ISR(trans, "Enabling FW load interrupt\n");
+ trans_pcie->inta_mask = CSR_INT_BIT_FH_TX;
+ iwl_write32(trans, CSR_INT_MASK, trans_pcie->inta_mask);
+}
+
static inline void iwl_enable_rfkill_int(struct iwl_trans *trans)
{
struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
@@ -1438,9 +1438,11 @@ irqreturn_t iwl_pcie_irq_handler(int irq, void *dev_id)
inta & ~trans_pcie->inta_mask);
}
- /* Re-enable all interrupts */
- /* only Re-enable if disabled by irq */
- if (test_bit(STATUS_INT_ENABLED, &trans->status))
+ /* we are loading the firmware, enable FH_TX interrupt only */
+ if (handled & CSR_INT_BIT_FH_TX)
+ iwl_enable_fw_load_int(trans);
+ /* only Re-enable all interrupt if disabled by irq */
+ else if (test_bit(STATUS_INT_ENABLED, &trans->status))
iwl_enable_interrupts(trans);
/* Re-enable RF_KILL if it occurred */
else if (handled & CSR_INT_BIT_RF_KILL)
@@ -1021,82 +1021,6 @@ static int iwl_pcie_load_given_ucode_8000(struct iwl_trans *trans,
&first_ucode_section);
}
-static int iwl_trans_pcie_start_fw(struct iwl_trans *trans,
- const struct fw_img *fw, bool run_in_rfkill)
-{
- struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
- bool hw_rfkill;
- int ret;
-
- mutex_lock(&trans_pcie->mutex);
-
- /* Someone called stop_device, don't try to start_fw */
- if (trans_pcie->is_down) {
- IWL_WARN(trans,
- "Can't start_fw since the HW hasn't been started\n");
- ret = EIO;
- goto out;
- }
-
- /* This may fail if AMT took ownership of the device */
- if (iwl_pcie_prepare_card_hw(trans)) {
- IWL_WARN(trans, "Exit HW not ready\n");
- ret = -EIO;
- goto out;
- }
-
- iwl_enable_rfkill_int(trans);
-
- /* If platform's RF_KILL switch is NOT set to KILL */
- hw_rfkill = iwl_is_rfkill_set(trans);
- if (hw_rfkill)
- set_bit(STATUS_RFKILL, &trans->status);
- else
- clear_bit(STATUS_RFKILL, &trans->status);
- iwl_trans_pcie_rf_kill(trans, hw_rfkill);
- if (hw_rfkill && !run_in_rfkill) {
- ret = -ERFKILL;
- goto out;
- }
-
- iwl_write32(trans, CSR_INT, 0xFFFFFFFF);
-
- ret = iwl_pcie_nic_init(trans);
- if (ret) {
- IWL_ERR(trans, "Unable to init nic\n");
- goto out;
- }
-
- /* make sure rfkill handshake bits are cleared */
- iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
- iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR,
- CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
-
- /* clear (again), then enable host interrupts */
- iwl_write32(trans, CSR_INT, 0xFFFFFFFF);
- iwl_enable_interrupts(trans);
-
- /* really make sure rfkill handshake bits are cleared */
- iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
- iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
-
- /* Load the given image to the HW */
- if (trans->cfg->device_family == IWL_DEVICE_FAMILY_8000)
- ret = iwl_pcie_load_given_ucode_8000(trans, fw);
- else
- ret = iwl_pcie_load_given_ucode(trans, fw);
-
-out:
- mutex_unlock(&trans_pcie->mutex);
- return ret;
-}
-
-static void iwl_trans_pcie_fw_alive(struct iwl_trans *trans, u32 scd_addr)
-{
- iwl_pcie_reset_ict(trans);
- iwl_pcie_tx_start(trans, scd_addr);
-}
-
static void _iwl_trans_pcie_stop_device(struct iwl_trans *trans, bool low_power)
{
struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
@@ -1127,7 +1051,8 @@ static void _iwl_trans_pcie_stop_device(struct iwl_trans *trans, bool low_power)
* already dead.
*/
if (test_and_clear_bit(STATUS_DEVICE_ENABLED, &trans->status)) {
- IWL_DEBUG_INFO(trans, "DEVICE_ENABLED bit was set and is now cleared\n");
+ IWL_DEBUG_INFO(trans,
+ "DEVICE_ENABLED bit was set and is now cleared\n");
iwl_pcie_tx_stop(trans);
iwl_pcie_rx_stop(trans);
@@ -1161,7 +1086,6 @@ static void _iwl_trans_pcie_stop_device(struct iwl_trans *trans, bool low_power)
iwl_disable_interrupts(trans);
spin_unlock(&trans_pcie->irq_lock);
-
/* clear all status bits */
clear_bit(STATUS_SYNC_HCMD_ACTIVE, &trans->status);
clear_bit(STATUS_INT_ENABLED, &trans->status);
@@ -1194,10 +1118,116 @@ static void _iwl_trans_pcie_stop_device(struct iwl_trans *trans, bool low_power)
if (hw_rfkill != was_hw_rfkill)
iwl_trans_pcie_rf_kill(trans, hw_rfkill);
- /* re-take ownership to prevent other users from stealing the deivce */
+ /* re-take ownership to prevent other users from stealing the device */
iwl_pcie_prepare_card_hw(trans);
}
+static int iwl_trans_pcie_start_fw(struct iwl_trans *trans,
+ const struct fw_img *fw, bool run_in_rfkill)
+{
+ struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
+ bool hw_rfkill;
+ int ret;
+
+ /* This may fail if AMT took ownership of the device */
+ if (iwl_pcie_prepare_card_hw(trans)) {
+ IWL_WARN(trans, "Exit HW not ready\n");
+ ret = -EIO;
+ goto out;
+ }
+
+ iwl_enable_rfkill_int(trans);
+
+ iwl_write32(trans, CSR_INT, 0xFFFFFFFF);
+
+ /*
+ * We enabled the RF-Kill interrupt and the handler may very
+ * well be running. Disable the interrupts to make sure no other
+ * interrupt can be fired.
+ */
+ iwl_disable_interrupts(trans);
+
+ /* Make sure it finished running */
+ synchronize_irq(trans_pcie->pci_dev->irq);
+
+ mutex_lock(&trans_pcie->mutex);
+
+ /* If platform's RF_KILL switch is NOT set to KILL */
+ hw_rfkill = iwl_is_rfkill_set(trans);
+ if (hw_rfkill)
+ set_bit(STATUS_RFKILL, &trans->status);
+ else
+ clear_bit(STATUS_RFKILL, &trans->status);
+ iwl_trans_pcie_rf_kill(trans, hw_rfkill);
+ if (hw_rfkill && !run_in_rfkill) {
+ ret = -ERFKILL;
+ goto out;
+ }
+
+ /* Someone called stop_device, don't try to start_fw */
+ if (trans_pcie->is_down) {
+ IWL_WARN(trans,
+ "Can't start_fw since the HW hasn't been started\n");
+ ret = EIO;
+ goto out;
+ }
+
+ /* make sure rfkill handshake bits are cleared */
+ iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
+ iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR,
+ CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED);
+
+ /* clear (again), then enable host interrupts */
+ iwl_write32(trans, CSR_INT, 0xFFFFFFFF);
+
+ ret = iwl_pcie_nic_init(trans);
+ if (ret) {
+ IWL_ERR(trans, "Unable to init nic\n");
+ goto out;
+ }
+
+ /*
+ * Now, we load the firmware and don't want to be interrupted, even
+ * by the RF-Kill interrupt (hence mask all the interrupt besides the
+ * FH_TX interrupt which is needed to load the firmware). If the
+ * RF-Kill switch is toggled, we will find out after having loaded
+ * the firmware and return the proper value to the caller.
+ */
+ iwl_enable_fw_load_int(trans);
+
+ /* really make sure rfkill handshake bits are cleared */
+ iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
+ iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL);
+
+ /* Load the given image to the HW */
+ if (trans->cfg->device_family == IWL_DEVICE_FAMILY_8000)
+ ret = iwl_pcie_load_given_ucode_8000(trans, fw);
+ else
+ ret = iwl_pcie_load_given_ucode(trans, fw);
+ iwl_enable_interrupts(trans);
+
+ /* re-check RF-Kill state since we may have missed the interrupt */
+ hw_rfkill = iwl_is_rfkill_set(trans);
+ if (hw_rfkill)
+ set_bit(STATUS_RFKILL, &trans->status);
+ else
+ clear_bit(STATUS_RFKILL, &trans->status);
+
+ iwl_trans_pcie_rf_kill(trans, hw_rfkill);
+ if (hw_rfkill && !run_in_rfkill)
+ ret = -ERFKILL;
+
+out:
+ mutex_unlock(&trans_pcie->mutex);
+ return ret;
+}
+
+static void iwl_trans_pcie_fw_alive(struct iwl_trans *trans, u32 scd_addr)
+{
+ iwl_pcie_reset_ict(trans);
+ iwl_pcie_tx_start(trans, scd_addr);
+}
+
static void iwl_trans_pcie_stop_device(struct iwl_trans *trans, bool low_power)
{
struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
When we load the firmware, we hold trans_pcie->mutex to avoid nested flows. We also rely on the ISR to wake up the thread when the DMA has finished copying a chunk. During this flow, we enable the RF-Kill interrupt. The problem is that the RF-Kill interrupt handler can take the mutex and bring the device down. This means that if we load the firmware while the RF-Kill switch is enabled (which will happen when we load the INIT firmware to read the device's capabilities and register to mac80211), we may get an RF-Kill interrupt immediately and the ISR will be waiting for the mutex held by the thread that is currently loading the firmware. At this stage, the ISR won't be able to service the DMA's interrupt needed to wake up the thread that load the firmware. We are in a deadlock situation which ends when the thread that loads the firmware fails on timeout and releases the mutex. To fix this, take the mutex later in the flow, disable the interrupts and synchronize_irq() to give a chance to the RF-Kill interrupt to run and complete. After that, mask all the interrupts besides the DMA interrupt and proceed with firmware load. Make sure to check that there was no RF-Kill interrupt when the interrupts were disabled. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=111361 Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> --- drivers/net/wireless/intel/iwlwifi/pcie/internal.h | 9 + drivers/net/wireless/intel/iwlwifi/pcie/rx.c | 8 +- drivers/net/wireless/intel/iwlwifi/pcie/trans.c | 188 ++++++++++++--------- 3 files changed, 123 insertions(+), 82 deletions(-)