@@ -160,8 +160,6 @@ static int omap_connector_mode_valid(struct drm_connector *connector,
int r, ret = MODE_BAD;
drm_display_mode_to_videomode(mode, &vm);
- vm.flags |= DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE |
- DISPLAY_FLAGS_SYNC_NEGEDGE;
mode->vrefresh = drm_mode_vrefresh(mode);
/*
@@ -427,6 +427,11 @@ static void omap_crtc_mode_set_nofb(struct drm_crtc *crtc)
{
struct omap_crtc *omap_crtc = to_omap_crtc(crtc);
struct drm_display_mode *mode = &crtc->state->adjusted_mode;
+ struct omap_drm_private *priv = crtc->dev->dev_private;
+ const u32 flags_mask = DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_DE_LOW |
+ DISPLAY_FLAGS_PIXDATA_POSEDGE | DISPLAY_FLAGS_PIXDATA_NEGEDGE |
+ DISPLAY_FLAGS_SYNC_POSEDGE | DISPLAY_FLAGS_SYNC_NEGEDGE;
+ int i;
DBG("%s: set mode: %d:\"%s\" %d %d %d %d %d %d %d %d %d %d 0x%x 0x%x",
omap_crtc->name, mode->base.id, mode->name,
@@ -436,9 +441,26 @@ static void omap_crtc_mode_set_nofb(struct drm_crtc *crtc)
mode->type, mode->flags);
drm_display_mode_to_videomode(mode, &omap_crtc->vm);
- omap_crtc->vm.flags |= DISPLAY_FLAGS_DE_HIGH |
- DISPLAY_FLAGS_PIXDATA_POSEDGE |
- DISPLAY_FLAGS_SYNC_NEGEDGE;
+
+ for (i = 0; i < priv->num_encoders; ++i) {
+ struct drm_encoder *encoder = priv->encoders[i];
+
+ if (encoder->crtc == crtc) {
+ struct omap_dss_device *dssdev;
+
+ dssdev = omap_encoder_get_dssdev(encoder);
+
+ if (dssdev) {
+ struct videomode vm = {0};
+
+ dssdev->driver->get_timings(dssdev, &vm);
+
+ omap_crtc->vm.flags |= vm.flags & flags_mask;
+ }
+
+ break;
+ }
+ }
}
static int omap_crtc_atomic_check(struct drm_crtc *crtc,
At the moment VSYNC/HSYNC/DE high/low flags set by the panel/encoder drivers get lost when the videotimings are translated to DRM's videomode, as DRM's mode does not have corresponding flags. DRM has bus-flags for this purpose, and while it lacks a few flags at the moment, it should be used here. However, until we rewrite omapdrm's device model, using bus-flags is rather difficult. As a short term fix, this patch makes sure that every time the videomode is set in omap_crtc_mode_set_nofb(), the driver asks for the SYNC/DE flags from the panel/encoder drivers, and thus we get the correct flags into use. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> --- drivers/gpu/drm/omapdrm/omap_connector.c | 2 -- drivers/gpu/drm/omapdrm/omap_crtc.c | 28 +++++++++++++++++++++++++--- 2 files changed, 25 insertions(+), 5 deletions(-)