| Message ID | 1435572900-56998-15-git-send-email-hans.verkuil@cisco.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Marek, Kamil, On 06/29/15 12:14, Hans Verkuil wrote: > From: Kamil Debski <kamil@wypas.org> > > Add CEC interface driver present in the Samsung Exynos range of > SoCs. > > The following files were based on work by SangPil Moon: > - exynos_hdmi_cec.h > - exynos_hdmi_cecctl.c > > Signed-off-by: Kamil Debski <kamil@wypas.org> > Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> > --- <snip> > diff --git a/drivers/media/platform/s5p-cec/s5p_cec.c b/drivers/media/platform/s5p-cec/s5p_cec.c > new file mode 100644 > index 0000000..0f16d00 > --- /dev/null > +++ b/drivers/media/platform/s5p-cec/s5p_cec.c > @@ -0,0 +1,283 @@ > +/* drivers/media/platform/s5p-cec/s5p_cec.c > + * > + * Samsung S5P CEC driver > + * > + * Copyright (c) 2014 Samsung Electronics Co., Ltd. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This driver is based on the "cec interface driver for exynos soc" by > + * SangPil Moon. > + */ > + > +#include <linux/clk.h> > +#include <linux/interrupt.h> > +#include <linux/kernel.h> > +#include <linux/mfd/syscon.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/platform_device.h> > +#include <linux/pm_runtime.h> > +#include <linux/timer.h> > +#include <linux/version.h> > +#include <linux/workqueue.h> > +#include <media/cec.h> > + > +#include "exynos_hdmi_cec.h" > +#include "regs-cec.h" > +#include "s5p_cec.h" > + > +#define CEC_NAME "s5p-cec" > + > +static int debug; > +module_param(debug, int, 0644); > +MODULE_PARM_DESC(debug, "debug level (0-2)"); > + > +static int s5p_cec_enable(struct cec_adapter *adap, bool enable) > +{ > + struct s5p_cec_dev *cec = container_of(adap, struct s5p_cec_dev, adap); > + int ret; > + > + if (enable) { > + ret = pm_runtime_get_sync(cec->dev); > + > + adap->phys_addr = 0x100b; This is a bogus physical address. The actual physical address has to be derived from the EDID that is read by the HDMI transmitter. I think in the case of this driver it will have to be userspace that assigns the physical address after reading the EDID from drm/kms? How did you test this, Kamil? Regards, Hans > + s5p_cec_reset(cec); > + > + s5p_cec_set_divider(cec); > + s5p_cec_threshold(cec); > + > + s5p_cec_unmask_tx_interrupts(cec); > + s5p_cec_unmask_rx_interrupts(cec); > + s5p_cec_enable_rx(cec); > + } else { > + s5p_cec_mask_tx_interrupts(cec); > + s5p_cec_mask_rx_interrupts(cec); > + pm_runtime_disable(cec->dev); > + } > + > + return 0; > +} > + > +static int s5p_cec_log_addr(struct cec_adapter *adap, u8 addr) > +{ > + struct s5p_cec_dev *cec = container_of(adap, struct s5p_cec_dev, adap); > + > + s5p_cec_set_addr(cec, addr); > + return 0; > +} > + > +static int s5p_cec_transmit(struct cec_adapter *adap, struct cec_msg *msg) > +{ > + struct s5p_cec_dev *cec = container_of(adap, struct s5p_cec_dev, adap); > + > + s5p_cec_copy_packet(cec, msg->msg, msg->len); > + return 0; > +} > + > +static void s5p_cec_transmit_timed_out(struct cec_adapter *adap) > +{ > + > +} > + > +static irqreturn_t s5p_cec_irq_handler(int irq, void *priv) > +{ > + struct s5p_cec_dev *cec = priv; > + u32 status = 0; > + > + status = s5p_cec_get_status(cec); > + > + dev_dbg(cec->dev, "irq received\n"); > + > + if (status & CEC_STATUS_TX_DONE) { > + if (status & CEC_STATUS_TX_ERROR) { > + dev_dbg(cec->dev, "CEC_STATUS_TX_ERROR set\n"); > + cec->tx = STATE_ERROR; > + } else { > + dev_dbg(cec->dev, "CEC_STATUS_TX_DONE\n"); > + cec->tx = STATE_DONE; > + } > + s5p_clr_pending_tx(cec); > + } > + > + if (status & CEC_STATUS_RX_DONE) { > + if (status & CEC_STATUS_RX_ERROR) { > + dev_dbg(cec->dev, "CEC_STATUS_RX_ERROR set\n"); > + s5p_cec_rx_reset(cec); > + s5p_cec_enable_rx(cec); > + } else { > + dev_dbg(cec->dev, "CEC_STATUS_RX_DONE set\n"); > + if (cec->rx != STATE_IDLE) > + dev_dbg(cec->dev, "Buffer overrun (worker did not process previous message)\n"); > + cec->rx = STATE_BUSY; > + cec->msg.len = status >> 24; > + cec->msg.status = CEC_RX_STATUS_READY; > + s5p_cec_get_rx_buf(cec, cec->msg.len, > + cec->msg.msg); > + cec->rx = STATE_DONE; > + s5p_cec_enable_rx(cec); > + } > + /* Clear interrupt pending bit */ > + s5p_clr_pending_rx(cec); > + } > + return IRQ_WAKE_THREAD; > +} > + > +static irqreturn_t s5p_cec_irq_handler_thread(int irq, void *priv) > +{ > + struct s5p_cec_dev *cec = priv; > + > + dev_dbg(cec->dev, "irq processing thread\n"); > + switch (cec->tx) { > + case STATE_DONE: > + cec_transmit_done(&cec->adap, CEC_TX_STATUS_OK); > + cec->tx = STATE_IDLE; > + break; > + case STATE_ERROR: > + cec_transmit_done(&cec->adap, CEC_TX_STATUS_RETRY_TIMEOUT); > + cec->tx = STATE_IDLE; > + break; > + case STATE_BUSY: > + dev_err(cec->dev, "state set to busy, this should not occur here\n"); > + break; > + default: > + break; > + } > + > + switch (cec->rx) { > + case STATE_DONE: > + cec_received_msg(&cec->adap, &cec->msg); > + cec->rx = STATE_IDLE; > + default: > + break; > + }; > + > + return IRQ_HANDLED; > +} > + > +static int s5p_cec_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev; > + struct resource *res; > + struct s5p_cec_dev *cec; > + int ret; > + > + cec = devm_kzalloc(&pdev->dev, sizeof(*cec), GFP_KERNEL); > + if (!dev) > + return -ENOMEM; > + > + cec->dev = dev; > + > + cec->irq = platform_get_irq(pdev, 0); > + if (IS_ERR_VALUE(cec->irq)) > + return cec->irq; > + > + ret = devm_request_threaded_irq(dev, cec->irq, s5p_cec_irq_handler, > + s5p_cec_irq_handler_thread, 0, pdev->name, cec); > + if (IS_ERR_VALUE(ret)) > + return ret; > + > + cec->clk = devm_clk_get(dev, "hdmicec"); > + if (IS_ERR(cec->clk)) > + return PTR_ERR(cec->clk); > + > + cec->pmu = syscon_regmap_lookup_by_phandle(dev->of_node, > + "samsung,syscon-phandle"); > + if (IS_ERR(cec->pmu)) > + return -EPROBE_DEFER; > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + cec->reg = devm_ioremap_resource(dev, res); > + if (IS_ERR(cec->reg)) > + return PTR_ERR(cec->reg); > + > + cec->adap.available_log_addrs = 1; > + cec->adap.adap_enable = s5p_cec_enable; > + cec->adap.adap_log_addr = s5p_cec_log_addr; > + cec->adap.adap_transmit = s5p_cec_transmit; > + cec->adap.adap_transmit_timed_out = s5p_cec_transmit_timed_out; > + cec_create_adapter(&cec->adap, CEC_NAME, CEC_CAP_STATE | > + CEC_CAP_LOG_ADDRS | CEC_CAP_TRANSMIT | > + CEC_CAP_RECEIVE, true, THIS_MODULE, &pdev->dev); > + > + platform_set_drvdata(pdev, cec); > + pm_runtime_enable(dev); > + > + dev_dbg(dev, "successfuly probed\n"); > + return 0; > +} > + > +static int s5p_cec_remove(struct platform_device *pdev) > +{ > + struct s5p_cec_dev *cec = platform_get_drvdata(pdev); > + > + cec_delete_adapter(&cec->adap); > + pm_runtime_disable(&pdev->dev); > + return 0; > +} > + > +static int s5p_cec_runtime_suspend(struct device *dev) > +{ > + struct s5p_cec_dev *cec = dev_get_drvdata(dev); > + > + clk_disable_unprepare(cec->clk); > + return 0; > +} > + > +static int s5p_cec_runtime_resume(struct device *dev) > +{ > + struct s5p_cec_dev *cec = dev_get_drvdata(dev); > + int ret; > + > + ret = clk_prepare_enable(cec->clk); > + if (ret < 0) > + return ret; > + return 0; > +} > + > +static int s5p_cec_suspend(struct device *dev) > +{ > + if (pm_runtime_suspended(dev)) > + return 0; > + return s5p_cec_runtime_suspend(dev); > +} > + > +static int s5p_cec_resume(struct device *dev) > +{ > + if (pm_runtime_suspended(dev)) > + return 0; > + return s5p_cec_runtime_resume(dev); > +} > + > +static const struct dev_pm_ops s5p_cec_pm_ops = { > + SET_SYSTEM_SLEEP_PM_OPS(s5p_cec_suspend, s5p_cec_resume) > + SET_RUNTIME_PM_OPS(s5p_cec_runtime_suspend, s5p_cec_runtime_resume, > + NULL) > +}; > + > +static const struct of_device_id s5p_cec_match[] = { > + { > + .compatible = "samsung,s5p-cec", > + }, > + {}, > +}; > + > +static struct platform_driver s5p_cec_pdrv = { > + .probe = s5p_cec_probe, > + .remove = s5p_cec_remove, > + .driver = { > + .name = CEC_NAME, > + .owner = THIS_MODULE, > + .of_match_table = s5p_cec_match, > + .pm = &s5p_cec_pm_ops, > + }, > +}; > + > +module_platform_driver(s5p_cec_pdrv); > + > +MODULE_AUTHOR("Kamil Debski <kamil@wypas.org>"); > +MODULE_LICENSE("GPL"); > +MODULE_DESCRIPTION("Samsung S5P CEC driver"); > diff --git a/drivers/media/platform/s5p-cec/s5p_cec.h b/drivers/media/platform/s5p-cec/s5p_cec.h > new file mode 100644 > index 0000000..d6ffd92 > --- /dev/null > +++ b/drivers/media/platform/s5p-cec/s5p_cec.h > @@ -0,0 +1,76 @@ > +/* drivers/media/platform/s5p-cec/s5p_cec.h > + * > + * Samsung S5P HDMI CEC driver > + * > + * Copyright (c) 2014 Samsung Electronics Co., Ltd. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + */ > + > +#ifndef _S5P_CEC_H_ > +#define _S5P_CEC_H_ __FILE__ > + > +#include <linux/clk.h> > +#include <linux/interrupt.h> > +#include <linux/kernel.h> > +#include <linux/mfd/syscon.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/platform_device.h> > +#include <linux/pm_runtime.h> > +#include <linux/timer.h> > +#include <linux/version.h> > +#include <linux/workqueue.h> > +#include <media/cec.h> > + > +#include "exynos_hdmi_cec.h" > +#include "regs-cec.h" > +#include "s5p_cec.h" > + > +#define CEC_NAME "s5p-cec" > + > +#define CEC_STATUS_TX_RUNNING (1 << 0) > +#define CEC_STATUS_TX_TRANSFERRING (1 << 1) > +#define CEC_STATUS_TX_DONE (1 << 2) > +#define CEC_STATUS_TX_ERROR (1 << 3) > +#define CEC_STATUS_TX_BYTES (0xFF << 8) > +#define CEC_STATUS_RX_RUNNING (1 << 16) > +#define CEC_STATUS_RX_RECEIVING (1 << 17) > +#define CEC_STATUS_RX_DONE (1 << 18) > +#define CEC_STATUS_RX_ERROR (1 << 19) > +#define CEC_STATUS_RX_BCAST (1 << 20) > +#define CEC_STATUS_RX_BYTES (0xFF << 24) > + > +#define CEC_WORKER_TX_DONE (1 << 0) > +#define CEC_WORKER_RX_MSG (1 << 1) > + > +/* CEC Rx buffer size */ > +#define CEC_RX_BUFF_SIZE 16 > +/* CEC Tx buffer size */ > +#define CEC_TX_BUFF_SIZE 16 > + > +enum cec_state { > + STATE_IDLE, > + STATE_BUSY, > + STATE_DONE, > + STATE_ERROR > +}; > + > +struct s5p_cec_dev { > + struct cec_adapter adap; > + struct clk *clk; > + struct device *dev; > + struct mutex lock; > + struct regmap *pmu; > + int irq; > + void __iomem *reg; > + > + enum cec_state rx; > + enum cec_state tx; > + struct cec_msg msg; > +}; > + > +#endif /* _S5P_CEC_H_ */ >
Hello, On 2015-07-16 15:09, Hans Verkuil wrote: > Marek, Kamil, > > On 06/29/15 12:14, Hans Verkuil wrote: >> From: Kamil Debski <kamil@wypas.org> >> >> Add CEC interface driver present in the Samsung Exynos range of >> SoCs. >> >> The following files were based on work by SangPil Moon: >> - exynos_hdmi_cec.h >> - exynos_hdmi_cecctl.c >> >> Signed-off-by: Kamil Debski <kamil@wypas.org> >> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> >> --- > <snip> > >> diff --git a/drivers/media/platform/s5p-cec/s5p_cec.c b/drivers/media/platform/s5p-cec/s5p_cec.c >> new file mode 100644 >> index 0000000..0f16d00 >> --- /dev/null >> +++ b/drivers/media/platform/s5p-cec/s5p_cec.c >> @@ -0,0 +1,283 @@ >> +/* drivers/media/platform/s5p-cec/s5p_cec.c >> + * >> + * Samsung S5P CEC driver >> + * >> + * Copyright (c) 2014 Samsung Electronics Co., Ltd. >> + * >> + * This program is free software; you can redistribute it and/or modify >> + * it under the terms of the GNU General Public License as published by >> + * the Free Software Foundation; either version 2 of the License, or >> + * (at your option) any later version. >> + * >> + * This driver is based on the "cec interface driver for exynos soc" by >> + * SangPil Moon. >> + */ >> + >> +#include <linux/clk.h> >> +#include <linux/interrupt.h> >> +#include <linux/kernel.h> >> +#include <linux/mfd/syscon.h> >> +#include <linux/module.h> >> +#include <linux/of.h> >> +#include <linux/platform_device.h> >> +#include <linux/pm_runtime.h> >> +#include <linux/timer.h> >> +#include <linux/version.h> >> +#include <linux/workqueue.h> >> +#include <media/cec.h> >> + >> +#include "exynos_hdmi_cec.h" >> +#include "regs-cec.h" >> +#include "s5p_cec.h" >> + >> +#define CEC_NAME "s5p-cec" >> + >> +static int debug; >> +module_param(debug, int, 0644); >> +MODULE_PARM_DESC(debug, "debug level (0-2)"); >> + >> +static int s5p_cec_enable(struct cec_adapter *adap, bool enable) >> +{ >> + struct s5p_cec_dev *cec = container_of(adap, struct s5p_cec_dev, adap); >> + int ret; >> + >> + if (enable) { >> + ret = pm_runtime_get_sync(cec->dev); >> + >> + adap->phys_addr = 0x100b; > This is a bogus physical address. The actual physical address has to be derived > from the EDID that is read by the HDMI transmitter. > > I think in the case of this driver it will have to be userspace that assigns > the physical address after reading the EDID from drm/kms? > > How did you test this, Kamil? If I remember correctly, physical address has been derived from EDID in the userspace (it is available in /sys/class/drm/*) and passed to s5p-cec driver by appropriate ioctl. I don't know what is the reason for the above 'adap->phys_addr = 0x100b' assignment. Best regards
Hi, On 21 July 2015 at 15:03, Marek Szyprowski <m.szyprowski@samsung.com> wrote: > Hello, > > On 2015-07-16 15:09, Hans Verkuil wrote: >> >> Marek, Kamil, >> >> On 06/29/15 12:14, Hans Verkuil wrote: >>> >>> From: Kamil Debski <kamil@wypas.org> >>> >>> Add CEC interface driver present in the Samsung Exynos range of >>> SoCs. >>> >>> The following files were based on work by SangPil Moon: >>> - exynos_hdmi_cec.h >>> - exynos_hdmi_cecctl.c >>> >>> Signed-off-by: Kamil Debski <kamil@wypas.org> >>> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> >>> --- >> >> <snip> >> >>> diff --git a/drivers/media/platform/s5p-cec/s5p_cec.c >>> b/drivers/media/platform/s5p-cec/s5p_cec.c >>> new file mode 100644 >>> index 0000000..0f16d00 >>> --- /dev/null >>> +++ b/drivers/media/platform/s5p-cec/s5p_cec.c >>> @@ -0,0 +1,283 @@ >>> +/* drivers/media/platform/s5p-cec/s5p_cec.c >>> + * >>> + * Samsung S5P CEC driver >>> + * >>> + * Copyright (c) 2014 Samsung Electronics Co., Ltd. >>> + * >>> + * This program is free software; you can redistribute it and/or modify >>> + * it under the terms of the GNU General Public License as published by >>> + * the Free Software Foundation; either version 2 of the License, or >>> + * (at your option) any later version. >>> + * >>> + * This driver is based on the "cec interface driver for exynos soc" by >>> + * SangPil Moon. >>> + */ >>> + >>> +#include <linux/clk.h> >>> +#include <linux/interrupt.h> >>> +#include <linux/kernel.h> >>> +#include <linux/mfd/syscon.h> >>> +#include <linux/module.h> >>> +#include <linux/of.h> >>> +#include <linux/platform_device.h> >>> +#include <linux/pm_runtime.h> >>> +#include <linux/timer.h> >>> +#include <linux/version.h> >>> +#include <linux/workqueue.h> >>> +#include <media/cec.h> >>> + >>> +#include "exynos_hdmi_cec.h" >>> +#include "regs-cec.h" >>> +#include "s5p_cec.h" >>> + >>> +#define CEC_NAME "s5p-cec" >>> + >>> +static int debug; >>> +module_param(debug, int, 0644); >>> +MODULE_PARM_DESC(debug, "debug level (0-2)"); >>> + >>> +static int s5p_cec_enable(struct cec_adapter *adap, bool enable) >>> +{ >>> + struct s5p_cec_dev *cec = container_of(adap, struct s5p_cec_dev, >>> adap); >>> + int ret; >>> + >>> + if (enable) { >>> + ret = pm_runtime_get_sync(cec->dev); >>> + >>> + adap->phys_addr = 0x100b; >> >> This is a bogus physical address. The actual physical address has to be >> derived >> from the EDID that is read by the HDMI transmitter. >> >> I think in the case of this driver it will have to be userspace that >> assigns >> the physical address after reading the EDID from drm/kms? >> >> How did you test this, Kamil? > > > If I remember correctly, physical address has been derived from EDID in the > userspace (it is available in /sys/class/drm/*) and passed to s5p-cec driver > by > appropriate ioctl. > > I don't know what is the reason for the above 'adap->phys_addr = 0x100b' > assignment. At some point there was an idea to read the address from the EDID in kernel. This static address was a hack until the code that reads the EDID is written. As you say, it is much better to leave the address to be set by the userspace. So this assignment serves no purpose anymore. > > Best regards > -- > Marek Szyprowski, PhD > Samsung R&D Institute Poland > Best wishes, Kamil
On 07/23/2015 06:39 PM, Kamil Debski wrote: > Hi, > > On 21 July 2015 at 15:03, Marek Szyprowski <m.szyprowski@samsung.com> wrote: >> Hello, >> >> On 2015-07-16 15:09, Hans Verkuil wrote: >>> >>> Marek, Kamil, >>> >>> On 06/29/15 12:14, Hans Verkuil wrote: >>>> >>>> From: Kamil Debski <kamil@wypas.org> >>>> >>>> Add CEC interface driver present in the Samsung Exynos range of >>>> SoCs. >>>> >>>> The following files were based on work by SangPil Moon: >>>> - exynos_hdmi_cec.h >>>> - exynos_hdmi_cecctl.c >>>> >>>> Signed-off-by: Kamil Debski <kamil@wypas.org> >>>> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> >>>> --- >>> >>> <snip> >>> >>>> diff --git a/drivers/media/platform/s5p-cec/s5p_cec.c >>>> b/drivers/media/platform/s5p-cec/s5p_cec.c >>>> new file mode 100644 >>>> index 0000000..0f16d00 >>>> --- /dev/null >>>> +++ b/drivers/media/platform/s5p-cec/s5p_cec.c >>>> @@ -0,0 +1,283 @@ >>>> +/* drivers/media/platform/s5p-cec/s5p_cec.c >>>> + * >>>> + * Samsung S5P CEC driver >>>> + * >>>> + * Copyright (c) 2014 Samsung Electronics Co., Ltd. >>>> + * >>>> + * This program is free software; you can redistribute it and/or modify >>>> + * it under the terms of the GNU General Public License as published by >>>> + * the Free Software Foundation; either version 2 of the License, or >>>> + * (at your option) any later version. >>>> + * >>>> + * This driver is based on the "cec interface driver for exynos soc" by >>>> + * SangPil Moon. >>>> + */ >>>> + >>>> +#include <linux/clk.h> >>>> +#include <linux/interrupt.h> >>>> +#include <linux/kernel.h> >>>> +#include <linux/mfd/syscon.h> >>>> +#include <linux/module.h> >>>> +#include <linux/of.h> >>>> +#include <linux/platform_device.h> >>>> +#include <linux/pm_runtime.h> >>>> +#include <linux/timer.h> >>>> +#include <linux/version.h> >>>> +#include <linux/workqueue.h> >>>> +#include <media/cec.h> >>>> + >>>> +#include "exynos_hdmi_cec.h" >>>> +#include "regs-cec.h" >>>> +#include "s5p_cec.h" >>>> + >>>> +#define CEC_NAME "s5p-cec" >>>> + >>>> +static int debug; >>>> +module_param(debug, int, 0644); >>>> +MODULE_PARM_DESC(debug, "debug level (0-2)"); >>>> + >>>> +static int s5p_cec_enable(struct cec_adapter *adap, bool enable) >>>> +{ >>>> + struct s5p_cec_dev *cec = container_of(adap, struct s5p_cec_dev, >>>> adap); >>>> + int ret; >>>> + >>>> + if (enable) { >>>> + ret = pm_runtime_get_sync(cec->dev); >>>> + >>>> + adap->phys_addr = 0x100b; >>> >>> This is a bogus physical address. The actual physical address has to be >>> derived >>> from the EDID that is read by the HDMI transmitter. >>> >>> I think in the case of this driver it will have to be userspace that >>> assigns >>> the physical address after reading the EDID from drm/kms? >>> >>> How did you test this, Kamil? >> >> >> If I remember correctly, physical address has been derived from EDID in the >> userspace (it is available in /sys/class/drm/*) and passed to s5p-cec driver >> by >> appropriate ioctl. >> >> I don't know what is the reason for the above 'adap->phys_addr = 0x100b' >> assignment. > > At some point there was an idea to read the address from the EDID in > kernel. This static address was a hack until the code that reads the > EDID is written. As you say, it is much better to leave the address to > be set by the userspace. So this assignment serves no purpose anymore. Thank you, that's what I thought. It's fixed in my current tree. Still working on the CEC framework: I'm chasing race conditions and I suspect that there may be a bug in the adv7604 or adv7511 CEC implementation. Once I've sorted that I post a new version which has been tested a lot more thoroughly and should be complete except for the documentation. Regards, Hans
diff --git a/Documentation/devicetree/bindings/media/s5p-cec.txt b/Documentation/devicetree/bindings/media/s5p-cec.txt new file mode 100644 index 0000000..da63a4c --- /dev/null +++ b/Documentation/devicetree/bindings/media/s5p-cec.txt @@ -0,0 +1,31 @@ +* Samsung HDMI CEC driver + +The HDMI CEC module is present is Samsung SoCs and its purpose is to +handle communication between HDMI connected devices over the CEC bus. + +Required properties: + - compatible : value should be follwoing + "samsung,s5p-cec" + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : HDMI CEC interrupt number to the CPU. + - clocks : from common clock binding: handle to HDMI CEC clock. + - clock-names : from common clock binding: must contain "hdmicec", + corresponding to entry in the clocks property. + - samsung,syscon-phandle - phandle to the PMU system controller + +Example: + +hdmicec: cec@100B0000 { + compatible = "samsung,s5p-cec"; + reg = <0x100B0000 0x200>; + interrupts = <0 114 0>; + clocks = <&clock CLK_HDMI_CEC>; + clock-names = "hdmicec"; + samsung,syscon-phandle = <&pmu_system_controller>; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_cec>; + status = "okay"; +}; diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig index 4776a8c..d3843fc 100644 --- a/drivers/media/platform/Kconfig +++ b/drivers/media/platform/Kconfig @@ -157,6 +157,16 @@ config VIDEO_MEM2MEM_DEINTERLACE help Generic deinterlacing V4L2 driver. +config VIDEO_SAMSUNG_S5P_CEC + tristate "Samsung S5P CEC driver" + depends on CEC && VIDEO_DEV && VIDEO_V4L2 && (PLAT_S5P || ARCH_EXYNOS) + default n + ---help--- + This is a driver for Samsung S5P HDMI CEC interface. It uses the + generic CEC framework interface. + CEC bus is present in the HDMI connector and enables communication + between compatible devices. + config VIDEO_SAMSUNG_S5P_G2D tristate "Samsung S5P and EXYNOS4 G2D 2d graphics accelerator driver" depends on VIDEO_DEV && VIDEO_V4L2 diff --git a/drivers/media/platform/Makefile b/drivers/media/platform/Makefile index 114f9ab..95dd78d 100644 --- a/drivers/media/platform/Makefile +++ b/drivers/media/platform/Makefile @@ -27,6 +27,7 @@ obj-$(CONFIG_VIDEO_MEM2MEM_DEINTERLACE) += m2m-deinterlace.o obj-$(CONFIG_VIDEO_S3C_CAMIF) += s3c-camif/ obj-$(CONFIG_VIDEO_SAMSUNG_EXYNOS4_IS) += exynos4-is/ +obj-$(CONFIG_VIDEO_SAMSUNG_S5P_CEC) += s5p-cec/ obj-$(CONFIG_VIDEO_SAMSUNG_S5P_JPEG) += s5p-jpeg/ obj-$(CONFIG_VIDEO_SAMSUNG_S5P_MFC) += s5p-mfc/ obj-$(CONFIG_VIDEO_SAMSUNG_S5P_TV) += s5p-tv/ diff --git a/drivers/media/platform/s5p-cec/Makefile b/drivers/media/platform/s5p-cec/Makefile new file mode 100644 index 0000000..0e2cf45 --- /dev/null +++ b/drivers/media/platform/s5p-cec/Makefile @@ -0,0 +1,2 @@ +obj-$(CONFIG_VIDEO_SAMSUNG_S5P_CEC) += s5p-cec.o +s5p-cec-y += s5p_cec.o exynos_hdmi_cecctrl.o diff --git a/drivers/media/platform/s5p-cec/exynos_hdmi_cec.h b/drivers/media/platform/s5p-cec/exynos_hdmi_cec.h new file mode 100644 index 0000000..d008695 --- /dev/null +++ b/drivers/media/platform/s5p-cec/exynos_hdmi_cec.h @@ -0,0 +1,37 @@ +/* drivers/media/platform/s5p-cec/exynos_hdmi_cec.h + * + * Copyright (c) 2010, 2014 Samsung Electronics + * http://www.samsung.com/ + * + * Header file for interface of Samsung Exynos hdmi cec hardware + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef _EXYNOS_HDMI_CEC_H_ +#define _EXYNOS_HDMI_CEC_H_ __FILE__ + +#include <linux/regmap.h> +#include <linux/miscdevice.h> +#include "s5p_cec.h" + +void s5p_cec_set_divider(struct s5p_cec_dev *cec); +void s5p_cec_enable_rx(struct s5p_cec_dev *cec); +void s5p_cec_mask_rx_interrupts(struct s5p_cec_dev *cec); +void s5p_cec_unmask_rx_interrupts(struct s5p_cec_dev *cec); +void s5p_cec_mask_tx_interrupts(struct s5p_cec_dev *cec); +void s5p_cec_unmask_tx_interrupts(struct s5p_cec_dev *cec); +void s5p_cec_reset(struct s5p_cec_dev *cec); +void s5p_cec_tx_reset(struct s5p_cec_dev *cec); +void s5p_cec_rx_reset(struct s5p_cec_dev *cec); +void s5p_cec_threshold(struct s5p_cec_dev *cec); +void s5p_cec_copy_packet(struct s5p_cec_dev *cec, char *data, size_t count); +void s5p_cec_set_addr(struct s5p_cec_dev *cec, u32 addr); +u32 s5p_cec_get_status(struct s5p_cec_dev *cec); +void s5p_clr_pending_tx(struct s5p_cec_dev *cec); +void s5p_clr_pending_rx(struct s5p_cec_dev *cec); +void s5p_cec_get_rx_buf(struct s5p_cec_dev *cec, u32 size, u8 *buffer); + +#endif /* _EXYNOS_HDMI_CEC_H_ */ diff --git a/drivers/media/platform/s5p-cec/exynos_hdmi_cecctrl.c b/drivers/media/platform/s5p-cec/exynos_hdmi_cecctrl.c new file mode 100644 index 0000000..134e50b --- /dev/null +++ b/drivers/media/platform/s5p-cec/exynos_hdmi_cecctrl.c @@ -0,0 +1,208 @@ +/* drivers/media/platform/s5p-cec/exynos_hdmi_cecctrl.c + * + * Copyright (c) 2009, 2014 Samsung Electronics + * http://www.samsung.com/ + * + * cec ftn file for Samsung TVOUT driver + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/io.h> +#include <linux/device.h> + +#include "exynos_hdmi_cec.h" +#include "regs-cec.h" + +#define S5P_HDMI_FIN 24000000 +#define CEC_DIV_RATIO 320000 + +#define CEC_MESSAGE_BROADCAST_MASK 0x0F +#define CEC_MESSAGE_BROADCAST 0x0F +#define CEC_FILTER_THRESHOLD 0x15 + +void s5p_cec_set_divider(struct s5p_cec_dev *cec) +{ + u32 div_ratio, div_val; + unsigned int reg; + + div_ratio = S5P_HDMI_FIN / CEC_DIV_RATIO - 1; + + if (regmap_read(cec->pmu, EXYNOS_HDMI_PHY_CONTROL, ®)) { + dev_err(cec->dev, "failed to read phy control\n"); + return; + } + + reg = (reg & ~(0x3FF << 16)) | (div_ratio << 16); + + if (regmap_write(cec->pmu, EXYNOS_HDMI_PHY_CONTROL, reg)) { + dev_err(cec->dev, "failed to write phy control\n"); + return; + } + + div_val = CEC_DIV_RATIO * 0.00005 - 1; + + writeb(0x0, cec->reg + S5P_CEC_DIVISOR_3); + writeb(0x0, cec->reg + S5P_CEC_DIVISOR_2); + writeb(0x0, cec->reg + S5P_CEC_DIVISOR_1); + writeb(div_val, cec->reg + S5P_CEC_DIVISOR_0); +} + +void s5p_cec_enable_rx(struct s5p_cec_dev *cec) +{ + u8 reg; + + reg = readb(cec->reg + S5P_CEC_RX_CTRL); + reg |= S5P_CEC_RX_CTRL_ENABLE; + writeb(reg, cec->reg + S5P_CEC_RX_CTRL); +} + +void s5p_cec_mask_rx_interrupts(struct s5p_cec_dev *cec) +{ + u8 reg; + + reg = readb(cec->reg + S5P_CEC_IRQ_MASK); + reg |= S5P_CEC_IRQ_RX_DONE; + reg |= S5P_CEC_IRQ_RX_ERROR; + writeb(reg, cec->reg + S5P_CEC_IRQ_MASK); +} + +void s5p_cec_unmask_rx_interrupts(struct s5p_cec_dev *cec) +{ + u8 reg; + + reg = readb(cec->reg + S5P_CEC_IRQ_MASK); + reg &= ~S5P_CEC_IRQ_RX_DONE; + reg &= ~S5P_CEC_IRQ_RX_ERROR; + writeb(reg, cec->reg + S5P_CEC_IRQ_MASK); +} + +void s5p_cec_mask_tx_interrupts(struct s5p_cec_dev *cec) +{ + u8 reg; + + reg = readb(cec->reg + S5P_CEC_IRQ_MASK); + reg |= S5P_CEC_IRQ_TX_DONE; + reg |= S5P_CEC_IRQ_TX_ERROR; + writeb(reg, cec->reg + S5P_CEC_IRQ_MASK); + +} + +void s5p_cec_unmask_tx_interrupts(struct s5p_cec_dev *cec) +{ + u8 reg; + + reg = readb(cec->reg + S5P_CEC_IRQ_MASK); + reg &= ~S5P_CEC_IRQ_TX_DONE; + reg &= ~S5P_CEC_IRQ_TX_ERROR; + writeb(reg, cec->reg + S5P_CEC_IRQ_MASK); +} + +void s5p_cec_reset(struct s5p_cec_dev *cec) +{ + u8 reg; + + writeb(S5P_CEC_RX_CTRL_RESET, cec->reg + S5P_CEC_RX_CTRL); + writeb(S5P_CEC_TX_CTRL_RESET, cec->reg + S5P_CEC_TX_CTRL); + + reg = readb(cec->reg + 0xc4); + reg &= ~0x1; + writeb(reg, cec->reg + 0xc4); +} + +void s5p_cec_tx_reset(struct s5p_cec_dev *cec) +{ + writeb(S5P_CEC_TX_CTRL_RESET, cec->reg + S5P_CEC_TX_CTRL); +} + +void s5p_cec_rx_reset(struct s5p_cec_dev *cec) +{ + u8 reg; + + writeb(S5P_CEC_RX_CTRL_RESET, cec->reg + S5P_CEC_RX_CTRL); + + reg = readb(cec->reg + 0xc4); + reg &= ~0x1; + writeb(reg, cec->reg + 0xc4); +} + +void s5p_cec_threshold(struct s5p_cec_dev *cec) +{ + writeb(CEC_FILTER_THRESHOLD, cec->reg + S5P_CEC_RX_FILTER_TH); + writeb(0, cec->reg + S5P_CEC_RX_FILTER_CTRL); +} + +void s5p_cec_copy_packet(struct s5p_cec_dev *cec, char *data, size_t count) +{ + char debug[40]; + int i = 0; + u8 reg; + + while (i < count) { + writeb(data[i], cec->reg + (S5P_CEC_TX_BUFF0 + (i * 4))); + sprintf(debug + i * 2, "%02x ", data[i]); + i++; + } + + writeb(count, cec->reg + S5P_CEC_TX_BYTES); + reg = readb(cec->reg + S5P_CEC_TX_CTRL); + reg |= S5P_CEC_TX_CTRL_START; + + if ((data[0] & CEC_MESSAGE_BROADCAST_MASK) == CEC_MESSAGE_BROADCAST) { + dev_dbg(cec->dev, "Broadcast"); + reg |= S5P_CEC_TX_CTRL_BCAST; + } else { + dev_dbg(cec->dev, "No Broadcast"); + reg &= ~S5P_CEC_TX_CTRL_BCAST; + } + + reg |= 0x50; + writeb(reg, cec->reg + S5P_CEC_TX_CTRL); + dev_dbg(cec->dev, "cec-tx: cec count(%d): %s", count, debug); +} + +void s5p_cec_set_addr(struct s5p_cec_dev *cec, u32 addr) +{ + writeb(addr & 0x0F, cec->reg + S5P_CEC_LOGIC_ADDR); +} + +u32 s5p_cec_get_status(struct s5p_cec_dev *cec) +{ + u32 status = 0; + + status = readb(cec->reg + S5P_CEC_STATUS_0); + status |= readb(cec->reg + S5P_CEC_STATUS_1) << 8; + status |= readb(cec->reg + S5P_CEC_STATUS_2) << 16; + status |= readb(cec->reg + S5P_CEC_STATUS_3) << 24; + + dev_dbg(cec->dev, "status = 0x%x!\n", status); + + return status; +} + +void s5p_clr_pending_tx(struct s5p_cec_dev *cec) +{ + writeb(S5P_CEC_IRQ_TX_DONE | S5P_CEC_IRQ_TX_ERROR, + cec->reg + S5P_CEC_IRQ_CLEAR); +} + +void s5p_clr_pending_rx(struct s5p_cec_dev *cec) +{ + writeb(S5P_CEC_IRQ_RX_DONE | S5P_CEC_IRQ_RX_ERROR, + cec->reg + S5P_CEC_IRQ_CLEAR); +} + +void s5p_cec_get_rx_buf(struct s5p_cec_dev *cec, u32 size, u8 *buffer) +{ + u32 i = 0; + char debug[40]; + + while (i < size) { + buffer[i] = readb(cec->reg + S5P_CEC_RX_BUFF0 + (i * 4)); + sprintf(debug + i * 2, "%02x ", buffer[i]); + i++; + } + dev_dbg(cec->dev, "cec-rx: cec size(%d): %s", size, debug); +} diff --git a/drivers/media/platform/s5p-cec/regs-cec.h b/drivers/media/platform/s5p-cec/regs-cec.h new file mode 100644 index 0000000..b2e7e12 --- /dev/null +++ b/drivers/media/platform/s5p-cec/regs-cec.h @@ -0,0 +1,96 @@ +/* drivers/media/platform/s5p-cec/regs-cec.h + * + * Copyright (c) 2010 Samsung Electronics + * http://www.samsung.com/ + * + * register header file for Samsung TVOUT driver + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __EXYNOS_REGS__H +#define __EXYNOS_REGS__H + +/* + * Register part + */ +#define S5P_CEC_STATUS_0 (0x0000) +#define S5P_CEC_STATUS_1 (0x0004) +#define S5P_CEC_STATUS_2 (0x0008) +#define S5P_CEC_STATUS_3 (0x000C) +#define S5P_CEC_IRQ_MASK (0x0010) +#define S5P_CEC_IRQ_CLEAR (0x0014) +#define S5P_CEC_LOGIC_ADDR (0x0020) +#define S5P_CEC_DIVISOR_0 (0x0030) +#define S5P_CEC_DIVISOR_1 (0x0034) +#define S5P_CEC_DIVISOR_2 (0x0038) +#define S5P_CEC_DIVISOR_3 (0x003C) + +#define S5P_CEC_TX_CTRL (0x0040) +#define S5P_CEC_TX_BYTES (0x0044) +#define S5P_CEC_TX_STAT0 (0x0060) +#define S5P_CEC_TX_STAT1 (0x0064) +#define S5P_CEC_TX_BUFF0 (0x0080) +#define S5P_CEC_TX_BUFF1 (0x0084) +#define S5P_CEC_TX_BUFF2 (0x0088) +#define S5P_CEC_TX_BUFF3 (0x008C) +#define S5P_CEC_TX_BUFF4 (0x0090) +#define S5P_CEC_TX_BUFF5 (0x0094) +#define S5P_CEC_TX_BUFF6 (0x0098) +#define S5P_CEC_TX_BUFF7 (0x009C) +#define S5P_CEC_TX_BUFF8 (0x00A0) +#define S5P_CEC_TX_BUFF9 (0x00A4) +#define S5P_CEC_TX_BUFF10 (0x00A8) +#define S5P_CEC_TX_BUFF11 (0x00AC) +#define S5P_CEC_TX_BUFF12 (0x00B0) +#define S5P_CEC_TX_BUFF13 (0x00B4) +#define S5P_CEC_TX_BUFF14 (0x00B8) +#define S5P_CEC_TX_BUFF15 (0x00BC) + +#define S5P_CEC_RX_CTRL (0x00C0) +#define S5P_CEC_RX_STAT0 (0x00E0) +#define S5P_CEC_RX_STAT1 (0x00E4) +#define S5P_CEC_RX_BUFF0 (0x0100) +#define S5P_CEC_RX_BUFF1 (0x0104) +#define S5P_CEC_RX_BUFF2 (0x0108) +#define S5P_CEC_RX_BUFF3 (0x010C) +#define S5P_CEC_RX_BUFF4 (0x0110) +#define S5P_CEC_RX_BUFF5 (0x0114) +#define S5P_CEC_RX_BUFF6 (0x0118) +#define S5P_CEC_RX_BUFF7 (0x011C) +#define S5P_CEC_RX_BUFF8 (0x0120) +#define S5P_CEC_RX_BUFF9 (0x0124) +#define S5P_CEC_RX_BUFF10 (0x0128) +#define S5P_CEC_RX_BUFF11 (0x012C) +#define S5P_CEC_RX_BUFF12 (0x0130) +#define S5P_CEC_RX_BUFF13 (0x0134) +#define S5P_CEC_RX_BUFF14 (0x0138) +#define S5P_CEC_RX_BUFF15 (0x013C) + +#define S5P_CEC_RX_FILTER_CTRL (0x0180) +#define S5P_CEC_RX_FILTER_TH (0x0184) + +/* + * Bit definition part + */ +#define S5P_CEC_IRQ_TX_DONE (1<<0) +#define S5P_CEC_IRQ_TX_ERROR (1<<1) +#define S5P_CEC_IRQ_RX_DONE (1<<4) +#define S5P_CEC_IRQ_RX_ERROR (1<<5) + +#define S5P_CEC_TX_CTRL_START (1<<0) +#define S5P_CEC_TX_CTRL_BCAST (1<<1) +#define S5P_CEC_TX_CTRL_RETRY (0x04<<4) +#define S5P_CEC_TX_CTRL_RESET (1<<7) + +#define S5P_CEC_RX_CTRL_ENABLE (1<<0) +#define S5P_CEC_RX_CTRL_RESET (1<<7) + +#define S5P_CEC_LOGIC_ADDR_MASK (0xF) + +/* PMU Registers for PHY */ +#define EXYNOS_HDMI_PHY_CONTROL 0x700 + +#endif /* __EXYNOS_REGS__H */ diff --git a/drivers/media/platform/s5p-cec/s5p_cec.c b/drivers/media/platform/s5p-cec/s5p_cec.c new file mode 100644 index 0000000..0f16d00 --- /dev/null +++ b/drivers/media/platform/s5p-cec/s5p_cec.c @@ -0,0 +1,283 @@ +/* drivers/media/platform/s5p-cec/s5p_cec.c + * + * Samsung S5P CEC driver + * + * Copyright (c) 2014 Samsung Electronics Co., Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This driver is based on the "cec interface driver for exynos soc" by + * SangPil Moon. + */ + +#include <linux/clk.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pm_runtime.h> +#include <linux/timer.h> +#include <linux/version.h> +#include <linux/workqueue.h> +#include <media/cec.h> + +#include "exynos_hdmi_cec.h" +#include "regs-cec.h" +#include "s5p_cec.h" + +#define CEC_NAME "s5p-cec" + +static int debug; +module_param(debug, int, 0644); +MODULE_PARM_DESC(debug, "debug level (0-2)"); + +static int s5p_cec_enable(struct cec_adapter *adap, bool enable) +{ + struct s5p_cec_dev *cec = container_of(adap, struct s5p_cec_dev, adap); + int ret; + + if (enable) { + ret = pm_runtime_get_sync(cec->dev); + + adap->phys_addr = 0x100b; + s5p_cec_reset(cec); + + s5p_cec_set_divider(cec); + s5p_cec_threshold(cec); + + s5p_cec_unmask_tx_interrupts(cec); + s5p_cec_unmask_rx_interrupts(cec); + s5p_cec_enable_rx(cec); + } else { + s5p_cec_mask_tx_interrupts(cec); + s5p_cec_mask_rx_interrupts(cec); + pm_runtime_disable(cec->dev); + } + + return 0; +} + +static int s5p_cec_log_addr(struct cec_adapter *adap, u8 addr) +{ + struct s5p_cec_dev *cec = container_of(adap, struct s5p_cec_dev, adap); + + s5p_cec_set_addr(cec, addr); + return 0; +} + +static int s5p_cec_transmit(struct cec_adapter *adap, struct cec_msg *msg) +{ + struct s5p_cec_dev *cec = container_of(adap, struct s5p_cec_dev, adap); + + s5p_cec_copy_packet(cec, msg->msg, msg->len); + return 0; +} + +static void s5p_cec_transmit_timed_out(struct cec_adapter *adap) +{ + +} + +static irqreturn_t s5p_cec_irq_handler(int irq, void *priv) +{ + struct s5p_cec_dev *cec = priv; + u32 status = 0; + + status = s5p_cec_get_status(cec); + + dev_dbg(cec->dev, "irq received\n"); + + if (status & CEC_STATUS_TX_DONE) { + if (status & CEC_STATUS_TX_ERROR) { + dev_dbg(cec->dev, "CEC_STATUS_TX_ERROR set\n"); + cec->tx = STATE_ERROR; + } else { + dev_dbg(cec->dev, "CEC_STATUS_TX_DONE\n"); + cec->tx = STATE_DONE; + } + s5p_clr_pending_tx(cec); + } + + if (status & CEC_STATUS_RX_DONE) { + if (status & CEC_STATUS_RX_ERROR) { + dev_dbg(cec->dev, "CEC_STATUS_RX_ERROR set\n"); + s5p_cec_rx_reset(cec); + s5p_cec_enable_rx(cec); + } else { + dev_dbg(cec->dev, "CEC_STATUS_RX_DONE set\n"); + if (cec->rx != STATE_IDLE) + dev_dbg(cec->dev, "Buffer overrun (worker did not process previous message)\n"); + cec->rx = STATE_BUSY; + cec->msg.len = status >> 24; + cec->msg.status = CEC_RX_STATUS_READY; + s5p_cec_get_rx_buf(cec, cec->msg.len, + cec->msg.msg); + cec->rx = STATE_DONE; + s5p_cec_enable_rx(cec); + } + /* Clear interrupt pending bit */ + s5p_clr_pending_rx(cec); + } + return IRQ_WAKE_THREAD; +} + +static irqreturn_t s5p_cec_irq_handler_thread(int irq, void *priv) +{ + struct s5p_cec_dev *cec = priv; + + dev_dbg(cec->dev, "irq processing thread\n"); + switch (cec->tx) { + case STATE_DONE: + cec_transmit_done(&cec->adap, CEC_TX_STATUS_OK); + cec->tx = STATE_IDLE; + break; + case STATE_ERROR: + cec_transmit_done(&cec->adap, CEC_TX_STATUS_RETRY_TIMEOUT); + cec->tx = STATE_IDLE; + break; + case STATE_BUSY: + dev_err(cec->dev, "state set to busy, this should not occur here\n"); + break; + default: + break; + } + + switch (cec->rx) { + case STATE_DONE: + cec_received_msg(&cec->adap, &cec->msg); + cec->rx = STATE_IDLE; + default: + break; + }; + + return IRQ_HANDLED; +} + +static int s5p_cec_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct resource *res; + struct s5p_cec_dev *cec; + int ret; + + cec = devm_kzalloc(&pdev->dev, sizeof(*cec), GFP_KERNEL); + if (!dev) + return -ENOMEM; + + cec->dev = dev; + + cec->irq = platform_get_irq(pdev, 0); + if (IS_ERR_VALUE(cec->irq)) + return cec->irq; + + ret = devm_request_threaded_irq(dev, cec->irq, s5p_cec_irq_handler, + s5p_cec_irq_handler_thread, 0, pdev->name, cec); + if (IS_ERR_VALUE(ret)) + return ret; + + cec->clk = devm_clk_get(dev, "hdmicec"); + if (IS_ERR(cec->clk)) + return PTR_ERR(cec->clk); + + cec->pmu = syscon_regmap_lookup_by_phandle(dev->of_node, + "samsung,syscon-phandle"); + if (IS_ERR(cec->pmu)) + return -EPROBE_DEFER; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + cec->reg = devm_ioremap_resource(dev, res); + if (IS_ERR(cec->reg)) + return PTR_ERR(cec->reg); + + cec->adap.available_log_addrs = 1; + cec->adap.adap_enable = s5p_cec_enable; + cec->adap.adap_log_addr = s5p_cec_log_addr; + cec->adap.adap_transmit = s5p_cec_transmit; + cec->adap.adap_transmit_timed_out = s5p_cec_transmit_timed_out; + cec_create_adapter(&cec->adap, CEC_NAME, CEC_CAP_STATE | + CEC_CAP_LOG_ADDRS | CEC_CAP_TRANSMIT | + CEC_CAP_RECEIVE, true, THIS_MODULE, &pdev->dev); + + platform_set_drvdata(pdev, cec); + pm_runtime_enable(dev); + + dev_dbg(dev, "successfuly probed\n"); + return 0; +} + +static int s5p_cec_remove(struct platform_device *pdev) +{ + struct s5p_cec_dev *cec = platform_get_drvdata(pdev); + + cec_delete_adapter(&cec->adap); + pm_runtime_disable(&pdev->dev); + return 0; +} + +static int s5p_cec_runtime_suspend(struct device *dev) +{ + struct s5p_cec_dev *cec = dev_get_drvdata(dev); + + clk_disable_unprepare(cec->clk); + return 0; +} + +static int s5p_cec_runtime_resume(struct device *dev) +{ + struct s5p_cec_dev *cec = dev_get_drvdata(dev); + int ret; + + ret = clk_prepare_enable(cec->clk); + if (ret < 0) + return ret; + return 0; +} + +static int s5p_cec_suspend(struct device *dev) +{ + if (pm_runtime_suspended(dev)) + return 0; + return s5p_cec_runtime_suspend(dev); +} + +static int s5p_cec_resume(struct device *dev) +{ + if (pm_runtime_suspended(dev)) + return 0; + return s5p_cec_runtime_resume(dev); +} + +static const struct dev_pm_ops s5p_cec_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(s5p_cec_suspend, s5p_cec_resume) + SET_RUNTIME_PM_OPS(s5p_cec_runtime_suspend, s5p_cec_runtime_resume, + NULL) +}; + +static const struct of_device_id s5p_cec_match[] = { + { + .compatible = "samsung,s5p-cec", + }, + {}, +}; + +static struct platform_driver s5p_cec_pdrv = { + .probe = s5p_cec_probe, + .remove = s5p_cec_remove, + .driver = { + .name = CEC_NAME, + .owner = THIS_MODULE, + .of_match_table = s5p_cec_match, + .pm = &s5p_cec_pm_ops, + }, +}; + +module_platform_driver(s5p_cec_pdrv); + +MODULE_AUTHOR("Kamil Debski <kamil@wypas.org>"); +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("Samsung S5P CEC driver"); diff --git a/drivers/media/platform/s5p-cec/s5p_cec.h b/drivers/media/platform/s5p-cec/s5p_cec.h new file mode 100644 index 0000000..d6ffd92 --- /dev/null +++ b/drivers/media/platform/s5p-cec/s5p_cec.h @@ -0,0 +1,76 @@ +/* drivers/media/platform/s5p-cec/s5p_cec.h + * + * Samsung S5P HDMI CEC driver + * + * Copyright (c) 2014 Samsung Electronics Co., Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef _S5P_CEC_H_ +#define _S5P_CEC_H_ __FILE__ + +#include <linux/clk.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pm_runtime.h> +#include <linux/timer.h> +#include <linux/version.h> +#include <linux/workqueue.h> +#include <media/cec.h> + +#include "exynos_hdmi_cec.h" +#include "regs-cec.h" +#include "s5p_cec.h" + +#define CEC_NAME "s5p-cec" + +#define CEC_STATUS_TX_RUNNING (1 << 0) +#define CEC_STATUS_TX_TRANSFERRING (1 << 1) +#define CEC_STATUS_TX_DONE (1 << 2) +#define CEC_STATUS_TX_ERROR (1 << 3) +#define CEC_STATUS_TX_BYTES (0xFF << 8) +#define CEC_STATUS_RX_RUNNING (1 << 16) +#define CEC_STATUS_RX_RECEIVING (1 << 17) +#define CEC_STATUS_RX_DONE (1 << 18) +#define CEC_STATUS_RX_ERROR (1 << 19) +#define CEC_STATUS_RX_BCAST (1 << 20) +#define CEC_STATUS_RX_BYTES (0xFF << 24) + +#define CEC_WORKER_TX_DONE (1 << 0) +#define CEC_WORKER_RX_MSG (1 << 1) + +/* CEC Rx buffer size */ +#define CEC_RX_BUFF_SIZE 16 +/* CEC Tx buffer size */ +#define CEC_TX_BUFF_SIZE 16 + +enum cec_state { + STATE_IDLE, + STATE_BUSY, + STATE_DONE, + STATE_ERROR +}; + +struct s5p_cec_dev { + struct cec_adapter adap; + struct clk *clk; + struct device *dev; + struct mutex lock; + struct regmap *pmu; + int irq; + void __iomem *reg; + + enum cec_state rx; + enum cec_state tx; + struct cec_msg msg; +}; + +#endif /* _S5P_CEC_H_ */