| Message ID | 20241020083124.174724-2-ryan@testtoast.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | ASoC: add Allwinner H616 audio codec support | expand |
On Sun, 20 Oct 2024 21:30:51 +1300 Ryan Walklin <ryan@testtoast.com> wrote: Hi, > Allwinner has previously released a H616 audio driver which also > provides sigma-delta modulation for the audio PLL clocks. This approach > is used in other Allwinner SoCs, including the H3 and A64. > > The manual-provided clock values are: > PLL_AUDIO(hs) = 24 MHz*N/M1 > PLL_AUDIO(4X) = 24 MHz*N/M0/M1/P > PLL_AUDIO(2X) = 24 MHz*N/M0/M1/P/2 > PLL_AUDIO(1X) = 24 MHz*N/M0/M1/P/4 > > A fixed post-divider of 2 is used to account for a fixed M0 divider of > 2 (taken from the vendor BSP driver). The real reason seems to be that our existing macros and struct cannot model those extra dividers, and using M0=2 gives better results, so we fix that in the probe routine and account for that using the fixed post-div. > Using SDM allows correction of the PLL_AUDIO_(4,2,1)X clock fixed > dividers to the datasheet-specified values of 1/2/4 respectively. As mentioned below, SDM has nothing to do with those simple dividers clocks, it's just there to reach the "odd" base audio frequency more accurately. > > Add SDM to the H616 clock control unit driver. > > Signed-off-by: Ryan Walklin <ryan@testtoast.com> > > --- > Changelog v1..v2: > - Add fixed_post_div to high-speed audio clock to correct M0 value to 1 (ie divide by 2) based on manual > - Correct PLL_AUDIO_(4/2/1)X clocks to manual-provided values > - Add/correct inline comments for the above. > - add CCU_FEATURE_FIXED_POSTDIV to pll_audio_hs_clk.common.features > --- > drivers/clk/sunxi-ng/ccu-sun50i-h616.c | 44 ++++++++++++++++---------- > 1 file changed, 28 insertions(+), 16 deletions(-) > > diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h616.c b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c > index 6c7623d4c59ea..42feaaf5a59c6 100644 > --- a/drivers/clk/sunxi-ng/ccu-sun50i-h616.c > +++ b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c > @@ -215,20 +215,28 @@ static struct ccu_nkmp pll_de_clk = { > }, > }; > > -/* > - * TODO: Determine SDM settings for the audio PLL. The manual suggests > - * PLL_FACTOR_N=16, PLL_POST_DIV_P=2, OUTPUT_DIV=2, pattern=0xe000c49b > - * for 24.576 MHz, and PLL_FACTOR_N=22, PLL_POST_DIV_P=3, OUTPUT_DIV=2, > - * pattern=0xe001288c for 22.5792 MHz. > - * This clashes with our fixed PLL_POST_DIV_P. > +/* > + * Sigma-delta modulation settings table obtained from the vendor SDK driver. > + * There are additional M0 and M1 divider bits not modelled here, so forced to > + * fixed values in the probe routine. > */ > +static struct ccu_sdm_setting pll_audio_sdm_table[] = { > + { .rate = 90316800, .pattern = 0xc001288d, .m = 3, .n = 22 }, > + { .rate = 98304000, .pattern = 0xc001eb85, .m = 5, .n = 40 }, It's a bit strange to see odd dividers here, since the manual "warns" against this, because it's causing a non-50% duty cycle. But apparently the audio codec is fine with this (given it works)? Or does this apply to the product of all the dividers (m * m0 * m1), so our m0=2 fixes that? And for the records, the numbers calculate like this (with SDM): rate = 24MHz * (n + pattern[16:0] / 2^17) / m / m0 / m1 which gives 90316802 Hz and 98303997 Hz with those numbers, respectively. > +}; > + > #define SUN50I_H616_PLL_AUDIO_REG 0x078 > static struct ccu_nm pll_audio_hs_clk = { > .enable = BIT(31), > .lock = BIT(28), > .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), > - .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ > + .m = _SUNXI_CCU_DIV(16, 6), > + .sdm = _SUNXI_CCU_SDM(pll_audio_sdm_table, > + BIT(24), 0x178, BIT(31)), > + .fixed_post_div = 2, > .common = { > + .features = CCU_FEATURE_FIXED_POSTDIV | > + CCU_FEATURE_SIGMA_DELTA_MOD, > .reg = 0x078, > .hw.init = CLK_HW_INIT("pll-audio-hs", "osc24M", > &ccu_nm_ops, > @@ -701,18 +709,20 @@ static const struct clk_hw *clk_parent_pll_audio[] = { > }; > > /* > - * The divider of pll-audio is fixed to 24 for now, so 24576000 and 22579200 > - * rates can be set exactly in conjunction with sigma-delta modulation. > + * The PLL_AUDIO_4X clock defaults to 24.5714 MHz according to the manual, with The manual says that PLL_AUDIO_1X defaults to 24.5714 MHz (24.576, really?), so PLL_AUDIO_4X (the actual PLL output) should be four times that. > + * a final divider of 1. The 2X and 1X clocks use 2 and 4 respectively. The 1x > + * clock is set to either 24576000 or 22579200 for 48Khz and 44.1Khz (and > + * multiples) in conjunction with sigma-delta modulation. That last part sounds a bit vague, what about: " ... (and multiples). The Sigma-delta modulation bits allow providing a fractional-N divider in the PLL, to help reaching those specific frequencies with less error." But then again this probably belongs more to the PLL_AUDIO_HS clock comment above? Since this here is just to model the simple divider clocks. Anyway, the technical bits seem to add up, and that's what I came up with in my experiments as well. But there are better combinations of N, fractional N, and M to reach the target frequency with less error, and M is also even in those cases. This could be a later optimisation, though. Cheers, Andre > */ > static CLK_FIXED_FACTOR_HWS(pll_audio_1x_clk, "pll-audio-1x", > clk_parent_pll_audio, > - 96, 1, CLK_SET_RATE_PARENT); > + 4, 1, CLK_SET_RATE_PARENT); > static CLK_FIXED_FACTOR_HWS(pll_audio_2x_clk, "pll-audio-2x", > clk_parent_pll_audio, > - 48, 1, CLK_SET_RATE_PARENT); > + 2, 1, CLK_SET_RATE_PARENT); > static CLK_FIXED_FACTOR_HWS(pll_audio_4x_clk, "pll-audio-4x", > clk_parent_pll_audio, > - 24, 1, CLK_SET_RATE_PARENT); > + 1, 1, CLK_SET_RATE_PARENT); > > static const struct clk_hw *pll_periph0_parents[] = { > &pll_periph0_clk.common.hw > @@ -1162,12 +1172,14 @@ static int sun50i_h616_ccu_probe(struct platform_device *pdev) > } > > /* > - * Force the post-divider of pll-audio to 12 and the output divider > - * of it to 2, so 24576000 and 22579200 rates can be set exactly. > + * Set the output-divider for the pll-audio clocks (M0) to 2 and the > + * input divider (M1) to 1 as recommended by the manual when using > + * SDM. > */ > val = readl(reg + SUN50I_H616_PLL_AUDIO_REG); > - val &= ~(GENMASK(21, 16) | BIT(0)); > - writel(val | (11 << 16) | BIT(0), reg + SUN50I_H616_PLL_AUDIO_REG); > + val &= ~BIT(1); > + val |= BIT(0); > + writel(val, reg + SUN50I_H616_PLL_AUDIO_REG); > > /* > * First clock parent (osc32K) is unusable for CEC. But since there
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h616.c b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c index 6c7623d4c59ea..42feaaf5a59c6 100644 --- a/drivers/clk/sunxi-ng/ccu-sun50i-h616.c +++ b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c @@ -215,20 +215,28 @@ static struct ccu_nkmp pll_de_clk = { }, }; -/* - * TODO: Determine SDM settings for the audio PLL. The manual suggests - * PLL_FACTOR_N=16, PLL_POST_DIV_P=2, OUTPUT_DIV=2, pattern=0xe000c49b - * for 24.576 MHz, and PLL_FACTOR_N=22, PLL_POST_DIV_P=3, OUTPUT_DIV=2, - * pattern=0xe001288c for 22.5792 MHz. - * This clashes with our fixed PLL_POST_DIV_P. +/* + * Sigma-delta modulation settings table obtained from the vendor SDK driver. + * There are additional M0 and M1 divider bits not modelled here, so forced to + * fixed values in the probe routine. */ +static struct ccu_sdm_setting pll_audio_sdm_table[] = { + { .rate = 90316800, .pattern = 0xc001288d, .m = 3, .n = 22 }, + { .rate = 98304000, .pattern = 0xc001eb85, .m = 5, .n = 40 }, +}; + #define SUN50I_H616_PLL_AUDIO_REG 0x078 static struct ccu_nm pll_audio_hs_clk = { .enable = BIT(31), .lock = BIT(28), .n = _SUNXI_CCU_MULT_MIN(8, 8, 12), - .m = _SUNXI_CCU_DIV(1, 1), /* input divider */ + .m = _SUNXI_CCU_DIV(16, 6), + .sdm = _SUNXI_CCU_SDM(pll_audio_sdm_table, + BIT(24), 0x178, BIT(31)), + .fixed_post_div = 2, .common = { + .features = CCU_FEATURE_FIXED_POSTDIV | + CCU_FEATURE_SIGMA_DELTA_MOD, .reg = 0x078, .hw.init = CLK_HW_INIT("pll-audio-hs", "osc24M", &ccu_nm_ops, @@ -701,18 +709,20 @@ static const struct clk_hw *clk_parent_pll_audio[] = { }; /* - * The divider of pll-audio is fixed to 24 for now, so 24576000 and 22579200 - * rates can be set exactly in conjunction with sigma-delta modulation. + * The PLL_AUDIO_4X clock defaults to 24.5714 MHz according to the manual, with + * a final divider of 1. The 2X and 1X clocks use 2 and 4 respectively. The 1x + * clock is set to either 24576000 or 22579200 for 48Khz and 44.1Khz (and + * multiples) in conjunction with sigma-delta modulation. */ static CLK_FIXED_FACTOR_HWS(pll_audio_1x_clk, "pll-audio-1x", clk_parent_pll_audio, - 96, 1, CLK_SET_RATE_PARENT); + 4, 1, CLK_SET_RATE_PARENT); static CLK_FIXED_FACTOR_HWS(pll_audio_2x_clk, "pll-audio-2x", clk_parent_pll_audio, - 48, 1, CLK_SET_RATE_PARENT); + 2, 1, CLK_SET_RATE_PARENT); static CLK_FIXED_FACTOR_HWS(pll_audio_4x_clk, "pll-audio-4x", clk_parent_pll_audio, - 24, 1, CLK_SET_RATE_PARENT); + 1, 1, CLK_SET_RATE_PARENT); static const struct clk_hw *pll_periph0_parents[] = { &pll_periph0_clk.common.hw @@ -1162,12 +1172,14 @@ static int sun50i_h616_ccu_probe(struct platform_device *pdev) } /* - * Force the post-divider of pll-audio to 12 and the output divider - * of it to 2, so 24576000 and 22579200 rates can be set exactly. + * Set the output-divider for the pll-audio clocks (M0) to 2 and the + * input divider (M1) to 1 as recommended by the manual when using + * SDM. */ val = readl(reg + SUN50I_H616_PLL_AUDIO_REG); - val &= ~(GENMASK(21, 16) | BIT(0)); - writel(val | (11 << 16) | BIT(0), reg + SUN50I_H616_PLL_AUDIO_REG); + val &= ~BIT(1); + val |= BIT(0); + writel(val, reg + SUN50I_H616_PLL_AUDIO_REG); /* * First clock parent (osc32K) is unusable for CEC. But since there
Allwinner has previously released a H616 audio driver which also provides sigma-delta modulation for the audio PLL clocks. This approach is used in other Allwinner SoCs, including the H3 and A64. The manual-provided clock values are: PLL_AUDIO(hs) = 24 MHz*N/M1 PLL_AUDIO(4X) = 24 MHz*N/M0/M1/P PLL_AUDIO(2X) = 24 MHz*N/M0/M1/P/2 PLL_AUDIO(1X) = 24 MHz*N/M0/M1/P/4 A fixed post-divider of 2 is used to account for a fixed M0 divider of 2 (taken from the vendor BSP driver). Using SDM allows correction of the PLL_AUDIO_(4,2,1)X clock fixed dividers to the datasheet-specified values of 1/2/4 respectively. Add SDM to the H616 clock control unit driver. Signed-off-by: Ryan Walklin <ryan@testtoast.com> --- Changelog v1..v2: - Add fixed_post_div to high-speed audio clock to correct M0 value to 1 (ie divide by 2) based on manual - Correct PLL_AUDIO_(4/2/1)X clocks to manual-provided values - Add/correct inline comments for the above. - add CCU_FEATURE_FIXED_POSTDIV to pll_audio_hs_clk.common.features --- drivers/clk/sunxi-ng/ccu-sun50i-h616.c | 44 ++++++++++++++++---------- 1 file changed, 28 insertions(+), 16 deletions(-)