| Message ID | 1488300022-30150-2-git-send-email-agust@denx.de (mailing list archive) |
|---|---|
| State | Accepted, archived |
| Headers | show |
On 28.2.2017 17:40, Anatolij Gustschin wrote: > Add dt binding documentation details for Xilinx FPGA configuration > over slave serial interface. > > Signed-off-by: Anatolij Gustschin <agust@denx.de> > Acked-by: Moritz Fischer <mdf@kernel.org> > Acked-by: Rob Herring <robh@kernel.org> > --- > Changes in v4: > > - add Acked-by tags > > Changes in v3: > > - extend example to show the usage in SPI master node, connected > to the fpga-region node > > Changes in v2: > > - correct gpios properties in example to match above description > > - use fpga-mgr@0 instead of fpga-spi@0 in example > > .../bindings/fpga/xilinx-slave-serial.txt | 44 ++++++++++++++++++++++ > 1 file changed, 44 insertions(+) > create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt > > diff --git a/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt b/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt > new file mode 100644 > index 0000000..9766f74 > --- /dev/null > +++ b/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt > @@ -0,0 +1,44 @@ > +Xilinx Slave Serial SPI FPGA Manager > + > +Xilinx Spartan-6 FPGAs support a method of loading the bitstream over > +what is referred to as "slave serial" interface. > +The slave serial link is not technically SPI, and might require extra > +circuits in order to play nicely with other SPI slaves on the same bus. > + > +See https://www.xilinx.com/support/documentation/user_guides/ug380.pdf > + > +Required properties: > +- compatible: should contain "xlnx,fpga-slave-serial" > +- reg: spi chip select of the FPGA > +- prog_b-gpios: config pin (referred to as PROGRAM_B in the manual) > +- done-gpios: config status pin (referred to as DONE in the manual) > + > +Example for full FPGA configuration: > + > + fpga-region0 { > + compatible = "fpga-region"; > + fpga-mgr = <&fpga_mgr_spi>; > + #address-cells = <0x1>; > + #size-cells = <0x1>; > + }; > + > + spi1: spi@10680 { > + compatible = "marvell,armada-xp-spi", "marvell,orion-spi"; > + pinctrl-0 = <&spi0_pins>; > + pinctrl-names = "default"; > + #address-cells = <1>; > + #size-cells = <0>; > + cell-index = <1>; > + interrupts = <92>; > + clocks = <&coreclk 0>; > + status = "okay"; > + > + fpga_mgr_spi: fpga-mgr@0 { > + compatible = "xlnx,fpga-slave-serial"; > + spi-max-frequency = <60000000>; > + spi-cpha; > + reg = <0>; > + done-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; > + prog_b-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; > + }; > + }; > Acked-by: Michal Simek <michal.simek@xilinx.com> Thanks, Michal
On Thu, Mar 16, 2017 at 6:01 AM, Michal Simek <monstr@monstr.eu> wrote: > On 28.2.2017 17:40, Anatolij Gustschin wrote: >> Add dt binding documentation details for Xilinx FPGA configuration >> over slave serial interface. >> >> Signed-off-by: Anatolij Gustschin <agust@denx.de> >> Acked-by: Moritz Fischer <mdf@kernel.org> >> Acked-by: Rob Herring <robh@kernel.org> >> --- >> Changes in v4: >> >> - add Acked-by tags >> >> Changes in v3: >> >> - extend example to show the usage in SPI master node, connected >> to the fpga-region node >> >> Changes in v2: >> >> - correct gpios properties in example to match above description >> >> - use fpga-mgr@0 instead of fpga-spi@0 in example >> >> .../bindings/fpga/xilinx-slave-serial.txt | 44 ++++++++++++++++++++++ >> 1 file changed, 44 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt >> >> diff --git a/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt b/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt >> new file mode 100644 >> index 0000000..9766f74 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt >> @@ -0,0 +1,44 @@ >> +Xilinx Slave Serial SPI FPGA Manager >> + >> +Xilinx Spartan-6 FPGAs support a method of loading the bitstream over >> +what is referred to as "slave serial" interface. >> +The slave serial link is not technically SPI, and might require extra >> +circuits in order to play nicely with other SPI slaves on the same bus. >> + >> +See https://www.xilinx.com/support/documentation/user_guides/ug380.pdf >> + >> +Required properties: >> +- compatible: should contain "xlnx,fpga-slave-serial" >> +- reg: spi chip select of the FPGA >> +- prog_b-gpios: config pin (referred to as PROGRAM_B in the manual) >> +- done-gpios: config status pin (referred to as DONE in the manual) >> + >> +Example for full FPGA configuration: >> + >> + fpga-region0 { >> + compatible = "fpga-region"; >> + fpga-mgr = <&fpga_mgr_spi>; >> + #address-cells = <0x1>; >> + #size-cells = <0x1>; >> + }; >> + >> + spi1: spi@10680 { >> + compatible = "marvell,armada-xp-spi", "marvell,orion-spi"; >> + pinctrl-0 = <&spi0_pins>; >> + pinctrl-names = "default"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + cell-index = <1>; >> + interrupts = <92>; >> + clocks = <&coreclk 0>; >> + status = "okay"; >> + >> + fpga_mgr_spi: fpga-mgr@0 { >> + compatible = "xlnx,fpga-slave-serial"; >> + spi-max-frequency = <60000000>; >> + spi-cpha; >> + reg = <0>; >> + done-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; >> + prog_b-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; >> + }; >> + }; >> > > Acked-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Alan Tull <atull@kernel.org> > > Thanks, > Michal > > -- > Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91 > w: www.monstr.eu p: +42-0-721842854 > Maintainer of Linux kernel - Xilinx Microblaze > Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP ARM64 SoCs > U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP SoCs > > -- To unsubscribe from this list: send the line "unsubscribe linux-fpga" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt b/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt new file mode 100644 index 0000000..9766f74 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt @@ -0,0 +1,44 @@ +Xilinx Slave Serial SPI FPGA Manager + +Xilinx Spartan-6 FPGAs support a method of loading the bitstream over +what is referred to as "slave serial" interface. +The slave serial link is not technically SPI, and might require extra +circuits in order to play nicely with other SPI slaves on the same bus. + +See https://www.xilinx.com/support/documentation/user_guides/ug380.pdf + +Required properties: +- compatible: should contain "xlnx,fpga-slave-serial" +- reg: spi chip select of the FPGA +- prog_b-gpios: config pin (referred to as PROGRAM_B in the manual) +- done-gpios: config status pin (referred to as DONE in the manual) + +Example for full FPGA configuration: + + fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr_spi>; + #address-cells = <0x1>; + #size-cells = <0x1>; + }; + + spi1: spi@10680 { + compatible = "marvell,armada-xp-spi", "marvell,orion-spi"; + pinctrl-0 = <&spi0_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + interrupts = <92>; + clocks = <&coreclk 0>; + status = "okay"; + + fpga_mgr_spi: fpga-mgr@0 { + compatible = "xlnx,fpga-slave-serial"; + spi-max-frequency = <60000000>; + spi-cpha; + reg = <0>; + done-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; + prog_b-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + }; + };