diff mbox

[v3,2/2] ASoC: Intel: add machine driver for BYT/CHT + ES8316

Message ID 20170605201637.4901-2-drake@endlessm.com (mailing list archive)
State Accepted
Commit a03bdaa565cbf23fa86697727a7d2bf1465e7a03
Headers show

Commit Message

Daniel Drake June 5, 2017, 8:16 p.m. UTC
Add new machine driver, tested with Weibu F3C MiniPC.

Based heavily on code provided by David Yang @ Everest, and other
machine drivers in the same directory.

Signed-off-by: David Yang <yangxiaohua@everest-semi.com>
[drake@endlessm.com: cleanups and modernization]
Signed-off-by: Daniel Drake <drake@endlessm.com>
---

Notes:
    v3:
     - fix inverted logic when checking clk_prepare_enable result
     - update for recent sst_acpi.c changes
    
    v2:
     - add sign-off from David Yang
     - fix bytbyt typo
     - mention that BYT-CR/SSP0 is not supported
     - mention which mic was tested
     - setup clocks at init time, avoids need for platform clock control

 sound/soc/intel/Kconfig                |  12 ++
 sound/soc/intel/atom/sst/sst_acpi.c    |   7 +
 sound/soc/intel/boards/Makefile        |   2 +
 sound/soc/intel/boards/bytcht_es8316.c | 300 +++++++++++++++++++++++++++++++++
 4 files changed, 321 insertions(+)
 create mode 100644 sound/soc/intel/boards/bytcht_es8316.c
diff mbox

Patch

diff --git a/sound/soc/intel/Kconfig b/sound/soc/intel/Kconfig
index a9c50d022e73..35a6a5c55914 100644
--- a/sound/soc/intel/Kconfig
+++ b/sound/soc/intel/Kconfig
@@ -214,6 +214,18 @@  config SND_SOC_INTEL_BYT_CHT_DA7213_MACH
 	  platforms with DA7212/7213 audio codec.
 	  If unsure select "N".
 
+config SND_SOC_INTEL_BYT_CHT_ES8316_MACH
+	tristate "ASoC Audio driver for Intel Baytrail & Cherrytrail with ES8316 codec"
+	depends on X86_INTEL_LPSS && I2C && ACPI
+	select SND_SOC_ES8316
+	select SND_SST_ATOM_HIFI2_PLATFORM
+	select SND_SST_IPC_ACPI
+	select SND_SOC_INTEL_SST_MATCH if ACPI
+	help
+	  This adds support for ASoC machine driver for Intel(R) Baytrail &
+	  Cherrytrail platforms with ES8316 audio codec.
+	  If unsure select "N".
+
 config SND_SOC_INTEL_BYT_CHT_NOCODEC_MACH
 	tristate "ASoC Audio driver for Intel Baytrail & Cherrytrail platform with no codec (MinnowBoard MAX, Up)"
 	depends on X86_INTEL_LPSS && I2C && ACPI
diff --git a/sound/soc/intel/atom/sst/sst_acpi.c b/sound/soc/intel/atom/sst/sst_acpi.c
index 592f6afaf2a5..ff96d1ad3d4e 100644
--- a/sound/soc/intel/atom/sst/sst_acpi.c
+++ b/sound/soc/intel/atom/sst/sst_acpi.c
@@ -625,6 +625,13 @@  static struct sst_acpi_mach sst_acpi_chv[] = {
 		.board = "bytcht_da7213",
 		.pdata = &chv_platform_data
 	},
+	{
+		.id = "ESSX8316",
+		.drv_name = "bytcht_es8316",
+		.fw_filename = "intel/fw_sst_22a8.bin",
+		.board = "bytcht_es8316",
+		.pdata = &chv_platform_data
+	},
 	/* some CHT-T platforms rely on RT5640, use Baytrail machine driver */
 	{
 		.id = "10EC5640",
diff --git a/sound/soc/intel/boards/Makefile b/sound/soc/intel/boards/Makefile
index c92ebcac0222..c4e986f03ec9 100644
--- a/sound/soc/intel/boards/Makefile
+++ b/sound/soc/intel/boards/Makefile
@@ -11,6 +11,7 @@  snd-soc-sst-cht-bsw-rt5672-objs := cht_bsw_rt5672.o
 snd-soc-sst-cht-bsw-rt5645-objs := cht_bsw_rt5645.o
 snd-soc-sst-cht-bsw-max98090_ti-objs := cht_bsw_max98090_ti.o
 snd-soc-sst-byt-cht-da7213-objs := bytcht_da7213.o
+snd-soc-sst-byt-cht-es8316-objs := bytcht_es8316.o
 snd-soc-sst-byt-cht-nocodec-objs := bytcht_nocodec.o
 snd-soc-kbl_rt5663_max98927-objs := kbl_rt5663_max98927.o
 snd-soc-skl_rt286-objs := skl_rt286.o
@@ -30,6 +31,7 @@  obj-$(CONFIG_SND_SOC_INTEL_CHT_BSW_RT5672_MACH) += snd-soc-sst-cht-bsw-rt5672.o
 obj-$(CONFIG_SND_SOC_INTEL_CHT_BSW_RT5645_MACH) += snd-soc-sst-cht-bsw-rt5645.o
 obj-$(CONFIG_SND_SOC_INTEL_CHT_BSW_MAX98090_TI_MACH) += snd-soc-sst-cht-bsw-max98090_ti.o
 obj-$(CONFIG_SND_SOC_INTEL_BYT_CHT_DA7213_MACH) += snd-soc-sst-byt-cht-da7213.o
+obj-$(CONFIG_SND_SOC_INTEL_BYT_CHT_ES8316_MACH) += snd-soc-sst-byt-cht-es8316.o
 obj-$(CONFIG_SND_SOC_INTEL_BYT_CHT_NOCODEC_MACH) += snd-soc-sst-byt-cht-nocodec.o
 obj-$(CONFIG_SND_SOC_INTEL_KBL_RT5663_MAX98927_MACH) += snd-soc-kbl_rt5663_max98927.o
 obj-$(CONFIG_SND_SOC_INTEL_SKL_RT286_MACH) += snd-soc-skl_rt286.o
diff --git a/sound/soc/intel/boards/bytcht_es8316.c b/sound/soc/intel/boards/bytcht_es8316.c
new file mode 100644
index 000000000000..52635462dac6
--- /dev/null
+++ b/sound/soc/intel/boards/bytcht_es8316.c
@@ -0,0 +1,300 @@ 
+/*
+ *  bytcht_es8316.c - ASoc Machine driver for Intel Baytrail/Cherrytrail
+ *                    platforms with Everest ES8316 SoC
+ *
+ *  Copyright (C) 2017 Endless Mobile, Inc.
+ *  Authors: David Yang <yangxiaohua@everest-semi.com>,
+ *           Daniel Drake <drake@endlessm.com>
+ *
+ *  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; version 2 of the License.
+ *
+ *  This program is distributed in the hope that it will be useful, but
+ *  WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ *  General Public License for more details.
+ *
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <asm/platform_sst_audio.h>
+#include <linux/clk.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include "../atom/sst-atom-controls.h"
+#include "../common/sst-acpi.h"
+#include "../common/sst-dsp.h"
+
+struct byt_cht_es8316_private {
+	struct clk *mclk;
+};
+
+#define CODEC_DAI1	"ES8316 HiFi"
+
+static inline struct snd_soc_dai *get_codec_dai(struct snd_soc_card *card)
+{
+	struct snd_soc_pcm_runtime *rtd;
+
+	list_for_each_entry(rtd, &card->rtd_list, list) {
+		if (!strncmp(rtd->codec_dai->name, CODEC_DAI1,
+			     strlen(CODEC_DAI1)))
+			return rtd->codec_dai;
+	}
+	return NULL;
+}
+
+static const struct snd_soc_dapm_widget byt_cht_es8316_widgets[] = {
+	SND_SOC_DAPM_HP("Headphone", NULL),
+
+	/*
+	 * The codec supports two analog microphone inputs. I have only
+	 * tested MIC1. A DMIC route could also potentially be added
+	 * if such functionality is found on another platform.
+	 */
+	SND_SOC_DAPM_MIC("Microphone 1", NULL),
+	SND_SOC_DAPM_MIC("Microphone 2", NULL),
+};
+
+static const struct snd_soc_dapm_route byt_cht_es8316_audio_map[] = {
+	{"MIC1", NULL, "Microphone 1"},
+	{"MIC2", NULL, "Microphone 2"},
+
+	{"Headphone", NULL, "HPOL"},
+	{"Headphone", NULL, "HPOR"},
+
+	{"Playback", NULL, "ssp2 Tx"},
+	{"ssp2 Tx", NULL, "codec_out0"},
+	{"ssp2 Tx", NULL, "codec_out1"},
+	{"codec_in0", NULL, "ssp2 Rx" },
+	{"codec_in1", NULL, "ssp2 Rx" },
+	{"ssp2 Rx", NULL, "Capture"},
+};
+
+static const struct snd_kcontrol_new byt_cht_es8316_controls[] = {
+	SOC_DAPM_PIN_SWITCH("Headphone"),
+	SOC_DAPM_PIN_SWITCH("Microphone 1"),
+	SOC_DAPM_PIN_SWITCH("Microphone 2"),
+};
+
+static int byt_cht_es8316_init(struct snd_soc_pcm_runtime *runtime)
+{
+	struct snd_soc_card *card = runtime->card;
+	struct byt_cht_es8316_private *priv = snd_soc_card_get_drvdata(card);
+	int ret;
+
+	card->dapm.idle_bias_off = true;
+
+	/*
+	 * The firmware might enable the clock at boot (this information
+	 * may or may not be reflected in the enable clock register).
+	 * To change the rate we must disable the clock first to cover these
+	 * cases. Due to common clock framework restrictions that do not allow
+	 * to disable a clock that has not been enabled, we need to enable
+	 * the clock first.
+	 */
+	ret = clk_prepare_enable(priv->mclk);
+	if (!ret)
+		clk_disable_unprepare(priv->mclk);
+
+	ret = clk_set_rate(priv->mclk, 19200000);
+	if (ret)
+		dev_err(card->dev, "unable to set MCLK rate\n");
+
+	ret = clk_prepare_enable(priv->mclk);
+	if (ret)
+		dev_err(card->dev, "unable to enable MCLK\n");
+
+	ret = snd_soc_dai_set_sysclk(runtime->codec_dai, 0, 19200000,
+				     SND_SOC_CLOCK_IN);
+	if (ret < 0) {
+		dev_err(card->dev, "can't set codec clock %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct snd_soc_pcm_stream byt_cht_es8316_dai_params = {
+	.formats = SNDRV_PCM_FMTBIT_S24_LE,
+	.rate_min = 48000,
+	.rate_max = 48000,
+	.channels_min = 2,
+	.channels_max = 2,
+};
+
+static int byt_cht_es8316_codec_fixup(struct snd_soc_pcm_runtime *rtd,
+			    struct snd_pcm_hw_params *params)
+{
+	struct snd_interval *rate = hw_param_interval(params,
+			SNDRV_PCM_HW_PARAM_RATE);
+	struct snd_interval *channels = hw_param_interval(params,
+						SNDRV_PCM_HW_PARAM_CHANNELS);
+	int ret;
+
+	/* The DSP will covert the FE rate to 48k, stereo */
+	rate->min = rate->max = 48000;
+	channels->min = channels->max = 2;
+
+	/* set SSP2 to 24-bit */
+	params_set_format(params, SNDRV_PCM_FORMAT_S24_LE);
+
+	/*
+	 * Default mode for SSP configuration is TDM 4 slot, override config
+	 * with explicit setting to I2S 2ch 24-bit. The word length is set with
+	 * dai_set_tdm_slot() since there is no other API exposed
+	 */
+	ret = snd_soc_dai_set_fmt(rtd->cpu_dai,
+				SND_SOC_DAIFMT_I2S     |
+				SND_SOC_DAIFMT_NB_NF   |
+				SND_SOC_DAIFMT_CBS_CFS
+		);
+	if (ret < 0) {
+		dev_err(rtd->dev, "can't set format to I2S, err %d\n", ret);
+		return ret;
+	}
+
+	ret = snd_soc_dai_set_tdm_slot(rtd->cpu_dai, 0x3, 0x3, 2, 24);
+	if (ret < 0) {
+		dev_err(rtd->dev, "can't set I2S config, err %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int byt_cht_es8316_aif1_startup(struct snd_pcm_substream *substream)
+{
+	return snd_pcm_hw_constraint_single(substream->runtime,
+			SNDRV_PCM_HW_PARAM_RATE, 48000);
+}
+
+static const struct snd_soc_ops byt_cht_es8316_aif1_ops = {
+	.startup = byt_cht_es8316_aif1_startup,
+};
+
+static struct snd_soc_dai_link byt_cht_es8316_dais[] = {
+	[MERR_DPCM_AUDIO] = {
+		.name = "Audio Port",
+		.stream_name = "Audio",
+		.cpu_dai_name = "media-cpu-dai",
+		.codec_dai_name = "snd-soc-dummy-dai",
+		.codec_name = "snd-soc-dummy",
+		.platform_name = "sst-mfld-platform",
+		.nonatomic = true,
+		.dynamic = 1,
+		.dpcm_playback = 1,
+		.dpcm_capture = 1,
+		.ops = &byt_cht_es8316_aif1_ops,
+	},
+
+	[MERR_DPCM_DEEP_BUFFER] = {
+		.name = "Deep-Buffer Audio Port",
+		.stream_name = "Deep-Buffer Audio",
+		.cpu_dai_name = "deepbuffer-cpu-dai",
+		.codec_dai_name = "snd-soc-dummy-dai",
+		.codec_name = "snd-soc-dummy",
+		.platform_name = "sst-mfld-platform",
+		.nonatomic = true,
+		.dynamic = 1,
+		.dpcm_playback = 1,
+		.ops = &byt_cht_es8316_aif1_ops,
+	},
+
+	[MERR_DPCM_COMPR] = {
+		.name = "Compressed Port",
+		.stream_name = "Compress",
+		.cpu_dai_name = "compress-cpu-dai",
+		.codec_dai_name = "snd-soc-dummy-dai",
+		.codec_name = "snd-soc-dummy",
+		.platform_name = "sst-mfld-platform",
+	},
+
+		/* back ends */
+	{
+		/* Only SSP2 has been tested here, so BYT-CR platforms that
+		 * require SSP0 will not work.
+		 */
+		.name = "SSP2-Codec",
+		.id = 1,
+		.cpu_dai_name = "ssp2-port",
+		.platform_name = "sst-mfld-platform",
+		.no_pcm = 1,
+		.codec_dai_name = "ES8316 HiFi",
+		.codec_name = "i2c-ESSX8316:00",
+		.dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF
+						| SND_SOC_DAIFMT_CBS_CFS,
+		.be_hw_params_fixup = byt_cht_es8316_codec_fixup,
+		.nonatomic = true,
+		.dpcm_playback = 1,
+		.dpcm_capture = 1,
+		.init = byt_cht_es8316_init,
+	},
+};
+
+
+/* SoC card */
+static struct snd_soc_card byt_cht_es8316_card = {
+	.name = "bytcht-es8316",
+	.owner = THIS_MODULE,
+	.dai_link = byt_cht_es8316_dais,
+	.num_links = ARRAY_SIZE(byt_cht_es8316_dais),
+	.dapm_widgets = byt_cht_es8316_widgets,
+	.num_dapm_widgets = ARRAY_SIZE(byt_cht_es8316_widgets),
+	.dapm_routes = byt_cht_es8316_audio_map,
+	.num_dapm_routes = ARRAY_SIZE(byt_cht_es8316_audio_map),
+	.controls = byt_cht_es8316_controls,
+	.num_controls = ARRAY_SIZE(byt_cht_es8316_controls),
+	.fully_routed = true,
+};
+
+static int snd_byt_cht_es8316_mc_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct byt_cht_es8316_private *priv;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_ATOMIC);
+	if (!priv)
+		return -ENOMEM;
+
+	/* register the soc card */
+	byt_cht_es8316_card.dev = &pdev->dev;
+	snd_soc_card_set_drvdata(&byt_cht_es8316_card, priv);
+
+	priv->mclk = devm_clk_get(&pdev->dev, "pmc_plt_clk_3");
+	if (IS_ERR(priv->mclk)) {
+		ret = PTR_ERR(priv->mclk);
+		dev_err(&pdev->dev,
+			"Failed to get MCLK from pmc_plt_clk_3: %d\n",
+			ret);
+		return ret;
+	}
+
+	ret = devm_snd_soc_register_card(&pdev->dev, &byt_cht_es8316_card);
+	if (ret) {
+		dev_err(&pdev->dev, "snd_soc_register_card failed %d\n", ret);
+		return ret;
+	}
+	platform_set_drvdata(pdev, &byt_cht_es8316_card);
+	return ret;
+}
+
+static struct platform_driver snd_byt_cht_es8316_mc_driver = {
+	.driver = {
+		.name = "bytcht_es8316",
+	},
+	.probe = snd_byt_cht_es8316_mc_probe,
+};
+
+module_platform_driver(snd_byt_cht_es8316_mc_driver);
+MODULE_DESCRIPTION("ASoC Intel(R) Baytrail/Cherrytrail Machine driver");
+MODULE_AUTHOR("David Yang <yangxiaohua@everest-semi.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:bytcht_es8316");