Message ID | 20201103120943.1289277-1-linus.walleij@linaro.org (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
Series | [1/2] Bluetooth: btbcm: Rewrite bindings i YAML and add reset | expand |
On Tue, 03 Nov 2020 13:09:42 +0100, Linus Walleij wrote: > This rewrites the Broadcom bluetooth bindings in YAML and > adds a GPIO handle for the BT_RST_N line as used on some > platforms. > > Cc: devicetree@vger.kernel.org > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> > --- > .../bindings/net/broadcom-bluetooth.txt | 56 --------- > .../bindings/net/broadcom-bluetooth.yaml | 117 ++++++++++++++++++ > 2 files changed, 117 insertions(+), 56 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.txt > create mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml > My bot found errors running 'make dt_binding_check' on your patch: yamllint warnings/errors: dtschema/dtc warnings/errors: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/serial/ingenic,uart.example.dt.yaml: bluetooth: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+' From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml See https://patchwork.ozlabs.org/patch/1392981 The base for the patch is generally the last rc1. Any dependencies should be noted. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit.
On Tue, Nov 03, 2020 at 01:09:42PM +0100, Linus Walleij wrote: > This rewrites the Broadcom bluetooth bindings in YAML and > adds a GPIO handle for the BT_RST_N line as used on some > platforms. Typo in subject. > > Cc: devicetree@vger.kernel.org > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> > --- > .../bindings/net/broadcom-bluetooth.txt | 56 --------- > .../bindings/net/broadcom-bluetooth.yaml | 117 ++++++++++++++++++ > 2 files changed, 117 insertions(+), 56 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.txt > create mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml > > diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt > deleted file mode 100644 > index a7d57ba5f2ac..000000000000 > --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt > +++ /dev/null > @@ -1,56 +0,0 @@ > -Broadcom Bluetooth Chips > ---------------------- > - > -This documents the binding structure and common properties for serial > -attached Broadcom devices. > - > -Serial attached Broadcom devices shall be a child node of the host UART > -device the slave device is attached to. > - > -Required properties: > - > - - compatible: should contain one of the following: > - * "brcm,bcm20702a1" > - * "brcm,bcm4329-bt" > - * "brcm,bcm4330-bt" > - * "brcm,bcm43438-bt" > - * "brcm,bcm4345c5" > - * "brcm,bcm43540-bt" > - * "brcm,bcm4335a0" > - > -Optional properties: > - > - - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml > - - shutdown-gpios: GPIO specifier, used to enable the BT module > - - device-wakeup-gpios: GPIO specifier, used to wakeup the controller > - - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor. > - deprecated, replaced by interrupts and > - "host-wakeup" interrupt-names > - - clocks: 1 or 2 clocks as defined in clock-names below, in that order > - - clock-names: names for clock inputs, matching the clocks given > - - "extclk": deprecated, replaced by "txco" > - - "txco": external reference clock (not a standalone crystal) > - - "lpo": external low power 32.768 kHz clock > - - vbat-supply: phandle to regulator supply for VBAT > - - vddio-supply: phandle to regulator supply for VDDIO > - - brcm,bt-pcm-int-params: configure PCM parameters via a 5-byte array > - - sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S > - - pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps > - - pcm-frame-type: short, long > - - pcm-sync-mode: slave, master > - - pcm-clock-mode: slave, master > - - interrupts: must be one, used to wakeup the host processor > - - interrupt-names: must be "host-wakeup" > - > -Example: > - > -&uart2 { > - pinctrl-names = "default"; > - pinctrl-0 = <&uart2_pins>; > - > - bluetooth { > - compatible = "brcm,bcm43438-bt"; > - max-speed = <921600>; > - brcm,bt-pcm-int-params = [01 02 00 01 01]; > - }; > -}; > diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml > new file mode 100644 > index 000000000000..bdd6ca617e23 > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml > @@ -0,0 +1,117 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/net/broadcom-bluetooth.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Broadcom Bluetooth Chips > + > +maintainers: > + - Linus Walleij <linus.walleij@linaro.org> > + > +description: > + This binding describes Broadcom UART-attached bluetooth chips. > + > +properties: > + compatible: > + enum: > + - brcm,bcm20702a1 > + - brcm,bcm4329-bt > + - brcm,bcm4330-bt > + - brcm,bcm43438-bt > + - brcm,bcm4345c5 > + - brcm,bcm43540-bt > + - brcm,bcm4335a0 > + > + shutdown-gpios: > + maxItems: 1 > + description: GPIO specifier for the line BT_REG_ON used to > + power on the BT module > + > + reset-gpios: > + maxItems: 1 > + description: GPIO specifier for the line BT_RST_N used to > + reset the BT module. This should be marked as > + GPIO_ACTIVE_LOW. > + > + device-wakeup-gpios: > + maxItems: 1 > + description: GPIO specifier for the line BT_WAKE used to > + wakeup the controller. This is using the BT_GPIO_0 > + pin on the chip when in use. > + > + host-wakeup-gpios: > + maxItems: 1 > + deprecated: true > + description: GPIO specifier for the line HOST_WAKE used > + to wakeup the host processor. This is using he BT_GPIO_1 > + pin on the chip when in use. This is deprecated and replaced > + by interrupts and "host-wakeup" interrupt-names > + > + clocks: > + maxItems: 2 > + description: 1 or 2 clocks as defined in clock-names below, > + in that order > + > + clock-names: > + description: Names of the 1 to 2 supplied clocks > + items: > + - const: txco > + - const: lpo > + - const: extclk > + > + vbat-supply: > + description: phandle to regulator supply for VBAT > + > + vddio-supply: > + description: phandle to regulator supply for VDDIO > + > + brcm,bt-pcm-int-params: > + $ref: /schemas/types.yaml#/definitions/uint8-array > + minItems: 5 > + maxItems: 5 > + description: |- > + configure PCM parameters via a 5-byte array: > + sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S > + pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps > + pcm-frame-type: short, long > + pcm-sync-mode: slave, master > + pcm-clock-mode: slave, master > + > + interrupts: > + items: > + - description: Handle to the line HOST_WAKE used to wake > + up the host processor. This uses the BT_GPIO_1 pin on > + the chip when in use. > + > + interrupt-names: > + items: > + - const: host-wakeup > + > + max-speed: true > + current-speed: true > + > +required: > + - compatible > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + #include <dt-bindings/interrupt-controller/irq.h> > + > + uart { > + uart-has-rtscts; > + > + bluetooth { > + compatible = "brcm,bcm4330-bt"; > + max-speed = <921600>; > + brcm,bt-pcm-int-params = [01 02 00 01 01]; > + shutdown-gpios = <&gpio 30 GPIO_ACTIVE_HIGH>; > + device-wakeup-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; > + reset-gpios = <&gpio 9 GPIO_ACTIVE_LOW>; > + interrupt-parent = <&gpio>; > + interrupts = <8 IRQ_TYPE_EDGE_FALLING>; > + }; > + }; > -- > 2.26.2 >
diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt deleted file mode 100644 index a7d57ba5f2ac..000000000000 --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt +++ /dev/null @@ -1,56 +0,0 @@ -Broadcom Bluetooth Chips ---------------------- - -This documents the binding structure and common properties for serial -attached Broadcom devices. - -Serial attached Broadcom devices shall be a child node of the host UART -device the slave device is attached to. - -Required properties: - - - compatible: should contain one of the following: - * "brcm,bcm20702a1" - * "brcm,bcm4329-bt" - * "brcm,bcm4330-bt" - * "brcm,bcm43438-bt" - * "brcm,bcm4345c5" - * "brcm,bcm43540-bt" - * "brcm,bcm4335a0" - -Optional properties: - - - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml - - shutdown-gpios: GPIO specifier, used to enable the BT module - - device-wakeup-gpios: GPIO specifier, used to wakeup the controller - - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor. - deprecated, replaced by interrupts and - "host-wakeup" interrupt-names - - clocks: 1 or 2 clocks as defined in clock-names below, in that order - - clock-names: names for clock inputs, matching the clocks given - - "extclk": deprecated, replaced by "txco" - - "txco": external reference clock (not a standalone crystal) - - "lpo": external low power 32.768 kHz clock - - vbat-supply: phandle to regulator supply for VBAT - - vddio-supply: phandle to regulator supply for VDDIO - - brcm,bt-pcm-int-params: configure PCM parameters via a 5-byte array - - sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S - - pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps - - pcm-frame-type: short, long - - pcm-sync-mode: slave, master - - pcm-clock-mode: slave, master - - interrupts: must be one, used to wakeup the host processor - - interrupt-names: must be "host-wakeup" - -Example: - -&uart2 { - pinctrl-names = "default"; - pinctrl-0 = <&uart2_pins>; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - max-speed = <921600>; - brcm,bt-pcm-int-params = [01 02 00 01 01]; - }; -}; diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml new file mode 100644 index 000000000000..bdd6ca617e23 --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml @@ -0,0 +1,117 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/broadcom-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom Bluetooth Chips + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: + This binding describes Broadcom UART-attached bluetooth chips. + +properties: + compatible: + enum: + - brcm,bcm20702a1 + - brcm,bcm4329-bt + - brcm,bcm4330-bt + - brcm,bcm43438-bt + - brcm,bcm4345c5 + - brcm,bcm43540-bt + - brcm,bcm4335a0 + + shutdown-gpios: + maxItems: 1 + description: GPIO specifier for the line BT_REG_ON used to + power on the BT module + + reset-gpios: + maxItems: 1 + description: GPIO specifier for the line BT_RST_N used to + reset the BT module. This should be marked as + GPIO_ACTIVE_LOW. + + device-wakeup-gpios: + maxItems: 1 + description: GPIO specifier for the line BT_WAKE used to + wakeup the controller. This is using the BT_GPIO_0 + pin on the chip when in use. + + host-wakeup-gpios: + maxItems: 1 + deprecated: true + description: GPIO specifier for the line HOST_WAKE used + to wakeup the host processor. This is using he BT_GPIO_1 + pin on the chip when in use. This is deprecated and replaced + by interrupts and "host-wakeup" interrupt-names + + clocks: + maxItems: 2 + description: 1 or 2 clocks as defined in clock-names below, + in that order + + clock-names: + description: Names of the 1 to 2 supplied clocks + items: + - const: txco + - const: lpo + - const: extclk + + vbat-supply: + description: phandle to regulator supply for VBAT + + vddio-supply: + description: phandle to regulator supply for VDDIO + + brcm,bt-pcm-int-params: + $ref: /schemas/types.yaml#/definitions/uint8-array + minItems: 5 + maxItems: 5 + description: |- + configure PCM parameters via a 5-byte array: + sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S + pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps + pcm-frame-type: short, long + pcm-sync-mode: slave, master + pcm-clock-mode: slave, master + + interrupts: + items: + - description: Handle to the line HOST_WAKE used to wake + up the host processor. This uses the BT_GPIO_1 pin on + the chip when in use. + + interrupt-names: + items: + - const: host-wakeup + + max-speed: true + current-speed: true + +required: + - compatible + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + uart { + uart-has-rtscts; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + max-speed = <921600>; + brcm,bt-pcm-int-params = [01 02 00 01 01]; + shutdown-gpios = <&gpio 30 GPIO_ACTIVE_HIGH>; + device-wakeup-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio>; + interrupts = <8 IRQ_TYPE_EDGE_FALLING>; + }; + };
This rewrites the Broadcom bluetooth bindings in YAML and adds a GPIO handle for the BT_RST_N line as used on some platforms. Cc: devicetree@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- .../bindings/net/broadcom-bluetooth.txt | 56 --------- .../bindings/net/broadcom-bluetooth.yaml | 117 ++++++++++++++++++ 2 files changed, 117 insertions(+), 56 deletions(-) delete mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.txt create mode 100644 Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml