[02/13] spi: imx: use proper dev_* functions for driver messages
diff mbox

Message ID 1455715739-25161-3-git-send-email-s.hauer@pengutronix.de
State Accepted
Commit 6aa800ca65b1788e8c2e4ffd1e57a4c4355fe0ed
Headers show

Commit Message

Sascha Hauer Feb. 17, 2016, 1:28 p.m. UTC
Add a struct device * member to the private driver data and use
it to print messages using dev_* functions rather than pr_*.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 drivers/spi/spi-imx.c | 27 ++++++++++++---------------
 1 file changed, 12 insertions(+), 15 deletions(-)

Patch
diff mbox

diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
index 08492d6..7904d45 100644
--- a/drivers/spi/spi-imx.c
+++ b/drivers/spi/spi-imx.c
@@ -86,6 +86,7 @@  struct spi_imx_devtype_data {
 
 struct spi_imx_data {
 	struct spi_bitbang bitbang;
+	struct device *dev;
 
 	struct completion xfer_done;
 	void __iomem *base;
@@ -250,14 +251,15 @@  static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi,
 #define MX51_ECSPI_TESTREG_LBC	BIT(31)
 
 /* MX51 eCSPI */
-static unsigned int mx51_ecspi_clkdiv(unsigned int fin, unsigned int fspi,
-				      unsigned int *fres)
+static unsigned int mx51_ecspi_clkdiv(struct spi_imx_data *spi_imx,
+				      unsigned int fspi, unsigned int *fres)
 {
 	/*
 	 * there are two 4-bit dividers, the pre-divider divides by
 	 * $pre, the post-divider by 2^$post
 	 */
 	unsigned int pre, post;
+	unsigned int fin = spi_imx->spi_clk;
 
 	if (unlikely(fspi > fin))
 		return 0;
@@ -270,14 +272,14 @@  static unsigned int mx51_ecspi_clkdiv(unsigned int fin, unsigned int fspi,
 
 	post = max(4U, post) - 4;
 	if (unlikely(post > 0xf)) {
-		pr_err("%s: cannot set clock freq: %u (base freq: %u)\n",
-				__func__, fspi, fin);
+		dev_err(spi_imx->dev, "cannot set clock freq: %u (base freq: %u)\n",
+				fspi, fin);
 		return 0xff;
 	}
 
 	pre = DIV_ROUND_UP(fin, fspi << post) - 1;
 
-	pr_debug("%s: fin: %u, fspi: %u, post: %u, pre: %u\n",
+	dev_dbg(spi_imx->dev, "%s: fin: %u, fspi: %u, post: %u, pre: %u\n",
 			__func__, fin, fspi, post, pre);
 
 	/* Resulting frequency for the SCLK line. */
@@ -330,7 +332,7 @@  static int __maybe_unused mx51_ecspi_config(struct spi_imx_data *spi_imx,
 	ctrl |= MX51_ECSPI_CTRL_MODE_MASK;
 
 	/* set clock speed */
-	ctrl |= mx51_ecspi_clkdiv(spi_imx->spi_clk, config->speed_hz, &clk);
+	ctrl |= mx51_ecspi_clkdiv(spi_imx, config->speed_hz, &clk);
 
 	/* set chip select to use */
 	ctrl |= MX51_ECSPI_CTRL_CS(config->cs);
@@ -968,18 +970,14 @@  static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
 	timeout = wait_for_completion_timeout(&spi_imx->dma_tx_completion,
 						IMX_DMA_TIMEOUT);
 	if (!timeout) {
-		pr_warn("%s %s: I/O Error in DMA TX\n",
-			dev_driver_string(&master->dev),
-			dev_name(&master->dev));
+		dev_err(spi_imx->dev, "I/O Error in DMA TX\n");
 		dmaengine_terminate_all(master->dma_tx);
 		dmaengine_terminate_all(master->dma_rx);
 	} else {
 		timeout = wait_for_completion_timeout(
 				&spi_imx->dma_rx_completion, IMX_DMA_TIMEOUT);
 		if (!timeout) {
-			pr_warn("%s %s: I/O Error in DMA RX\n",
-				dev_driver_string(&master->dev),
-				dev_name(&master->dev));
+			dev_err(spi_imx->dev, "I/O Error in DMA RX\n");
 			spi_imx->devtype_data->reset(spi_imx);
 			dmaengine_terminate_all(master->dma_rx);
 		}
@@ -996,9 +994,7 @@  static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
 	return ret;
 
 no_dma:
-	pr_warn_once("%s %s: DMA not available, falling back to PIO\n",
-		     dev_driver_string(&master->dev),
-		     dev_name(&master->dev));
+	dev_warn_once(spi_imx->dev, "DMA not available, falling back to PIO\n");
 	return -EAGAIN;
 }
 
@@ -1128,6 +1124,7 @@  static int spi_imx_probe(struct platform_device *pdev)
 
 	spi_imx = spi_master_get_devdata(master);
 	spi_imx->bitbang.master = master;
+	spi_imx->dev = &pdev->dev;
 
 	spi_imx->devtype_data = of_id ? of_id->data :
 		(struct spi_imx_devtype_data *)pdev->id_entry->driver_data;