@@ -673,7 +673,7 @@ static int adcx140_set_dai_fmt(struct snd_soc_dai *codec_dai,
u8 iface_reg1 = 0;
u8 iface_reg2 = 0;
int offset = 0;
- int width = adcx140->slot_width;
+ bool inverted_bclk = false;
/* set master/slave audio interface */
switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
@@ -689,24 +689,6 @@ static int adcx140_set_dai_fmt(struct snd_soc_dai *codec_dai,
return -EINVAL;
}
- /* signal polarity */
- switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
- case SND_SOC_DAIFMT_NB_IF:
- iface_reg1 |= ADCX140_FSYNCINV_BIT;
- break;
- case SND_SOC_DAIFMT_IB_IF:
- iface_reg1 |= ADCX140_BCLKINV_BIT | ADCX140_FSYNCINV_BIT;
- break;
- case SND_SOC_DAIFMT_IB_NF:
- iface_reg1 |= ADCX140_BCLKINV_BIT;
- break;
- case SND_SOC_DAIFMT_NB_NF:
- break;
- default:
- dev_err(component->dev, "Invalid DAI clock signal polarity\n");
- return -EINVAL;
- }
-
/* interface format */
switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
case SND_SOC_DAIFMT_I2S:
@@ -716,16 +698,36 @@ static int adcx140_set_dai_fmt(struct snd_soc_dai *codec_dai,
iface_reg1 |= ADCX140_LEFT_JUST_BIT;
break;
case SND_SOC_DAIFMT_DSP_A:
- offset += (adcx140->tdm_delay * width + 1);
+ offset = 1;
+ inverted_bclk = true;
break;
case SND_SOC_DAIFMT_DSP_B:
- offset += adcx140->tdm_delay * width;
+ inverted_bclk = true;
break;
default:
dev_err(component->dev, "Invalid DAI interface format\n");
return -EINVAL;
}
+ /* signal polarity */
+ switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+ case SND_SOC_DAIFMT_IB_NF:
+ case SND_SOC_DAIFMT_IB_IF:
+ inverted_bclk = !inverted_bclk;
+ break;
+ case SND_SOC_DAIFMT_NB_IF:
+ iface_reg1 |= ADCX140_FSYNCINV_BIT;
+ break;
+ case SND_SOC_DAIFMT_NB_NF:
+ break;
+ default:
+ dev_err(component->dev, "Invalid DAI clock signal polarity\n");
+ return -EINVAL;
+ }
+
+ if (inverted_bclk)
+ iface_reg1 |= ADCX140_BCLKINV_BIT;
+
adcx140->dai_fmt = fmt & SND_SOC_DAIFMT_FORMAT_MASK;
adcx140_pwr_ctrl(adcx140, false);
Fix the BCLK inversion for DSP modes This is how it is defined by ASoC: * BCLK: * - "normal" polarity means signal is available at rising edge of BCLK * - "inverted" polarity means signal is available at falling edge of BCLK The adcx140 defines the BCLK edge based on coding type. The PCM (DSP_A/B) should drive on rising and sample on falling edge, so from ASoC pov, it is IB_NF. But from the codec pov if it is configured in DSP mode, then the BCLK should not be inverted, defaults to the coding standard. For i2s, it is NB_NF from ASoC pov (drive on falling, sample on rising). From the codec's pov BCLK should not invert either, as this is the default for the coding. So, inversion must take the format into account: IB_NF + DSP_A/B == the codec bclk inversion should be disabled NB_NF + DSP_A/B == the codec bclk inversion should be enabled NB_NF + I2S == the codec bclk inversion should be disabled Signed-off-by: Dan Murphy <dmurphy@ti.com> --- sound/soc/codecs/tlv320adcx140.c | 44 +++++++++++++++++--------------- 1 file changed, 23 insertions(+), 21 deletions(-)