| Message ID | 1594184896-10629-9-git-send-email-rohitkr@codeaurora.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | ASoC: qcom: Add support for SC7180 lpass variant | expand |
On Wed, Jul 08, 2020 at 10:38:16AM +0530, Rohit kumar wrote: > From: Ajit Pandey <ajitp@codeaurora.org> > > Update lpass-cpu binding with yaml formats. > > Signed-off-by: Ajit Pandey <ajitp@codeaurora.org> > Signed-off-by: Rohit kumar <rohitkr@codeaurora.org> > --- > .../devicetree/bindings/sound/qcom,lpass-cpu.txt | 80 ----------- > .../devicetree/bindings/sound/qcom,lpass-cpu.yaml | 154 +++++++++++++++++++++ > 2 files changed, 154 insertions(+), 80 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt > create mode 100644 Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml > > diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt > deleted file mode 100644 > index 04e34cc..00000000 > --- a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt > +++ /dev/null > @@ -1,80 +0,0 @@ > -* Qualcomm Technologies LPASS CPU DAI > - > -This node models the Qualcomm Technologies Low-Power Audio SubSystem (LPASS). > - > -Required properties: > - > -- compatible : "qcom,lpass-cpu" or "qcom,apq8016-lpass-cpu" or > - "qcom,lpass-cpu-sc7180" > -- clocks : Must contain an entry for each entry in clock-names. > -- clock-names : A list which must include the following entries: > - * "ahbix-clk" > - * "mi2s-osr-clk" > - * "mi2s-bit-clk" > - : required clocks for "qcom,lpass-cpu-apq8016" > - * "ahbix-clk" > - * "mi2s-bit-clk0" > - * "mi2s-bit-clk1" > - * "mi2s-bit-clk2" > - * "mi2s-bit-clk3" > - * "pcnoc-mport-clk" > - * "pcnoc-sway-clk" > - > -- interrupts : Must contain an entry for each entry in > - interrupt-names. > -- interrupt-names : A list which must include the following entries: > - * "lpass-irq-lpaif" > -- pinctrl-N : One property must exist for each entry in > - pinctrl-names. See ../pinctrl/pinctrl-bindings.txt > - for details of the property values. > -- pinctrl-names : Must contain a "default" entry. > -- reg : Must contain an address for each entry in reg-names. > -- reg-names : A list which must include the following entries: > - * "lpass-lpaif" > -- #address-cells : Must be 1 > -- #size-cells : Must be 0 > - > - > - > -Optional properties: > - > -- qcom,adsp : Phandle for the audio DSP node > - > -By default, the driver uses up to 4 MI2S SD lines, for a total of 8 channels. > -The SD lines to use can be configured by adding subnodes for each of the DAIs. > - > -Required properties for each DAI (represented by a subnode): > -- reg : Must be one of the DAI IDs > - (usually part of dt-bindings header) > -- qcom,playback-sd-lines: List of serial data lines to use for playback > - Each SD line should be represented by a number from 0-3. > -- qcom,capture-sd-lines : List of serial data lines to use for capture > - Each SD line should be represented by a number from 0-3. > - > -Note that adding a subnode changes the default to "no lines configured", > -so both playback and capture lines should be configured when a subnode is added. > - > -Example: > - > -lpass@28100000 { > - compatible = "qcom,lpass-cpu"; > - clocks = <&lcc AHBIX_CLK>, <&lcc MI2S_OSR_CLK>, <&lcc MI2S_BIT_CLK>; > - clock-names = "ahbix-clk", "mi2s-osr-clk", "mi2s-bit-clk"; > - interrupts = <0 85 1>; > - interrupt-names = "lpass-irq-lpaif"; > - pinctrl-names = "default", "idle"; > - pinctrl-0 = <&mi2s_default>; > - pinctrl-1 = <&mi2s_idle>; > - reg = <0x28100000 0x10000>; > - reg-names = "lpass-lpaif"; > - qcom,adsp = <&adsp>; > - > - #address-cells = <1>; > - #size-cells = <0>; > - > - /* Optional to set different MI2S SD lines */ > - dai@3 { > - reg = <MI2S_QUATERNARY>; > - qcom,playback-sd-lines = <0 1>; > - }; > -}; > diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml > new file mode 100644 > index 00000000..9c350bc > --- /dev/null > +++ b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml > @@ -0,0 +1,154 @@ > +# SPDX-License-Identifier: GPL-2.0-only > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/sound/qcom,lpass-cpu.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm LPASS CPU dai driver bindings > + > +maintainers: > + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > + - Rohit kumar <rohitkr@codeaurora.org> > + > +description: > + Qualcomm SOC Low-Power Audio SubSystem (LPASS) that consist of MI2S interface > + for audio data transfer on external codecs. LPASS cpu driver is a module to > + configure Low-Power Audio Interface(LPAIF) core registers across different > + IP versions. > + > +properties: > + compatible: > + enum: > + - qcom,lpass-cpu > + - qcom,apq8016-lpass-cpu > + - qcom,lpass-cpu-sc7180 > + > + reg: > + items: > + - description: LPAIF core registers Just: 'maxItems: 1' for a single entry. > + > + reg-names: > + items: > + - const: lpass-lpaif Not all that useful with only 1. > + > + clocks: > + items: > + - description: AHBIX core clock > + - description: oscillator clock for MI2S external interfaces > + - description: Bit clock for single MI2S dai > + - description: Bit clock for MI2S_PRIMARY dai interface > + - description: Bit clock for MI2S_SECONDARY dai interface > + - description: Bit clock for MI2S_TERTIARY dai interface > + - description: Bit clock for MI2S_QUATERNARY dai interface > + - description: NOC MPORT clock of LPASS core > + - description: NOC SWAY clock of LPASS core > + > + clock-names: > + items: > + - const: ahbix-clk > + - const: mi2s-osr-clk > + - const: mi2s-bit-clk > + - const: mi2s-bit-clk0 > + - const: mi2s-bit-clk1 > + - const: mi2s-bit-clk2 > + - const: mi2s-bit-clk3 > + - const: pcnoc-mport-clk > + - const: pcnoc-sway-clk > + > + interrupts: > + items: > + - description: LPAIF DMA buffer interrupt maxItems: 1 > + > + interrupt-names: > + items: > + - const: lpass-irq-lpaif > + > + qcom,adsp: > + maxItems: 1 > + description: Phandle for the audio DSP node Needs a type $ref. And if just a phandle, 'maxItems: 1' is not appropriate. > + > + iommus: > + maxItems: 1 > + description: Phandle to apps_smmu node with sid mask > + > + power-domains: > + maxItems: 1 > + description: Phandle for power domain node Drop. That's every 'power-domains' property. > + > + '#sound-dai-cells': > + const: 1 > + > + child-node: I'm sure I said this on some review recently, but you are defining a child node named 'child-node'. You need this under patternProperties with the actual child node name. > + description: Required properties for each DAI > + type: object > + properties: > + reg: > + description: Must be one of the DAI ID > + (Usually part of dtbindings header) Ideally, you'd define the range of values here. > + qcom,playback-sd-lines: > + description: List of serial data lines to use for playback > + Each SD line should be represented by a number from 0-3. Needs a type $ref and 0-3 should be expressed as a schema. 'make dt_binding_check' should complain about this. You did run that, right? > + qcom,capture-sd-lines : > + description: List of serial data lines to use for capture > + Each SD line should be represented by a number from 0-3. ditto > + required: > + -reg space ^ > + # Note that adding a subnode changes the default to "no lines configured", > + # so both playback and capture lines should be configured when a subnode > + # is added. > + > + > +required: > + - compatible > + - reg > + - reg-names > + - clocks > + - clock-names > + - interrupts > + - interrupt-names > + - sound-dai-cells Not a valid property. > + > +optional: > + - qcom,adsp > + > +if: > + properties: > + compatible: > + contains: > + const: qcom,lpass-cpu-sc7180 > + > +then: > + required: > + - iommus > + - power-domains > + > +examples: > + lpass@28100000 { This is not valid. 'examples' should be a list. > + compatible = "qcom,lpass-cpu"; > + clocks = <&lcc AHBIX_CLK>, > + <&lcc MI2S_OSR_CLK>, > + <&lcc MI2S_BIT_CLK>; The example will not build because the includes are missing. > + > + clock-names = "ahbix-clk", > + "mi2s-osr-clk", > + "mi2s-bit-clk"; > + > + interrupts = <0 85 1>; > + interrupt-names = "lpass-irq-lpaif"; > + > + iommus = <&apps_smmu 0x1020 0>; > + power-domains = <&lpass_hm LPASS_CORE_HM_GDSCR>; > + > + reg = <0x28100000 0x10000>; > + reg-names = "lpass-lpaif"; > + #sound-dai-cells = <1>; > + qcom,adsp = <&adsp>; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + /* Optional to set different MI2S SD lines */ > + mi2s-quaternary@3 { > + reg = <MI2S_QUATERNARY>; > + qcom,playback-sd-lines = <0 1>; > + }; > -- > Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc., > is a member of Code Aurora Forum, a Linux Foundation Collaborative Project. >
Thanks Rob for the review. Posted v4 with fixes. On 7/14/2020 4:23 AM, Rob Herring wrote: > On Wed, Jul 08, 2020 at 10:38:16AM +0530, Rohit kumar wrote: >> From: Ajit Pandey <ajitp@codeaurora.org> >> >> Update lpass-cpu binding with yaml formats. >> >> Signed-off-by: Ajit Pandey <ajitp@codeaurora.org> >> Signed-off-by: Rohit kumar <rohitkr@codeaurora.org> >> --- >> .../devicetree/bindings/sound/qcom,lpass-cpu.txt | 80 ----------- >> .../devicetree/bindings/sound/qcom,lpass-cpu.yaml | 154 +++++++++++++++++++++ >> 2 files changed, 154 insertions(+), 80 deletions(-) >> delete mode 100644 Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt >> create mode 100644 Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml >> >> diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt >> deleted file mode 100644 >> index 04e34cc..00000000 >> --- a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt >> +++ /dev/null >> @@ -1,80 +0,0 @@ >> -* Qualcomm Technologies LPASS CPU DAI >> - >> -This node models the Qualcomm Technologies Low-Power Audio SubSystem (LPASS). >> - >> -Required properties: >> - >> -- compatible : "qcom,lpass-cpu" or "qcom,apq8016-lpass-cpu" or >> - "qcom,lpass-cpu-sc7180" >> -- clocks : Must contain an entry for each entry in clock-names. >> -- clock-names : A list which must include the following entries: >> - * "ahbix-clk" >> - * "mi2s-osr-clk" >> - * "mi2s-bit-clk" >> - : required clocks for "qcom,lpass-cpu-apq8016" >> - * "ahbix-clk" >> - * "mi2s-bit-clk0" >> - * "mi2s-bit-clk1" >> - * "mi2s-bit-clk2" >> - * "mi2s-bit-clk3" >> - * "pcnoc-mport-clk" >> - * "pcnoc-sway-clk" >> - >> -- interrupts : Must contain an entry for each entry in >> - interrupt-names. >> -- interrupt-names : A list which must include the following entries: >> - * "lpass-irq-lpaif" >> -- pinctrl-N : One property must exist for each entry in >> - pinctrl-names. See ../pinctrl/pinctrl-bindings.txt >> - for details of the property values. >> -- pinctrl-names : Must contain a "default" entry. >> -- reg : Must contain an address for each entry in reg-names. >> -- reg-names : A list which must include the following entries: >> - * "lpass-lpaif" >> -- #address-cells : Must be 1 >> -- #size-cells : Must be 0 >> - >> - >> - >> -Optional properties: >> - >> -- qcom,adsp : Phandle for the audio DSP node >> - >> -By default, the driver uses up to 4 MI2S SD lines, for a total of 8 channels. >> -The SD lines to use can be configured by adding subnodes for each of the DAIs. >> - >> -Required properties for each DAI (represented by a subnode): >> -- reg : Must be one of the DAI IDs >> - (usually part of dt-bindings header) >> -- qcom,playback-sd-lines: List of serial data lines to use for playback >> - Each SD line should be represented by a number from 0-3. >> -- qcom,capture-sd-lines : List of serial data lines to use for capture >> - Each SD line should be represented by a number from 0-3. >> - >> -Note that adding a subnode changes the default to "no lines configured", >> -so both playback and capture lines should be configured when a subnode is added. >> - >> -Example: >> - >> -lpass@28100000 { >> - compatible = "qcom,lpass-cpu"; >> - clocks = <&lcc AHBIX_CLK>, <&lcc MI2S_OSR_CLK>, <&lcc MI2S_BIT_CLK>; >> - clock-names = "ahbix-clk", "mi2s-osr-clk", "mi2s-bit-clk"; >> - interrupts = <0 85 1>; >> - interrupt-names = "lpass-irq-lpaif"; >> - pinctrl-names = "default", "idle"; >> - pinctrl-0 = <&mi2s_default>; >> - pinctrl-1 = <&mi2s_idle>; >> - reg = <0x28100000 0x10000>; >> - reg-names = "lpass-lpaif"; >> - qcom,adsp = <&adsp>; >> - >> - #address-cells = <1>; >> - #size-cells = <0>; >> - >> - /* Optional to set different MI2S SD lines */ >> - dai@3 { >> - reg = <MI2S_QUATERNARY>; >> - qcom,playback-sd-lines = <0 1>; >> - }; >> -}; >> diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml >> new file mode 100644 >> index 00000000..9c350bc >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml >> @@ -0,0 +1,154 @@ >> +# SPDX-License-Identifier: GPL-2.0-only >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/sound/qcom,lpass-cpu.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Qualcomm LPASS CPU dai driver bindings >> + >> +maintainers: >> + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >> + - Rohit kumar <rohitkr@codeaurora.org> >> + >> +description: >> + Qualcomm SOC Low-Power Audio SubSystem (LPASS) that consist of MI2S interface >> + for audio data transfer on external codecs. LPASS cpu driver is a module to >> + configure Low-Power Audio Interface(LPAIF) core registers across different >> + IP versions. >> + >> +properties: >> + compatible: >> + enum: >> + - qcom,lpass-cpu >> + - qcom,apq8016-lpass-cpu >> + - qcom,lpass-cpu-sc7180 >> + >> + reg: >> + items: >> + - description: LPAIF core registers > Just: 'maxItems: 1' for a single entry. pl > >> + >> + reg-names: >> + items: >> + - const: lpass-lpaif > Not all that useful with only 1. ok .. Removed in v4. > >> + >> + clocks: >> + items: >> + - description: AHBIX core clock >> + - description: oscillator clock for MI2S external interfaces >> + - description: Bit clock for single MI2S dai >> + - description: Bit clock for MI2S_PRIMARY dai interface >> + - description: Bit clock for MI2S_SECONDARY dai interface >> + - description: Bit clock for MI2S_TERTIARY dai interface >> + - description: Bit clock for MI2S_QUATERNARY dai interface >> + - description: NOC MPORT clock of LPASS core >> + - description: NOC SWAY clock of LPASS core >> + >> + clock-names: >> + items: >> + - const: ahbix-clk >> + - const: mi2s-osr-clk >> + - const: mi2s-bit-clk >> + - const: mi2s-bit-clk0 >> + - const: mi2s-bit-clk1 >> + - const: mi2s-bit-clk2 >> + - const: mi2s-bit-clk3 >> + - const: pcnoc-mport-clk >> + - const: pcnoc-sway-clk >> + >> + interrupts: >> + items: >> + - description: LPAIF DMA buffer interrupt > maxItems: 1 ok > >> + >> + interrupt-names: >> + items: >> + - const: lpass-irq-lpaif >> + >> + qcom,adsp: >> + maxItems: 1 >> + description: Phandle for the audio DSP node > Needs a type $ref. And if just a phandle, 'maxItems: 1' is not > appropriate. > >> + >> + iommus: >> + maxItems: 1 >> + description: Phandle to apps_smmu node with sid mask >> + >> + power-domains: >> + maxItems: 1 >> + description: Phandle for power domain node > Drop. That's every 'power-domains' property. ok >> + >> + '#sound-dai-cells': >> + const: 1 >> + >> + child-node: > I'm sure I said this on some review recently, but you are defining a > child node named 'child-node'. You need this under patternProperties > with the actual child node name. Done in v4. > >> + description: Required properties for each DAI >> + type: object >> + properties: >> + reg: >> + description: Must be one of the DAI ID >> + (Usually part of dtbindings header) > Ideally, you'd define the range of values here. > >> + qcom,playback-sd-lines: >> + description: List of serial data lines to use for playback >> + Each SD line should be represented by a number from 0-3. > Needs a type $ref and 0-3 should be expressed as a schema. > > 'make dt_binding_check' should complain about this. You did run that, > right? Actually I reposted the Ajit's patch. Fixed all issues in v4. >> + qcom,capture-sd-lines : >> + description: List of serial data lines to use for capture >> + Each SD line should be represented by a number from 0-3. > ditto > >> + required: >> + -reg > space ^ > >> + # Note that adding a subnode changes the default to "no lines configured", >> + # so both playback and capture lines should be configured when a subnode >> + # is added. >> + >> + >> +required: >> + - compatible >> + - reg >> + - reg-names >> + - clocks >> + - clock-names >> + - interrupts >> + - interrupt-names >> + - sound-dai-cells > Not a valid property. > >> + >> +optional: >> + - qcom,adsp >> + >> +if: >> + properties: >> + compatible: >> + contains: >> + const: qcom,lpass-cpu-sc7180 >> + >> +then: >> + required: >> + - iommus >> + - power-domains >> + >> +examples: >> + lpass@28100000 { > This is not valid. 'examples' should be a list. > >> + compatible = "qcom,lpass-cpu"; >> + clocks = <&lcc AHBIX_CLK>, >> + <&lcc MI2S_OSR_CLK>, >> + <&lcc MI2S_BIT_CLK>; > The example will not build because the includes are missing. > >> + >> + clock-names = "ahbix-clk", >> + "mi2s-osr-clk", >> + "mi2s-bit-clk"; >> + >> + interrupts = <0 85 1>; >> + interrupt-names = "lpass-irq-lpaif"; >> + >> + iommus = <&apps_smmu 0x1020 0>; >> + power-domains = <&lpass_hm LPASS_CORE_HM_GDSCR>; >> + >> + reg = <0x28100000 0x10000>; >> + reg-names = "lpass-lpaif"; >> + #sound-dai-cells = <1>; >> + qcom,adsp = <&adsp>; >> + >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + /* Optional to set different MI2S SD lines */ >> + mi2s-quaternary@3 { >> + reg = <MI2S_QUATERNARY>; >> + qcom,playback-sd-lines = <0 1>; >> + }; >> -- >> Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc., >> is a member of Code Aurora Forum, a Linux Foundation Collaborative Project. Thanks, Rohit
diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt deleted file mode 100644 index 04e34cc..00000000 --- a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt +++ /dev/null @@ -1,80 +0,0 @@ -* Qualcomm Technologies LPASS CPU DAI - -This node models the Qualcomm Technologies Low-Power Audio SubSystem (LPASS). - -Required properties: - -- compatible : "qcom,lpass-cpu" or "qcom,apq8016-lpass-cpu" or - "qcom,lpass-cpu-sc7180" -- clocks : Must contain an entry for each entry in clock-names. -- clock-names : A list which must include the following entries: - * "ahbix-clk" - * "mi2s-osr-clk" - * "mi2s-bit-clk" - : required clocks for "qcom,lpass-cpu-apq8016" - * "ahbix-clk" - * "mi2s-bit-clk0" - * "mi2s-bit-clk1" - * "mi2s-bit-clk2" - * "mi2s-bit-clk3" - * "pcnoc-mport-clk" - * "pcnoc-sway-clk" - -- interrupts : Must contain an entry for each entry in - interrupt-names. -- interrupt-names : A list which must include the following entries: - * "lpass-irq-lpaif" -- pinctrl-N : One property must exist for each entry in - pinctrl-names. See ../pinctrl/pinctrl-bindings.txt - for details of the property values. -- pinctrl-names : Must contain a "default" entry. -- reg : Must contain an address for each entry in reg-names. -- reg-names : A list which must include the following entries: - * "lpass-lpaif" -- #address-cells : Must be 1 -- #size-cells : Must be 0 - - - -Optional properties: - -- qcom,adsp : Phandle for the audio DSP node - -By default, the driver uses up to 4 MI2S SD lines, for a total of 8 channels. -The SD lines to use can be configured by adding subnodes for each of the DAIs. - -Required properties for each DAI (represented by a subnode): -- reg : Must be one of the DAI IDs - (usually part of dt-bindings header) -- qcom,playback-sd-lines: List of serial data lines to use for playback - Each SD line should be represented by a number from 0-3. -- qcom,capture-sd-lines : List of serial data lines to use for capture - Each SD line should be represented by a number from 0-3. - -Note that adding a subnode changes the default to "no lines configured", -so both playback and capture lines should be configured when a subnode is added. - -Example: - -lpass@28100000 { - compatible = "qcom,lpass-cpu"; - clocks = <&lcc AHBIX_CLK>, <&lcc MI2S_OSR_CLK>, <&lcc MI2S_BIT_CLK>; - clock-names = "ahbix-clk", "mi2s-osr-clk", "mi2s-bit-clk"; - interrupts = <0 85 1>; - interrupt-names = "lpass-irq-lpaif"; - pinctrl-names = "default", "idle"; - pinctrl-0 = <&mi2s_default>; - pinctrl-1 = <&mi2s_idle>; - reg = <0x28100000 0x10000>; - reg-names = "lpass-lpaif"; - qcom,adsp = <&adsp>; - - #address-cells = <1>; - #size-cells = <0>; - - /* Optional to set different MI2S SD lines */ - dai@3 { - reg = <MI2S_QUATERNARY>; - qcom,playback-sd-lines = <0 1>; - }; -}; diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml new file mode 100644 index 00000000..9c350bc --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.yaml @@ -0,0 +1,154 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/qcom,lpass-cpu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm LPASS CPU dai driver bindings + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + - Rohit kumar <rohitkr@codeaurora.org> + +description: + Qualcomm SOC Low-Power Audio SubSystem (LPASS) that consist of MI2S interface + for audio data transfer on external codecs. LPASS cpu driver is a module to + configure Low-Power Audio Interface(LPAIF) core registers across different + IP versions. + +properties: + compatible: + enum: + - qcom,lpass-cpu + - qcom,apq8016-lpass-cpu + - qcom,lpass-cpu-sc7180 + + reg: + items: + - description: LPAIF core registers + + reg-names: + items: + - const: lpass-lpaif + + clocks: + items: + - description: AHBIX core clock + - description: oscillator clock for MI2S external interfaces + - description: Bit clock for single MI2S dai + - description: Bit clock for MI2S_PRIMARY dai interface + - description: Bit clock for MI2S_SECONDARY dai interface + - description: Bit clock for MI2S_TERTIARY dai interface + - description: Bit clock for MI2S_QUATERNARY dai interface + - description: NOC MPORT clock of LPASS core + - description: NOC SWAY clock of LPASS core + + clock-names: + items: + - const: ahbix-clk + - const: mi2s-osr-clk + - const: mi2s-bit-clk + - const: mi2s-bit-clk0 + - const: mi2s-bit-clk1 + - const: mi2s-bit-clk2 + - const: mi2s-bit-clk3 + - const: pcnoc-mport-clk + - const: pcnoc-sway-clk + + interrupts: + items: + - description: LPAIF DMA buffer interrupt + + interrupt-names: + items: + - const: lpass-irq-lpaif + + qcom,adsp: + maxItems: 1 + description: Phandle for the audio DSP node + + iommus: + maxItems: 1 + description: Phandle to apps_smmu node with sid mask + + power-domains: + maxItems: 1 + description: Phandle for power domain node + + '#sound-dai-cells': + const: 1 + + child-node: + description: Required properties for each DAI + type: object + properties: + reg: + description: Must be one of the DAI ID + (Usually part of dtbindings header) + qcom,playback-sd-lines: + description: List of serial data lines to use for playback + Each SD line should be represented by a number from 0-3. + qcom,capture-sd-lines : + description: List of serial data lines to use for capture + Each SD line should be represented by a number from 0-3. + required: + -reg + # Note that adding a subnode changes the default to "no lines configured", + # so both playback and capture lines should be configured when a subnode + # is added. + + +required: + - compatible + - reg + - reg-names + - clocks + - clock-names + - interrupts + - interrupt-names + - sound-dai-cells + +optional: + - qcom,adsp + +if: + properties: + compatible: + contains: + const: qcom,lpass-cpu-sc7180 + +then: + required: + - iommus + - power-domains + +examples: + lpass@28100000 { + compatible = "qcom,lpass-cpu"; + clocks = <&lcc AHBIX_CLK>, + <&lcc MI2S_OSR_CLK>, + <&lcc MI2S_BIT_CLK>; + + clock-names = "ahbix-clk", + "mi2s-osr-clk", + "mi2s-bit-clk"; + + interrupts = <0 85 1>; + interrupt-names = "lpass-irq-lpaif"; + + iommus = <&apps_smmu 0x1020 0>; + power-domains = <&lpass_hm LPASS_CORE_HM_GDSCR>; + + reg = <0x28100000 0x10000>; + reg-names = "lpass-lpaif"; + #sound-dai-cells = <1>; + qcom,adsp = <&adsp>; + + #address-cells = <1>; + #size-cells = <0>; + + /* Optional to set different MI2S SD lines */ + mi2s-quaternary@3 { + reg = <MI2S_QUATERNARY>; + qcom,playback-sd-lines = <0 1>; + };