[RESEND,2/2] regulator: mt6397: Add buck change mode regulator interface for mt6397
diff mbox

Message ID 1462959090-2877-3-git-send-email-henryc.chen@mediatek.com
State New
Headers show

Commit Message

Henry Chen May 11, 2016, 9:31 a.m. UTC
BUCKs of mt6397 have auto mode and pwm mode.
User can use regulator interfaces to control modes.

Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
---
 .../bindings/regulator/mt6397-regulator.txt        | 22 +++++
 drivers/regulator/mt6397-regulator.c               | 95 +++++++++++++++++++---
 2 files changed, 105 insertions(+), 12 deletions(-)

Comments

Henry Chen May 13, 2016, 8:04 a.m. UTC | #1
Hi Mark,

On Wed, 2016-05-11 at 15:50 +0100, Mark Brown wrote:
> On Wed, May 11, 2016 at 05:31:30PM +0800, Henry Chen wrote:
> 
> > +The possible values for "regulator-supported-modes" are:
> > +	0: PWM mode, mapping to regulator fast mode, allow the
> > +	converter to remain in the PWM mode regardless of the load current, so
> > +	that the noise spectrum of the converter can be minimized for certain
> > +	highly-noise-sensitive handset applications.
> > +	1: Auto mode, mapping to regulator normal mode, mode switch by current
> > +	loading. At light load currents, the converter automatically enters
> > +	PFM mode to save power and improve light load efficiency. At heavy
> > +	load currents, the converter automatically enters PWM mode to minimiz
> > +	the noise spectrum of the converter.
> 
> The details of how this maps onto Linux shouldn't be in the bindings.
> 
> > +				regulator-allow-change-mode;
> > +				regulator-supported-modes = <0 1>;
> 
> These are problematic too as covered in my other mail. 
> 
> > -static struct regulator_ops mt6397_volt_range_ops = {
> > +static const struct regulator_ops mt6397_volt_range_ops = {
> 
> The constification is fine but an unrelated change.  Otherwise this
> looks fine from a code point of view, let's get that merged separately.

Okay, although we didn't have conclusion and solution for regulator
operation mode, as you said that we can get some patch merged
separately, so I will resend the patch which clean up comments from
you and Daniel.

Patch
diff mbox

diff --git a/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt
index a42b1d6..d3167f2 100644
--- a/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt
@@ -7,6 +7,26 @@  Required properties:
   The definition for each of these nodes is defined using the standard binding
   for regulators at Documentation/devicetree/bindings/regulator/regulator.txt.
 
+The mt6397 buck supports two different operating modes: Fast and Normal
+Mode. Some regulators support the modes to be changed by the consumers during
+normal operation.
+
+The regulators that support the standard "regulator-allow-change-mode" property,
+changing their mode during normal operation are:
+  buck_vpca15, buck_vpca7, buck_vsramca15, buck_vsramca7, buck_vcore, buck_vgpu,
+  buck_vdrm, buck_vio18
+
+The possible values for "regulator-supported-modes" are:
+	0: PWM mode, mapping to regulator fast mode, allow the
+	converter to remain in the PWM mode regardless of the load current, so
+	that the noise spectrum of the converter can be minimized for certain
+	highly-noise-sensitive handset applications.
+	1: Auto mode, mapping to regulator normal mode, mode switch by current
+	loading. At light load currents, the converter automatically enters
+	PFM mode to save power and improve light load efficiency. At heavy
+	load currents, the converter automatically enters PWM mode to minimiz
+	the noise spectrum of the converter.
+
 The valid names for regulators are::
 BUCK:
   buck_vpca15, buck_vpca7, buck_vsramca15, buck_vsramca7, buck_vcore, buck_vgpu,
@@ -30,6 +50,8 @@  Example:
 				regulator-max-microvolt = <1350000>;
 				regulator-ramp-delay = <12500>;
 				regulator-enable-ramp-delay = <200>;
+				regulator-allow-change-mode;
+				regulator-supported-modes = <0 1>;
 			};
 
 			mt6397_vpca7_reg: buck_vpca7 {
diff --git a/drivers/regulator/mt6397-regulator.c b/drivers/regulator/mt6397-regulator.c
index 17a5b6c..c6c6aa85 100644
--- a/drivers/regulator/mt6397-regulator.c
+++ b/drivers/regulator/mt6397-regulator.c
@@ -23,6 +23,9 @@ 
 #include <linux/regulator/mt6397-regulator.h>
 #include <linux/regulator/of_regulator.h>
 
+#define MT6397_BUCK_MODE_AUTO	0
+#define MT6397_BUCK_MODE_FORCE_PWM	1
+
 /*
  * MT6397 regulators' information
  *
@@ -38,10 +41,14 @@  struct mt6397_regulator_info {
 	u32 vselon_reg;
 	u32 vselctrl_reg;
 	u32 vselctrl_mask;
+	u32 modeset_reg;
+	u32 modeset_mask;
+	u32 modeset_shift;
 };
 
 #define MT6397_BUCK(match, vreg, min, max, step, volt_ranges, enreg,	\
-		vosel, vosel_mask, voselon, vosel_ctrl)			\
+		vosel, vosel_mask, voselon, vosel_ctrl, _modeset_reg,	\
+		_modeset_shift)					\
 [MT6397_ID_##vreg] = {							\
 	.desc = {							\
 		.name = #vreg,						\
@@ -62,6 +69,9 @@  struct mt6397_regulator_info {
 	.vselon_reg = voselon,						\
 	.vselctrl_reg = vosel_ctrl,					\
 	.vselctrl_mask = BIT(1),					\
+	.modeset_reg = _modeset_reg,					\
+	.modeset_mask = BIT(_modeset_shift),				\
+	.modeset_shift = _modeset_shift					\
 }
 
 #define MT6397_LDO(match, vreg, ldo_volt_table, enreg, enbit, vosel,	\
@@ -145,6 +155,63 @@  static const u32 ldo_volt_table7[] = {
 	1300000, 1500000, 1800000, 2000000, 2500000, 2800000, 3000000, 3300000,
 };
 
+static int mt6397_regulator_set_mode(struct regulator_dev *rdev,
+				     unsigned int mode)
+{
+	struct mt6397_regulator_info *info = rdev_get_drvdata(rdev);
+	int ret, val;
+
+	switch (mode) {
+	case REGULATOR_MODE_FAST:
+		val = MT6397_BUCK_MODE_FORCE_PWM;
+		break;
+	case REGULATOR_MODE_NORMAL:
+		val = MT6397_BUCK_MODE_AUTO;
+		break;
+	default:
+		ret = -EINVAL;
+		goto err_mode;
+	}
+
+	dev_dbg(&rdev->dev, "mt6397 buck set_mode %#x, %#x, %#x, %#x\n",
+		info->modeset_reg, info->modeset_mask,
+		info->modeset_shift, val);
+
+	val <<= info->modeset_shift;
+	ret = regmap_update_bits(rdev->regmap, info->modeset_reg,
+				 info->modeset_mask, val);
+err_mode:
+	if (ret != 0) {
+		dev_err(&rdev->dev,
+			"Failed to set mt6397 buck mode: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static unsigned int mt6397_regulator_get_mode(struct regulator_dev *rdev)
+{
+	struct mt6397_regulator_info *info = rdev_get_drvdata(rdev);
+	int ret, regval;
+
+	ret = regmap_read(rdev->regmap, info->modeset_reg, &regval);
+	if (ret != 0) {
+		dev_err(&rdev->dev,
+			"Failed to get mt6397 buck mode: %d\n", ret);
+		return ret;
+	}
+
+	switch ((regval & info->modeset_mask) >> info->modeset_shift) {
+	case MT6397_BUCK_MODE_AUTO:
+		return REGULATOR_MODE_NORMAL;
+	case MT6397_BUCK_MODE_FORCE_PWM:
+		return REGULATOR_MODE_FAST;
+	default:
+		return -EINVAL;
+	}
+}
+
 static int mt6397_get_status(struct regulator_dev *rdev)
 {
 	int ret;
@@ -160,7 +227,7 @@  static int mt6397_get_status(struct regulator_dev *rdev)
 	return (regval & info->qi) ? REGULATOR_STATUS_ON : REGULATOR_STATUS_OFF;
 }
 
-static struct regulator_ops mt6397_volt_range_ops = {
+static const struct regulator_ops mt6397_volt_range_ops = {
 	.list_voltage = regulator_list_voltage_linear_range,
 	.map_voltage = regulator_map_voltage_linear_range,
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
@@ -170,9 +237,11 @@  static struct regulator_ops mt6397_volt_range_ops = {
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
 	.get_status = mt6397_get_status,
+	.set_mode = mt6397_regulator_set_mode,
+	.get_mode = mt6397_regulator_get_mode,
 };
 
-static struct regulator_ops mt6397_volt_table_ops = {
+static const struct regulator_ops mt6397_volt_table_ops = {
 	.list_voltage = regulator_list_voltage_table,
 	.map_voltage = regulator_map_voltage_iterate,
 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
@@ -184,7 +253,7 @@  static struct regulator_ops mt6397_volt_table_ops = {
 	.get_status = mt6397_get_status,
 };
 
-static struct regulator_ops mt6397_volt_fixed_ops = {
+static const struct regulator_ops mt6397_volt_fixed_ops = {
 	.list_voltage = regulator_list_voltage_linear,
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
@@ -196,28 +265,30 @@  static struct regulator_ops mt6397_volt_fixed_ops = {
 static struct mt6397_regulator_info mt6397_regulators[] = {
 	MT6397_BUCK("buck_vpca15", VPCA15, 700000, 1493750, 6250,
 		buck_volt_range1, MT6397_VCA15_CON7, MT6397_VCA15_CON9, 0x7f,
-		MT6397_VCA15_CON10, MT6397_VCA15_CON5),
+		MT6397_VCA15_CON10, MT6397_VCA15_CON5, MT6397_VCA15_CON2, 11),
 	MT6397_BUCK("buck_vpca7", VPCA7, 700000, 1493750, 6250,
 		buck_volt_range1, MT6397_VPCA7_CON7, MT6397_VPCA7_CON9, 0x7f,
-		MT6397_VPCA7_CON10, MT6397_VPCA7_CON5),
+		MT6397_VPCA7_CON10, MT6397_VPCA7_CON5, MT6397_VPCA7_CON2, 8),
 	MT6397_BUCK("buck_vsramca15", VSRAMCA15, 700000, 1493750, 6250,
 		buck_volt_range1, MT6397_VSRMCA15_CON7, MT6397_VSRMCA15_CON9,
-		0x7f, MT6397_VSRMCA15_CON10, MT6397_VSRMCA15_CON5),
+		0x7f, MT6397_VSRMCA15_CON10, MT6397_VSRMCA15_CON5,
+		MT6397_VSRMCA15_CON2, 8),
 	MT6397_BUCK("buck_vsramca7", VSRAMCA7, 700000, 1493750, 6250,
 		buck_volt_range1, MT6397_VSRMCA7_CON7, MT6397_VSRMCA7_CON9,
-		0x7f, MT6397_VSRMCA7_CON10, MT6397_VSRMCA7_CON5),
+		0x7f, MT6397_VSRMCA7_CON10, MT6397_VSRMCA7_CON5,
+		MT6397_VSRMCA7_CON2, 8),
 	MT6397_BUCK("buck_vcore", VCORE, 700000, 1493750, 6250,
 		buck_volt_range1, MT6397_VCORE_CON7, MT6397_VCORE_CON9, 0x7f,
-		MT6397_VCORE_CON10, MT6397_VCORE_CON5),
+		MT6397_VCORE_CON10, MT6397_VCORE_CON5, MT6397_VCORE_CON2, 8),
 	MT6397_BUCK("buck_vgpu", VGPU, 700000, 1493750, 6250, buck_volt_range1,
 		MT6397_VGPU_CON7, MT6397_VGPU_CON9, 0x7f,
-		MT6397_VGPU_CON10, MT6397_VGPU_CON5),
+		MT6397_VGPU_CON10, MT6397_VGPU_CON5, MT6397_VGPU_CON2, 8),
 	MT6397_BUCK("buck_vdrm", VDRM, 800000, 1593750, 6250, buck_volt_range2,
 		MT6397_VDRM_CON7, MT6397_VDRM_CON9, 0x7f,
-		MT6397_VDRM_CON10, MT6397_VDRM_CON5),
+		MT6397_VDRM_CON10, MT6397_VDRM_CON5, MT6397_VDRM_CON2, 8),
 	MT6397_BUCK("buck_vio18", VIO18, 1500000, 2120000, 20000,
 		buck_volt_range3, MT6397_VIO18_CON7, MT6397_VIO18_CON9, 0x1f,
-		MT6397_VIO18_CON10, MT6397_VIO18_CON5),
+		MT6397_VIO18_CON10, MT6397_VIO18_CON5, MT6397_VIO18_CON2, 8),
 	MT6397_REG_FIXED("ldo_vtcxo", VTCXO, MT6397_ANALDO_CON0, 10, 2800000),
 	MT6397_REG_FIXED("ldo_va28", VA28, MT6397_ANALDO_CON1, 14, 2800000),
 	MT6397_LDO("ldo_vcama", VCAMA, ldo_volt_table1,