diff mbox series

[v2,3/4] arm64: dts: qcom: sc8280xp: Define uart2

Message ID 20230131043816.4525-4-steev@kali.org (mailing list archive)
State Superseded
Headers show
Series Attempt at adding WCN6855 BT support | expand

Checks

Context Check Description
tedd_an/pre-ci_am fail error: patch failed: arch/arm64/boot/dts/qcom/sc8280xp.dtsi:1207 error: arch/arm64/boot/dts/qcom/sc8280xp.dtsi: patch does not apply hint: Use 'git am --show-current-patch' to see the failed patch

Commit Message

Steev Klimaszewski Jan. 31, 2023, 4:38 a.m. UTC 
From: Bjorn Andersson <bjorn.andersson@linaro.org>


Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Steev Klimaszewski <steev@kali.org>
---
Changes since v1:
* Changed subject line
* Move node to the correct place based on address
* Add my Signed-off-by
---
 arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

Comments

Brian Masney Jan. 31, 2023, 11:15 a.m. UTC | #1 
On Mon, Jan 30, 2023 at 10:38:15PM -0600, Steev Klimaszewski wrote:
> From: Bjorn Andersson <bjorn.andersson@linaro.org>
> 
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Signed-off-by: Steev Klimaszewski <steev@kali.org>

Reviewed-by: Brian Masney <bmasney@redhat.com>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
index fa2d0d7d1367..eab54aab3b76 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
@@ -1207,6 +1207,20 @@  spi2: spi@988000 {
 				status = "disabled";
 			};
 
+			uart2: serial@988000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00988000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				clock-names = "se";
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				power-domains = <&rpmhpd SC8280XP_CX>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
 			i2c3: i2c@98c000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0 0x0098c000 0 0x4000>;