| Message ID | 20200914092744.17464-1-rjliao@codeaurora.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v2] Bluetooth: btusb: Add Qualcomm Bluetooth SoC WCN6855 support | expand |
Hi Rocky, > This patch add support for WCN6855 i.e. patch and nvm download > support. > > Signed-off-by: Rocky Liao <rjliao@codeaurora.org> > --- > drivers/bluetooth/btusb.c | 50 ++++++++++++++++++++++++++++++++++----- > 1 file changed, 44 insertions(+), 6 deletions(-) > > diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c > index fe80588c7bd3..789e8d5e829e 100644 > --- a/drivers/bluetooth/btusb.c > +++ b/drivers/bluetooth/btusb.c > @@ -59,6 +59,7 @@ static struct usb_driver btusb_driver; > #define BTUSB_MEDIATEK 0x200000 > #define BTUSB_WIDEBAND_SPEECH 0x400000 > #define BTUSB_VALID_LE_STATES 0x800000 > +#define BTUSB_QCA_WCN6855 0x1000000 > > static const struct usb_device_id btusb_table[] = { > /* Generic Bluetooth USB device */ > @@ -273,6 +274,10 @@ static const struct usb_device_id blacklist_table[] = { > { USB_DEVICE(0x13d3, 0x3496), .driver_info = BTUSB_QCA_ROME }, > { USB_DEVICE(0x13d3, 0x3501), .driver_info = BTUSB_QCA_ROME }, > > + /* QCA WCN6855 chipset */ > + { USB_DEVICE(0x0cf3, 0xe600), .driver_info = BTUSB_QCA_WCN6855 | > + BTUSB_WIDEBAND_SPEECH }, > + > /* Broadcom BCM2035 */ > { USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 }, > { USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU }, > @@ -3391,6 +3396,26 @@ static int btusb_set_bdaddr_ath3012(struct hci_dev *hdev, > return 0; > } > > +static int btusb_set_bdaddr_wcn6855(struct hci_dev *hdev, > + const bdaddr_t *bdaddr) > +{ > + struct sk_buff *skb; > + u8 buf[6]; > + long ret; > + > + memcpy(buf, bdaddr, sizeof(bdaddr_t)); > + > + skb = __hci_cmd_sync(hdev, 0xfc14, sizeof(buf), buf, HCI_INIT_TIMEOUT); > + if (IS_ERR(skb)) { > + ret = PTR_ERR(skb); > + bt_dev_err(hdev, "Change address command failed (%ld)", ret); > + return ret; > + } > + kfree_skb(skb); > + > + return 0; > +} > + > #define QCA_DFU_PACKET_LEN 4096 > > #define QCA_GET_TARGET_VERSION 0x09 > @@ -3428,6 +3453,8 @@ static const struct qca_device_info qca_devices_table[] = { > { 0x00000201, 28, 4, 18 }, /* Rome 2.1 */ > { 0x00000300, 28, 4, 18 }, /* Rome 3.0 */ > { 0x00000302, 28, 4, 18 }, /* Rome 3.2 */ > + { 0x00130100, 40, 4, 18 }, /* WCN6855 1.0 */ > + { 0x00130200, 40, 4, 18 } /* WCN6855 2.0 */ > }; > > static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request, > @@ -3529,8 +3556,8 @@ static int btusb_setup_qca_load_rampatch(struct hci_dev *hdev, > { > struct qca_rampatch_version *rver; > const struct firmware *fw; > - u32 ver_rom, ver_patch; > - u16 rver_rom, rver_patch; > + u32 ver_rom, ver_patch, rver_rom; > + u16 rver_rom_low, rver_rom_high, rver_patch; > char fwname[64]; > int err; > > @@ -3549,9 +3576,16 @@ static int btusb_setup_qca_load_rampatch(struct hci_dev *hdev, > bt_dev_info(hdev, "using rampatch file: %s", fwname); > > rver = (struct qca_rampatch_version *)(fw->data + info->ver_offset); > - rver_rom = le16_to_cpu(rver->rom_version); > + rver_rom_low = le16_to_cpu(rver->rom_version); > rver_patch = le16_to_cpu(rver->patch_version); > > + if (ver_rom & ~0xffffU) { > + rver_rom_high = le16_to_cpu(*(__le16 *)(fw->data + 16)); > + rver_rom = le32_to_cpu(rver_rom_high << 16 | rver_rom_low); > + } else { > + rver_rom = (__force u32)rver_rom_low; > + } > + I don’t get this. Is anything wrong with get_unaligned_le32 etc.? My brain just hurts with your casting and pointer magic. Maybe the whole rver logic needs a clean up first. Regards Marcel
Hi Marcel, 在 2020-09-14 21:28，Marcel Holtmann 写道： > Hi Rocky, > >> This patch add support for WCN6855 i.e. patch and nvm download >> support. >> >> Signed-off-by: Rocky Liao <rjliao@codeaurora.org> >> --- >> drivers/bluetooth/btusb.c | 50 ++++++++++++++++++++++++++++++++++----- >> 1 file changed, 44 insertions(+), 6 deletions(-) >> >> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c >> index fe80588c7bd3..789e8d5e829e 100644 >> --- a/drivers/bluetooth/btusb.c >> +++ b/drivers/bluetooth/btusb.c >> @@ -59,6 +59,7 @@ static struct usb_driver btusb_driver; >> #define BTUSB_MEDIATEK 0x200000 >> #define BTUSB_WIDEBAND_SPEECH 0x400000 >> #define BTUSB_VALID_LE_STATES 0x800000 >> +#define BTUSB_QCA_WCN6855 0x1000000 >> >> static const struct usb_device_id btusb_table[] = { >> /* Generic Bluetooth USB device */ >> @@ -273,6 +274,10 @@ static const struct usb_device_id >> blacklist_table[] = { >> { USB_DEVICE(0x13d3, 0x3496), .driver_info = BTUSB_QCA_ROME }, >> { USB_DEVICE(0x13d3, 0x3501), .driver_info = BTUSB_QCA_ROME }, >> >> + /* QCA WCN6855 chipset */ >> + { USB_DEVICE(0x0cf3, 0xe600), .driver_info = BTUSB_QCA_WCN6855 | >> + BTUSB_WIDEBAND_SPEECH }, >> + >> /* Broadcom BCM2035 */ >> { USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 }, >> { USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU }, >> @@ -3391,6 +3396,26 @@ static int btusb_set_bdaddr_ath3012(struct >> hci_dev *hdev, >> return 0; >> } >> >> +static int btusb_set_bdaddr_wcn6855(struct hci_dev *hdev, >> + const bdaddr_t *bdaddr) >> +{ >> + struct sk_buff *skb; >> + u8 buf[6]; >> + long ret; >> + >> + memcpy(buf, bdaddr, sizeof(bdaddr_t)); >> + >> + skb = __hci_cmd_sync(hdev, 0xfc14, sizeof(buf), buf, >> HCI_INIT_TIMEOUT); >> + if (IS_ERR(skb)) { >> + ret = PTR_ERR(skb); >> + bt_dev_err(hdev, "Change address command failed (%ld)", ret); >> + return ret; >> + } >> + kfree_skb(skb); >> + >> + return 0; >> +} >> + >> #define QCA_DFU_PACKET_LEN 4096 >> >> #define QCA_GET_TARGET_VERSION 0x09 >> @@ -3428,6 +3453,8 @@ static const struct qca_device_info >> qca_devices_table[] = { >> { 0x00000201, 28, 4, 18 }, /* Rome 2.1 */ >> { 0x00000300, 28, 4, 18 }, /* Rome 3.0 */ >> { 0x00000302, 28, 4, 18 }, /* Rome 3.2 */ >> + { 0x00130100, 40, 4, 18 }, /* WCN6855 1.0 */ >> + { 0x00130200, 40, 4, 18 } /* WCN6855 2.0 */ >> }; >> >> static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 >> request, >> @@ -3529,8 +3556,8 @@ static int btusb_setup_qca_load_rampatch(struct >> hci_dev *hdev, >> { >> struct qca_rampatch_version *rver; >> const struct firmware *fw; >> - u32 ver_rom, ver_patch; >> - u16 rver_rom, rver_patch; >> + u32 ver_rom, ver_patch, rver_rom; >> + u16 rver_rom_low, rver_rom_high, rver_patch; >> char fwname[64]; >> int err; >> >> @@ -3549,9 +3576,16 @@ static int btusb_setup_qca_load_rampatch(struct >> hci_dev *hdev, >> bt_dev_info(hdev, "using rampatch file: %s", fwname); >> >> rver = (struct qca_rampatch_version *)(fw->data + info->ver_offset); >> - rver_rom = le16_to_cpu(rver->rom_version); >> + rver_rom_low = le16_to_cpu(rver->rom_version); >> rver_patch = le16_to_cpu(rver->patch_version); >> >> + if (ver_rom & ~0xffffU) { >> + rver_rom_high = le16_to_cpu(*(__le16 *)(fw->data + 16)); >> + rver_rom = le32_to_cpu(rver_rom_high << 16 | rver_rom_low); >> + } else { >> + rver_rom = (__force u32)rver_rom_low; >> + } >> + > > I don’t get this. Is anything wrong with get_unaligned_le32 etc.? > > My brain just hurts with your casting and pointer magic. Maybe the > whole rver logic needs a clean up first. > It's not a 4 bytes le data, for example the version stream is 0x13, 0x00, 0x00, 0x01 and we need to convert it to 0x00130100. So we have to convert it to 2 u16 value then combine them to a u32. > Regards > > Marcel
Hi Rocky, >>> This patch add support for WCN6855 i.e. patch and nvm download >>> support. >>> Signed-off-by: Rocky Liao <rjliao@codeaurora.org> >>> --- >>> drivers/bluetooth/btusb.c | 50 ++++++++++++++++++++++++++++++++++----- >>> 1 file changed, 44 insertions(+), 6 deletions(-) >>> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c >>> index fe80588c7bd3..789e8d5e829e 100644 >>> --- a/drivers/bluetooth/btusb.c >>> +++ b/drivers/bluetooth/btusb.c >>> @@ -59,6 +59,7 @@ static struct usb_driver btusb_driver; >>> #define BTUSB_MEDIATEK 0x200000 >>> #define BTUSB_WIDEBAND_SPEECH 0x400000 >>> #define BTUSB_VALID_LE_STATES 0x800000 >>> +#define BTUSB_QCA_WCN6855 0x1000000 >>> static const struct usb_device_id btusb_table[] = { >>> /* Generic Bluetooth USB device */ >>> @@ -273,6 +274,10 @@ static const struct usb_device_id blacklist_table[] = { >>> { USB_DEVICE(0x13d3, 0x3496), .driver_info = BTUSB_QCA_ROME }, >>> { USB_DEVICE(0x13d3, 0x3501), .driver_info = BTUSB_QCA_ROME }, >>> + /* QCA WCN6855 chipset */ >>> + { USB_DEVICE(0x0cf3, 0xe600), .driver_info = BTUSB_QCA_WCN6855 | >>> + BTUSB_WIDEBAND_SPEECH }, >>> + >>> /* Broadcom BCM2035 */ >>> { USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 }, >>> { USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU }, >>> @@ -3391,6 +3396,26 @@ static int btusb_set_bdaddr_ath3012(struct hci_dev *hdev, >>> return 0; >>> } >>> +static int btusb_set_bdaddr_wcn6855(struct hci_dev *hdev, >>> + const bdaddr_t *bdaddr) >>> +{ >>> + struct sk_buff *skb; >>> + u8 buf[6]; >>> + long ret; >>> + >>> + memcpy(buf, bdaddr, sizeof(bdaddr_t)); >>> + >>> + skb = __hci_cmd_sync(hdev, 0xfc14, sizeof(buf), buf, HCI_INIT_TIMEOUT); >>> + if (IS_ERR(skb)) { >>> + ret = PTR_ERR(skb); >>> + bt_dev_err(hdev, "Change address command failed (%ld)", ret); >>> + return ret; >>> + } >>> + kfree_skb(skb); >>> + >>> + return 0; >>> +} >>> + >>> #define QCA_DFU_PACKET_LEN 4096 >>> #define QCA_GET_TARGET_VERSION 0x09 >>> @@ -3428,6 +3453,8 @@ static const struct qca_device_info qca_devices_table[] = { >>> { 0x00000201, 28, 4, 18 }, /* Rome 2.1 */ >>> { 0x00000300, 28, 4, 18 }, /* Rome 3.0 */ >>> { 0x00000302, 28, 4, 18 }, /* Rome 3.2 */ >>> + { 0x00130100, 40, 4, 18 }, /* WCN6855 1.0 */ >>> + { 0x00130200, 40, 4, 18 } /* WCN6855 2.0 */ >>> }; >>> static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request, >>> @@ -3529,8 +3556,8 @@ static int btusb_setup_qca_load_rampatch(struct hci_dev *hdev, >>> { >>> struct qca_rampatch_version *rver; >>> const struct firmware *fw; >>> - u32 ver_rom, ver_patch; >>> - u16 rver_rom, rver_patch; >>> + u32 ver_rom, ver_patch, rver_rom; >>> + u16 rver_rom_low, rver_rom_high, rver_patch; >>> char fwname[64]; >>> int err; >>> @@ -3549,9 +3576,16 @@ static int btusb_setup_qca_load_rampatch(struct hci_dev *hdev, >>> bt_dev_info(hdev, "using rampatch file: %s", fwname); >>> rver = (struct qca_rampatch_version *)(fw->data + info->ver_offset); >>> - rver_rom = le16_to_cpu(rver->rom_version); >>> + rver_rom_low = le16_to_cpu(rver->rom_version); >>> rver_patch = le16_to_cpu(rver->patch_version); >>> + if (ver_rom & ~0xffffU) { >>> + rver_rom_high = le16_to_cpu(*(__le16 *)(fw->data + 16)); >>> + rver_rom = le32_to_cpu(rver_rom_high << 16 | rver_rom_low); >>> + } else { >>> + rver_rom = (__force u32)rver_rom_low; >>> + } >>> + >> I don’t get this. Is anything wrong with get_unaligned_le32 etc.? >> My brain just hurts with your casting and pointer magic. Maybe the >> whole rver logic needs a clean up first. > It's not a 4 bytes le data, for example the version stream is 0x13, 0x00, 0x00, 0x01 and we need to convert it to 0x00130100. So we have to convert it to 2 u16 value then combine them to a u32. what is it then? Is it big endian formatted. If it is not a 32-bit value, then don’t store it as one. Regards Marcel
Hi Marcel, 在 2020-09-15 21:57，Marcel Holtmann 写道： > Hi Rocky, > >>>> This patch add support for WCN6855 i.e. patch and nvm download >>>> support. >>>> Signed-off-by: Rocky Liao <rjliao@codeaurora.org> >>>> --- >>>> drivers/bluetooth/btusb.c | 50 >>>> ++++++++++++++++++++++++++++++++++----- >>>> 1 file changed, 44 insertions(+), 6 deletions(-) >>>> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c >>>> index fe80588c7bd3..789e8d5e829e 100644 >>>> --- a/drivers/bluetooth/btusb.c >>>> +++ b/drivers/bluetooth/btusb.c >>>> @@ -59,6 +59,7 @@ static struct usb_driver btusb_driver; >>>> #define BTUSB_MEDIATEK 0x200000 >>>> #define BTUSB_WIDEBAND_SPEECH 0x400000 >>>> #define BTUSB_VALID_LE_STATES 0x800000 >>>> +#define BTUSB_QCA_WCN6855 0x1000000 >>>> static const struct usb_device_id btusb_table[] = { >>>> /* Generic Bluetooth USB device */ >>>> @@ -273,6 +274,10 @@ static const struct usb_device_id >>>> blacklist_table[] = { >>>> { USB_DEVICE(0x13d3, 0x3496), .driver_info = BTUSB_QCA_ROME }, >>>> { USB_DEVICE(0x13d3, 0x3501), .driver_info = BTUSB_QCA_ROME }, >>>> + /* QCA WCN6855 chipset */ >>>> + { USB_DEVICE(0x0cf3, 0xe600), .driver_info = BTUSB_QCA_WCN6855 | >>>> + BTUSB_WIDEBAND_SPEECH }, >>>> + >>>> /* Broadcom BCM2035 */ >>>> { USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 }, >>>> { USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU }, >>>> @@ -3391,6 +3396,26 @@ static int btusb_set_bdaddr_ath3012(struct >>>> hci_dev *hdev, >>>> return 0; >>>> } >>>> +static int btusb_set_bdaddr_wcn6855(struct hci_dev *hdev, >>>> + const bdaddr_t *bdaddr) >>>> +{ >>>> + struct sk_buff *skb; >>>> + u8 buf[6]; >>>> + long ret; >>>> + >>>> + memcpy(buf, bdaddr, sizeof(bdaddr_t)); >>>> + >>>> + skb = __hci_cmd_sync(hdev, 0xfc14, sizeof(buf), buf, >>>> HCI_INIT_TIMEOUT); >>>> + if (IS_ERR(skb)) { >>>> + ret = PTR_ERR(skb); >>>> + bt_dev_err(hdev, "Change address command failed (%ld)", ret); >>>> + return ret; >>>> + } >>>> + kfree_skb(skb); >>>> + >>>> + return 0; >>>> +} >>>> + >>>> #define QCA_DFU_PACKET_LEN 4096 >>>> #define QCA_GET_TARGET_VERSION 0x09 >>>> @@ -3428,6 +3453,8 @@ static const struct qca_device_info >>>> qca_devices_table[] = { >>>> { 0x00000201, 28, 4, 18 }, /* Rome 2.1 */ >>>> { 0x00000300, 28, 4, 18 }, /* Rome 3.0 */ >>>> { 0x00000302, 28, 4, 18 }, /* Rome 3.2 */ >>>> + { 0x00130100, 40, 4, 18 }, /* WCN6855 1.0 */ >>>> + { 0x00130200, 40, 4, 18 } /* WCN6855 2.0 */ >>>> }; >>>> static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 >>>> request, >>>> @@ -3529,8 +3556,8 @@ static int >>>> btusb_setup_qca_load_rampatch(struct hci_dev *hdev, >>>> { >>>> struct qca_rampatch_version *rver; >>>> const struct firmware *fw; >>>> - u32 ver_rom, ver_patch; >>>> - u16 rver_rom, rver_patch; >>>> + u32 ver_rom, ver_patch, rver_rom; >>>> + u16 rver_rom_low, rver_rom_high, rver_patch; >>>> char fwname[64]; >>>> int err; >>>> @@ -3549,9 +3576,16 @@ static int >>>> btusb_setup_qca_load_rampatch(struct hci_dev *hdev, >>>> bt_dev_info(hdev, "using rampatch file: %s", fwname); >>>> rver = (struct qca_rampatch_version *)(fw->data + >>>> info->ver_offset); >>>> - rver_rom = le16_to_cpu(rver->rom_version); >>>> + rver_rom_low = le16_to_cpu(rver->rom_version); >>>> rver_patch = le16_to_cpu(rver->patch_version); >>>> + if (ver_rom & ~0xffffU) { >>>> + rver_rom_high = le16_to_cpu(*(__le16 *)(fw->data + 16)); >>>> + rver_rom = le32_to_cpu(rver_rom_high << 16 | rver_rom_low); >>>> + } else { >>>> + rver_rom = (__force u32)rver_rom_low; >>>> + } >>>> + >>> I don’t get this. Is anything wrong with get_unaligned_le32 etc.? >>> My brain just hurts with your casting and pointer magic. Maybe the >>> whole rver logic needs a clean up first. >> It's not a 4 bytes le data, for example the version stream is 0x13, >> 0x00, 0x00, 0x01 and we need to convert it to 0x00130100. So we have >> to convert it to 2 u16 value then combine them to a u32. > > what is it then? Is it big endian formatted. If it is not a 32-bit > value, then don’t store it as one. > OK, let me refine the patch to a more readable format. > Regards > > Marcel
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index fe80588c7bd3..789e8d5e829e 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -59,6 +59,7 @@ static struct usb_driver btusb_driver; #define BTUSB_MEDIATEK 0x200000 #define BTUSB_WIDEBAND_SPEECH 0x400000 #define BTUSB_VALID_LE_STATES 0x800000 +#define BTUSB_QCA_WCN6855 0x1000000 static const struct usb_device_id btusb_table[] = { /* Generic Bluetooth USB device */ @@ -273,6 +274,10 @@ static const struct usb_device_id blacklist_table[] = { { USB_DEVICE(0x13d3, 0x3496), .driver_info = BTUSB_QCA_ROME }, { USB_DEVICE(0x13d3, 0x3501), .driver_info = BTUSB_QCA_ROME }, + /* QCA WCN6855 chipset */ + { USB_DEVICE(0x0cf3, 0xe600), .driver_info = BTUSB_QCA_WCN6855 | + BTUSB_WIDEBAND_SPEECH }, + /* Broadcom BCM2035 */ { USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 }, { USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU }, @@ -3391,6 +3396,26 @@ static int btusb_set_bdaddr_ath3012(struct hci_dev *hdev, return 0; } +static int btusb_set_bdaddr_wcn6855(struct hci_dev *hdev, + const bdaddr_t *bdaddr) +{ + struct sk_buff *skb; + u8 buf[6]; + long ret; + + memcpy(buf, bdaddr, sizeof(bdaddr_t)); + + skb = __hci_cmd_sync(hdev, 0xfc14, sizeof(buf), buf, HCI_INIT_TIMEOUT); + if (IS_ERR(skb)) { + ret = PTR_ERR(skb); + bt_dev_err(hdev, "Change address command failed (%ld)", ret); + return ret; + } + kfree_skb(skb); + + return 0; +} + #define QCA_DFU_PACKET_LEN 4096 #define QCA_GET_TARGET_VERSION 0x09 @@ -3428,6 +3453,8 @@ static const struct qca_device_info qca_devices_table[] = { { 0x00000201, 28, 4, 18 }, /* Rome 2.1 */ { 0x00000300, 28, 4, 18 }, /* Rome 3.0 */ { 0x00000302, 28, 4, 18 }, /* Rome 3.2 */ + { 0x00130100, 40, 4, 18 }, /* WCN6855 1.0 */ + { 0x00130200, 40, 4, 18 } /* WCN6855 2.0 */ }; static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request, @@ -3529,8 +3556,8 @@ static int btusb_setup_qca_load_rampatch(struct hci_dev *hdev, { struct qca_rampatch_version *rver; const struct firmware *fw; - u32 ver_rom, ver_patch; - u16 rver_rom, rver_patch; + u32 ver_rom, ver_patch, rver_rom; + u16 rver_rom_low, rver_rom_high, rver_patch; char fwname[64]; int err; @@ -3549,9 +3576,16 @@ static int btusb_setup_qca_load_rampatch(struct hci_dev *hdev, bt_dev_info(hdev, "using rampatch file: %s", fwname); rver = (struct qca_rampatch_version *)(fw->data + info->ver_offset); - rver_rom = le16_to_cpu(rver->rom_version); + rver_rom_low = le16_to_cpu(rver->rom_version); rver_patch = le16_to_cpu(rver->patch_version); + if (ver_rom & ~0xffffU) { + rver_rom_high = le16_to_cpu(*(__le16 *)(fw->data + 16)); + rver_rom = le32_to_cpu(rver_rom_high << 16 | rver_rom_low); + } else { + rver_rom = (__force u32)rver_rom_low; + } + bt_dev_info(hdev, "QCA: patch rome 0x%x build 0x%x, " "firmware rome 0x%x build 0x%x", rver_rom, rver_patch, ver_rom, ver_patch); @@ -3625,9 +3659,6 @@ static int btusb_setup_qca(struct hci_dev *hdev) return err; ver_rom = le32_to_cpu(ver.rom_version); - /* Don't care about high ROM versions */ - if (ver_rom & ~0xffffU) - return 0; for (i = 0; i < ARRAY_SIZE(qca_devices_table); i++) { if (ver_rom == qca_devices_table[i].rom_version) @@ -4063,6 +4094,13 @@ static int btusb_probe(struct usb_interface *intf, btusb_check_needs_reset_resume(intf); } + if (id->driver_info & BTUSB_QCA_WCN6855) { + data->setup_on_usb = btusb_setup_qca; + hdev->set_bdaddr = btusb_set_bdaddr_wcn6855; + hdev->cmd_timeout = btusb_qca_cmd_timeout; + set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks); + } + if (id->driver_info & BTUSB_AMP) { /* AMP controllers do not support SCO packets */ data->isoc = NULL;
This patch add support for WCN6855 i.e. patch and nvm download support. Signed-off-by: Rocky Liao <rjliao@codeaurora.org> --- drivers/bluetooth/btusb.c | 50 ++++++++++++++++++++++++++++++++++----- 1 file changed, 44 insertions(+), 6 deletions(-)