@@ -196,6 +196,325 @@
};
};
+/*
+ * Legend: proper name = the GPIO line is used as GPIO
+ * NC = not connected (pin out but not routed from the chip to
+ * anything the board)
+ * "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ * "" = no idea, schematic doesn't say, could be
+ * unrouted (not connected to any external pin)
+ * LSEC = Low Speed External Connector
+ * HSEC = High Speed External Connector
+ *
+ * Line names are taken from "HiKey 960 Board ver A" schematics
+ * from Huawei. The 40 pin low speed expansion connector is named
+ * J2002 63453-140LF.
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART3. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
+&gpio0 {
+ /* GPIO_000-GPIO_007 */
+ gpio-line-names =
+ "",
+ "TP901", /* TEST_MODE connected to TP901 */
+ "[PMU0_SSI]",
+ "[PMU1_SSI]",
+ "[PMU2_SSI]",
+ "[PMU0_CLKOUT]",
+ "[JTAG_TCK]",
+ "[JTAG_TMS]";
+};
+
+&gpio1 {
+ /* GPIO_008-GPIO_015 */
+ gpio-line-names =
+ "[JTAG_TRST_N]",
+ "[JTAG_TDI]",
+ "[JTAG_TDO]",
+ "NC", "NC",
+ "[I2C3_SCL]",
+ "[I2C3_SDA]",
+ "NC";
+};
+
+&gpio2 {
+ /* GPIO_016-GPIO_023 */
+ gpio-line-names =
+ "NC", "NC", "NC",
+ "GPIO-J", /* LSEC pin 32: GPIO_019 */
+ "GPIO_020_HDMI_SEL",
+ "GPIO-L", /* LSEC pin 34: GPIO_021 */
+ "GPIO_022_UFSBUCK_INT_N",
+ "GPIO-G"; /* LSEC pin 29: LCD_TE0 */
+};
+
+&gpio3 {
+ /* GPIO_024-GPIO_031 */
+ /* The rail from pin BK36 is named LCD_TE0, we assume to be muxed as GPIO for GPIO-G */
+ gpio-line-names =
+ "[CSI0_MCLK]", /* HSEC pin 15: ISP_CCLK0_MCAM */
+ "[CSI1_MCLK]", /* HSEC pin 17: ISP_CCLK1_SCAM */
+ "NC",
+ "[I2C2_SCL]", /* HSEC pin 32: ISP_SCL0 */
+ "[I2C2_SDA]", /* HSEC pin 34: ISP_SDA0 */
+ "[I2C3_SCL]", /* HSEC pin 36: ISP_SCL1 */
+ "[I2C3_SDA]", /* HSEC pin 38: ISP_SDA1 */
+ "NC";
+};
+
+&gpio4 {
+ /* GPIO_032-GPIO_039 */
+ gpio-line-names =
+ "NC", "NC",
+ "PWR_BTN_N", /* LSEC pin 4: GPIO_034_PWRON_DET */
+ "GPIO_035_PMU2_EN",
+ "GPIO_036_USB_HUB_RESET",
+ "NC", "NC", "NC";
+};
+
+&gpio5 {
+ /* GPIO_040-GPIO_047 */
+ gpio-line-names =
+ "GPIO-H", /* LSEC pin 30: GPIO_040_LCD_RST_N */
+ "GPIO_041_HDMI_PD",
+ "TP904", /* Test point */
+ "TP905", /* Test point */
+ "NC", "NC",
+ "GPIO_046_HUB_VDD33_EN",
+ "GPIO_047_PMU1_EN";
+};
+
+&gpio6 {
+ /* GPIO_048-GPIO_055 */
+ gpio-line-names =
+ "NC", "NC", "NC",
+ "GPIO_051_WIFI_EN",
+ "GPIO-I", /* LSEC pin 31: GPIO_052_CAM0_RST_N */
+ /*
+ * These two pins should be used for SD(IO) data according to the
+ * 96boards specification but seems to be repurposed for a IRDA UART.
+ * They are however named according to the spec.
+ */
+ "[SD_DAT1]", /* HSEC pin 3: UART0_IRDA_RXD */
+ "[SD_DAT2]", /* HSEC pin 5: UART0_IRDA_TXD */
+ "[UART1_RXD]"; /* LSEC pin 13: DEBUG_UART6_RXD */
+};
+
+&gpio7 {
+ /* GPIO_056-GPIO_063 */
+ gpio-line-names =
+ "[UART1_TXD]", /* LSEC pin 11: DEBUG_UART6_TXD */
+ "[UART0_CTS]", /* LSEC pin 3: UART3_CTS_N */
+ "[UART0_RTS]", /* LSEC pin 9: UART3_RTS_N */
+ "[UART0_RXD]", /* LSEC pin 7: UART3_RXD */
+ "[UART0_TXD]", /* LSEC pin 5: UART3_TXD */
+ "[SOC_BT_UART4_CTS_N]",
+ "[SOC_BT_UART4_RTS_N]",
+ "[SOC_BT_UART4_RXD]";
+};
+
+&gpio8 {
+ /* GPIO_064-GPIO_071 */
+ gpio-line-names =
+ "[SOC_BT_UART4_TXD]",
+ "NC",
+ "[PMU_HKADC_SSI]",
+ "NC",
+ "GPIO_068_SEL",
+ "NC", "NC", "NC";
+
+};
+
+&gpio9 {
+ /* GPIO_072-GPIO_079 */
+ gpio-line-names =
+ "NC", "NC", "NC",
+ "GPIO-K", /* LSEC pin 33: GPIO_075_CAM1_RST_N */
+ "NC", "NC", "NC", "NC";
+};
+
+&gpio10 {
+ /* GPIO_080-GPIO_087 */
+ gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
+};
+
+&gpio11 {
+ /* GPIO_088-GPIO_095 */
+ gpio-line-names =
+ "NC",
+ "[PCIE_PERST_N]",
+ "NC", "NC", "NC", "NC", "NC", "NC";
+};
+
+&gpio12 {
+ /* GPIO_096-GPIO_103 */
+ gpio-line-names = "NC", "NC", "NC", "", "", "", "", "NC";
+};
+
+&gpio13 {
+ /* GPIO_104-GPIO_111 */
+ gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
+};
+
+&gpio14 {
+ /* GPIO_112-GPIO_119 */
+ gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
+};
+
+&gpio15 {
+ /* GPIO_120-GPIO_127 */
+ gpio-line-names =
+ "NC", "NC", "NC", "NC", "NC", "NC",
+ "GPIO_126_BT_EN",
+ "TP902"; /* GPIO_127_JTAG_SEL0 */
+};
+
+&gpio16 {
+ /* GPIO_128-GPIO_135 */
+ gpio-line-names = "", "", "", "", "", "", "", "";
+};
+
+&gpio17 {
+ /* GPIO_136-GPIO_143 */
+ gpio-line-names = "", "", "", "", "", "", "", "";
+};
+
+&gpio18 {
+ /* GPIO_144-GPIO_151 */
+ gpio-line-names =
+ "[UFS_REF_CLK]",
+ "[UFS_RST_N]",
+ "[SPI1_SCLK]", /* HSEC pin 9: GPIO_146_SPI3_CLK */
+ "[SPI1_DIN]", /* HSEC pin 11: GPIO_147_SPI3_DI */
+ "[SPI1_DOUT]", /* HSEC pin 1: GPIO_148_SPI3_DO */
+ "[SPI1_CS]", /* HSEC pin 7: GPIO_149_SPI3_CS0_N */
+ "GPIO_150_USER_LED1",
+ "GPIO_151_USER_LED2";
+};
+
+&gpio19 {
+ /* GPIO_152-GPIO_159 */
+ gpio-line-names = "NC", "NC", "NC", "NC", "", "", "", "";
+};
+
+&gpio20 {
+ /* GPIO_160-GPIO_167 */
+ gpio-line-names =
+ "[SD_CLK]",
+ "[SD_CMD]",
+ "[SD_DATA0]",
+ "[SD_DATA1]",
+ "[SD_DATA2]",
+ "[SD_DATA3]",
+ "", "";
+};
+
+&gpio21 {
+ /* GPIO_168-GPIO_175 */
+ gpio-line-names =
+ "[WL_SDIO_CLK]",
+ "[WL_SDIO_CMD]",
+ "[WL_SDIO_DATA0]",
+ "[WL_SDIO_DATA1]",
+ "[WL_SDIO_DATA2]",
+ "[WL_SDIO_DATA3]",
+ "", "";
+};
+
+&gpio22 {
+ /* GPIO_176-GPIO_183 */
+ gpio-line-names =
+ "[GPIO_176_PMU_PWR_HOLD]",
+ "NA",
+ "[SYSCLK_EN]",
+ "GPIO_179_WL_WAKEUP_AP",
+ "GPIO_180_HDMI_INT",
+ "NA",
+ "GPIO-F", /* LSEC pin 28: LCD_BL_PWM */
+ "[I2C0_SCL]"; /* LSEC pin 15 */
+};
+
+&gpio23 {
+ /* GPIO_184-GPIO_191 */
+ gpio-line-names =
+ "[I2C0_SDA]", /* LSEC pin 17 */
+ "[I2C1_SCL]", /* Actual SoC I2C1 */
+ "[I2C1_SDA]", /* Actual SoC I2C1 */
+ "[I2C1_SCL]", /* LSEC pin 19: I2C7_SCL */
+ "[I2C1_SDA]", /* LSEC pin 21: I2C7_SDA */
+ "GPIO_189_USER_LED3",
+ "GPIO_190_USER_LED4",
+ "",
+};
+
+&gpio24 {
+ /* GPIO_192-GPIO_199 */
+ gpio-line-names =
+ "[PCM_DI]", /* LSEC pin 22: GPIO_192_I2S0_DI */
+ "[PCM_DO]", /* LSEC pin 20: GPIO_193_I2S0_DO */
+ "[PCM_CLK]", /* LSEC pin 18: GPIO_194_I2S0_XCLK */
+ "[PCM_FS]", /* LSEC pin 16: GPIO_195_I2S0_XFS */
+ "[GPIO_196_I2S2_DI]",
+ "[GPIO_197_I2S2_DO]",
+ "[GPIO_198_I2S2_XCLK]",
+ "[GPIO_199_I2S2_XFS]";
+};
+
+&gpio25 {
+ /* GPIO_200-GPIO_207 */
+ gpio-line-names =
+ "NC",
+ "NC",
+ "GPIO_202_VBUS_TYPEC",
+ "GPIO_203_SD_DET",
+ "GPIO_204_PMU12_IRQ_N",
+ "GPIO_205_WIFI_ACTIVE",
+ "GPIO_206_USBSW_SEL",
+ "GPIO_207_BT_ACTIVE";
+};
+
+&gpio26 {
+ /* GPIO_208-GPIO_215 */
+ gpio-line-names =
+ "GPIO-A", /* LSEC pin 23: GPIO_208 */
+ "GPIO-B", /* LSEC pin 24: GPIO_209 */
+ "GPIO-C", /* LSEC pin 25: GPIO_210 */
+ "GPIO-D", /* LSEC pin 26: GPIO_211 */
+ "GPIO-E", /* LSEC pin 27: GPIO_212 */
+ "[PCIE_CLKREQ_N]",
+ "[PCIE_WAKE_N]",
+ "[SPI0_CLK]"; /* LSEC pin 8: SPI2_CLK */
+};
+
+&gpio27 {
+ /* GPIO_216-GPIO_223 */
+ gpio-line-names =
+ "[SPI0_DIN]", /* LSEC pin 10: SPI2_DI */
+ "[SPI0_DOUT]", /* LSEC pin 14: SPI2_DO */
+ "[SPI0_CS]", /* LSEC pin 12: SPI2_CS0_N */
+ "GPIO_219_CC_INT",
+ "NC",
+ "NC",
+ "[PMU_INT]",
+ "";
+};
+
+&gpio28 {
+ /* GPIO_224-GPIO_231 */
+ gpio-line-names =
+ "", "", "", "", "", "", "", "";
+};
+
&i2c0 {
/* On Low speed expansion */
label = "LS-I2C0";
This adds line names for all the GPIOs I could identify on the HiKey960 schematic. "GPIO-A" through "GPIO-L" are the most important since they give users a handle to look up the standard 96boards GPIOs from the GPIO character device. The rest of the names are more informational, nice debug information for "lsgpio" so you can see that the right line is taken for the right function in the kernel for example. Cc: Wei Xu <xuwei5@hisilicon.com> Cc: Zhangfei Gao <zhangfei.gao@hisilicon.com> Cc: Guodong Xu <guodong.xu@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- Wei: can you test this please? I'm not sure it even compiles but I think it should look like this with maybe minor tweaks, if you know some of the undefined lines or see some errors feel free to fix it up. --- arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 319 ++++++++++++++++++++++ 1 file changed, 319 insertions(+)