new file mode 100644
@@ -0,0 +1,194 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/wlf,wm8994.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Wolfson WM1811/WM8994/WM8958 audio codecs
+
+maintainers:
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+ - patches@opensource.cirrus.com
+
+description: |
+ These devices support both I2C and SPI (configured with pin strapping on the
+ board).
+
+ Pins on the device (for linking into audio routes):
+ IN1LN, IN1LP, IN2LN, IN2LP:VXRN, IN1RN, IN1RP, IN2RN, IN2RP:VXRP, SPKOUTLP,
+ SPKOUTLN, SPKOUTRP, SPKOUTRN, HPOUT1L, HPOUT1R, HPOUT2P, HPOUT2N, LINEOUT1P,
+ LINEOUT1N, LINEOUT2P, LINEOUT2N.
+
+properties:
+ compatible:
+ enum:
+ - wlf,wm1811
+ - wlf,wm8994
+ - wlf,wm8958
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ minItems: 1
+ maxItems: 2
+
+ clock-names:
+ minItems: 1
+ items:
+ - const: MCLK1
+ - const: MCLK2
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 2
+ description:
+ The first cell is the IRQ number. The second cell is the flags, encoded
+ as the trigger masks.
+
+ AVDD1-supply: true
+ AVDD2-supply: true
+ CPVDD-supply: true
+ DBVDD-supply: true
+ DBVDD1-supply: true
+ DBVDD2-supply: true
+ DBVDD3-supply: true
+ DCVDD-supply: true
+ LDO1VDD-supply: true
+ LDO2VDD-supply: true
+ SPKVDD1-supply: true
+ SPKVDD2-supply: true
+
+ '#sound-dai-cells':
+ const: 0
+
+ wlf,gpio-cfg:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ maxItems: 11
+ description:
+ A list of GPIO configuration register values. If absent, no configuration
+ of these registers is performed. If any value is over 0xffff then the
+ register will be left as default. If present 11 values must be supplied.
+
+ wlf,micbias-cfg:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ maxItems: 2
+ description:
+ Two MICBIAS register values for WM1811 or WM8958. If absent the register
+ defaults will be used.
+
+ wlf,ldo1ena-gpios:
+ maxItems: 1
+ description:
+ Control of LDO1ENA input to device.
+
+ wlf,ldo2ena-gpios:
+ maxItems: 1
+ description:
+ Control of LDO2ENA input to device.
+
+ wlf,lineout1-se:
+ type: boolean
+ description:
+ LINEOUT1 is in single ended mode.
+
+ wlf,lineout2-se:
+ type: boolean
+ description:
+ INEOUT2 is in single ended mode.
+
+ wlf,lineout1-feedback:
+ type: boolean
+ description:
+ LINEOUT1 has common mode feedback connected.
+
+ wlf,lineout2-feedback:
+ type: boolean
+ description:
+ LINEOUT2 has common mode feedback connected.
+
+ wlf,ldoena-always-driven:
+ type: boolean
+ description:
+ LDOENA is always driven.
+
+ wlf,spkmode-pu:
+ type: boolean
+ description:
+ Enable the internal pull-up resistor on the SPKMODE pin.
+
+ wlf,csnaddr-pd:
+ type: boolean
+ description:
+ Enable the internal pull-down resistor on the CS/ADDR pin.
+
+required:
+ - compatible
+ - reg
+ - AVDD2-supply
+ - CPVDD-supply
+ - SPKVDD1-supply
+ - SPKVDD2-supply
+
+allOf:
+ - $ref: dai-common.yaml#
+ - if:
+ properties:
+ compatible:
+ enum:
+ - wlf,wm1811
+ - wlf,wm8958
+ then:
+ properties:
+ DBVDD-supply: false
+ LDO2VDD-supply: false
+ required:
+ - DBVDD1-supply
+ - DBVDD2-supply
+ - DBVDD3-supply
+ else:
+ properties:
+ DBVDD1-supply: false
+ DBVDD2-supply: false
+ DBVDD3-supply: false
+ required:
+ - DBVDD-supply
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ audio-codec@1a {
+ compatible = "wlf,wm1811";
+ reg = <0x1a>;
+ clocks = <&i2s0 0>;
+ clock-names = "MCLK1";
+
+ AVDD2-supply = <&main_dc_reg>;
+ CPVDD-supply = <&main_dc_reg>;
+ DBVDD1-supply = <&main_dc_reg>;
+ DBVDD2-supply = <&main_dc_reg>;
+ DBVDD3-supply = <&main_dc_reg>;
+ LDO1VDD-supply = <&main_dc_reg>;
+ SPKVDD1-supply = <&main_dc_reg>;
+ SPKVDD2-supply = <&main_dc_reg>;
+
+ wlf,ldo1ena-gpios = <&gpb0 0 GPIO_ACTIVE_HIGH>;
+ wlf,ldo2ena-gpios = <&gpb0 1 GPIO_ACTIVE_HIGH>;
+ };
+ };
deleted file mode 100644
@@ -1,112 +0,0 @@
-WM1811/WM8994/WM8958 audio CODEC
-
-These devices support both I2C and SPI (configured with pin strapping
-on the board).
-
-Required properties:
-
- - compatible : One of "wlf,wm1811", "wlf,wm8994" or "wlf,wm8958".
-
- - reg : the I2C address of the device for I2C, the chip select
- number for SPI.
-
- - gpio-controller : Indicates this device is a GPIO controller.
- - #gpio-cells : Must be 2. The first cell is the pin number and the
- second cell is used to specify optional parameters (currently unused).
-
- - power supplies for the device, as covered in
- Documentation/devicetree/bindings/regulator/regulator.txt, depending
- on compatible:
- - for wlf,wm1811 and wlf,wm8958:
- AVDD1-supply, AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply,
- DCVDD-supply, CPVDD-supply, SPKVDD1-supply, SPKVDD2-supply
- - for wlf,wm8994:
- AVDD1-supply, AVDD2-supply, DBVDD-supply, DCVDD-supply, CPVDD-supply,
- SPKVDD1-supply, SPKVDD2-supply
-
-Optional properties:
-
- - interrupts : The interrupt line the IRQ signal for the device is
- connected to. This is optional, if it is not connected then none
- of the interrupt related properties should be specified.
- - interrupt-controller : These devices contain interrupt controllers
- and may provide interrupt services to other devices if they have an
- interrupt line connected.
- - #interrupt-cells: the number of cells to describe an IRQ, this should be 2.
- The first cell is the IRQ number.
- The second cell is the flags, encoded as the trigger masks from
- Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-
- - clocks : A list of up to two phandle and clock specifier pairs
- - clock-names : A list of clock names sorted in the same order as clocks.
- Valid clock names are "MCLK1" and "MCLK2".
-
- - wlf,gpio-cfg : A list of GPIO configuration register values. If absent,
- no configuration of these registers is performed. If any value is
- over 0xffff then the register will be left as default. If present 11
- values must be supplied.
-
- - wlf,micbias-cfg : Two MICBIAS register values for WM1811 or
- WM8958. If absent the register defaults will be used.
-
- - wlf,ldo1ena : GPIO specifier for control of LDO1ENA input to device.
- - wlf,ldo2ena : GPIO specifier for control of LDO2ENA input to device.
-
- - wlf,lineout1-se : If present LINEOUT1 is in single ended mode.
- - wlf,lineout2-se : If present LINEOUT2 is in single ended mode.
-
- - wlf,lineout1-feedback : If present LINEOUT1 has common mode feedback
- connected.
- - wlf,lineout2-feedback : If present LINEOUT2 has common mode feedback
- connected.
-
- - wlf,ldoena-always-driven : If present LDOENA is always driven.
-
- - wlf,spkmode-pu : If present enable the internal pull-up resistor on
- the SPKMODE pin.
-
- - wlf,csnaddr-pd : If present enable the internal pull-down resistor on
- the CS/ADDR pin.
-
-Pins on the device (for linking into audio routes):
-
- * IN1LN
- * IN1LP
- * IN2LN
- * IN2LP:VXRN
- * IN1RN
- * IN1RP
- * IN2RN
- * IN2RP:VXRP
- * SPKOUTLP
- * SPKOUTLN
- * SPKOUTRP
- * SPKOUTRN
- * HPOUT1L
- * HPOUT1R
- * HPOUT2P
- * HPOUT2N
- * LINEOUT1P
- * LINEOUT1N
- * LINEOUT2P
- * LINEOUT2N
-
-Example:
-
-wm8994: codec@1a {
- compatible = "wlf,wm8994";
- reg = <0x1a>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- lineout1-se;
-
- AVDD1-supply = <®ulator>;
- AVDD2-supply = <®ulator>;
- CPVDD-supply = <®ulator>;
- DBVDD-supply = <®ulator>;
- DCVDD-supply = <®ulator>;
- SPKVDD1-supply = <®ulator>;
- SPKVDD2-supply = <®ulator>;
-};