diff mbox

[4/5] spi: remove obsolete spi-s3c24xx-gpio driver

Message ID 1309265357-15879-5-git-send-email-jacmet@sunsite.dk (mailing list archive)
State New, archived
Headers show

Commit Message

Peter Korsgaard June 28, 2011, 12:49 p.m. UTC
It was equivalent to spi-gpio, and there's no longer any in-tree users
of it, so get rid of it.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
---
 drivers/spi/Kconfig            |   10 --
 drivers/spi/Makefile           |    1 -
 drivers/spi/spi-s3c24xx-gpio.c |  200 ----------------------------------------
 3 files changed, 0 insertions(+), 211 deletions(-)
 delete mode 100644 drivers/spi/spi-s3c24xx-gpio.c
diff mbox

Patch

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index c013481..9aafa98 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -313,16 +313,6 @@  config SPI_S3C24XX_FIQ
 	  no free DMA channels, or when doing transfers that required both
 	  TX and RX data paths.
 
-config SPI_S3C24XX_GPIO
-	tristate "Samsung S3C24XX series SPI by GPIO"
-	depends on ARCH_S3C2410 && EXPERIMENTAL
-	select SPI_BITBANG
-	help
-	  SPI driver for Samsung S3C24XX series ARM SoCs using
-	  GPIO lines to provide the SPI bus. This can be used where
-	  the inbuilt hardware cannot provide the transfer mode, or
-	  where the board is using non hardware connected pins.
-
 config SPI_S3C64XX
 	tristate "Samsung S3C64XX series type SPI"
 	depends on (ARCH_S3C64XX || ARCH_S5P64X0)
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index b60b04b..61c3261 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -44,7 +44,6 @@  obj-$(CONFIG_SPI_PL022)			+= spi-pl022.o
 obj-$(CONFIG_SPI_PPC4xx)		+= spi-ppc4xx.o
 obj-$(CONFIG_SPI_PXA2XX)		+= spi-pxa2xx.o
 obj-$(CONFIG_SPI_PXA2XX_PCI)		+= spi-pxa2xx-pci.o
-obj-$(CONFIG_SPI_S3C24XX_GPIO)		+= spi-s3c24xx-gpio.o
 obj-$(CONFIG_SPI_S3C24XX)		+= spi-s3c24xx-hw.o
 spi-s3c24xx-hw-y			:= spi-s3c24xx.o
 spi-s3c24xx-hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi-s3c24xx-fiq.o
diff --git a/drivers/spi/spi-s3c24xx-gpio.c b/drivers/spi/spi-s3c24xx-gpio.c
deleted file mode 100644
index 2d3c085..0000000
--- a/drivers/spi/spi-s3c24xx-gpio.c
+++ /dev/null
@@ -1,200 +0,0 @@ 
-/*
- * Copyright (c) 2006 Ben Dooks
- * Copyright (c) 2006 Simtec Electronics
- *
- * S3C24XX GPIO based SPI driver
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
-*/
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/spinlock.h>
-#include <linux/workqueue.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-
-#include <linux/spi/spi.h>
-#include <linux/spi/spi_bitbang.h>
-
-#include <mach/regs-gpio.h>
-#include <mach/spi-gpio.h>
-#include <mach/hardware.h>
-
-struct s3c2410_spigpio {
-	struct spi_bitbang		 bitbang;
-
-	struct s3c2410_spigpio_info	*info;
-	struct platform_device		*dev;
-};
-
-static inline struct s3c2410_spigpio *spidev_to_sg(struct spi_device *spi)
-{
-	return spi_master_get_devdata(spi->master);
-}
-
-static inline void setsck(struct spi_device *dev, int on)
-{
-	struct s3c2410_spigpio *sg = spidev_to_sg(dev);
-	s3c2410_gpio_setpin(sg->info->pin_clk, on ? 1 : 0);
-}
-
-static inline void setmosi(struct spi_device *dev, int on)
-{
-	struct s3c2410_spigpio *sg = spidev_to_sg(dev);
-	s3c2410_gpio_setpin(sg->info->pin_mosi, on ? 1 : 0);
-}
-
-static inline u32 getmiso(struct spi_device *dev)
-{
-	struct s3c2410_spigpio *sg = spidev_to_sg(dev);
-	return s3c2410_gpio_getpin(sg->info->pin_miso) ? 1 : 0;
-}
-
-#define spidelay(x) ndelay(x)
-
-#include "spi-bitbang-txrx.h"
-
-
-static u32 s3c2410_spigpio_txrx_mode0(struct spi_device *spi,
-				      unsigned nsecs, u32 word, u8 bits)
-{
-	return bitbang_txrx_be_cpha0(spi, nsecs, 0, 0, word, bits);
-}
-
-static u32 s3c2410_spigpio_txrx_mode1(struct spi_device *spi,
-				      unsigned nsecs, u32 word, u8 bits)
-{
-	return bitbang_txrx_be_cpha1(spi, nsecs, 0, 0, word, bits);
-}
-
-static u32 s3c2410_spigpio_txrx_mode2(struct spi_device *spi,
-				      unsigned nsecs, u32 word, u8 bits)
-{
-	return bitbang_txrx_be_cpha0(spi, nsecs, 1, 0, word, bits);
-}
-
-static u32 s3c2410_spigpio_txrx_mode3(struct spi_device *spi,
-				      unsigned nsecs, u32 word, u8 bits)
-{
-	return bitbang_txrx_be_cpha1(spi, nsecs, 1, 0, word, bits);
-}
-
-
-static void s3c2410_spigpio_chipselect(struct spi_device *dev, int value)
-{
-	struct s3c2410_spigpio *sg = spidev_to_sg(dev);
-
-	if (sg->info && sg->info->chip_select)
-		(sg->info->chip_select)(sg->info, value);
-}
-
-static int s3c2410_spigpio_probe(struct platform_device *dev)
-{
-	struct s3c2410_spigpio_info *info;
-	struct spi_master	*master;
-	struct s3c2410_spigpio  *sp;
-	int ret;
-
-	master = spi_alloc_master(&dev->dev, sizeof(struct s3c2410_spigpio));
-	if (master == NULL) {
-		dev_err(&dev->dev, "failed to allocate spi master\n");
-		ret = -ENOMEM;
-		goto err;
-	}
-
-	sp = spi_master_get_devdata(master);
-
-	platform_set_drvdata(dev, sp);
-
-	/* copy in the plkatform data */
-	info = sp->info = dev->dev.platform_data;
-
-	/* setup spi bitbang adaptor */
-	sp->bitbang.master = spi_master_get(master);
-	sp->bitbang.master->bus_num = info->bus_num;
-	sp->bitbang.master->num_chipselect = info->num_chipselect;
-	sp->bitbang.chipselect = s3c2410_spigpio_chipselect;
-
-	sp->bitbang.txrx_word[SPI_MODE_0] = s3c2410_spigpio_txrx_mode0;
-	sp->bitbang.txrx_word[SPI_MODE_1] = s3c2410_spigpio_txrx_mode1;
-	sp->bitbang.txrx_word[SPI_MODE_2] = s3c2410_spigpio_txrx_mode2;
-	sp->bitbang.txrx_word[SPI_MODE_3] = s3c2410_spigpio_txrx_mode3;
-
-	/* set state of spi pins, always assume that the clock is
-	 * available, but do check the MOSI and MISO. */
-	s3c2410_gpio_setpin(info->pin_clk, 0);
-	s3c2410_gpio_cfgpin(info->pin_clk, S3C2410_GPIO_OUTPUT);
-
-	if (info->pin_mosi < S3C2410_GPH10) {
-		s3c2410_gpio_setpin(info->pin_mosi, 0);
-		s3c2410_gpio_cfgpin(info->pin_mosi, S3C2410_GPIO_OUTPUT);
-	}
-
-	if (info->pin_miso != S3C2410_GPA0 && info->pin_miso < S3C2410_GPH10)
-		s3c2410_gpio_cfgpin(info->pin_miso, S3C2410_GPIO_INPUT);
-
-	ret = spi_bitbang_start(&sp->bitbang);
-	if (ret)
-		goto err_no_bitbang;
-
-	return 0;
-
- err_no_bitbang:
-	spi_master_put(sp->bitbang.master);
- err:
-	return ret;
-
-}
-
-static int s3c2410_spigpio_remove(struct platform_device *dev)
-{
-	struct s3c2410_spigpio *sp = platform_get_drvdata(dev);
-
-	spi_bitbang_stop(&sp->bitbang);
-	spi_master_put(sp->bitbang.master);
-
-	return 0;
-}
-
-/* all gpio should be held over suspend/resume, so we should
- * not need to deal with this
-*/
-
-#define s3c2410_spigpio_suspend NULL
-#define s3c2410_spigpio_resume NULL
-
-/* work with hotplug and coldplug */
-MODULE_ALIAS("platform:spi_s3c24xx_gpio");
-
-static struct platform_driver s3c2410_spigpio_drv = {
-	.probe		= s3c2410_spigpio_probe,
-        .remove		= s3c2410_spigpio_remove,
-        .suspend	= s3c2410_spigpio_suspend,
-        .resume		= s3c2410_spigpio_resume,
-        .driver		= {
-		.name	= "spi_s3c24xx_gpio",
-		.owner	= THIS_MODULE,
-        },
-};
-
-static int __init s3c2410_spigpio_init(void)
-{
-        return platform_driver_register(&s3c2410_spigpio_drv);
-}
-
-static void __exit s3c2410_spigpio_exit(void)
-{
-        platform_driver_unregister(&s3c2410_spigpio_drv);
-}
-
-module_init(s3c2410_spigpio_init);
-module_exit(s3c2410_spigpio_exit);
-
-MODULE_DESCRIPTION("S3C24XX SPI Driver");
-MODULE_AUTHOR("Ben Dooks, <ben@simtec.co.uk>");
-MODULE_LICENSE("GPL");