| Message ID | 20230131043816.4525-1-steev@kali.org (mailing list archive) |
|---|---|
| Headers | show |
| Series | Attempt at adding WCN6855 BT support | expand |
On Mon, 30 Jan 2023 22:38:12 -0600, Steev Klimaszewski wrote: > This v2 of the patchset is somewhat of an RFC/RFT, and also just something to > get this out there. > > First things first, I do not have access to the specs nor the schematics, so a > lot of this was done via guess work, looking at the acpi tables, and looking at > how a similar device (wcn6750) was added. > > [...] Applied, thanks! [1/4] dt-bindings: net: Add WCN6855 Bluetooth (no commit info) [2/4] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6855 (no commit info) [3/4] arm64: dts: qcom: sc8280xp: Define uart2 commit: 9db28f297526f17c6575ec0eefc93a8b1642cff7 [4/4] arm64: dts: qcom: thinkpad-x13s: Add bluetooth (no commit info) Best regards,
This v2 of the patchset is somewhat of an RFC/RFT, and also just something to get this out there. First things first, I do not have access to the specs nor the schematics, so a lot of this was done via guess work, looking at the acpi tables, and looking at how a similar device (wcn6750) was added. There are possibly checkpatch warnings, and I do apologize to those who won't review things until there are no warnings for wasting your time, I did try to correct the ones I came across and seemed to be needed. One example is that I have the vregs commented out, the dt-bindings say that they are required since it's based on the wcn6750 work but also like the 6750, I've added defaults into the driver, and those seem to work, at least for the initial testing. The end result is that we do have a working device, but not entirely reliable. Hopefully by getting this out there, people who do have access to the specs or schematics can see where the improvements or fixes need to come. There are a few things that I am not sure why they happen, and don't have the knowledge level to figure out why they happen or debugging it. Bluetooth: hci0: setting up wcn6855 Bluetooth: hci0: Frame reassembly failed (-84) Bluetooth: hci0: QCA Product ID :0x00000013 Bluetooth: hci0: QCA SOC Version :0x400c0210 Bluetooth: hci0: QCA ROM Version :0x00000201 Bluetooth: hci0: QCA Patch Version:0x000038e6 Bluetooth: hci0: QCA controller version 0x02100201 Bluetooth: hci0: unexpected event for opcode 0xfc48 Bluetooth: hci0: Sending QCA Patch config failed (-110) Bluetooth: hci0: QCA Downloading qca/hpbtfw21.tlv Bluetooth: hci0: QCA Downloading qca/hpnv21g.bin Bluetooth: hci0: QCA setup on UART is completed I do not know why the Frame assembly failed, nor the unexpected event. Likewise, I'm not entirely sure why it says the patch config send times out, and *then* seems to send it? The BD Address also seems to be incorrect, and I'm not sure what is going on there either. Additionally, I've tried with an additional patch that I'm not including that is based on commit 059924fdf6c1 ("Bluetooth: btqca: Use NVM files based on SoC ID for WCN3991") to try using the hpnv21g.bin or hpnv21.bin, and the firmware acted the same regardless, so I am assuming I don't truly need the "g" firmware on my Thinkpad X13s. Testing was done by connecting a Razer Orochi bluetooth mouse, and using it, as well as connecting to and using an H2GO bluetooth speaker and playing audio out via canberra-gtk-play as well as a couple of YouTube videos in a browser. The mouse only seems to work when < 2 ft. from the laptop, and for the speaker, only "A2DP Sink, codec SBC" would provide audio output, and while I could see that data was being sent to the speaker, it wasn't always outputting, and going > 4ft. away, would often disconnect. steev@wintermute:~$ hciconfig -a hci0: Type: Primary Bus: UART BD Address: 00:00:00:00:5A:AD ACL MTU: 1024:8 SCO MTU: 240:4 UP RUNNING PSCAN RX bytes:1492 acl:0 sco:0 events:126 errors:0 TX bytes:128743 acl:0 sco:0 commands:597 errors:0 Features: 0xff 0xfe 0x8f 0xfe 0xd8 0x3f 0x5b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH HOLD SNIFF Link mode: PERIPHERAL ACCEPT Name: 'wintermute' Class: 0x0c010c Service Classes: Rendering, Capturing Device Class: Computer, Laptop HCI Version: (0xc) Revision: 0x0 LMP Version: (0xc) Subversion: 0x46f7 Manufacturer: Qualcomm (29) steev@wintermute:~$ dmesg | grep Razer [ 3089.235440] input: Razer Orochi as /devices/virtual/misc/uhid/0005:1532:0056.0003/input/input11 [ 3089.238580] hid-generic 0005:1532:0056.0003: input,hidraw2: BLUETOOTH HID v0.01 Mouse [Razer Orochi] on 00:00:00:00:5a:ad steev@wintermute:~$ dmesg | grep H2GO [ 3140.959947] input: H2GO Speaker (AVRCP) as /devices/virtual/input/input12 Bjorn Andersson (1): arm64: dts: qcom: sc8280xp: Define uart2 Steev Klimaszewski (3): dt-bindings: net: Add WCN6855 Bluetooth Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6855 arm64: dts: qcom: thinkpad-x13s: Add bluetooth .../net/bluetooth/qualcomm-bluetooth.yaml | 2 + .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 68 +++++++++++++++++++ arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 14 ++++ drivers/bluetooth/btqca.c | 24 ++++++- drivers/bluetooth/btqca.h | 10 +++ drivers/bluetooth/hci_qca.c | 59 ++++++++++++---- 6 files changed, 162 insertions(+), 15 deletions(-)