new file mode 100644
@@ -0,0 +1,60 @@
+Freescale i.MX audio complex with ES8328 codec
+
+Required properties:
+- compatible : "fsl,imx-audio-es8328"
+- model : The user-visible name of this sound complex
+- clocks : A list of clocks required to run the codec at 22.5792 MHz
+- ssi-controller : The phandle of the i.MX SSI controller
+- jack-gpio : Optional GPIO for headphone jack
+- codec-supply : Power regulator for audio codec chip
+- audio-amp-supply : Power regulator for speaker amps
+- audio-codec : The phandle of the ES8328 audio codec
+- audio-routing : A list of the connections between audio components.
+ Each entry is a pair of strings, the first being the connection's sink,
+ the second being the connection's source. Valid names could be power
+ supplies, ES8328 pins, and the jacks on the board:
+
+ Power supplies:
+ * audio-amp
+ * codec
+
+ ES8328 pins:
+ * LOUT1
+ * LOUT2
+ * ROUT1
+ * ROUT2
+
+ Board connectors:
+ * Headphone
+ * Speaker
+
+- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX)
+- mux-ext-port : The external port of the i.MX audio muxer
+
+Note: The AUDMUX port numbering should start at 1, which is consistent with
+hardware manual.
+
+Example:
+
+sound {
+ compatible = "fsl,imx-audio-es8328";
+ model = "imx-audio-es8328";
+ clocks = <&clks 169>, <&clks 57>, <&clks 173>,
+ <&clks 203>, <&clks 201>;
+ clock-names = "cko1", "cko1_sel", "pll4_audio",
+ "pll4_post_div", "cko_sel";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&codec>;
+ jack-gpio = <&gpio5 15 0>;
+ codec-supply = <®_audio_codec>;
+ audio-amp-supply = <®_audio_amp>;
+ audio-routing =
+ "Speaker", "LOUT2",
+ "Speaker", "ROUT2",
+ "Speaker", "audio-amp",
+ "Headphone", "ROUT1",
+ "Headphone", "LOUT1";
+ mux-int-port = <1>;
+ mux-ext-port = <3>;
+};
+
@@ -229,6 +229,19 @@ config SND_SOC_IMX_WM8962
Say Y if you want to add support for SoC audio on an i.MX board with
a wm8962 codec.
+config SND_SOC_IMX_ES8328
+ tristate "SoC Audio support for i.MX boards with the ES8328 codec"
+ depends on OF && (I2C || SPI)
+ select SND_SOC_ES8328
+ select SND_SOC_IMX_PCM_DMA
+ select SND_SOC_IMX_AUDMUX
+ select SND_SOC_FSL_SSI
+ select SND_SOC_FSL_UTILS
+ select SND_SOC_IMX_PCM_FIQ
+ help
+ Say Y if you want to add support for the ES8328 audio codec connected
+ via SSI/I2S over either SPI or I2C.
+
config SND_SOC_IMX_SGTL5000
tristate "SoC Audio support for i.MX boards with sgtl5000"
depends on OF && I2C
@@ -48,6 +48,7 @@ snd-soc-eukrea-tlv320-objs := eukrea-tlv320.o
snd-soc-phycore-ac97-objs := phycore-ac97.o
snd-soc-mx27vis-aic32x4-objs := mx27vis-aic32x4.o
snd-soc-wm1133-ev1-objs := wm1133-ev1.o
+snd-soc-imx-es8328-objs := imx-es8328.o
snd-soc-imx-sgtl5000-objs := imx-sgtl5000.o
snd-soc-imx-wm8962-objs := imx-wm8962.o
snd-soc-imx-spdif-objs := imx-spdif.o
@@ -57,6 +58,7 @@ obj-$(CONFIG_SND_SOC_EUKREA_TLV320) += snd-soc-eukrea-tlv320.o
obj-$(CONFIG_SND_SOC_PHYCORE_AC97) += snd-soc-phycore-ac97.o
obj-$(CONFIG_SND_SOC_MX27VIS_AIC32X4) += snd-soc-mx27vis-aic32x4.o
obj-$(CONFIG_SND_MXC_SOC_WM1133_EV1) += snd-soc-wm1133-ev1.o
+obj-$(CONFIG_SND_SOC_IMX_ES8328) += snd-soc-imx-es8328.o
obj-$(CONFIG_SND_SOC_IMX_SGTL5000) += snd-soc-imx-sgtl5000.o
obj-$(CONFIG_SND_SOC_IMX_WM8962) += snd-soc-imx-wm8962.o
obj-$(CONFIG_SND_SOC_IMX_SPDIF) += snd-soc-imx-spdif.o
new file mode 100644
@@ -0,0 +1,359 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2012 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/i2c.h>
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
+#include <linux/regulator/consumer.h>
+#include <linux/clk-provider.h>
+#include <sound/soc.h>
+#include <sound/jack.h>
+
+#include "imx-audmux.h"
+
+#define DAI_NAME_SIZE 32
+#define IMX6Q_SYSCLK 0x00
+
+struct imx_es8328_data {
+ struct device *dev;
+ struct snd_soc_dai_link dai;
+ struct snd_soc_card card;
+ struct regulator *codec_regulator;
+ char codec_dai_name[DAI_NAME_SIZE];
+ char platform_name[DAI_NAME_SIZE];
+ struct clk *codec_clk;
+ struct clk *codec_clk_src;
+ struct clk *codec_clk_sel;
+ struct clk *codec_clk_post_div;
+ struct clk *system_cko;
+ unsigned int clk_freq_src;
+ unsigned int clk_frequency;
+ int power_gpio;
+ int jack_gpio;
+};
+
+static struct snd_soc_jack_gpio headset_jack_gpios[] = {
+ {
+ .gpio = -1,
+ .name = "headset-gpio",
+ .report = SND_JACK_HEADSET,
+ .invert = 0,
+ .debounce_time = 200,
+ },
+};
+
+static struct snd_soc_jack headset_jack;
+
+static int imx_es8328_dai_init(struct snd_soc_pcm_runtime *rtd)
+{
+ struct imx_es8328_data *data = container_of(rtd->card,
+ struct imx_es8328_data, card);
+ struct device *dev = rtd->card->dev;
+ int ret;
+
+ ret = snd_soc_dai_set_sysclk(rtd->codec_dai, IMX6Q_SYSCLK,
+ data->clk_frequency, SND_SOC_CLOCK_IN);
+ if (ret) {
+ dev_err(dev, "could not set codec driver clock params to %d\n",
+ data->clk_frequency);
+ return ret;
+ }
+
+ /* Headphone jack detection */
+ if (gpio_is_valid(data->jack_gpio)) {
+ ret = snd_soc_jack_new(rtd->codec, "Headphone",
+ SND_JACK_HEADPHONE | SND_JACK_BTN_0,
+ &headset_jack);
+ if (ret)
+ return ret;
+
+ headset_jack_gpios[0].gpio = data->jack_gpio;
+ ret = snd_soc_jack_add_gpios(&headset_jack,
+ ARRAY_SIZE(headset_jack_gpios),
+ headset_jack_gpios);
+ }
+
+ return ret;
+}
+
+static const struct snd_soc_dapm_widget imx_es8328_dapm_widgets[] = {
+ SND_SOC_DAPM_MIC("Mic Jack", NULL),
+ SND_SOC_DAPM_HP("Headphone", NULL),
+ SND_SOC_DAPM_SPK("Speaker", NULL),
+ SND_SOC_DAPM_REGULATOR_SUPPLY("audio-amp", 1, 0),
+};
+
+static int imx_set_frequency(struct imx_es8328_data *data, int freq)
+{
+ int ret;
+
+ ret = clk_set_parent(data->system_cko, data->codec_clk);
+ if (ret) {
+ dev_err(data->dev, "unable to set clk output");
+ return ret;
+ }
+
+ ret = clk_set_parent(data->codec_clk_sel, data->codec_clk_post_div);
+ if (ret) {
+ dev_err(data->dev, "unable to set clk parent");
+ return ret;
+ }
+
+ data->clk_freq_src = clk_round_rate(data->codec_clk_src, freq * 32);
+ data->clk_frequency = clk_round_rate(data->codec_clk, freq);
+ dev_dbg(data->dev, "clock source frequency: %d\n", data->clk_freq_src);
+ dev_dbg(data->dev, "clock frequency: %d\n", data->clk_frequency);
+
+ ret = clk_set_rate(data->codec_clk_src, data->clk_freq_src);
+ if (ret) {
+ dev_err(data->dev, "unable to set source clock rate\n");
+ return ret;
+ }
+
+ ret = clk_set_rate(data->codec_clk, data->clk_frequency);
+ if (ret) {
+ dev_err(data->dev, "unable to set codec clock rate\n");
+ return ret;
+ }
+
+ ret = clk_prepare_enable(data->codec_clk);
+ if (ret) {
+ dev_err(data->dev, "unable to prepare codec clk\n");
+ return ret;
+ }
+
+ ret = clk_prepare_enable(data->codec_clk_src);
+ if (ret) {
+ dev_err(data->dev, "unable to prepare codec clk source\n");
+ return ret;
+ }
+ return ret;
+}
+
+static int imx_es8328_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *ssi_np, *codec_np;
+ struct platform_device *ssi_pdev;
+ struct imx_es8328_data *data;
+ int int_port, ext_port;
+ int ret;
+ struct device *dev = &pdev->dev;
+
+ ret = of_property_read_u32(np, "mux-int-port", &int_port);
+ if (ret) {
+ dev_err(&pdev->dev, "mux-int-port missing or invalid\n");
+ return ret;
+ }
+ ret = of_property_read_u32(np, "mux-ext-port", &ext_port);
+ if (ret) {
+ dev_err(&pdev->dev, "mux-ext-port missing or invalid\n");
+ return ret;
+ }
+
+ /*
+ * The port numbering in the hardware manual starts at 1, while
+ * the audmux API expects it starts at 0.
+ */
+ int_port--;
+ ext_port--;
+ ret = imx_audmux_v2_configure_port(int_port,
+ IMX_AUDMUX_V2_PTCR_SYN |
+ IMX_AUDMUX_V2_PTCR_TFSEL(ext_port) |
+ IMX_AUDMUX_V2_PTCR_TCSEL(ext_port) |
+ IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR,
+ IMX_AUDMUX_V2_PDCR_RXDSEL(ext_port));
+ if (ret) {
+ dev_err(&pdev->dev, "audmux internal port setup failed\n");
+ return ret;
+ }
+ ret = imx_audmux_v2_configure_port(ext_port,
+ IMX_AUDMUX_V2_PTCR_SYN,
+ IMX_AUDMUX_V2_PDCR_RXDSEL(int_port));
+ if (ret) {
+ dev_err(&pdev->dev, "audmux external port setup failed\n");
+ return ret;
+ }
+
+ ssi_np = of_parse_phandle(pdev->dev.of_node, "ssi-controller", 0);
+ codec_np = of_parse_phandle(pdev->dev.of_node, "audio-codec", 0);
+ if (!ssi_np || !codec_np) {
+ dev_err(&pdev->dev, "phandle missing or invalid\n");
+ ret = -EINVAL;
+ goto fail;
+ }
+
+ ssi_pdev = of_find_device_by_node(ssi_np);
+ if (!ssi_pdev) {
+ dev_err(&pdev->dev, "failed to find SSI platform device\n");
+ ret = -EINVAL;
+ goto fail;
+ }
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data) {
+ ret = -ENOMEM;
+ goto fail;
+ }
+
+ data->dev = dev;
+
+ data->jack_gpio = of_get_named_gpio(pdev->dev.of_node,
+ "jack-gpio", 0);
+
+ data->power_gpio = of_get_named_gpio(pdev->dev.of_node,
+ "power-gpio", 0);
+ if (gpio_is_valid(data->power_gpio))
+ devm_gpio_request_one(&pdev->dev, data->power_gpio,
+ GPIOF_OUT_INIT_HIGH,
+ "audio codec power switch");
+
+ /* Setup clocks */
+ data->codec_clk = devm_clk_get(dev, "cko1");
+ if (IS_ERR(data->codec_clk)) {
+ dev_err(dev,
+ "codec clock missing or invalid\n");
+ goto fail;
+ }
+
+ data->codec_clk_sel = devm_clk_get(dev, "cko1_sel");
+ if (IS_ERR(data->codec_clk_sel)) {
+ dev_err(dev,
+ "codec clock select missing or invalid\n");
+ goto fail;
+ }
+
+ data->codec_clk_src = devm_clk_get(dev, "pll4_audio");
+ if (IS_ERR(data->codec_clk_src)) {
+ dev_err(dev,
+ "codec clock source missing or invalid\n");
+ goto fail;
+ }
+
+ data->codec_clk_post_div = devm_clk_get(dev, "pll4_post_div");
+ if (IS_ERR(data->codec_clk_post_div)) {
+ dev_err(dev,
+ "codec clock post-div missing or invalid\n");
+ goto fail;
+ }
+
+ data->system_cko = devm_clk_get(dev, "cko_sel");
+ if (IS_ERR(data->system_cko)) {
+ dev_err(dev,
+ "system clock missing or invalid\n");
+ goto fail;
+ }
+
+ ret = imx_set_frequency(data, 22579200);
+ if (ret)
+ goto fail;
+
+ data->codec_regulator = devm_regulator_get(dev, "codec");
+ if (IS_ERR(data->codec_regulator)) {
+ dev_err(dev, "No codec regulator\n");
+ data->codec_regulator = NULL;
+ } else {
+ ret = regulator_enable(data->codec_regulator);
+ if (ret)
+ dev_err(dev,
+ "Unable to enable codec regulator: %d\n", ret);
+ }
+
+ data->dai.name = "hifi";
+ data->dai.stream_name = "hifi";
+ data->dai.codec_dai_name = "es8328-hifi-analog";
+ data->dai.codec_of_node = codec_np;
+ data->dai.cpu_of_node = ssi_np;
+ data->dai.platform_of_node = ssi_np;
+ data->dai.init = &imx_es8328_dai_init;
+ data->dai.dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
+ SND_SOC_DAIFMT_CBM_CFM;
+
+ data->card.dev = &pdev->dev;
+ data->card.dapm_widgets = imx_es8328_dapm_widgets;
+ data->card.num_dapm_widgets = ARRAY_SIZE(imx_es8328_dapm_widgets);
+ ret = snd_soc_of_parse_card_name(&data->card, "model");
+ if (ret)
+ goto fail;
+ ret = snd_soc_of_parse_audio_routing(&data->card, "audio-routing");
+ if (ret)
+ goto fail;
+ data->card.num_links = 1;
+ data->card.owner = THIS_MODULE;
+ data->card.dai_link = &data->dai;
+
+ ret = snd_soc_register_card(&data->card);
+ if (ret)
+ goto fail;
+
+ platform_set_drvdata(pdev, data);
+fail:
+ if (ssi_np)
+ of_node_put(ssi_np);
+ if (codec_np)
+ of_node_put(codec_np);
+
+ return ret;
+}
+
+static int imx_es8328_remove(struct platform_device *pdev)
+{
+ struct imx_es8328_data *data = platform_get_drvdata(pdev);
+
+ snd_soc_jack_free_gpios(&headset_jack, ARRAY_SIZE(headset_jack_gpios),
+ headset_jack_gpios);
+ if (data->codec_regulator) {
+ int ret;
+
+ ret = regulator_disable(data->codec_regulator);
+ if (ret)
+ dev_err(&pdev->dev,
+ "Unable to disable codec regulator: %d\n", ret);
+ }
+
+ if (data->codec_clk)
+ clk_disable_unprepare(data->codec_clk);
+
+ if (data->codec_clk_src)
+ clk_disable_unprepare(data->codec_clk_src);
+
+ snd_soc_unregister_card(&data->card);
+
+ return 0;
+}
+
+static const struct of_device_id imx_es8328_dt_ids[] = {
+ { .compatible = "fsl,imx-audio-es8328", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx_es8328_dt_ids);
+
+static struct platform_driver imx_es8328_driver = {
+ .driver = {
+ .name = "imx-es8328",
+ .owner = THIS_MODULE,
+ .of_match_table = imx_es8328_dt_ids,
+ },
+ .probe = imx_es8328_probe,
+ .remove = imx_es8328_remove,
+};
+module_platform_driver(imx_es8328_driver);
+
+MODULE_AUTHOR("Sean Cross <xobs@kosagi.com>");
+MODULE_DESCRIPTION("Kosagi i.MX6 ES8328 ASoC machine driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:imx-audio-es8328");
This adds an initial machine driver for the ES8328 audio codec. The driver supports headphones, an audio regulator for both the codec itself and a speaker amp, and supports reparenting and adjusting clocks to supply the audio codec with the unusual frequency it requires. Signed-off-by: Sean Cross <xobs@kosagi.com> --- .../devicetree/bindings/sound/imx-audio-es8328.txt | 60 ++++ sound/soc/fsl/Kconfig | 13 + sound/soc/fsl/Makefile | 2 + sound/soc/fsl/imx-es8328.c | 359 +++++++++++++++++++++ 4 files changed, 434 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/imx-audio-es8328.txt create mode 100644 sound/soc/fsl/imx-es8328.c