diff mbox

[v2,3/6] phy: meson: add USB2 PHY support for Meson8b and GXBB

Message ID 20160911134111.31141-4-martin.blumenstingl@googlemail.com (mailing list archive)
State Superseded
Headers show

Commit Message

Martin Blumenstingl Sept. 11, 2016, 1:41 p.m. UTC 
This is a new driver for the USB PHY found in Meson8b and GXBB SoCs.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
---
 drivers/phy/Kconfig          |  11 ++
 drivers/phy/Makefile         |   1 +
 drivers/phy/phy-meson-usb2.c | 280 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 292 insertions(+)
 create mode 100644 drivers/phy/phy-meson-usb2.c

Comments

Kevin Hilman Sept. 14, 2016, 4:06 p.m. UTC | #1 
Kishon,

Martin Blumenstingl <martin.blumenstingl@googlemail.com> writes:

> This is a new driver for the USB PHY found in Meson8b and GXBB SoCs.
>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
> Tested-by: Kevin Hilman <khilman@baylibre.com>

Will you be picking this up for v4.9?

Kevin

> ---
>  drivers/phy/Kconfig          |  11 ++
>  drivers/phy/Makefile         |   1 +
>  drivers/phy/phy-meson-usb2.c | 280 +++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 292 insertions(+)
>  create mode 100644 drivers/phy/phy-meson-usb2.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 19bff3a..6ad87ec 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -453,4 +453,15 @@ config PHY_NS2_PCIE
>  	help
>  	  Enable this to support the Broadcom Northstar2 PCIe PHY.
>  	  If unsure, say N.
> +
> +config PHY_MESON_USB2
> +	tristate "Meson USB2 PHY driver"
> +	default ARCH_MESON
> +	depends on OF && (ARCH_MESON || COMPILE_TEST)
> +	select GENERIC_PHY
> +	help
> +	  Enable this to support the Meson USB2 PHYs found in Meson8b
> +	  and GXBB SoCs.
> +	  If unsure, say N.
> +
>  endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index 90ae198..dd507ac 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -56,3 +56,4 @@ obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
>  obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o
>  obj-$(CONFIG_ARCH_TEGRA) += tegra/
>  obj-$(CONFIG_PHY_NS2_PCIE)		+= phy-bcm-ns2-pcie.o
> +obj-$(CONFIG_PHY_MESON_USB2)		+= phy-meson-usb2.o
> diff --git a/drivers/phy/phy-meson-usb2.c b/drivers/phy/phy-meson-usb2.c
> new file mode 100644
> index 0000000..eece521
> --- /dev/null
> +++ b/drivers/phy/phy-meson-usb2.c
> @@ -0,0 +1,280 @@
> +/*
> + * Meson USB2 PHY driver
> + *
> + * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/reset.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/usb/of.h>
> +
> +#define REG_CONFIG					0x00
> +	#define REG_CONFIG_CLK_EN			BIT(0)
> +	#define REG_CONFIG_CLK_SEL_MASK			GENMASK(3, 1)
> +	#define REG_CONFIG_CLK_DIV_MASK			GENMASK(10, 4)
> +	#define REG_CONFIG_CLK_32k_ALTSEL		BIT(15)
> +	#define REG_CONFIG_TEST_TRIG			BIT(31)
> +
> +#define REG_CTRL					0x04
> +	#define REG_CTRL_SOFT_PRST			BIT(0)
> +	#define REG_CTRL_SOFT_HRESET			BIT(1)
> +	#define REG_CTRL_SS_SCALEDOWN_MODE_MASK		GENMASK(3, 2)
> +	#define REG_CTRL_CLK_DET_RST			BIT(4)
> +	#define REG_CTRL_INTR_SEL			BIT(5)
> +	#define REG_CTRL_CLK_DETECTED			BIT(8)
> +	#define REG_CTRL_SOF_SENT_RCVD_TGL		BIT(9)
> +	#define REG_CTRL_SOF_TOGGLE_OUT			BIT(10)
> +	#define REG_CTRL_POWER_ON_RESET			BIT(15)
> +	#define REG_CTRL_SLEEPM				BIT(16)
> +	#define REG_CTRL_TX_BITSTUFF_ENN_H		BIT(17)
> +	#define REG_CTRL_TX_BITSTUFF_ENN		BIT(18)
> +	#define REG_CTRL_COMMON_ON			BIT(19)
> +	#define REG_CTRL_REF_CLK_SEL_MASK		GENMASK(21, 20)
> +	#define REG_CTRL_REF_CLK_SEL_SHIFT		20
> +	#define REG_CTRL_FSEL_MASK			GENMASK(24, 22)
> +	#define REG_CTRL_FSEL_SHIFT			22
> +	#define REG_CTRL_PORT_RESET			BIT(25)
> +	#define REG_CTRL_THREAD_ID_MASK			GENMASK(31, 26)
> +
> +#define REG_ENDP_INTR					0x08
> +
> +/* bits [31:26], [24:21] and [15:3] seem to be read-only */
> +#define REG_ADP_BC					0x0c
> +	#define REG_ADP_BC_VBUS_VLD_EXT_SEL		BIT(0)
> +	#define REG_ADP_BC_VBUS_VLD_EXT			BIT(1)
> +	#define REG_ADP_BC_OTG_DISABLE			BIT(2)
> +	#define REG_ADP_BC_ID_PULLUP			BIT(3)
> +	#define REG_ADP_BC_DRV_VBUS			BIT(4)
> +	#define REG_ADP_BC_ADP_PRB_EN			BIT(5)
> +	#define REG_ADP_BC_ADP_DISCHARGE		BIT(6)
> +	#define REG_ADP_BC_ADP_CHARGE			BIT(7)
> +	#define REG_ADP_BC_SESS_END			BIT(8)
> +	#define REG_ADP_BC_DEVICE_SESS_VLD		BIT(9)
> +	#define REG_ADP_BC_B_VALID			BIT(10)
> +	#define REG_ADP_BC_A_VALID			BIT(11)
> +	#define REG_ADP_BC_ID_DIG			BIT(12)
> +	#define REG_ADP_BC_VBUS_VALID			BIT(13)
> +	#define REG_ADP_BC_ADP_PROBE			BIT(14)
> +	#define REG_ADP_BC_ADP_SENSE			BIT(15)
> +	#define REG_ADP_BC_ACA_ENABLE			BIT(16)
> +	#define REG_ADP_BC_DCD_ENABLE			BIT(17)
> +	#define REG_ADP_BC_VDAT_DET_EN_B		BIT(18)
> +	#define REG_ADP_BC_VDAT_SRC_EN_B		BIT(19)
> +	#define REG_ADP_BC_CHARGE_SEL			BIT(20)
> +	#define REG_ADP_BC_CHARGE_DETECT		BIT(21)
> +	#define REG_ADP_BC_ACA_PIN_RANGE_C		BIT(22)
> +	#define REG_ADP_BC_ACA_PIN_RANGE_B		BIT(23)
> +	#define REG_ADP_BC_ACA_PIN_RANGE_A		BIT(24)
> +	#define REG_ADP_BC_ACA_PIN_GND			BIT(25)
> +	#define REG_ADP_BC_ACA_PIN_FLOAT		BIT(26)
> +
> +#define REG_DBG_UART					0x14
> +
> +#define REG_TEST					0x18
> +	#define REG_TEST_DATA_IN_MASK			GENMASK(3, 0)
> +	#define REG_TEST_EN_MASK			GENMASK(7, 4)
> +	#define REG_TEST_ADDR_MASK			GENMASK(11, 8)
> +	#define REG_TEST_DATA_OUT_SEL			BIT(12)
> +	#define REG_TEST_CLK				BIT(13)
> +	#define REG_TEST_VA_TEST_EN_B_MASK		GENMASK(15, 14)
> +	#define REG_TEST_DATA_OUT_MASK			GENMASK(19, 16)
> +	#define REG_TEST_DISABLE_ID_PULLUP		BIT(20)
> +
> +#define REG_TUNE					0x1c
> +	#define REG_TUNE_TX_RES_TUNE_MASK		GENMASK(1, 0)
> +	#define REG_TUNE_TX_HSXV_TUNE_MASK		GENMASK(3, 2)
> +	#define REG_TUNE_TX_VREF_TUNE_MASK		GENMASK(7, 4)
> +	#define REG_TUNE_TX_RISE_TUNE_MASK		GENMASK(9, 8)
> +	#define REG_TUNE_TX_PREEMP_PULSE_TUNE		BIT(10)
> +	#define REG_TUNE_TX_PREEMP_AMP_TUNE_MASK	GENMASK(12, 11)
> +	#define REG_TUNE_TX_FSLS_TUNE_MASK		GENMASK(16, 13)
> +	#define REG_TUNE_SQRX_TUNE_MASK			GENMASK(19, 17)
> +	#define REG_TUNE_OTG_TUNE			GENMASK(22, 20)
> +	#define REG_TUNE_COMP_DIS_TUNE			GENMASK(25, 23)
> +	#define REG_TUNE_HOST_DM_PULLDOWN		BIT(26)
> +	#define REG_TUNE_HOST_DP_PULLDOWN		BIT(27)
> +
> +#define RESET_COMPLETE_TIME				500
> +#define ACA_ENABLE_COMPLETE_TIME			50
> +
> +struct phy_meson_usb2_priv {
> +	void __iomem		*regs;
> +	enum usb_dr_mode	dr_mode;
> +	struct clk		*clk_usb_general;
> +	struct clk		*clk_usb;
> +};
> +
> +static u32 phy_meson_usb2_read(struct phy_meson_usb2_priv *phy_priv, u32 reg)
> +{
> +	return readl(phy_priv->regs + reg);
> +}
> +
> +static void phy_meson_usb2_mask_bits(struct phy_meson_usb2_priv *phy_priv,
> +				     u32 reg, u32 mask, u32 value)
> +{
> +	u32 data;
> +
> +	data = phy_meson_usb2_read(phy_priv, reg);
> +	data &= ~mask;
> +	data |= (value & mask);
> +
> +	writel(data, phy_priv->regs + reg);
> +}
> +
> +static int phy_meson_usb2_power_on(struct phy *phy)
> +{
> +	struct phy_meson_usb2_priv *priv = phy_get_drvdata(phy);
> +	int ret;
> +
> +	ret = clk_prepare_enable(priv->clk_usb_general);
> +	if (ret) {
> +		dev_err(&phy->dev, "Failed to enable USB general clock\n");
> +		return ret;
> +	}
> +
> +	ret = clk_prepare_enable(priv->clk_usb);
> +	if (ret) {
> +		dev_err(&phy->dev, "Failed to enable USB DDR clock\n");
> +		return ret;
> +	}
> +
> +	phy_meson_usb2_mask_bits(priv, REG_CONFIG, REG_CONFIG_CLK_32k_ALTSEL,
> +				 REG_CONFIG_CLK_32k_ALTSEL);
> +
> +	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_REF_CLK_SEL_MASK,
> +				 0x2 << REG_CTRL_REF_CLK_SEL_SHIFT);
> +
> +	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_FSEL_MASK,
> +				 0x5 << REG_CTRL_FSEL_SHIFT);
> +
> +	/* reset the PHY */
> +	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_POWER_ON_RESET,
> +				 REG_CTRL_POWER_ON_RESET);
> +	udelay(RESET_COMPLETE_TIME);
> +	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_POWER_ON_RESET, 0);
> +	udelay(RESET_COMPLETE_TIME);
> +
> +	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_SOF_TOGGLE_OUT,
> +				 REG_CTRL_SOF_TOGGLE_OUT);
> +
> +	if (priv->dr_mode == USB_DR_MODE_HOST) {
> +		phy_meson_usb2_mask_bits(priv, REG_ADP_BC,
> +					 REG_ADP_BC_ACA_ENABLE,
> +					 REG_ADP_BC_ACA_ENABLE);
> +
> +		udelay(ACA_ENABLE_COMPLETE_TIME);
> +
> +		if (phy_meson_usb2_read(priv, REG_ADP_BC) &
> +			REG_ADP_BC_ACA_PIN_FLOAT) {
> +			dev_warn(&phy->dev, "USB ID detect failed!\n");
> +			return -EINVAL;
> +		}
> +	}
> +
> +	return 0;
> +}
> +
> +static int phy_meson_usb2_power_off(struct phy *phy)
> +{
> +	struct phy_meson_usb2_priv *priv = phy_get_drvdata(phy);
> +
> +	clk_disable_unprepare(priv->clk_usb);
> +	clk_disable_unprepare(priv->clk_usb_general);
> +
> +	return 0;
> +}
> +
> +static const struct phy_ops phy_meson_usb2_ops = {
> +	.power_on	= phy_meson_usb2_power_on,
> +	.power_off	= phy_meson_usb2_power_off,
> +	.owner		= THIS_MODULE,
> +};
> +
> +static int phy_meson_usb2_probe(struct platform_device *pdev)
> +{
> +	struct phy_meson_usb2_priv *priv;
> +	struct resource *res;
> +	struct phy *phy;
> +	struct phy_provider *phy_provider;
> +	int ret;
> +
> +	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	priv->regs = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(priv->regs))
> +		return PTR_ERR(priv->regs);
> +
> +	priv->clk_usb_general = devm_clk_get(&pdev->dev, "usb_general");
> +	if (IS_ERR(priv->clk_usb_general))
> +		return PTR_ERR(priv->clk_usb_general);
> +
> +	priv->clk_usb = devm_clk_get(&pdev->dev, "usb");
> +	if (IS_ERR(priv->clk_usb))
> +		return PTR_ERR(priv->clk_usb);
> +
> +	priv->dr_mode = of_usb_get_dr_mode_by_phy(pdev->dev.of_node, -1);
> +	if (priv->dr_mode == USB_DR_MODE_UNKNOWN) {
> +		dev_err(&pdev->dev,
> +			"missing dual role configuration of the controller\n");
> +		return -EINVAL;
> +	}
> +
> +	phy = devm_phy_create(&pdev->dev, NULL, &phy_meson_usb2_ops);
> +	if (IS_ERR(phy)) {
> +		dev_err(&pdev->dev, "failed to create PHY\n");
> +		return PTR_ERR(phy);
> +	}
> +
> +	/*
> +	 * No actual error check here because the hardware only has one reset
> +	 * line for both PHYs. Using a shared reset is not possible because we
> +	 * must call reset_control_reset to trigger the reset (which is not
> +	 * allowed for shared resets in the reset framework).
> +	 */
> +	ret = device_reset_optional(&pdev->dev);
> +	if (ret == -EPROBE_DEFER)
> +		return ret;
> +
> +	phy_set_drvdata(phy, priv);
> +
> +	phy_provider =
> +		devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
> +
> +	return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static const struct of_device_id phy_meson_usb2_of_match[] = {
> +	{ .compatible = "amlogic,meson8b-usb2-phy", },
> +	{ .compatible = "amlogic,meson-gxbb-usb2-phy", },
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, phy_meson_usb2_of_match);
> +
> +static struct platform_driver phy_meson_usb2_driver = {
> +	.probe	= phy_meson_usb2_probe,
> +	.driver	= {
> +		.name		= "phy-meson-usb2",
> +		.of_match_table	= phy_meson_usb2_of_match,
> +	},
> +};
> +module_platform_driver(phy_meson_usb2_driver);
> +
> +MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
> +MODULE_DESCRIPTION("Meson USB2 PHY driver");
> +MODULE_LICENSE("GPL");
Martin Blumenstingl Sept. 14, 2016, 9:30 p.m. UTC | #2 
On Sun, Sep 11, 2016 at 3:41 PM, Martin Blumenstingl
<martin.blumenstingl@googlemail.com> wrote:
> This is a new driver for the USB PHY found in Meson8b and GXBB SoCs.
>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
> Tested-by: Kevin Hilman <khilman@baylibre.com>
> ---
>  drivers/phy/Kconfig          |  11 ++
>  drivers/phy/Makefile         |   1 +
>  drivers/phy/phy-meson-usb2.c | 280 +++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 292 insertions(+)
>  create mode 100644 drivers/phy/phy-meson-usb2.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 19bff3a..6ad87ec 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -453,4 +453,15 @@ config PHY_NS2_PCIE
>         help
>           Enable this to support the Broadcom Northstar2 PCIe PHY.
>           If unsure, say N.
> +
> +config PHY_MESON_USB2
> +       tristate "Meson USB2 PHY driver"
> +       default ARCH_MESON
> +       depends on OF && (ARCH_MESON || COMPILE_TEST)
> +       select GENERIC_PHY
as pointed out by Arnd Bergmann (see [0]) this is missing a "select
USB_COMMON", just like the PHY_SUN4I_USB and PHY_SUN9I_USB drivers as
we use of_usb_get_dr_mode_by_phy() to get the mode of the USB
controller (as the PHY needs special configuration for host-mode).

I will send an update on Sunday.


Regards,
Martin


[0] http://marc.info/?l=linux-usb&m=147386117604824&w=2
Kishon Vijay Abraham I Sept. 17, 2016, 4:17 a.m. UTC | #3 
Hi Kevin,

On Wednesday 14 September 2016 09:36 PM, Kevin Hilman wrote:
> Kishon,
> 
> Martin Blumenstingl <martin.blumenstingl@googlemail.com> writes:
> 
>> This is a new driver for the USB PHY found in Meson8b and GXBB SoCs.
>>
>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
>> Tested-by: Kevin Hilman <khilman@baylibre.com>
> 
> Will you be picking this up for v4.9?

It's already late for 4.9. Generally send pull request to Greg around -rc6.
This can go only in 4.10.

Thanks
Kishon

> 
> Kevin
> 
>> ---
>>  drivers/phy/Kconfig          |  11 ++
>>  drivers/phy/Makefile         |   1 +
>>  drivers/phy/phy-meson-usb2.c | 280 +++++++++++++++++++++++++++++++++++++++++++
>>  3 files changed, 292 insertions(+)
>>  create mode 100644 drivers/phy/phy-meson-usb2.c
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index 19bff3a..6ad87ec 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -453,4 +453,15 @@ config PHY_NS2_PCIE
>>  	help
>>  	  Enable this to support the Broadcom Northstar2 PCIe PHY.
>>  	  If unsure, say N.
>> +
>> +config PHY_MESON_USB2
>> +	tristate "Meson USB2 PHY driver"
>> +	default ARCH_MESON
>> +	depends on OF && (ARCH_MESON || COMPILE_TEST)
>> +	select GENERIC_PHY
>> +	help
>> +	  Enable this to support the Meson USB2 PHYs found in Meson8b
>> +	  and GXBB SoCs.
>> +	  If unsure, say N.
>> +
>>  endmenu
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index 90ae198..dd507ac 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -56,3 +56,4 @@ obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
>>  obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o
>>  obj-$(CONFIG_ARCH_TEGRA) += tegra/
>>  obj-$(CONFIG_PHY_NS2_PCIE)		+= phy-bcm-ns2-pcie.o
>> +obj-$(CONFIG_PHY_MESON_USB2)		+= phy-meson-usb2.o
>> diff --git a/drivers/phy/phy-meson-usb2.c b/drivers/phy/phy-meson-usb2.c
>> new file mode 100644
>> index 0000000..eece521
>> --- /dev/null
>> +++ b/drivers/phy/phy-meson-usb2.c
>> @@ -0,0 +1,280 @@
>> +/*
>> + * Meson USB2 PHY driver
>> + *
>> + * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/delay.h>
>> +#include <linux/io.h>
>> +#include <linux/module.h>
>> +#include <linux/of_device.h>
>> +#include <linux/reset.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/usb/of.h>
>> +
>> +#define REG_CONFIG					0x00
>> +	#define REG_CONFIG_CLK_EN			BIT(0)
>> +	#define REG_CONFIG_CLK_SEL_MASK			GENMASK(3, 1)
>> +	#define REG_CONFIG_CLK_DIV_MASK			GENMASK(10, 4)
>> +	#define REG_CONFIG_CLK_32k_ALTSEL		BIT(15)
>> +	#define REG_CONFIG_TEST_TRIG			BIT(31)
>> +
>> +#define REG_CTRL					0x04
>> +	#define REG_CTRL_SOFT_PRST			BIT(0)
>> +	#define REG_CTRL_SOFT_HRESET			BIT(1)
>> +	#define REG_CTRL_SS_SCALEDOWN_MODE_MASK		GENMASK(3, 2)
>> +	#define REG_CTRL_CLK_DET_RST			BIT(4)
>> +	#define REG_CTRL_INTR_SEL			BIT(5)
>> +	#define REG_CTRL_CLK_DETECTED			BIT(8)
>> +	#define REG_CTRL_SOF_SENT_RCVD_TGL		BIT(9)
>> +	#define REG_CTRL_SOF_TOGGLE_OUT			BIT(10)
>> +	#define REG_CTRL_POWER_ON_RESET			BIT(15)
>> +	#define REG_CTRL_SLEEPM				BIT(16)
>> +	#define REG_CTRL_TX_BITSTUFF_ENN_H		BIT(17)
>> +	#define REG_CTRL_TX_BITSTUFF_ENN		BIT(18)
>> +	#define REG_CTRL_COMMON_ON			BIT(19)
>> +	#define REG_CTRL_REF_CLK_SEL_MASK		GENMASK(21, 20)
>> +	#define REG_CTRL_REF_CLK_SEL_SHIFT		20
>> +	#define REG_CTRL_FSEL_MASK			GENMASK(24, 22)
>> +	#define REG_CTRL_FSEL_SHIFT			22
>> +	#define REG_CTRL_PORT_RESET			BIT(25)
>> +	#define REG_CTRL_THREAD_ID_MASK			GENMASK(31, 26)
>> +
>> +#define REG_ENDP_INTR					0x08
>> +
>> +/* bits [31:26], [24:21] and [15:3] seem to be read-only */
>> +#define REG_ADP_BC					0x0c
>> +	#define REG_ADP_BC_VBUS_VLD_EXT_SEL		BIT(0)
>> +	#define REG_ADP_BC_VBUS_VLD_EXT			BIT(1)
>> +	#define REG_ADP_BC_OTG_DISABLE			BIT(2)
>> +	#define REG_ADP_BC_ID_PULLUP			BIT(3)
>> +	#define REG_ADP_BC_DRV_VBUS			BIT(4)
>> +	#define REG_ADP_BC_ADP_PRB_EN			BIT(5)
>> +	#define REG_ADP_BC_ADP_DISCHARGE		BIT(6)
>> +	#define REG_ADP_BC_ADP_CHARGE			BIT(7)
>> +	#define REG_ADP_BC_SESS_END			BIT(8)
>> +	#define REG_ADP_BC_DEVICE_SESS_VLD		BIT(9)
>> +	#define REG_ADP_BC_B_VALID			BIT(10)
>> +	#define REG_ADP_BC_A_VALID			BIT(11)
>> +	#define REG_ADP_BC_ID_DIG			BIT(12)
>> +	#define REG_ADP_BC_VBUS_VALID			BIT(13)
>> +	#define REG_ADP_BC_ADP_PROBE			BIT(14)
>> +	#define REG_ADP_BC_ADP_SENSE			BIT(15)
>> +	#define REG_ADP_BC_ACA_ENABLE			BIT(16)
>> +	#define REG_ADP_BC_DCD_ENABLE			BIT(17)
>> +	#define REG_ADP_BC_VDAT_DET_EN_B		BIT(18)
>> +	#define REG_ADP_BC_VDAT_SRC_EN_B		BIT(19)
>> +	#define REG_ADP_BC_CHARGE_SEL			BIT(20)
>> +	#define REG_ADP_BC_CHARGE_DETECT		BIT(21)
>> +	#define REG_ADP_BC_ACA_PIN_RANGE_C		BIT(22)
>> +	#define REG_ADP_BC_ACA_PIN_RANGE_B		BIT(23)
>> +	#define REG_ADP_BC_ACA_PIN_RANGE_A		BIT(24)
>> +	#define REG_ADP_BC_ACA_PIN_GND			BIT(25)
>> +	#define REG_ADP_BC_ACA_PIN_FLOAT		BIT(26)
>> +
>> +#define REG_DBG_UART					0x14
>> +
>> +#define REG_TEST					0x18
>> +	#define REG_TEST_DATA_IN_MASK			GENMASK(3, 0)
>> +	#define REG_TEST_EN_MASK			GENMASK(7, 4)
>> +	#define REG_TEST_ADDR_MASK			GENMASK(11, 8)
>> +	#define REG_TEST_DATA_OUT_SEL			BIT(12)
>> +	#define REG_TEST_CLK				BIT(13)
>> +	#define REG_TEST_VA_TEST_EN_B_MASK		GENMASK(15, 14)
>> +	#define REG_TEST_DATA_OUT_MASK			GENMASK(19, 16)
>> +	#define REG_TEST_DISABLE_ID_PULLUP		BIT(20)
>> +
>> +#define REG_TUNE					0x1c
>> +	#define REG_TUNE_TX_RES_TUNE_MASK		GENMASK(1, 0)
>> +	#define REG_TUNE_TX_HSXV_TUNE_MASK		GENMASK(3, 2)
>> +	#define REG_TUNE_TX_VREF_TUNE_MASK		GENMASK(7, 4)
>> +	#define REG_TUNE_TX_RISE_TUNE_MASK		GENMASK(9, 8)
>> +	#define REG_TUNE_TX_PREEMP_PULSE_TUNE		BIT(10)
>> +	#define REG_TUNE_TX_PREEMP_AMP_TUNE_MASK	GENMASK(12, 11)
>> +	#define REG_TUNE_TX_FSLS_TUNE_MASK		GENMASK(16, 13)
>> +	#define REG_TUNE_SQRX_TUNE_MASK			GENMASK(19, 17)
>> +	#define REG_TUNE_OTG_TUNE			GENMASK(22, 20)
>> +	#define REG_TUNE_COMP_DIS_TUNE			GENMASK(25, 23)
>> +	#define REG_TUNE_HOST_DM_PULLDOWN		BIT(26)
>> +	#define REG_TUNE_HOST_DP_PULLDOWN		BIT(27)
>> +
>> +#define RESET_COMPLETE_TIME				500
>> +#define ACA_ENABLE_COMPLETE_TIME			50
>> +
>> +struct phy_meson_usb2_priv {
>> +	void __iomem		*regs;
>> +	enum usb_dr_mode	dr_mode;
>> +	struct clk		*clk_usb_general;
>> +	struct clk		*clk_usb;
>> +};
>> +
>> +static u32 phy_meson_usb2_read(struct phy_meson_usb2_priv *phy_priv, u32 reg)
>> +{
>> +	return readl(phy_priv->regs + reg);
>> +}
>> +
>> +static void phy_meson_usb2_mask_bits(struct phy_meson_usb2_priv *phy_priv,
>> +				     u32 reg, u32 mask, u32 value)
>> +{
>> +	u32 data;
>> +
>> +	data = phy_meson_usb2_read(phy_priv, reg);
>> +	data &= ~mask;
>> +	data |= (value & mask);
>> +
>> +	writel(data, phy_priv->regs + reg);
>> +}
>> +
>> +static int phy_meson_usb2_power_on(struct phy *phy)
>> +{
>> +	struct phy_meson_usb2_priv *priv = phy_get_drvdata(phy);
>> +	int ret;
>> +
>> +	ret = clk_prepare_enable(priv->clk_usb_general);
>> +	if (ret) {
>> +		dev_err(&phy->dev, "Failed to enable USB general clock\n");
>> +		return ret;
>> +	}
>> +
>> +	ret = clk_prepare_enable(priv->clk_usb);
>> +	if (ret) {
>> +		dev_err(&phy->dev, "Failed to enable USB DDR clock\n");
>> +		return ret;
>> +	}
>> +
>> +	phy_meson_usb2_mask_bits(priv, REG_CONFIG, REG_CONFIG_CLK_32k_ALTSEL,
>> +				 REG_CONFIG_CLK_32k_ALTSEL);
>> +
>> +	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_REF_CLK_SEL_MASK,
>> +				 0x2 << REG_CTRL_REF_CLK_SEL_SHIFT);
>> +
>> +	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_FSEL_MASK,
>> +				 0x5 << REG_CTRL_FSEL_SHIFT);
>> +
>> +	/* reset the PHY */
>> +	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_POWER_ON_RESET,
>> +				 REG_CTRL_POWER_ON_RESET);
>> +	udelay(RESET_COMPLETE_TIME);
>> +	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_POWER_ON_RESET, 0);
>> +	udelay(RESET_COMPLETE_TIME);
>> +
>> +	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_SOF_TOGGLE_OUT,
>> +				 REG_CTRL_SOF_TOGGLE_OUT);
>> +
>> +	if (priv->dr_mode == USB_DR_MODE_HOST) {
>> +		phy_meson_usb2_mask_bits(priv, REG_ADP_BC,
>> +					 REG_ADP_BC_ACA_ENABLE,
>> +					 REG_ADP_BC_ACA_ENABLE);
>> +
>> +		udelay(ACA_ENABLE_COMPLETE_TIME);
>> +
>> +		if (phy_meson_usb2_read(priv, REG_ADP_BC) &
>> +			REG_ADP_BC_ACA_PIN_FLOAT) {
>> +			dev_warn(&phy->dev, "USB ID detect failed!\n");
>> +			return -EINVAL;
>> +		}
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static int phy_meson_usb2_power_off(struct phy *phy)
>> +{
>> +	struct phy_meson_usb2_priv *priv = phy_get_drvdata(phy);
>> +
>> +	clk_disable_unprepare(priv->clk_usb);
>> +	clk_disable_unprepare(priv->clk_usb_general);
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct phy_ops phy_meson_usb2_ops = {
>> +	.power_on	= phy_meson_usb2_power_on,
>> +	.power_off	= phy_meson_usb2_power_off,
>> +	.owner		= THIS_MODULE,
>> +};
>> +
>> +static int phy_meson_usb2_probe(struct platform_device *pdev)
>> +{
>> +	struct phy_meson_usb2_priv *priv;
>> +	struct resource *res;
>> +	struct phy *phy;
>> +	struct phy_provider *phy_provider;
>> +	int ret;
>> +
>> +	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
>> +	if (!priv)
>> +		return -ENOMEM;
>> +
>> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +	priv->regs = devm_ioremap_resource(&pdev->dev, res);
>> +	if (IS_ERR(priv->regs))
>> +		return PTR_ERR(priv->regs);
>> +
>> +	priv->clk_usb_general = devm_clk_get(&pdev->dev, "usb_general");
>> +	if (IS_ERR(priv->clk_usb_general))
>> +		return PTR_ERR(priv->clk_usb_general);
>> +
>> +	priv->clk_usb = devm_clk_get(&pdev->dev, "usb");
>> +	if (IS_ERR(priv->clk_usb))
>> +		return PTR_ERR(priv->clk_usb);
>> +
>> +	priv->dr_mode = of_usb_get_dr_mode_by_phy(pdev->dev.of_node, -1);
>> +	if (priv->dr_mode == USB_DR_MODE_UNKNOWN) {
>> +		dev_err(&pdev->dev,
>> +			"missing dual role configuration of the controller\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	phy = devm_phy_create(&pdev->dev, NULL, &phy_meson_usb2_ops);
>> +	if (IS_ERR(phy)) {
>> +		dev_err(&pdev->dev, "failed to create PHY\n");
>> +		return PTR_ERR(phy);
>> +	}
>> +
>> +	/*
>> +	 * No actual error check here because the hardware only has one reset
>> +	 * line for both PHYs. Using a shared reset is not possible because we
>> +	 * must call reset_control_reset to trigger the reset (which is not
>> +	 * allowed for shared resets in the reset framework).
>> +	 */
>> +	ret = device_reset_optional(&pdev->dev);
>> +	if (ret == -EPROBE_DEFER)
>> +		return ret;
>> +
>> +	phy_set_drvdata(phy, priv);
>> +
>> +	phy_provider =
>> +		devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
>> +
>> +	return PTR_ERR_OR_ZERO(phy_provider);
>> +}
>> +
>> +static const struct of_device_id phy_meson_usb2_of_match[] = {
>> +	{ .compatible = "amlogic,meson8b-usb2-phy", },
>> +	{ .compatible = "amlogic,meson-gxbb-usb2-phy", },
>> +	{ },
>> +};
>> +MODULE_DEVICE_TABLE(of, phy_meson_usb2_of_match);
>> +
>> +static struct platform_driver phy_meson_usb2_driver = {
>> +	.probe	= phy_meson_usb2_probe,
>> +	.driver	= {
>> +		.name		= "phy-meson-usb2",
>> +		.of_match_table	= phy_meson_usb2_of_match,
>> +	},
>> +};
>> +module_platform_driver(phy_meson_usb2_driver);
>> +
>> +MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
>> +MODULE_DESCRIPTION("Meson USB2 PHY driver");
>> +MODULE_LICENSE("GPL");
Kevin Hilman Sept. 19, 2016, 4:42 p.m. UTC | #4 
Kishon Vijay Abraham I <kishon@ti.com> writes:

> Hi Kevin,
>
> On Wednesday 14 September 2016 09:36 PM, Kevin Hilman wrote:
>> Kishon,
>> 
>> Martin Blumenstingl <martin.blumenstingl@googlemail.com> writes:
>> 
>>> This is a new driver for the USB PHY found in Meson8b and GXBB SoCs.
>>>
>>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>>> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
>>> Tested-by: Kevin Hilman <khilman@baylibre.com>
>> 
>> Will you be picking this up for v4.9?
>
> It's already late for 4.9. Generally send pull request to Greg around -rc6.
> This can go only in 4.10.

That's fine.

Does that mean you have it queued someplace?  I don't see it in any of
your branches.

Kevin
Kishon Vijay Abraham I Sept. 20, 2016, 5:01 a.m. UTC | #5 
On Monday 19 September 2016 10:12 PM, Kevin Hilman wrote:
> Kishon Vijay Abraham I <kishon@ti.com> writes:
> 
>> Hi Kevin,
>>
>> On Wednesday 14 September 2016 09:36 PM, Kevin Hilman wrote:
>>> Kishon,
>>>
>>> Martin Blumenstingl <martin.blumenstingl@googlemail.com> writes:
>>>
>>>> This is a new driver for the USB PHY found in Meson8b and GXBB SoCs.
>>>>
>>>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>>>> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
>>>> Tested-by: Kevin Hilman <khilman@baylibre.com>
>>>
>>> Will you be picking this up for v4.9?
>>
>> It's already late for 4.9. Generally send pull request to Greg around -rc6.
>> This can go only in 4.10.
> 
> That's fine.
> 
> Does that mean you have it queued someplace?  I don't see it in any of
> your branches.

I haven't queued so far. I'll create a testing branch to queue pending patches.

Thanks
Kishon
diff mbox

Patch

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 19bff3a..6ad87ec 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -453,4 +453,15 @@  config PHY_NS2_PCIE
 	help
 	  Enable this to support the Broadcom Northstar2 PCIe PHY.
 	  If unsure, say N.
+
+config PHY_MESON_USB2
+	tristate "Meson USB2 PHY driver"
+	default ARCH_MESON
+	depends on OF && (ARCH_MESON || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Enable this to support the Meson USB2 PHYs found in Meson8b
+	  and GXBB SoCs.
+	  If unsure, say N.
+
 endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 90ae198..dd507ac 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -56,3 +56,4 @@  obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
 obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o
 obj-$(CONFIG_ARCH_TEGRA) += tegra/
 obj-$(CONFIG_PHY_NS2_PCIE)		+= phy-bcm-ns2-pcie.o
+obj-$(CONFIG_PHY_MESON_USB2)		+= phy-meson-usb2.o
diff --git a/drivers/phy/phy-meson-usb2.c b/drivers/phy/phy-meson-usb2.c
new file mode 100644
index 0000000..eece521
--- /dev/null
+++ b/drivers/phy/phy-meson-usb2.c
@@ -0,0 +1,280 @@ 
+/*
+ * Meson USB2 PHY driver
+ *
+ * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/reset.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/usb/of.h>
+
+#define REG_CONFIG					0x00
+	#define REG_CONFIG_CLK_EN			BIT(0)
+	#define REG_CONFIG_CLK_SEL_MASK			GENMASK(3, 1)
+	#define REG_CONFIG_CLK_DIV_MASK			GENMASK(10, 4)
+	#define REG_CONFIG_CLK_32k_ALTSEL		BIT(15)
+	#define REG_CONFIG_TEST_TRIG			BIT(31)
+
+#define REG_CTRL					0x04
+	#define REG_CTRL_SOFT_PRST			BIT(0)
+	#define REG_CTRL_SOFT_HRESET			BIT(1)
+	#define REG_CTRL_SS_SCALEDOWN_MODE_MASK		GENMASK(3, 2)
+	#define REG_CTRL_CLK_DET_RST			BIT(4)
+	#define REG_CTRL_INTR_SEL			BIT(5)
+	#define REG_CTRL_CLK_DETECTED			BIT(8)
+	#define REG_CTRL_SOF_SENT_RCVD_TGL		BIT(9)
+	#define REG_CTRL_SOF_TOGGLE_OUT			BIT(10)
+	#define REG_CTRL_POWER_ON_RESET			BIT(15)
+	#define REG_CTRL_SLEEPM				BIT(16)
+	#define REG_CTRL_TX_BITSTUFF_ENN_H		BIT(17)
+	#define REG_CTRL_TX_BITSTUFF_ENN		BIT(18)
+	#define REG_CTRL_COMMON_ON			BIT(19)
+	#define REG_CTRL_REF_CLK_SEL_MASK		GENMASK(21, 20)
+	#define REG_CTRL_REF_CLK_SEL_SHIFT		20
+	#define REG_CTRL_FSEL_MASK			GENMASK(24, 22)
+	#define REG_CTRL_FSEL_SHIFT			22
+	#define REG_CTRL_PORT_RESET			BIT(25)
+	#define REG_CTRL_THREAD_ID_MASK			GENMASK(31, 26)
+
+#define REG_ENDP_INTR					0x08
+
+/* bits [31:26], [24:21] and [15:3] seem to be read-only */
+#define REG_ADP_BC					0x0c
+	#define REG_ADP_BC_VBUS_VLD_EXT_SEL		BIT(0)
+	#define REG_ADP_BC_VBUS_VLD_EXT			BIT(1)
+	#define REG_ADP_BC_OTG_DISABLE			BIT(2)
+	#define REG_ADP_BC_ID_PULLUP			BIT(3)
+	#define REG_ADP_BC_DRV_VBUS			BIT(4)
+	#define REG_ADP_BC_ADP_PRB_EN			BIT(5)
+	#define REG_ADP_BC_ADP_DISCHARGE		BIT(6)
+	#define REG_ADP_BC_ADP_CHARGE			BIT(7)
+	#define REG_ADP_BC_SESS_END			BIT(8)
+	#define REG_ADP_BC_DEVICE_SESS_VLD		BIT(9)
+	#define REG_ADP_BC_B_VALID			BIT(10)
+	#define REG_ADP_BC_A_VALID			BIT(11)
+	#define REG_ADP_BC_ID_DIG			BIT(12)
+	#define REG_ADP_BC_VBUS_VALID			BIT(13)
+	#define REG_ADP_BC_ADP_PROBE			BIT(14)
+	#define REG_ADP_BC_ADP_SENSE			BIT(15)
+	#define REG_ADP_BC_ACA_ENABLE			BIT(16)
+	#define REG_ADP_BC_DCD_ENABLE			BIT(17)
+	#define REG_ADP_BC_VDAT_DET_EN_B		BIT(18)
+	#define REG_ADP_BC_VDAT_SRC_EN_B		BIT(19)
+	#define REG_ADP_BC_CHARGE_SEL			BIT(20)
+	#define REG_ADP_BC_CHARGE_DETECT		BIT(21)
+	#define REG_ADP_BC_ACA_PIN_RANGE_C		BIT(22)
+	#define REG_ADP_BC_ACA_PIN_RANGE_B		BIT(23)
+	#define REG_ADP_BC_ACA_PIN_RANGE_A		BIT(24)
+	#define REG_ADP_BC_ACA_PIN_GND			BIT(25)
+	#define REG_ADP_BC_ACA_PIN_FLOAT		BIT(26)
+
+#define REG_DBG_UART					0x14
+
+#define REG_TEST					0x18
+	#define REG_TEST_DATA_IN_MASK			GENMASK(3, 0)
+	#define REG_TEST_EN_MASK			GENMASK(7, 4)
+	#define REG_TEST_ADDR_MASK			GENMASK(11, 8)
+	#define REG_TEST_DATA_OUT_SEL			BIT(12)
+	#define REG_TEST_CLK				BIT(13)
+	#define REG_TEST_VA_TEST_EN_B_MASK		GENMASK(15, 14)
+	#define REG_TEST_DATA_OUT_MASK			GENMASK(19, 16)
+	#define REG_TEST_DISABLE_ID_PULLUP		BIT(20)
+
+#define REG_TUNE					0x1c
+	#define REG_TUNE_TX_RES_TUNE_MASK		GENMASK(1, 0)
+	#define REG_TUNE_TX_HSXV_TUNE_MASK		GENMASK(3, 2)
+	#define REG_TUNE_TX_VREF_TUNE_MASK		GENMASK(7, 4)
+	#define REG_TUNE_TX_RISE_TUNE_MASK		GENMASK(9, 8)
+	#define REG_TUNE_TX_PREEMP_PULSE_TUNE		BIT(10)
+	#define REG_TUNE_TX_PREEMP_AMP_TUNE_MASK	GENMASK(12, 11)
+	#define REG_TUNE_TX_FSLS_TUNE_MASK		GENMASK(16, 13)
+	#define REG_TUNE_SQRX_TUNE_MASK			GENMASK(19, 17)
+	#define REG_TUNE_OTG_TUNE			GENMASK(22, 20)
+	#define REG_TUNE_COMP_DIS_TUNE			GENMASK(25, 23)
+	#define REG_TUNE_HOST_DM_PULLDOWN		BIT(26)
+	#define REG_TUNE_HOST_DP_PULLDOWN		BIT(27)
+
+#define RESET_COMPLETE_TIME				500
+#define ACA_ENABLE_COMPLETE_TIME			50
+
+struct phy_meson_usb2_priv {
+	void __iomem		*regs;
+	enum usb_dr_mode	dr_mode;
+	struct clk		*clk_usb_general;
+	struct clk		*clk_usb;
+};
+
+static u32 phy_meson_usb2_read(struct phy_meson_usb2_priv *phy_priv, u32 reg)
+{
+	return readl(phy_priv->regs + reg);
+}
+
+static void phy_meson_usb2_mask_bits(struct phy_meson_usb2_priv *phy_priv,
+				     u32 reg, u32 mask, u32 value)
+{
+	u32 data;
+
+	data = phy_meson_usb2_read(phy_priv, reg);
+	data &= ~mask;
+	data |= (value & mask);
+
+	writel(data, phy_priv->regs + reg);
+}
+
+static int phy_meson_usb2_power_on(struct phy *phy)
+{
+	struct phy_meson_usb2_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	ret = clk_prepare_enable(priv->clk_usb_general);
+	if (ret) {
+		dev_err(&phy->dev, "Failed to enable USB general clock\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(priv->clk_usb);
+	if (ret) {
+		dev_err(&phy->dev, "Failed to enable USB DDR clock\n");
+		return ret;
+	}
+
+	phy_meson_usb2_mask_bits(priv, REG_CONFIG, REG_CONFIG_CLK_32k_ALTSEL,
+				 REG_CONFIG_CLK_32k_ALTSEL);
+
+	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_REF_CLK_SEL_MASK,
+				 0x2 << REG_CTRL_REF_CLK_SEL_SHIFT);
+
+	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_FSEL_MASK,
+				 0x5 << REG_CTRL_FSEL_SHIFT);
+
+	/* reset the PHY */
+	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_POWER_ON_RESET,
+				 REG_CTRL_POWER_ON_RESET);
+	udelay(RESET_COMPLETE_TIME);
+	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_POWER_ON_RESET, 0);
+	udelay(RESET_COMPLETE_TIME);
+
+	phy_meson_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_SOF_TOGGLE_OUT,
+				 REG_CTRL_SOF_TOGGLE_OUT);
+
+	if (priv->dr_mode == USB_DR_MODE_HOST) {
+		phy_meson_usb2_mask_bits(priv, REG_ADP_BC,
+					 REG_ADP_BC_ACA_ENABLE,
+					 REG_ADP_BC_ACA_ENABLE);
+
+		udelay(ACA_ENABLE_COMPLETE_TIME);
+
+		if (phy_meson_usb2_read(priv, REG_ADP_BC) &
+			REG_ADP_BC_ACA_PIN_FLOAT) {
+			dev_warn(&phy->dev, "USB ID detect failed!\n");
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static int phy_meson_usb2_power_off(struct phy *phy)
+{
+	struct phy_meson_usb2_priv *priv = phy_get_drvdata(phy);
+
+	clk_disable_unprepare(priv->clk_usb);
+	clk_disable_unprepare(priv->clk_usb_general);
+
+	return 0;
+}
+
+static const struct phy_ops phy_meson_usb2_ops = {
+	.power_on	= phy_meson_usb2_power_on,
+	.power_off	= phy_meson_usb2_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int phy_meson_usb2_probe(struct platform_device *pdev)
+{
+	struct phy_meson_usb2_priv *priv;
+	struct resource *res;
+	struct phy *phy;
+	struct phy_provider *phy_provider;
+	int ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->regs))
+		return PTR_ERR(priv->regs);
+
+	priv->clk_usb_general = devm_clk_get(&pdev->dev, "usb_general");
+	if (IS_ERR(priv->clk_usb_general))
+		return PTR_ERR(priv->clk_usb_general);
+
+	priv->clk_usb = devm_clk_get(&pdev->dev, "usb");
+	if (IS_ERR(priv->clk_usb))
+		return PTR_ERR(priv->clk_usb);
+
+	priv->dr_mode = of_usb_get_dr_mode_by_phy(pdev->dev.of_node, -1);
+	if (priv->dr_mode == USB_DR_MODE_UNKNOWN) {
+		dev_err(&pdev->dev,
+			"missing dual role configuration of the controller\n");
+		return -EINVAL;
+	}
+
+	phy = devm_phy_create(&pdev->dev, NULL, &phy_meson_usb2_ops);
+	if (IS_ERR(phy)) {
+		dev_err(&pdev->dev, "failed to create PHY\n");
+		return PTR_ERR(phy);
+	}
+
+	/*
+	 * No actual error check here because the hardware only has one reset
+	 * line for both PHYs. Using a shared reset is not possible because we
+	 * must call reset_control_reset to trigger the reset (which is not
+	 * allowed for shared resets in the reset framework).
+	 */
+	ret = device_reset_optional(&pdev->dev);
+	if (ret == -EPROBE_DEFER)
+		return ret;
+
+	phy_set_drvdata(phy, priv);
+
+	phy_provider =
+		devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id phy_meson_usb2_of_match[] = {
+	{ .compatible = "amlogic,meson8b-usb2-phy", },
+	{ .compatible = "amlogic,meson-gxbb-usb2-phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, phy_meson_usb2_of_match);
+
+static struct platform_driver phy_meson_usb2_driver = {
+	.probe	= phy_meson_usb2_probe,
+	.driver	= {
+		.name		= "phy-meson-usb2",
+		.of_match_table	= phy_meson_usb2_of_match,
+	},
+};
+module_platform_driver(phy_meson_usb2_driver);
+
+MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
+MODULE_DESCRIPTION("Meson USB2 PHY driver");
+MODULE_LICENSE("GPL");