| Message ID | 1502475835-54818-1-git-send-email-srinivas.pandruvada@linux.intel.com (mailing list archive) |
|---|---|
| State | Changes Requested, archived |
| Headers | show |
On Friday, August 11, 2017 8:23:55 PM CEST Srinivas Pandruvada wrote: > For SoC to achieve its lowest power platform idle state a set of hardware > preconditions must be met. These preconditions or constraints can be > obtained by issuing a device specific method (_DSM) with function "1". > Refer to the document provided in the link below. > > Here during initialization (from attach() callback of LPS0 device), invoke > function 1 to get the device constraints. Each enabled constraint is > stored in a table. > > The devices in this table are used to check whether they were in required > minimum state, while entering suspend. This check is done from platform > freeze wake() callback, only when /sys/power/pm_debug_messages attribute > is non zero. > > If any constraint is not met and device is ACPI power managed then it > prints the device name to kernel logs. > > Also if debug is enabled in acpi/sleep.c, the constraint table and state > of each device on wake is dumped in kernel logs. > > Since pm_debug_messages_on setting is used as condition to check > constraints outside kernel/power/main.c, pm_debug_messages_on is changed > to a global variable. > > Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf > Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> > --- > > v3 > - Removed the patch 0001 for exporting pm_debug_messages_on via a function. > As suggested by Rafael, made the pm_debug_messages_on a global variable instead. > - Moved the constraint check outside if() block and valid for all calls to > acpi_freeze_wakeup() > - Dumping irrespective of return value of acpi_device_get_power(). > - Rebased to linux-next as of today > > v2 > - Changes as suggested by Lukas Wunner. > - Using pm_debug_messages_on attribute to prevent constraints check to > save some cycles on wake. > > drivers/acpi/sleep.c | 169 ++++++++++++++++++++++++++++++++++++++++++++++++ > include/linux/suspend.h | 2 + > kernel/power/main.c | 2 +- > 3 files changed, 172 insertions(+), 1 deletion(-) > > diff --git a/drivers/acpi/sleep.c b/drivers/acpi/sleep.c > index 0a16435..df513e7 100644 > --- a/drivers/acpi/sleep.c > +++ b/drivers/acpi/sleep.c > @@ -669,6 +669,7 @@ static const struct acpi_device_id lps0_device_ids[] = { > > #define ACPI_LPS0_DSM_UUID "c4eb40a0-6cd2-11e2-bcfd-0800200c9a66" > > +#define ACPI_LPS0_GET_DEVICE_CONSTRAINTS 1 > #define ACPI_LPS0_SCREEN_OFF 3 > #define ACPI_LPS0_SCREEN_ON 4 > #define ACPI_LPS0_ENTRY 5 > @@ -680,6 +681,167 @@ static acpi_handle lps0_device_handle; > static guid_t lps0_dsm_guid; > static char lps0_dsm_func_mask; > > +/* Device constraint entry structure */ > +struct lpi_device_info { > + char *name; > + int enabled; > + union acpi_object *package; > +}; > + > +/* Constraint package structure */ > +struct lpi_device_constraint { > + int uid; > + int min_dstate; > + int function_states; > +}; > + > +struct lpi_constraints { > + char *name; > + int min_dstate; If you store the handle here as well, you won't need to look it up every time _check_constraints() is called. > +}; > + > +static struct lpi_constraints *lpi_constraints_table; > +static int lpi_constraints_table_size; > + > +static void lpi_device_get_constraints(void) > +{ > + union acpi_object *out_obj; > + int i; > + > + out_obj = acpi_evaluate_dsm_typed(lps0_device_handle, &lps0_dsm_guid, > + 1, ACPI_LPS0_GET_DEVICE_CONSTRAINTS, > + NULL, ACPI_TYPE_PACKAGE); > + > + acpi_handle_debug(lps0_device_handle, "_DSM function 1 eval %s\n", > + out_obj ? "successful" : "failed"); > + > + if (!out_obj) > + return; > + > + lpi_constraints_table = kcalloc(out_obj->package.count, > + sizeof(*lpi_constraints_table), > + GFP_KERNEL); > + if (!lpi_constraints_table) > + goto free_acpi_buffer; > + > + pr_debug("LPI: constraints dump begin\n"); Please add an empty line after this. Also something like "constraints list begin" would sound better IMO. > + for (i = 0; i < out_obj->package.count; i++) { > + union acpi_object *package = &out_obj->package.elements[i]; > + struct lpi_device_info info = { }; > + int package_count = 0, j; > + > + if (!package) > + continue; > + > + for (j = 0; j < package->package.count; ++j) { > + union acpi_object *element = > + &(package->package.elements[j]); > + > + switch (element->type) { > + case ACPI_TYPE_INTEGER: > + info.enabled = element->integer.value; > + break; > + case ACPI_TYPE_STRING: > + info.name = element->string.pointer; > + break; > + case ACPI_TYPE_PACKAGE: > + package_count = element->package.count; > + info.package = element->package.elements; > + break; > + } > + } > + > + if (!info.enabled || !info.package || !info.name) > + continue; > + I would evaluate acpi_get_handle() here and store the handle in the constraints table (if persent). And you can skip the entry altogether if not present, because you won't be printing it anyway. > + lpi_constraints_table[lpi_constraints_table_size].name = > + kstrdup(info.name, GFP_KERNEL); > + if (!lpi_constraints_table[lpi_constraints_table_size].name) > + goto free_constraints; > + > + pr_debug("index:%d Name:%s\n", i, info.name); > + > + for (j = 0; j < package_count; ++j) { > + union acpi_object *info_obj = &info.package[j]; > + union acpi_object *cnstr_pkg; > + union acpi_object *obj; > + struct lpi_device_constraint dev_info; > + > + switch (info_obj->type) { > + case ACPI_TYPE_INTEGER: > + /* version */ > + break; > + case ACPI_TYPE_PACKAGE: > + if (info_obj->package.count < 2) > + break; > + > + cnstr_pkg = info_obj->package.elements; > + obj = &cnstr_pkg[0]; > + dev_info.uid = obj->integer.value; > + obj = &cnstr_pkg[1]; > + dev_info.min_dstate = obj->integer.value; > + pr_debug("uid %d min_dstate %d\n", > + dev_info.uid, > + dev_info.min_dstate); > + lpi_constraints_table[ > + lpi_constraints_table_size].min_dstate = > + dev_info.min_dstate; > + break; > + } > + } > + > + lpi_constraints_table_size++; > + } > + > + pr_debug("LPI: constraints dump end\n"); > +free_acpi_buffer: > + ACPI_FREE(out_obj); > + return; > + > +free_constraints: > + ACPI_FREE(out_obj); > + for (i = 0; i < lpi_constraints_table_size; ++i) > + kfree(lpi_constraints_table[i].name); > + kfree(lpi_constraints_table); > + lpi_constraints_table_size = 0; > +} > + > +static void lpi_check_constraints(void) > +{ > + int i; > + > + for (i = 0; i < lpi_constraints_table_size; ++i) { > + acpi_handle handle; > + struct acpi_device *adev; > + int state, ret; > + > + if (ACPI_FAILURE(acpi_get_handle(NULL, > + lpi_constraints_table[i].name, > + &handle))) > + continue; So if you store the handle, the above won't be necessary. > + > + if (acpi_bus_get_device(handle, &adev)) > + continue; > + > + ret = acpi_device_get_power(adev, &state); > + if (ret) > + pr_debug("LPI: %s required min power state %d, current power state %d, real power state [ERROR]\n", > + lpi_constraints_table[i].name, > + lpi_constraints_table[i].min_dstate, > + adev->power.state); > + else > + pr_debug("LPI: %s required min power state %d, current power state %d, real power state %d\n", > + lpi_constraints_table[i].name, > + lpi_constraints_table[i].min_dstate, > + adev->power.state, state); I'm not convinced about the value of the above TBH. Also in theory _PSC may go and access things like PCI config spaces of devices which isn't a good idea for devices in D3_cold, so maybe skip this? > + > + if (adev->flags.power_manageable && adev->power.state < > + lpi_constraints_table[i].min_dstate) > + pr_info("LPI: Constraint [%s] not matched\n", "Constrant [%s] not met"? Also I'd use acpi_handle_info(adev->handle, ...) to print this. > + lpi_constraints_table[i].name); I would print a message if !flags.power_manageable, because it means we can't get the constraint right in general. Also I would print both power.state and min_state (possibly using acpi_power_state_string()) in this message as that is valuable for debugging. Thanks, Rafael
On Sat, 2017-08-12 at 16:27 +0200, Rafael J. Wysocki wrote: [...] > > + > > +struct lpi_constraints { > > + char *name; > > + int min_dstate; > If you store the handle here as well, you won't need to > look it up every time _check_constraints() is called. The reason I didn't keep handle here, I thought handle can be stale or change for PnP device on plug in and out. Is this not true? > > > > +}; > > + > > +static struct lpi_constraints *lpi_constraints_table; > > +static int lpi_constraints_table_size; > > + > > +static void lpi_device_get_constraints(void) > > +{ > > + union acpi_object *out_obj; > > + int i; > > + > > + out_obj = acpi_evaluate_dsm_typed(lps0_device_handle, > > &lps0_dsm_guid, > > + 1, > > ACPI_LPS0_GET_DEVICE_CONSTRAINTS, > > + NULL, > > ACPI_TYPE_PACKAGE); > > + > > + acpi_handle_debug(lps0_device_handle, "_DSM function 1 > > eval %s\n", > > + out_obj ? "successful" : "failed"); > > + > > + if (!out_obj) > > + return; > > + > > + lpi_constraints_table = kcalloc(out_obj->package.count, > > + sizeof(*lpi_constraints_ta > > ble), > > + GFP_KERNEL); > > + if (!lpi_constraints_table) > > + goto free_acpi_buffer; > > + > > + pr_debug("LPI: constraints dump begin\n"); > Please add an empty line after this. Also something like > "constraints > list begin" would sound better IMO. > OK. > > > > + for (i = 0; i < out_obj->package.count; i++) { > > + union acpi_object *package = &out_obj- > > >package.elements[i]; > > + struct lpi_device_info info = { }; > > + int package_count = 0, j; > > + > > + if (!package) > > + continue; > > + > > + for (j = 0; j < package->package.count; ++j) { > > + union acpi_object *element = > > + &(package- > > >package.elements[j]); > > + > > + switch (element->type) { > > + case ACPI_TYPE_INTEGER: > > + info.enabled = element- > > >integer.value; > > + break; > > + case ACPI_TYPE_STRING: > > + info.name = element- > > >string.pointer; > > + break; > > + case ACPI_TYPE_PACKAGE: > > + package_count = element- > > >package.count; > > + info.package = element- > > >package.elements; > > + break; > > + } > > + } > > + > > + if (!info.enabled || !info.package || !info.name) > > + continue; > > + > I would evaluate acpi_get_handle() here and store the handle in the > constraints table (if persent). And you can skip the entry > altogether > if not present, because you won't be printing it anyway. > > > > > + lpi_constraints_table[lpi_constraints_table_size]. > > name = > > + kstrdup(info.name, > > GFP_KERNEL); > > + if > > (!lpi_constraints_table[lpi_constraints_table_size].name) > > + goto free_constraints; > > + > > + pr_debug("index:%d Name:%s\n", i, info.name); > > + > > + for (j = 0; j < package_count; ++j) { > > + union acpi_object *info_obj = > > &info.package[j]; > > + union acpi_object *cnstr_pkg; > > + union acpi_object *obj; > > + struct lpi_device_constraint dev_info; > > + > > + switch (info_obj->type) { > > + case ACPI_TYPE_INTEGER: > > + /* version */ > > + break; > > + case ACPI_TYPE_PACKAGE: > > + if (info_obj->package.count < 2) > > + break; > > + > > + cnstr_pkg = info_obj- > > >package.elements; > > + obj = &cnstr_pkg[0]; > > + dev_info.uid = obj->integer.value; > > + obj = &cnstr_pkg[1]; > > + dev_info.min_dstate = obj- > > >integer.value; > > + pr_debug("uid %d min_dstate %d\n", > > + dev_info.uid, > > + dev_info.min_dstate); > > + lpi_constraints_table[ > > + lpi_constraints_table_size > > ].min_dstate = > > + dev_info.min_dstat > > e; > > + break; > > + } > > + } > > + > > + lpi_constraints_table_size++; > > + } > > + > > + pr_debug("LPI: constraints dump end\n"); > > +free_acpi_buffer: > > + ACPI_FREE(out_obj); > > + return; > > + > > +free_constraints: > > + ACPI_FREE(out_obj); > > + for (i = 0; i < lpi_constraints_table_size; ++i) > > + kfree(lpi_constraints_table[i].name); > > + kfree(lpi_constraints_table); > > + lpi_constraints_table_size = 0; > > +} > > + > > +static void lpi_check_constraints(void) > > +{ > > + int i; > > + > > + for (i = 0; i < lpi_constraints_table_size; ++i) { > > + acpi_handle handle; > > + struct acpi_device *adev; > > + int state, ret; > > + > > + if (ACPI_FAILURE(acpi_get_handle(NULL, > > + lpi_constraints_t > > able[i].name, > > + &handle))) > > + continue; > So if you store the handle, the above won't be necessary. > > > > > + > > + if (acpi_bus_get_device(handle, &adev)) > > + continue; > > + > > + ret = acpi_device_get_power(adev, &state); > > + if (ret) > > + pr_debug("LPI: %s required min power state > > %d, current power state %d, real power state [ERROR]\n", > > + lpi_constraints_table[i].name, > > + lpi_constraints_table[i].min_dsta > > te, > > + adev->power.state); > > + else > > + pr_debug("LPI: %s required min power state > > %d, current power state %d, real power state %d\n", > > + lpi_constraints_table[i].name, > > + lpi_constraints_table[i].min_dsta > > te, > > + adev->power.state, state); > I'm not convinced about the value of the above TBH. > > Also in theory _PSC may go and access things like PCI config spaces > of devices > which isn't a good idea for devices in D3_cold, so maybe skip this? OK. > > > > > + > > + if (adev->flags.power_manageable && adev- > > >power.state < > > + lpi_constraints_table[i].m > > in_dstate) > > + pr_info("LPI: Constraint [%s] not > > matched\n", > "Constrant [%s] not met"? > > Also I'd use acpi_handle_info(adev->handle, ...) to print this. > > > > > + lpi_constraints_table[i].name); > I would print a message if !flags.power_manageable, because it means > we > can't get the constraint right in general. > > Also I would print both power.state and min_state (possibly using > acpi_power_state_string()) in this message as that is valuable for > debugging. OK. Thanks, Srinivas
On Sat, Aug 12, 2017 at 5:59 PM, Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> wrote: > On Sat, 2017-08-12 at 16:27 +0200, Rafael J. Wysocki wrote: > [...] > >> > + >> > +struct lpi_constraints { >> > + char *name; >> > + int min_dstate; >> If you store the handle here as well, you won't need to >> look it up every time _check_constraints() is called. > > The reason I didn't keep handle here, I thought handle can be stale or > change for PnP device on plug in and out. Is this not true? The handles don't go away on hot remove as a rule. That may only happen if tables get unloaded, but basically the constraints should not point to anything in a table that may go away.
On Sun, 2017-08-13 at 00:37 +0200, Rafael J. Wysocki wrote: > On Sat, Aug 12, 2017 at 5:59 PM, Srinivas Pandruvada > <srinivas.pandruvada@linux.intel.com> wrote: > > > > On Sat, 2017-08-12 at 16:27 +0200, Rafael J. Wysocki wrote: > > [...] > > > > > > > > > > > > > + > > > > +struct lpi_constraints { > > > > + char *name; > > > > + int min_dstate; > > > If you store the handle here as well, you won't need to > > > look it up every time _check_constraints() is called. > > The reason I didn't keep handle here, I thought handle can be stale > > or > > change for PnP device on plug in and out. Is this not true? > The handles don't go away on hot remove as a rule. That may only > happen if tables get unloaded, but basically the constraints should > not point to anything in a table that may go away. So we don't need to worry about this case where tables gets unloaded and replaced? This is in a debug path, so additional overhead of path to handle conversion may not be significant. Thanks, Srinivas
On Sun, Aug 13, 2017 at 2:00 AM, Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> wrote: > On Sun, 2017-08-13 at 00:37 +0200, Rafael J. Wysocki wrote: >> On Sat, Aug 12, 2017 at 5:59 PM, Srinivas Pandruvada >> <srinivas.pandruvada@linux.intel.com> wrote: >> > >> > On Sat, 2017-08-12 at 16:27 +0200, Rafael J. Wysocki wrote: >> > [...] >> > >> > > >> > > > >> > > > + >> > > > +struct lpi_constraints { >> > > > + char *name; >> > > > + int min_dstate; >> > > If you store the handle here as well, you won't need to >> > > look it up every time _check_constraints() is called. >> > The reason I didn't keep handle here, I thought handle can be stale >> > or >> > change for PnP device on plug in and out. Is this not true? >> The handles don't go away on hot remove as a rule. That may only >> happen if tables get unloaded, but basically the constraints should >> not point to anything in a table that may go away. > > So we don't need to worry about this case where tables gets unloaded > and replaced? I wouldn't. :-) We generally don't support that case entirely, so why bother? > This is in a debug path, so additional overhead of path > to handle conversion may not be significant. Well, it still is wasted cycles ...
diff --git a/drivers/acpi/sleep.c b/drivers/acpi/sleep.c index 0a16435..df513e7 100644 --- a/drivers/acpi/sleep.c +++ b/drivers/acpi/sleep.c @@ -669,6 +669,7 @@ static const struct acpi_device_id lps0_device_ids[] = { #define ACPI_LPS0_DSM_UUID "c4eb40a0-6cd2-11e2-bcfd-0800200c9a66" +#define ACPI_LPS0_GET_DEVICE_CONSTRAINTS 1 #define ACPI_LPS0_SCREEN_OFF 3 #define ACPI_LPS0_SCREEN_ON 4 #define ACPI_LPS0_ENTRY 5 @@ -680,6 +681,167 @@ static acpi_handle lps0_device_handle; static guid_t lps0_dsm_guid; static char lps0_dsm_func_mask; +/* Device constraint entry structure */ +struct lpi_device_info { + char *name; + int enabled; + union acpi_object *package; +}; + +/* Constraint package structure */ +struct lpi_device_constraint { + int uid; + int min_dstate; + int function_states; +}; + +struct lpi_constraints { + char *name; + int min_dstate; +}; + +static struct lpi_constraints *lpi_constraints_table; +static int lpi_constraints_table_size; + +static void lpi_device_get_constraints(void) +{ + union acpi_object *out_obj; + int i; + + out_obj = acpi_evaluate_dsm_typed(lps0_device_handle, &lps0_dsm_guid, + 1, ACPI_LPS0_GET_DEVICE_CONSTRAINTS, + NULL, ACPI_TYPE_PACKAGE); + + acpi_handle_debug(lps0_device_handle, "_DSM function 1 eval %s\n", + out_obj ? "successful" : "failed"); + + if (!out_obj) + return; + + lpi_constraints_table = kcalloc(out_obj->package.count, + sizeof(*lpi_constraints_table), + GFP_KERNEL); + if (!lpi_constraints_table) + goto free_acpi_buffer; + + pr_debug("LPI: constraints dump begin\n"); + for (i = 0; i < out_obj->package.count; i++) { + union acpi_object *package = &out_obj->package.elements[i]; + struct lpi_device_info info = { }; + int package_count = 0, j; + + if (!package) + continue; + + for (j = 0; j < package->package.count; ++j) { + union acpi_object *element = + &(package->package.elements[j]); + + switch (element->type) { + case ACPI_TYPE_INTEGER: + info.enabled = element->integer.value; + break; + case ACPI_TYPE_STRING: + info.name = element->string.pointer; + break; + case ACPI_TYPE_PACKAGE: + package_count = element->package.count; + info.package = element->package.elements; + break; + } + } + + if (!info.enabled || !info.package || !info.name) + continue; + + lpi_constraints_table[lpi_constraints_table_size].name = + kstrdup(info.name, GFP_KERNEL); + if (!lpi_constraints_table[lpi_constraints_table_size].name) + goto free_constraints; + + pr_debug("index:%d Name:%s\n", i, info.name); + + for (j = 0; j < package_count; ++j) { + union acpi_object *info_obj = &info.package[j]; + union acpi_object *cnstr_pkg; + union acpi_object *obj; + struct lpi_device_constraint dev_info; + + switch (info_obj->type) { + case ACPI_TYPE_INTEGER: + /* version */ + break; + case ACPI_TYPE_PACKAGE: + if (info_obj->package.count < 2) + break; + + cnstr_pkg = info_obj->package.elements; + obj = &cnstr_pkg[0]; + dev_info.uid = obj->integer.value; + obj = &cnstr_pkg[1]; + dev_info.min_dstate = obj->integer.value; + pr_debug("uid %d min_dstate %d\n", + dev_info.uid, + dev_info.min_dstate); + lpi_constraints_table[ + lpi_constraints_table_size].min_dstate = + dev_info.min_dstate; + break; + } + } + + lpi_constraints_table_size++; + } + + pr_debug("LPI: constraints dump end\n"); +free_acpi_buffer: + ACPI_FREE(out_obj); + return; + +free_constraints: + ACPI_FREE(out_obj); + for (i = 0; i < lpi_constraints_table_size; ++i) + kfree(lpi_constraints_table[i].name); + kfree(lpi_constraints_table); + lpi_constraints_table_size = 0; +} + +static void lpi_check_constraints(void) +{ + int i; + + for (i = 0; i < lpi_constraints_table_size; ++i) { + acpi_handle handle; + struct acpi_device *adev; + int state, ret; + + if (ACPI_FAILURE(acpi_get_handle(NULL, + lpi_constraints_table[i].name, + &handle))) + continue; + + if (acpi_bus_get_device(handle, &adev)) + continue; + + ret = acpi_device_get_power(adev, &state); + if (ret) + pr_debug("LPI: %s required min power state %d, current power state %d, real power state [ERROR]\n", + lpi_constraints_table[i].name, + lpi_constraints_table[i].min_dstate, + adev->power.state); + else + pr_debug("LPI: %s required min power state %d, current power state %d, real power state %d\n", + lpi_constraints_table[i].name, + lpi_constraints_table[i].min_dstate, + adev->power.state, state); + + if (adev->flags.power_manageable && adev->power.state < + lpi_constraints_table[i].min_dstate) + pr_info("LPI: Constraint [%s] not matched\n", + lpi_constraints_table[i].name); + } +} + static void acpi_sleep_run_lps0_dsm(unsigned int func) { union acpi_object *out_obj; @@ -729,6 +891,9 @@ static int lps0_device_attach(struct acpi_device *adev, "_DSM function 0 evaluation failed\n"); } ACPI_FREE(out_obj); + + lpi_device_get_constraints(); + return 0; } @@ -766,6 +931,10 @@ static int acpi_freeze_prepare(void) static void acpi_freeze_wake(void) { + + if (pm_debug_messages_on) + lpi_check_constraints(); + /* * If IRQD_WAKEUP_ARMED is not set for the SCI at this point, it means * that the SCI has triggered while suspended, so cancel the wakeup in diff --git a/include/linux/suspend.h b/include/linux/suspend.h index 8c3b0b1..126adcb 100644 --- a/include/linux/suspend.h +++ b/include/linux/suspend.h @@ -495,9 +495,11 @@ static inline void unlock_system_sleep(void) {} #ifdef CONFIG_PM_SLEEP_DEBUG extern bool pm_print_times_enabled; +extern bool pm_debug_messages_on; extern __printf(2, 3) void __pm_pr_dbg(bool defer, const char *fmt, ...); #else #define pm_print_times_enabled (false) +#define pm_debug_messages_on (false) #include <linux/printk.h> diff --git a/kernel/power/main.c b/kernel/power/main.c index 3074ea4..3a2ca90 100644 --- a/kernel/power/main.c +++ b/kernel/power/main.c @@ -361,7 +361,7 @@ static ssize_t pm_wakeup_irq_show(struct kobject *kobj, power_attr_ro(pm_wakeup_irq); -static bool pm_debug_messages_on __read_mostly; +bool pm_debug_messages_on __read_mostly; static ssize_t pm_debug_messages_show(struct kobject *kobj, struct kobj_attribute *attr, char *buf)
For SoC to achieve its lowest power platform idle state a set of hardware preconditions must be met. These preconditions or constraints can be obtained by issuing a device specific method (_DSM) with function "1". Refer to the document provided in the link below. Here during initialization (from attach() callback of LPS0 device), invoke function 1 to get the device constraints. Each enabled constraint is stored in a table. The devices in this table are used to check whether they were in required minimum state, while entering suspend. This check is done from platform freeze wake() callback, only when /sys/power/pm_debug_messages attribute is non zero. If any constraint is not met and device is ACPI power managed then it prints the device name to kernel logs. Also if debug is enabled in acpi/sleep.c, the constraint table and state of each device on wake is dumped in kernel logs. Since pm_debug_messages_on setting is used as condition to check constraints outside kernel/power/main.c, pm_debug_messages_on is changed to a global variable. Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> --- v3 - Removed the patch 0001 for exporting pm_debug_messages_on via a function. As suggested by Rafael, made the pm_debug_messages_on a global variable instead. - Moved the constraint check outside if() block and valid for all calls to acpi_freeze_wakeup() - Dumping irrespective of return value of acpi_device_get_power(). - Rebased to linux-next as of today v2 - Changes as suggested by Lukas Wunner. - Using pm_debug_messages_on attribute to prevent constraints check to save some cycles on wake. drivers/acpi/sleep.c | 169 ++++++++++++++++++++++++++++++++++++++++++++++++ include/linux/suspend.h | 2 + kernel/power/main.c | 2 +- 3 files changed, 172 insertions(+), 1 deletion(-)