diff mbox

[v3,3/6] drm/bridge/synopsys: Add MIPI DSI host controller bridge

Message ID 1496414235-20098-4-git-send-email-philippe.cornu@st.com (mailing list archive)
State New, archived
Headers show

Commit Message

Philippe CORNU June 2, 2017, 2:37 p.m. UTC
Add a Synopsys Designware MIPI DSI host DRM bridge driver, based on the
Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.

Signed-off-by: Philippe CORNU <philippe.cornu@st.com>
---
 drivers/gpu/drm/bridge/synopsys/Kconfig       |    9 +
 drivers/gpu/drm/bridge/synopsys/Makefile      |    2 +
 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 1022 +++++++++++++++++++++++++
 include/drm/bridge/dw_mipi_dsi.h              |   42 +
 4 files changed, 1075 insertions(+)
 create mode 100644 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
 create mode 100644 include/drm/bridge/dw_mipi_dsi.h

Comments

Neil Armstrong June 6, 2017, 8:07 a.m. UTC | #1
On 06/02/2017 04:37 PM, Philippe CORNU wrote:
> Add a Synopsys Designware MIPI DSI host DRM bridge driver, based on the
> Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.

Hi Philippe,

Small nit, but please use "DesignWare" everywhere if possible.

Thanks,
Neil

> 
> Signed-off-by: Philippe CORNU <philippe.cornu@st.com>
> ---
>  drivers/gpu/drm/bridge/synopsys/Kconfig       |    9 +
>  drivers/gpu/drm/bridge/synopsys/Makefile      |    2 +
>  drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 1022 +++++++++++++++++++++++++
>  include/drm/bridge/dw_mipi_dsi.h              |   42 +
>  4 files changed, 1075 insertions(+)
>  create mode 100644 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
>  create mode 100644 include/drm/bridge/dw_mipi_dsi.h
> 
> diff --git a/drivers/gpu/drm/bridge/synopsys/Kconfig b/drivers/gpu/drm/bridge/synopsys/Kconfig
> index 40d2827..d7fbdff 100644
> --- a/drivers/gpu/drm/bridge/synopsys/Kconfig
> +++ b/drivers/gpu/drm/bridge/synopsys/Kconfig
> @@ -21,3 +21,12 @@ config DRM_DW_HDMI_I2S_AUDIO
>  	help
>  	  Support the I2S Audio interface which is part of the Synopsys
>  	  Designware HDMI block.
Yes I know this one is bad....

> +
> +config DRM_DW_MIPI_DSI
> +	tristate "Synopsys DesignWare MIPI DSI host controller bridge"
> +	select DRM_KMS_HELPER
> +	select DRM_MIPI_DSI
> +	select DRM_PANEL
> +	help
> +	  Choose this if you want to use the Synopsys DesignWare MIPI DSI host
> +	  controller bridge.
> diff --git a/drivers/gpu/drm/bridge/synopsys/Makefile b/drivers/gpu/drm/bridge/synopsys/Makefile
> index 17aa7a6..5f57d36 100644
> --- a/drivers/gpu/drm/bridge/synopsys/Makefile
> +++ b/drivers/gpu/drm/bridge/synopsys/Makefile
> @@ -3,3 +3,5 @@
>  obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
>  obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
>  obj-$(CONFIG_DRM_DW_HDMI_I2S_AUDIO) += dw-hdmi-i2s-audio.o
> +
> +obj-$(CONFIG_DRM_DW_MIPI_DSI) += dw-mipi-dsi.o
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
> new file mode 100644
> index 0000000..6b25629
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
> @@ -0,0 +1,1022 @@
> +/*
> + * Copyright (c) 2016, Fuzhou Rockchip Electronics Co., Ltd
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * Modified by Philippe Cornu <philippe.cornu@st.com>
> + * This generic Synopsys Designware MIPI DSI host driver is based on the
------------------------------/\
Like here

> + * Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/component.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/reset.h>
> +#include <drm/drmP.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_crtc.h>
> +#include <drm/drm_crtc_helper.h>
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_of.h>
> +#include <drm/drm_panel.h>
> +#include <drm/bridge/dw_mipi_dsi.h>
> +#include <video/mipi_display.h>
> +
> +#define DSI_VERSION			0x00
> +#define DSI_PWR_UP			0x04
> +#define RESET				0
> +#define POWERUP				BIT(0)
> +
> +#define DSI_CLKMGR_CFG			0x08
> +#define TO_CLK_DIVIDSION(div)		(((div) & 0xff) << 8)
> +#define TX_ESC_CLK_DIVIDSION(div)	(((div) & 0xff) << 0)
> +
> +#define DSI_DPI_VCID			0x0c
> +#define DPI_VID(vid)			(((vid) & 0x3) << 0)
> +
> +#define DSI_DPI_COLOR_CODING		0x10
> +#define EN18_LOOSELY			BIT(8)
> +#define DPI_COLOR_CODING_16BIT_1	0x0
> +#define DPI_COLOR_CODING_16BIT_2	0x1
> +#define DPI_COLOR_CODING_16BIT_3	0x2
> +#define DPI_COLOR_CODING_18BIT_1	0x3
> +#define DPI_COLOR_CODING_18BIT_2	0x4
> +#define DPI_COLOR_CODING_24BIT		0x5
> +
> +#define DSI_DPI_CFG_POL			0x14
> +#define COLORM_ACTIVE_LOW		BIT(4)
> +#define SHUTD_ACTIVE_LOW		BIT(3)
> +#define HSYNC_ACTIVE_LOW		BIT(2)
> +#define VSYNC_ACTIVE_LOW		BIT(1)
> +#define DATAEN_ACTIVE_LOW		BIT(0)
> +
> +#define DSI_DPI_LP_CMD_TIM		0x18
> +#define OUTVACT_LPCMD_TIME(p)		(((p) & 0xff) << 16)
> +#define INVACT_LPCMD_TIME(p)		((p) & 0xff)
> +
> +#define DSI_DBI_CFG			0x20
> +#define DSI_DBI_CMDSIZE			0x28
> +
> +#define DSI_PCKHDL_CFG			0x2c
> +#define EN_CRC_RX			BIT(4)
> +#define EN_ECC_RX			BIT(3)
> +#define EN_BTA				BIT(2)
> +#define EN_EOTP_RX			BIT(1)
> +#define EN_EOTP_TX			BIT(0)
> +
> +#define DSI_MODE_CFG			0x34
> +#define ENABLE_VIDEO_MODE		0
> +#define ENABLE_CMD_MODE			BIT(0)
> +
> +#define DSI_VID_MODE_CFG		0x38
> +#define FRAME_BTA_ACK			BIT(14)
> +#define ENABLE_LOW_POWER		(0x3f << 8)
> +#define ENABLE_LOW_POWER_MASK		(0x3f << 8)
> +#define VID_MODE_TYPE_NON_BURST_SYNC_PULSES	0x0
> +#define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS	0x1
> +#define VID_MODE_TYPE_BURST			0x2
> +#define VID_MODE_TYPE_MASK			0x3
> +
> +#define DSI_VID_PKT_SIZE		0x3c
> +#define VID_PKT_SIZE(p)			(((p) & 0x3fff) << 0)
> +#define VID_PKT_MAX_SIZE		0x3fff
> +
> +#define DSI_VID_HSA_TIME		0x48
> +#define DSI_VID_HBP_TIME		0x4c
> +#define DSI_VID_HLINE_TIME		0x50
> +#define DSI_VID_VSA_LINES		0x54
> +#define DSI_VID_VBP_LINES		0x58
> +#define DSI_VID_VFP_LINES		0x5c
> +#define DSI_VID_VACTIVE_LINES		0x60
> +#define DSI_CMD_MODE_CFG		0x68
> +#define MAX_RD_PKT_SIZE_LP		BIT(24)
> +#define DCS_LW_TX_LP			BIT(19)
> +#define DCS_SR_0P_TX_LP			BIT(18)
> +#define DCS_SW_1P_TX_LP			BIT(17)
> +#define DCS_SW_0P_TX_LP			BIT(16)
> +#define GEN_LW_TX_LP			BIT(14)
> +#define GEN_SR_2P_TX_LP			BIT(13)
> +#define GEN_SR_1P_TX_LP			BIT(12)
> +#define GEN_SR_0P_TX_LP			BIT(11)
> +#define GEN_SW_2P_TX_LP			BIT(10)
> +#define GEN_SW_1P_TX_LP			BIT(9)
> +#define GEN_SW_0P_TX_LP			BIT(8)
> +#define EN_ACK_RQST			BIT(1)
> +#define EN_TEAR_FX			BIT(0)
> +
> +#define CMD_MODE_ALL_LP			(MAX_RD_PKT_SIZE_LP | \
> +					 DCS_LW_TX_LP | \
> +					 DCS_SR_0P_TX_LP | \
> +					 DCS_SW_1P_TX_LP | \
> +					 DCS_SW_0P_TX_LP | \
> +					 GEN_LW_TX_LP | \
> +					 GEN_SR_2P_TX_LP | \
> +					 GEN_SR_1P_TX_LP | \
> +					 GEN_SR_0P_TX_LP | \
> +					 GEN_SW_2P_TX_LP | \
> +					 GEN_SW_1P_TX_LP | \
> +					 GEN_SW_0P_TX_LP)
> +
> +#define DSI_GEN_HDR			0x6c
> +#define GEN_HDATA(data)			(((data) & 0xffff) << 8)
> +#define GEN_HDATA_MASK			(0xffff << 8)
> +#define GEN_HTYPE(type)			(((type) & 0xff) << 0)
> +#define GEN_HTYPE_MASK			0xff
> +
> +#define DSI_GEN_PLD_DATA		0x70
> +
> +#define DSI_CMD_PKT_STATUS		0x74
> +#define GEN_CMD_EMPTY			BIT(0)
> +#define GEN_CMD_FULL			BIT(1)
> +#define GEN_PLD_W_EMPTY			BIT(2)
> +#define GEN_PLD_W_FULL			BIT(3)
> +#define GEN_PLD_R_EMPTY			BIT(4)
> +#define GEN_PLD_R_FULL			BIT(5)
> +#define GEN_RD_CMD_BUSY			BIT(6)
> +
> +#define DSI_TO_CNT_CFG			0x78
> +#define HSTX_TO_CNT(p)			(((p) & 0xffff) << 16)
> +#define LPRX_TO_CNT(p)			((p) & 0xffff)
> +
> +#define DSI_BTA_TO_CNT			0x8c
> +#define DSI_LPCLK_CTRL			0x94
> +#define AUTO_CLKLANE_CTRL		BIT(1)
> +#define PHY_TXREQUESTCLKHS		BIT(0)
> +
> +#define DSI_PHY_TMR_LPCLK_CFG		0x98
> +#define PHY_CLKHS2LP_TIME(lbcc)		(((lbcc) & 0x3ff) << 16)
> +#define PHY_CLKLP2HS_TIME(lbcc)		((lbcc) & 0x3ff)
> +
> +#define DSI_PHY_TMR_CFG			0x9c
> +#define PHY_HS2LP_TIME(lbcc)		(((lbcc) & 0xff) << 24)
> +#define PHY_LP2HS_TIME(lbcc)		(((lbcc) & 0xff) << 16)
> +#define MAX_RD_TIME(lbcc)		((lbcc) & 0x7fff)
> +
> +#define DSI_PHY_RSTZ			0xa0
> +#define PHY_DISFORCEPLL			0
> +#define PHY_ENFORCEPLL			BIT(3)
> +#define PHY_DISABLECLK			0
> +#define PHY_ENABLECLK			BIT(2)
> +#define PHY_RSTZ			0
> +#define PHY_UNRSTZ			BIT(1)
> +#define PHY_SHUTDOWNZ			0
> +#define PHY_UNSHUTDOWNZ			BIT(0)
> +
> +#define DSI_PHY_IF_CFG			0xa4
> +#define N_LANES(n)			((((n) - 1) & 0x3) << 0)
> +#define PHY_STOP_WAIT_TIME(cycle)	(((cycle) & 0xff) << 8)
> +
> +#define DSI_PHY_STATUS			0xb0
> +#define LOCK				BIT(0)
> +#define STOP_STATE_CLK_LANE		BIT(2)
> +
> +#define DSI_PHY_TST_CTRL0		0xb4
> +#define PHY_TESTCLK			BIT(1)
> +#define PHY_UNTESTCLK			0
> +#define PHY_TESTCLR			BIT(0)
> +#define PHY_UNTESTCLR			0
> +
> +#define DSI_PHY_TST_CTRL1		0xb8
> +#define PHY_TESTEN			BIT(16)
> +#define PHY_UNTESTEN			0
> +#define PHY_TESTDOUT(n)			(((n) & 0xff) << 8)
> +#define PHY_TESTDIN(n)			(((n) & 0xff) << 0)
> +
> +#define DSI_INT_ST0			0xbc
> +#define DSI_INT_ST1			0xc0
> +#define DSI_INT_MSK0			0xc4
> +#define DSI_INT_MSK1			0xc8
> +
> +#define PHY_STATUS_TIMEOUT_US		10000
> +#define CMD_PKT_STATUS_TIMEOUT_US	20000
> +
> +struct dw_mipi_dsi {
> +	struct drm_bridge bridge;
> +	struct drm_connector connector;
> +	struct mipi_dsi_host dsi_host;
> +	struct drm_panel *panel;
> +	struct device *dev;
> +	void __iomem *base;
> +
> +	struct clk *pclk;
> +
> +	int dpms_mode;
> +	unsigned int lane_mbps; /* per lane */
> +	u32 channel;
> +	u32 lanes;
> +	u32 format;
> +	unsigned long mode_flags;
> +
> +	const struct dw_mipi_dsi_plat_data *plat_data;
> +};
> +
> +/*
> + * The controller should generate 2 frames before
> + * preparing the peripheral.
> + */
> +static void dw_mipi_dsi_wait_for_two_frames(struct drm_display_mode *mode)
> +{
> +	int refresh, two_frames;
> +
> +	refresh = drm_mode_vrefresh(mode);
> +	two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2;
> +	msleep(two_frames);
> +}
> +
> +static inline struct dw_mipi_dsi *host_to_dsi(struct mipi_dsi_host *host)
> +{
> +	return container_of(host, struct dw_mipi_dsi, dsi_host);
> +}
> +
> +static inline struct dw_mipi_dsi *con_to_dsi(struct drm_connector *con)
> +{
> +	return container_of(con, struct dw_mipi_dsi, connector);
> +}
> +
> +static inline struct dw_mipi_dsi *bridge_to_dsi(struct drm_bridge *bridge)
> +{
> +	return container_of(bridge, struct dw_mipi_dsi, bridge);
> +}
> +
> +static inline void dsi_write(struct dw_mipi_dsi *dsi, u32 reg, u32 val)
> +{
> +	writel_relaxed(val, dsi->base + reg);
> +}
> +
> +static inline u32 dsi_read(struct dw_mipi_dsi *dsi, u32 reg)
> +{
> +	return readl_relaxed(dsi->base + reg);
> +}
> +
> +static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
> +				   struct mipi_dsi_device *device)
> +{
> +	struct dw_mipi_dsi *dsi = host_to_dsi(host);
> +
> +	if (device->lanes > dsi->plat_data->max_data_lanes) {
> +		dev_err(dsi->dev, "the number of data lanes(%u) is too many\n",
> +			device->lanes);
> +		return -EINVAL;
> +	}
> +
> +	dsi->lanes = device->lanes;
> +	dsi->channel = device->channel;
> +	dsi->format = device->format;
> +	dsi->mode_flags = device->mode_flags;
> +	dsi->panel = of_drm_find_panel(device->dev.of_node);
> +	if (dsi->panel)
> +		return drm_panel_attach(dsi->panel, &dsi->connector);
> +
> +	return -EINVAL;
> +}
> +
> +static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
> +				   struct mipi_dsi_device *device)
> +{
> +	struct dw_mipi_dsi *dsi = host_to_dsi(host);
> +
> +	drm_panel_detach(dsi->panel);
> +
> +	return 0;
> +}
> +
> +static void dw_mipi_message_config(struct dw_mipi_dsi *dsi,
> +				   const struct mipi_dsi_msg *msg)
> +{
> +	bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM;
> +	u32 val = 0;
> +
> +	if (msg->flags & MIPI_DSI_MSG_REQ_ACK)
> +		val |= EN_ACK_RQST;
> +	if (lpm)
> +		val |= CMD_MODE_ALL_LP;
> +
> +	dsi_write(dsi, DSI_LPCLK_CTRL, lpm ? 0 : PHY_TXREQUESTCLKHS);
> +	dsi_write(dsi, DSI_CMD_MODE_CFG, val);
> +}
> +
> +static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
> +{
> +	int ret;
> +	u32 val, mask;
> +
> +	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
> +				 val, !(val & GEN_CMD_FULL), 1000,
> +				 CMD_PKT_STATUS_TIMEOUT_US);
> +	if (ret < 0) {
> +		dev_err(dsi->dev, "failed to get available command FIFO\n");
> +		return ret;
> +	}
> +
> +	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
> +
> +	mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
> +	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
> +				 val, (val & mask) == mask,
> +				 1000, CMD_PKT_STATUS_TIMEOUT_US);
> +	if (ret < 0) {
> +		dev_err(dsi->dev, "failed to write command FIFO\n");
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
> +				       const struct mipi_dsi_msg *msg)
> +{
> +	const u8 *tx_buf = msg->tx_buf;
> +	u16 data = 0;
> +	u32 val;
> +
> +	if (msg->tx_len > 0)
> +		data |= tx_buf[0];
> +	if (msg->tx_len > 1)
> +		data |= tx_buf[1] << 8;
> +
> +	if (msg->tx_len > 2) {
> +		dev_err(dsi->dev, "too long tx buf length %zu for short write\n",
> +			msg->tx_len);
> +		return -EINVAL;
> +	}
> +
> +	val = GEN_HDATA(data) | GEN_HTYPE(msg->type);
> +	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
> +}
> +
> +static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
> +				      const struct mipi_dsi_msg *msg)
> +{
> +	const u8 *tx_buf = msg->tx_buf;
> +	int len = msg->tx_len, pld_data_bytes = sizeof(u32), ret;
> +	u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
> +	u32 remainder;
> +	u32 val;
> +
> +	if (msg->tx_len < 3) {
> +		dev_err(dsi->dev, "wrong tx buf length %zu for long write\n",
> +			msg->tx_len);
> +		return -EINVAL;
> +	}
> +
> +	while (DIV_ROUND_UP(len, pld_data_bytes)) {
> +		if (len < pld_data_bytes) {
> +			remainder = 0;
> +			memcpy(&remainder, tx_buf, len);
> +			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
> +			len = 0;
> +		} else {
> +			memcpy(&remainder, tx_buf, pld_data_bytes);
> +			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
> +			tx_buf += pld_data_bytes;
> +			len -= pld_data_bytes;
> +		}
> +
> +		ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
> +					 val, !(val & GEN_PLD_W_FULL), 1000,
> +					 CMD_PKT_STATUS_TIMEOUT_US);
> +		if (ret < 0) {
> +			dev_err(dsi->dev,
> +				"failed to get available write payload FIFO\n");
> +			return ret;
> +		}
> +	}
> +
> +	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, hdr_val);
> +}
> +
> +static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
> +					 const struct mipi_dsi_msg *msg)
> +{
> +	struct dw_mipi_dsi *dsi = host_to_dsi(host);
> +	int ret;
> +
> +	/*
> +	 * TODO dw drv improvements
> +	 * use mipi_dsi_create_packet() instead of all following
> +	 * functions and code (no switch cases, no
> +	 * dw_mipi_dsi_dcs_short_write(), only the loop in long_write...)
> +	 * and use packet.header...
> +	 */
> +	dw_mipi_message_config(dsi, msg);
> +
> +	switch (msg->type) {
> +	case MIPI_DSI_DCS_SHORT_WRITE:
> +	case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
> +	case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE:
> +		ret = dw_mipi_dsi_dcs_short_write(dsi, msg);
> +		break;
> +	case MIPI_DSI_DCS_LONG_WRITE:
> +		ret = dw_mipi_dsi_dcs_long_write(dsi, msg);
> +		break;
> +	default:
> +		dev_err(dsi->dev, "unsupported message type 0x%02x\n",
> +			msg->type);
> +		ret = -EINVAL;
> +	}
> +
> +	return ret;
> +}
> +
> +static const struct mipi_dsi_host_ops dw_mipi_dsi_host_ops = {
> +	.attach = dw_mipi_dsi_host_attach,
> +	.detach = dw_mipi_dsi_host_detach,
> +	.transfer = dw_mipi_dsi_host_transfer,
> +};
> +
> +static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi)
> +{
> +	u32 val;
> +
> +	/*
> +	 * TODO dw drv improvements
> +	 * enabling low power is panel-dependent, we should use the
> +	 * panel configuration here...
> +	 */
> +	val = ENABLE_LOW_POWER;
> +
> +	if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
> +		val |= VID_MODE_TYPE_BURST;
> +	else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
> +		val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES;
> +	else
> +		val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS;
> +
> +	dsi_write(dsi, DSI_VID_MODE_CFG, val);
> +}
> +
> +static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi,
> +				 unsigned long mode_flags)
> +{
> +	dsi_write(dsi, DSI_PWR_UP, RESET);
> +
> +	if (mode_flags & MIPI_DSI_MODE_VIDEO) {
> +		dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE);
> +		dw_mipi_dsi_video_mode_config(dsi);
> +		dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS);
> +	} else {
> +		dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
> +	}
> +
> +	dsi_write(dsi, DSI_PWR_UP, POWERUP);
> +}
> +
> +static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
> +{
> +	dsi_write(dsi, DSI_PWR_UP, RESET);
> +	dsi_write(dsi, DSI_PHY_RSTZ, PHY_RSTZ);
> +}
> +
> +static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
> +{
> +	/*
> +	 * The maximum permitted escape clock is 20MHz and it is derived from
> +	 * lanebyteclk, which is running at "lane_mbps / 8".  Thus we want:
> +	 *
> +	 *     (lane_mbps >> 3) / esc_clk_division < 20
> +	 * which is:
> +	 *     (lane_mbps >> 3) / 20 > esc_clk_division
> +	 */
> +	u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1;
> +
> +	dsi_write(dsi, DSI_PWR_UP, RESET);
> +
> +	/*
> +	 * TODO dw drv improvements
> +	 * timeout clock division should be computed with the
> +	 * high speed transmission counter timeout and byte lane...
> +	 */
> +	dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
> +		  TX_ESC_CLK_DIVIDSION(esc_clk_division));
> +}
> +
> +static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
> +				   struct drm_display_mode *mode)
> +{
> +	u32 val = 0, color = 0;
> +
> +	switch (dsi->format) {
> +	case MIPI_DSI_FMT_RGB888:
> +		color = DPI_COLOR_CODING_24BIT;
> +		break;
> +	case MIPI_DSI_FMT_RGB666:
> +		color = DPI_COLOR_CODING_18BIT_2 | EN18_LOOSELY;
> +		break;
> +	case MIPI_DSI_FMT_RGB666_PACKED:
> +		color = DPI_COLOR_CODING_18BIT_1;
> +		break;
> +	case MIPI_DSI_FMT_RGB565:
> +		color = DPI_COLOR_CODING_16BIT_1;
> +		break;
> +	}
> +
> +	if (mode->flags & DRM_MODE_FLAG_NVSYNC)
> +		val |= VSYNC_ACTIVE_LOW;
> +	if (mode->flags & DRM_MODE_FLAG_NHSYNC)
> +		val |= HSYNC_ACTIVE_LOW;
> +
> +	dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel));
> +	dsi_write(dsi, DSI_DPI_COLOR_CODING, color);
> +	dsi_write(dsi, DSI_DPI_CFG_POL, val);
> +	/*
> +	 * TODO dw drv improvements
> +	 * largest packet sizes during hfp or during vsa/vpb/vfp
> +	 * should be computed according to byte lane, lane number and only
> +	 * if sending lp cmds in high speed is enable (PHY_TXREQUESTCLKHS)
> +	 */
> +	dsi_write(dsi, DSI_DPI_LP_CMD_TIM, OUTVACT_LPCMD_TIME(4)
> +		  | INVACT_LPCMD_TIME(4));
> +}
> +
> +static void dw_mipi_dsi_packet_handler_config(struct dw_mipi_dsi *dsi)
> +{
> +	dsi_write(dsi, DSI_PCKHDL_CFG, EN_CRC_RX | EN_ECC_RX | EN_BTA);
> +}
> +
> +static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi,
> +					    struct drm_display_mode *mode)
> +{
> +	/*
> +	 * TODO dw drv improvements
> +	 * only burst mode is supported here. For non-burst video modes,
> +	 * we should compute DSI_VID_PKT_SIZE, DSI_VCCR.NUMC &
> +	 * DSI_VNPCR.NPSIZE... especially because this driver supports
> +	 * non-burst video modes, see dw_mipi_dsi_video_mode_config()...
> +	 */
> +	dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay));
> +}
> +
> +static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
> +{
> +	/*
> +	 * TODO dw drv improvements
> +	 * compute high speed transmission counter timeout according
> +	 * to the timeout clock division (TO_CLK_DIVIDSION) and byte lane...
> +	 */
> +	dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000));
> +	/*
> +	 * TODO dw drv improvements
> +	 * the Bus-Turn-Around Timeout Counter should be computed
> +	 * according to byte lane...
> +	 */
> +	dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00);
> +	dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
> +}
> +
> +/* Get lane byte clock cycles. */
> +static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi,
> +					   struct drm_display_mode *mode,
> +					   u32 hcomponent)
> +{
> +	u32 frac, lbcc;
> +
> +	lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8;
> +
> +	frac = lbcc % mode->clock;
> +	lbcc = lbcc / mode->clock;
> +	if (frac)
> +		lbcc++;
> +
> +	return lbcc;
> +}
> +
> +static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi,
> +					  struct drm_display_mode *mode)
> +{
> +	u32 htotal, hsa, hbp, lbcc;
> +
> +	htotal = mode->htotal;
> +	hsa = mode->hsync_end - mode->hsync_start;
> +	hbp = mode->htotal - mode->hsync_end;
> +
> +	/*
> +	 * TODO dw drv improvements
> +	 * computations below may be improved...
> +	 */
> +	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, htotal);
> +	dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc);
> +
> +	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hsa);
> +	dsi_write(dsi, DSI_VID_HSA_TIME, lbcc);
> +
> +	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hbp);
> +	dsi_write(dsi, DSI_VID_HBP_TIME, lbcc);
> +}
> +
> +static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi,
> +					       struct drm_display_mode *mode)
> +{
> +	u32 vactive, vsa, vfp, vbp;
> +
> +	vactive = mode->vdisplay;
> +	vsa = mode->vsync_end - mode->vsync_start;
> +	vfp = mode->vsync_start - mode->vdisplay;
> +	vbp = mode->vtotal - mode->vsync_end;
> +
> +	dsi_write(dsi, DSI_VID_VACTIVE_LINES, vactive);
> +	dsi_write(dsi, DSI_VID_VSA_LINES, vsa);
> +	dsi_write(dsi, DSI_VID_VFP_LINES, vfp);
> +	dsi_write(dsi, DSI_VID_VBP_LINES, vbp);
> +}
> +
> +static void dw_mipi_dsi_dphy_timing_config(struct dw_mipi_dsi *dsi)
> +{
> +	/*
> +	 * TODO dw drv improvements
> +	 * data & clock lane timers should be computed according to panel
> +	 * blankings and to the automatic clock lane control mode...
> +	 * note: DSI_PHY_TMR_CFG.MAX_RD_TIME should be in line with
> +	 * DSI_CMD_MODE_CFG.MAX_RD_PKT_SIZE_LP (see CMD_MODE_ALL_LP)
> +	 */
> +	dsi_write(dsi, DSI_PHY_TMR_CFG, PHY_HS2LP_TIME(0x40)
> +		  | PHY_LP2HS_TIME(0x40) | MAX_RD_TIME(10000));
> +
> +	dsi_write(dsi, DSI_PHY_TMR_LPCLK_CFG, PHY_CLKHS2LP_TIME(0x40)
> +		  | PHY_CLKLP2HS_TIME(0x40));
> +}
> +
> +static void dw_mipi_dsi_dphy_interface_config(struct dw_mipi_dsi *dsi)
> +{
> +	/*
> +	 * TODO dw drv improvements
> +	 * stop wait time should be the maximum between host dsi
> +	 * and panel stop wait times
> +	 */
> +	dsi_write(dsi, DSI_PHY_IF_CFG, PHY_STOP_WAIT_TIME(0x20) |
> +		  N_LANES(dsi->lanes));
> +}
> +
> +static void dw_mipi_dsi_dphy_init(struct dw_mipi_dsi *dsi)
> +{
> +	/* Clear PHY state */
> +	dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
> +		  | PHY_RSTZ | PHY_SHUTDOWNZ);
> +	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
> +	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR);
> +	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
> +}
> +
> +static void dw_mipi_dsi_dphy_enable(struct dw_mipi_dsi *dsi)
> +{
> +	u32 val;
> +	int ret;
> +
> +	dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |
> +		  PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
> +
> +	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
> +				 val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US);
> +	if (ret < 0)
> +		DRM_DEBUG_DRIVER("failed to wait phy lock state\n");
> +
> +	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
> +				 val, val & STOP_STATE_CLK_LANE, 1000,
> +				 PHY_STATUS_TIMEOUT_US);
> +	if (ret < 0)
> +		DRM_DEBUG_DRIVER("failed to wait phy clk lane stop state\n");
> +}
> +
> +static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi)
> +{
> +	dsi_read(dsi, DSI_INT_ST0);
> +	dsi_read(dsi, DSI_INT_ST1);
> +	dsi_write(dsi, DSI_INT_MSK0, 0);
> +	dsi_write(dsi, DSI_INT_MSK1, 0);
> +}
> +
> +static void dw_mipi_dsi_bridge_disable(struct drm_bridge *bridge)
> +{
> +	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
> +
> +	if (dsi->dpms_mode != DRM_MODE_DPMS_ON)
> +		return;
> +
> +	if (clk_enable(dsi->pclk)) {
> +		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
> +		return;
> +	}
> +
> +	drm_panel_disable(dsi->panel);
> +
> +	/* Switch to dsi command mode for the panel de-initialization */
> +	dw_mipi_dsi_set_mode(dsi, 0);
> +	drm_panel_unprepare(dsi->panel);
> +
> +	dw_mipi_dsi_disable(dsi);
> +	pm_runtime_put(dsi->dev);
> +	clk_disable(dsi->pclk);
> +	dsi->dpms_mode = DRM_MODE_DPMS_OFF;
> +}
> +
> +static void dw_mipi_dsi_bridge_enable(struct drm_bridge *bridge)
> +{
> +	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
> +	struct drm_encoder *encoder = bridge->encoder;
> +	struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
> +	const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
> +	void *priv_data = dsi->plat_data->priv_data;
> +	int ret;
> +
> +	if (dsi->dpms_mode == DRM_MODE_DPMS_ON)
> +		return;
> +
> +	if (clk_enable(dsi->pclk)) {
> +		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
> +		return;
> +	}
> +
> +	ret = phy_ops->get_lane_mbps(priv_data, mode, dsi->mode_flags,
> +				     dsi->lanes, dsi->format, &dsi->lane_mbps);
> +	if (ret)
> +		DRM_DEBUG_DRIVER("Phy get_lane_mbps() failed\n");
> +
> +	pm_runtime_get_sync(dsi->dev);
> +	dw_mipi_dsi_init(dsi);
> +	dw_mipi_dsi_dpi_config(dsi, mode);
> +	dw_mipi_dsi_packet_handler_config(dsi);
> +	dw_mipi_dsi_video_mode_config(dsi);
> +	dw_mipi_dsi_video_packet_config(dsi, mode);
> +	dw_mipi_dsi_command_mode_config(dsi);
> +	dw_mipi_dsi_line_timer_config(dsi, mode);
> +	dw_mipi_dsi_vertical_timing_config(dsi, mode);
> +
> +	dw_mipi_dsi_dphy_init(dsi);
> +	dw_mipi_dsi_dphy_timing_config(dsi);
> +	dw_mipi_dsi_dphy_interface_config(dsi);
> +
> +	dw_mipi_dsi_clear_err(dsi);
> +
> +	ret = phy_ops->init(priv_data);
> +	if (ret)
> +		DRM_DEBUG_DRIVER("Phy init() failed\n");
> +
> +	dw_mipi_dsi_dphy_enable(dsi);
> +
> +	dw_mipi_dsi_wait_for_two_frames(mode);
> +
> +	/* Switch to dsi command mode for the panel initialization */
> +	dw_mipi_dsi_set_mode(dsi, 0);
> +	if (drm_panel_prepare(dsi->panel))
> +		dev_err(dsi->dev, "failed to prepare panel\n");
> +
> +	/* Switch to dsi video mode to send image data to the panel */
> +	dw_mipi_dsi_set_mode(dsi, MIPI_DSI_MODE_VIDEO);
> +	drm_panel_enable(dsi->panel);
> +
> +	clk_disable(dsi->pclk);
> +
> +	dsi->dpms_mode = DRM_MODE_DPMS_ON;
> +}
> +
> +static int dw_mipi_dsi_connector_get_modes(struct drm_connector *connector)
> +{
> +	struct dw_mipi_dsi *dsi = con_to_dsi(connector);
> +
> +	return drm_panel_get_modes(dsi->panel);
> +}
> +
> +static enum drm_mode_status
> +dw_mipi_dsi_mode_valid(struct drm_connector *connector,
> +		       struct drm_display_mode *mode)
> +{
> +	struct dw_mipi_dsi *dsi = con_to_dsi(connector);
> +	const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data;
> +	enum drm_mode_status mode_status = MODE_OK;
> +
> +	if (pdata->mode_valid)
> +		mode_status = pdata->mode_valid(pdata->priv_data,
> +						connector, mode);
> +
> +	return mode_status;
> +}
> +
> +static struct drm_connector_helper_funcs dw_mipi_dsi_connector_helper_funcs = {
> +	.get_modes = dw_mipi_dsi_connector_get_modes,
> +	.mode_valid = dw_mipi_dsi_mode_valid,
> +};
> +
> +static void dw_mipi_dsi_drm_connector_destroy(struct drm_connector *connector)
> +{
> +	drm_connector_unregister(connector);
> +	drm_connector_cleanup(connector);
> +}
> +
> +static const struct drm_connector_funcs dw_mipi_dsi_atomic_connector_funcs = {
> +	.dpms = drm_atomic_helper_connector_dpms,
> +	.fill_modes = drm_helper_probe_single_connector_modes,
> +	.destroy = dw_mipi_dsi_drm_connector_destroy,
> +	.reset = drm_atomic_helper_connector_reset,
> +	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> +	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> +};
> +
> +static int dw_mipi_dsi_bridge_attach(struct drm_bridge *bridge)
> +{
> +	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
> +	struct drm_connector *connector = &dsi->connector;
> +
> +	if (!bridge->encoder) {
> +		DRM_ERROR("Parent encoder object not found\n");
> +		return -ENODEV;
> +	}
> +
> +	/* Set the encoder type as caller does not know it */
> +	bridge->encoder->encoder_type = DRM_MODE_ENCODER_DSI;
> +
> +	connector->polled = DRM_CONNECTOR_POLL_HPD;
> +
> +	drm_connector_helper_add(connector,
> +				 &dw_mipi_dsi_connector_helper_funcs);
> +
> +	drm_connector_init(bridge->dev, connector,
> +			   &dw_mipi_dsi_atomic_connector_funcs,
> +			   DRM_MODE_CONNECTOR_DSI);
> +
> +	drm_mode_connector_attach_encoder(connector, bridge->encoder);
> +
> +	return 0;
> +}
> +
> +static struct drm_bridge_funcs dw_mipi_dsi_bridge_funcs = {
> +	.enable = dw_mipi_dsi_bridge_enable,
> +	.disable = dw_mipi_dsi_bridge_disable,
> +	.attach = dw_mipi_dsi_bridge_attach,
> +};
> +
> +static struct dw_mipi_dsi *
> +__dw_mipi_dsi_probe(struct platform_device *pdev,
> +		    const struct dw_mipi_dsi_plat_data *plat_data)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct reset_control *apb_rst;
> +	struct dw_mipi_dsi *dsi;
> +	struct resource *res;
> +	int ret;
> +
> +	dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
> +	if (!dsi)
> +		return ERR_PTR(-ENOMEM);
> +
> +	dsi->dev = dev;
> +	dsi->plat_data = plat_data;
> +	dsi->dpms_mode = DRM_MODE_DPMS_OFF;
> +
> +	if (!plat_data->phy_ops->init || !plat_data->phy_ops->get_lane_mbps) {
> +		DRM_ERROR("Phy not properly configured\n");
> +		return ERR_PTR(-ENODEV);
> +	}
> +
> +	if (!plat_data->base) {
> +		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +		if (!res)
> +			return ERR_PTR(-ENODEV);
> +
> +		dsi->base = devm_ioremap_resource(dev, res);
> +		if (IS_ERR(dsi->base))
> +			return ERR_PTR(-ENODEV);
> +
> +	} else {
> +		dsi->base = plat_data->base;
> +	}
> +
> +	dsi->pclk = devm_clk_get(dev, "pclk");
> +	if (IS_ERR(dsi->pclk)) {
> +		ret = PTR_ERR(dsi->pclk);
> +		dev_err(dev, "Unable to get pclk: %d\n", ret);
> +		return ERR_PTR(ret);
> +	}
> +
> +	/*
> +	 * Note that the reset was not defined in the initial device tree, so
> +	 * we have to be prepared for it not being found.
> +	 */
> +	apb_rst = devm_reset_control_get(dev, "apb");
> +	if (IS_ERR(apb_rst)) {
> +		ret = PTR_ERR(apb_rst);
> +		if (ret == -ENOENT) {
> +			apb_rst = NULL;
> +		} else {
> +			dev_err(dev, "Unable to get reset control: %d\n", ret);
> +			return ERR_PTR(ret);
> +		}
> +	}
> +
> +	if (apb_rst) {
> +		ret = clk_prepare_enable(dsi->pclk);
> +		if (ret) {
> +			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
> +			return ERR_PTR(ret);
> +		}
> +
> +		reset_control_assert(apb_rst);
> +		usleep_range(10, 20);
> +		reset_control_deassert(apb_rst);
> +
> +		clk_disable(dsi->pclk);
> +	}
> +
> +	pm_runtime_enable(dev);
> +
> +	dsi->dsi_host.ops = &dw_mipi_dsi_host_ops;
> +	dsi->dsi_host.dev = dev;
> +	ret = mipi_dsi_host_register(&dsi->dsi_host);
> +	if (ret) {
> +		dev_err(dev, "Failed to register MIPI host: %d\n", ret);
> +		return ERR_PTR(ret);
> +	}
> +
> +	dsi->bridge.driver_private = dsi;
> +	dsi->bridge.funcs = &dw_mipi_dsi_bridge_funcs;
> +#ifdef CONFIG_OF
> +	dsi->bridge.of_node = pdev->dev.of_node;
> +#endif
> +
> +	clk_enable(dsi->pclk);
> +
> +	dev_set_drvdata(dev, dsi);
> +
> +	return dsi;
> +}
> +
> +static void __dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi)
> +{
> +	pm_runtime_disable(dsi->dev);
> +}
> +
> +/*
> + * Probe/remove API, used from platforms based on the DRM bridge API.
> + */
> +int dw_mipi_dsi_probe(struct platform_device *pdev,
> +		      const struct dw_mipi_dsi_plat_data *plat_data)
> +{
> +	struct dw_mipi_dsi *dsi;
> +	int ret;
> +
> +	dsi = __dw_mipi_dsi_probe(pdev, plat_data);
> +	if (IS_ERR(dsi))
> +		return PTR_ERR(dsi);
> +
> +	ret = drm_bridge_add(&dsi->bridge);
> +	if (ret < 0) {
> +		__dw_mipi_dsi_remove(dsi);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi_probe);
> +
> +void dw_mipi_dsi_remove(struct platform_device *pdev)
> +{
> +	struct dw_mipi_dsi *dsi = platform_get_drvdata(pdev);
> +
> +	mipi_dsi_host_unregister(&dsi->dsi_host);
> +	drm_bridge_remove(&dsi->bridge);
> +
> +	__dw_mipi_dsi_remove(dsi);
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi_remove);
> +
> +/*
> + * Bind/unbind API, used from platforms based on the component framework.
> + */
> +int dw_mipi_dsi_bind(struct platform_device *pdev, struct drm_encoder *encoder,
> +		     const struct dw_mipi_dsi_plat_data *plat_data)
> +{
> +	struct dw_mipi_dsi *dsi;
> +	int ret;
> +
> +	dsi = __dw_mipi_dsi_probe(pdev, plat_data);
> +	if (IS_ERR(dsi))
> +		return PTR_ERR(dsi);
> +
> +	ret = drm_bridge_attach(encoder, &dsi->bridge, NULL);
> +	if (ret) {
> +		dw_mipi_dsi_remove(pdev);
> +		DRM_ERROR("Failed to initialize bridge with drm\n");
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi_bind);
> +
> +void dw_mipi_dsi_unbind(struct device *dev)
> +{
> +	struct dw_mipi_dsi *dsi = dev_get_drvdata(dev);
> +
> +	__dw_mipi_dsi_remove(dsi);
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi_unbind);
> +
> +MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
> +MODULE_AUTHOR("Philippe Cornu <philippe.cornu@st.com>");
> +MODULE_DESCRIPTION("DW MIPI DSI host controller driver");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("platform:dw-mipi-dsi");
> diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h
> new file mode 100644
> index 0000000..2043a37
> --- /dev/null
> +++ b/include/drm/bridge/dw_mipi_dsi.h
> @@ -0,0 +1,42 @@
> +/*
> + * Copyright (C) STMicroelectronics SA 2017
> + *
> + * Authors: Philippe Cornu <philippe.cornu@st.com>
> + *          Yannick Fertre <yannick.fertre@st.com>
> + *
> + * License terms:  GNU General Public License (GPL), version 2
> + */
> +
> +#ifndef __DW_MIPI_DSI__
> +#define __DW_MIPI_DSI__
> +
> +#include <drm/drmP.h>
> +
> +struct dw_mipi_dsi_phy_ops {
> +	int (*init)(void *priv_data);
> +	int (*get_lane_mbps)(void *priv_data, struct drm_display_mode *mode,
> +			     unsigned long mode_flags, u32 lanes, u32 format,
> +			     unsigned int *lane_mbps);
> +};
> +
> +struct dw_mipi_dsi_plat_data {
> +	void __iomem *base;
> +	unsigned int max_data_lanes;
> +
> +	enum drm_mode_status (*mode_valid)(void *priv_data,
> +					   struct drm_connector *connector,
> +					   struct drm_display_mode *mode);
> +
> +	const struct dw_mipi_dsi_phy_ops *phy_ops;
> +
> +	void *priv_data;
> +};
> +
> +int dw_mipi_dsi_probe(struct platform_device *pdev,
> +		      const struct dw_mipi_dsi_plat_data *plat_data);
> +void dw_mipi_dsi_remove(struct platform_device *pdev);
> +int dw_mipi_dsi_bind(struct platform_device *pdev, struct drm_encoder *encoder,
> +		     const struct dw_mipi_dsi_plat_data *plat_data);
> +void dw_mipi_dsi_unbind(struct device *dev);
> +
> +#endif /* __DW_MIPI_DSI__ */
>
Archit Taneja June 9, 2017, 5:21 a.m. UTC | #2
Hi Phillipe,

Thanks for the clean ups. Some comments inline.

On 06/02/2017 08:07 PM, Philippe CORNU wrote:
> Add a Synopsys Designware MIPI DSI host DRM bridge driver, based on the
> Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.
> 
> Signed-off-by: Philippe CORNU <philippe.cornu@st.com>
> ---
>   drivers/gpu/drm/bridge/synopsys/Kconfig       |    9 +
>   drivers/gpu/drm/bridge/synopsys/Makefile      |    2 +
>   drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 1022 +++++++++++++++++++++++++
>   include/drm/bridge/dw_mipi_dsi.h              |   42 +
>   4 files changed, 1075 insertions(+)
>   create mode 100644 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
>   create mode 100644 include/drm/bridge/dw_mipi_dsi.h
> 
> diff --git a/drivers/gpu/drm/bridge/synopsys/Kconfig b/drivers/gpu/drm/bridge/synopsys/Kconfig
> index 40d2827..d7fbdff 100644
> --- a/drivers/gpu/drm/bridge/synopsys/Kconfig
> +++ b/drivers/gpu/drm/bridge/synopsys/Kconfig
> @@ -21,3 +21,12 @@ config DRM_DW_HDMI_I2S_AUDIO
>   	help
>   	  Support the I2S Audio interface which is part of the Synopsys
>   	  Designware HDMI block.
> +
> +config DRM_DW_MIPI_DSI
> +	tristate "Synopsys DesignWare MIPI DSI host controller bridge"
> +	select DRM_KMS_HELPER
> +	select DRM_MIPI_DSI
> +	select DRM_PANEL
> +	help
> +	  Choose this if you want to use the Synopsys DesignWare MIPI DSI host
> +	  controller bridge.

I was looking at the DW_HDMI entry, it doesn't have the 'help' entry or the description
entry. I'm not sure whether it was done intentionally or not, but it avoids DW_HDMI being
visible in menuconfig. That's convenient because we don't really want to build DW_MIPI_DSI
if no KMS driver is using it. You could consider dropping these too, unless someone comments
here suggesting a better way.


> diff --git a/drivers/gpu/drm/bridge/synopsys/Makefile b/drivers/gpu/drm/bridge/synopsys/Makefile
> index 17aa7a6..5f57d36 100644
> --- a/drivers/gpu/drm/bridge/synopsys/Makefile
> +++ b/drivers/gpu/drm/bridge/synopsys/Makefile
> @@ -3,3 +3,5 @@
>   obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
>   obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
>   obj-$(CONFIG_DRM_DW_HDMI_I2S_AUDIO) += dw-hdmi-i2s-audio.o
> +
> +obj-$(CONFIG_DRM_DW_MIPI_DSI) += dw-mipi-dsi.o
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
> new file mode 100644
> index 0000000..6b25629
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
> @@ -0,0 +1,1022 @@
> +/*
> + * Copyright (c) 2016, Fuzhou Rockchip Electronics Co., Ltd
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * Modified by Philippe Cornu <philippe.cornu@st.com>
> + * This generic Synopsys Designware MIPI DSI host driver is based on the
> + * Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.

It would be good to add your copyright too

> + */
> +
> +#include <linux/clk.h>
> +#include <linux/component.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/reset.h>
> +#include <drm/drmP.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_crtc.h>
> +#include <drm/drm_crtc_helper.h>
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_of.h>

I'm not sure if the above header is used^

> +#include <drm/drm_panel.h>
> +#include <drm/bridge/dw_mipi_dsi.h>
> +#include <video/mipi_display.h>
> +
> +#define DSI_VERSION			0x00
> +#define DSI_PWR_UP			0x04
> +#define RESET				0
> +#define POWERUP				BIT(0)
> +
> +#define DSI_CLKMGR_CFG			0x08
> +#define TO_CLK_DIVIDSION(div)		(((div) & 0xff) << 8)
> +#define TX_ESC_CLK_DIVIDSION(div)	(((div) & 0xff) << 0)
> +
> +#define DSI_DPI_VCID			0x0c
> +#define DPI_VID(vid)			(((vid) & 0x3) << 0)
> +
> +#define DSI_DPI_COLOR_CODING		0x10
> +#define EN18_LOOSELY			BIT(8)
> +#define DPI_COLOR_CODING_16BIT_1	0x0
> +#define DPI_COLOR_CODING_16BIT_2	0x1
> +#define DPI_COLOR_CODING_16BIT_3	0x2
> +#define DPI_COLOR_CODING_18BIT_1	0x3
> +#define DPI_COLOR_CODING_18BIT_2	0x4
> +#define DPI_COLOR_CODING_24BIT		0x5
> +
> +#define DSI_DPI_CFG_POL			0x14
> +#define COLORM_ACTIVE_LOW		BIT(4)
> +#define SHUTD_ACTIVE_LOW		BIT(3)
> +#define HSYNC_ACTIVE_LOW		BIT(2)
> +#define VSYNC_ACTIVE_LOW		BIT(1)
> +#define DATAEN_ACTIVE_LOW		BIT(0)
> +
> +#define DSI_DPI_LP_CMD_TIM		0x18
> +#define OUTVACT_LPCMD_TIME(p)		(((p) & 0xff) << 16)
> +#define INVACT_LPCMD_TIME(p)		((p) & 0xff)
> +
> +#define DSI_DBI_CFG			0x20
> +#define DSI_DBI_CMDSIZE			0x28
> +
> +#define DSI_PCKHDL_CFG			0x2c
> +#define EN_CRC_RX			BIT(4)
> +#define EN_ECC_RX			BIT(3)
> +#define EN_BTA				BIT(2)
> +#define EN_EOTP_RX			BIT(1)
> +#define EN_EOTP_TX			BIT(0)
> +
> +#define DSI_MODE_CFG			0x34
> +#define ENABLE_VIDEO_MODE		0
> +#define ENABLE_CMD_MODE			BIT(0)
> +
> +#define DSI_VID_MODE_CFG		0x38
> +#define FRAME_BTA_ACK			BIT(14)
> +#define ENABLE_LOW_POWER		(0x3f << 8)
> +#define ENABLE_LOW_POWER_MASK		(0x3f << 8)
> +#define VID_MODE_TYPE_NON_BURST_SYNC_PULSES	0x0
> +#define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS	0x1
> +#define VID_MODE_TYPE_BURST			0x2
> +#define VID_MODE_TYPE_MASK			0x3
> +
> +#define DSI_VID_PKT_SIZE		0x3c
> +#define VID_PKT_SIZE(p)			(((p) & 0x3fff) << 0)
> +#define VID_PKT_MAX_SIZE		0x3fff
> +
> +#define DSI_VID_HSA_TIME		0x48
> +#define DSI_VID_HBP_TIME		0x4c
> +#define DSI_VID_HLINE_TIME		0x50
> +#define DSI_VID_VSA_LINES		0x54
> +#define DSI_VID_VBP_LINES		0x58
> +#define DSI_VID_VFP_LINES		0x5c
> +#define DSI_VID_VACTIVE_LINES		0x60
> +#define DSI_CMD_MODE_CFG		0x68
> +#define MAX_RD_PKT_SIZE_LP		BIT(24)
> +#define DCS_LW_TX_LP			BIT(19)
> +#define DCS_SR_0P_TX_LP			BIT(18)
> +#define DCS_SW_1P_TX_LP			BIT(17)
> +#define DCS_SW_0P_TX_LP			BIT(16)
> +#define GEN_LW_TX_LP			BIT(14)
> +#define GEN_SR_2P_TX_LP			BIT(13)
> +#define GEN_SR_1P_TX_LP			BIT(12)
> +#define GEN_SR_0P_TX_LP			BIT(11)
> +#define GEN_SW_2P_TX_LP			BIT(10)
> +#define GEN_SW_1P_TX_LP			BIT(9)
> +#define GEN_SW_0P_TX_LP			BIT(8)
> +#define EN_ACK_RQST			BIT(1)
> +#define EN_TEAR_FX			BIT(0)
> +
> +#define CMD_MODE_ALL_LP			(MAX_RD_PKT_SIZE_LP | \
> +					 DCS_LW_TX_LP | \
> +					 DCS_SR_0P_TX_LP | \
> +					 DCS_SW_1P_TX_LP | \
> +					 DCS_SW_0P_TX_LP | \
> +					 GEN_LW_TX_LP | \
> +					 GEN_SR_2P_TX_LP | \
> +					 GEN_SR_1P_TX_LP | \
> +					 GEN_SR_0P_TX_LP | \
> +					 GEN_SW_2P_TX_LP | \
> +					 GEN_SW_1P_TX_LP | \
> +					 GEN_SW_0P_TX_LP)
> +
> +#define DSI_GEN_HDR			0x6c
> +#define GEN_HDATA(data)			(((data) & 0xffff) << 8)
> +#define GEN_HDATA_MASK			(0xffff << 8)
> +#define GEN_HTYPE(type)			(((type) & 0xff) << 0)
> +#define GEN_HTYPE_MASK			0xff
> +
> +#define DSI_GEN_PLD_DATA		0x70
> +
> +#define DSI_CMD_PKT_STATUS		0x74
> +#define GEN_CMD_EMPTY			BIT(0)
> +#define GEN_CMD_FULL			BIT(1)
> +#define GEN_PLD_W_EMPTY			BIT(2)
> +#define GEN_PLD_W_FULL			BIT(3)
> +#define GEN_PLD_R_EMPTY			BIT(4)
> +#define GEN_PLD_R_FULL			BIT(5)
> +#define GEN_RD_CMD_BUSY			BIT(6)
> +
> +#define DSI_TO_CNT_CFG			0x78
> +#define HSTX_TO_CNT(p)			(((p) & 0xffff) << 16)
> +#define LPRX_TO_CNT(p)			((p) & 0xffff)
> +
> +#define DSI_BTA_TO_CNT			0x8c
> +#define DSI_LPCLK_CTRL			0x94
> +#define AUTO_CLKLANE_CTRL		BIT(1)
> +#define PHY_TXREQUESTCLKHS		BIT(0)
> +
> +#define DSI_PHY_TMR_LPCLK_CFG		0x98
> +#define PHY_CLKHS2LP_TIME(lbcc)		(((lbcc) & 0x3ff) << 16)
> +#define PHY_CLKLP2HS_TIME(lbcc)		((lbcc) & 0x3ff)
> +
> +#define DSI_PHY_TMR_CFG			0x9c
> +#define PHY_HS2LP_TIME(lbcc)		(((lbcc) & 0xff) << 24)
> +#define PHY_LP2HS_TIME(lbcc)		(((lbcc) & 0xff) << 16)
> +#define MAX_RD_TIME(lbcc)		((lbcc) & 0x7fff)
> +
> +#define DSI_PHY_RSTZ			0xa0
> +#define PHY_DISFORCEPLL			0
> +#define PHY_ENFORCEPLL			BIT(3)
> +#define PHY_DISABLECLK			0
> +#define PHY_ENABLECLK			BIT(2)
> +#define PHY_RSTZ			0
> +#define PHY_UNRSTZ			BIT(1)
> +#define PHY_SHUTDOWNZ			0
> +#define PHY_UNSHUTDOWNZ			BIT(0)
> +
> +#define DSI_PHY_IF_CFG			0xa4
> +#define N_LANES(n)			((((n) - 1) & 0x3) << 0)
> +#define PHY_STOP_WAIT_TIME(cycle)	(((cycle) & 0xff) << 8)
> +
> +#define DSI_PHY_STATUS			0xb0
> +#define LOCK				BIT(0)
> +#define STOP_STATE_CLK_LANE		BIT(2)
> +
> +#define DSI_PHY_TST_CTRL0		0xb4
> +#define PHY_TESTCLK			BIT(1)
> +#define PHY_UNTESTCLK			0
> +#define PHY_TESTCLR			BIT(0)
> +#define PHY_UNTESTCLR			0
> +
> +#define DSI_PHY_TST_CTRL1		0xb8
> +#define PHY_TESTEN			BIT(16)
> +#define PHY_UNTESTEN			0
> +#define PHY_TESTDOUT(n)			(((n) & 0xff) << 8)
> +#define PHY_TESTDIN(n)			(((n) & 0xff) << 0)
> +
> +#define DSI_INT_ST0			0xbc
> +#define DSI_INT_ST1			0xc0
> +#define DSI_INT_MSK0			0xc4
> +#define DSI_INT_MSK1			0xc8
> +
> +#define PHY_STATUS_TIMEOUT_US		10000
> +#define CMD_PKT_STATUS_TIMEOUT_US	20000
> +
> +struct dw_mipi_dsi {
> +	struct drm_bridge bridge;
> +	struct drm_connector connector;
> +	struct mipi_dsi_host dsi_host;
> +	struct drm_panel *panel;
> +	struct device *dev;
> +	void __iomem *base;
> +
> +	struct clk *pclk;
> +
> +	int dpms_mode;
> +	unsigned int lane_mbps; /* per lane */
> +	u32 channel;
> +	u32 lanes;
> +	u32 format;
> +	unsigned long mode_flags;
> +
> +	const struct dw_mipi_dsi_plat_data *plat_data;
> +};
> +
> +/*
> + * The controller should generate 2 frames before
> + * preparing the peripheral.
> + */
> +static void dw_mipi_dsi_wait_for_two_frames(struct drm_display_mode *mode)
> +{
> +	int refresh, two_frames;
> +
> +	refresh = drm_mode_vrefresh(mode);
> +	two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2;
> +	msleep(two_frames);
> +}
> +
> +static inline struct dw_mipi_dsi *host_to_dsi(struct mipi_dsi_host *host)
> +{
> +	return container_of(host, struct dw_mipi_dsi, dsi_host);
> +}
> +
> +static inline struct dw_mipi_dsi *con_to_dsi(struct drm_connector *con)
> +{
> +	return container_of(con, struct dw_mipi_dsi, connector);
> +}
> +
> +static inline struct dw_mipi_dsi *bridge_to_dsi(struct drm_bridge *bridge)
> +{
> +	return container_of(bridge, struct dw_mipi_dsi, bridge);
> +}
> +
> +static inline void dsi_write(struct dw_mipi_dsi *dsi, u32 reg, u32 val)
> +{
> +	writel_relaxed(val, dsi->base + reg);
> +}
> +
> +static inline u32 dsi_read(struct dw_mipi_dsi *dsi, u32 reg)
> +{
> +	return readl_relaxed(dsi->base + reg);
> +}
> +
> +static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
> +				   struct mipi_dsi_device *device)
> +{
> +	struct dw_mipi_dsi *dsi = host_to_dsi(host);
> +
> +	if (device->lanes > dsi->plat_data->max_data_lanes) {
> +		dev_err(dsi->dev, "the number of data lanes(%u) is too many\n",
> +			device->lanes);
> +		return -EINVAL;
> +	}
> +
> +	dsi->lanes = device->lanes;
> +	dsi->channel = device->channel;
> +	dsi->format = device->format;
> +	dsi->mode_flags = device->mode_flags;
> +	dsi->panel = of_drm_find_panel(device->dev.of_node);
> +	if (dsi->panel)
> +		return drm_panel_attach(dsi->panel, &dsi->connector);
> +
> +	return -EINVAL;
> +}
> +
> +static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
> +				   struct mipi_dsi_device *device)
> +{
> +	struct dw_mipi_dsi *dsi = host_to_dsi(host);
> +
> +	drm_panel_detach(dsi->panel);
> +
> +	return 0;
> +}
> +
> +static void dw_mipi_message_config(struct dw_mipi_dsi *dsi,
> +				   const struct mipi_dsi_msg *msg)
> +{
> +	bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM;
> +	u32 val = 0;
> +
> +	if (msg->flags & MIPI_DSI_MSG_REQ_ACK)
> +		val |= EN_ACK_RQST;
> +	if (lpm)
> +		val |= CMD_MODE_ALL_LP;
> +
> +	dsi_write(dsi, DSI_LPCLK_CTRL, lpm ? 0 : PHY_TXREQUESTCLKHS);
> +	dsi_write(dsi, DSI_CMD_MODE_CFG, val);
> +}
> +
> +static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
> +{
> +	int ret;
> +	u32 val, mask;
> +
> +	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
> +				 val, !(val & GEN_CMD_FULL), 1000,
> +				 CMD_PKT_STATUS_TIMEOUT_US);
> +	if (ret < 0) {
> +		dev_err(dsi->dev, "failed to get available command FIFO\n");
> +		return ret;
> +	}
> +
> +	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
> +
> +	mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
> +	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
> +				 val, (val & mask) == mask,
> +				 1000, CMD_PKT_STATUS_TIMEOUT_US);
> +	if (ret < 0) {
> +		dev_err(dsi->dev, "failed to write command FIFO\n");
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
> +				       const struct mipi_dsi_msg *msg)
> +{
> +	const u8 *tx_buf = msg->tx_buf;
> +	u16 data = 0;
> +	u32 val;
> +
> +	if (msg->tx_len > 0)
> +		data |= tx_buf[0];
> +	if (msg->tx_len > 1)
> +		data |= tx_buf[1] << 8;
> +
> +	if (msg->tx_len > 2) {
> +		dev_err(dsi->dev, "too long tx buf length %zu for short write\n",
> +			msg->tx_len);
> +		return -EINVAL;
> +	}
> +
> +	val = GEN_HDATA(data) | GEN_HTYPE(msg->type);
> +	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
> +}
> +
> +static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
> +				      const struct mipi_dsi_msg *msg)
> +{
> +	const u8 *tx_buf = msg->tx_buf;
> +	int len = msg->tx_len, pld_data_bytes = sizeof(u32), ret;
> +	u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
> +	u32 remainder;
> +	u32 val;
> +
> +	if (msg->tx_len < 3) {
> +		dev_err(dsi->dev, "wrong tx buf length %zu for long write\n",
> +			msg->tx_len);
> +		return -EINVAL;
> +	}
> +
> +	while (DIV_ROUND_UP(len, pld_data_bytes)) {
> +		if (len < pld_data_bytes) {
> +			remainder = 0;
> +			memcpy(&remainder, tx_buf, len);
> +			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
> +			len = 0;
> +		} else {
> +			memcpy(&remainder, tx_buf, pld_data_bytes);
> +			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
> +			tx_buf += pld_data_bytes;
> +			len -= pld_data_bytes;
> +		}
> +
> +		ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
> +					 val, !(val & GEN_PLD_W_FULL), 1000,
> +					 CMD_PKT_STATUS_TIMEOUT_US);
> +		if (ret < 0) {
> +			dev_err(dsi->dev,
> +				"failed to get available write payload FIFO\n");
> +			return ret;
> +		}
> +	}
> +
> +	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, hdr_val);
> +}
> +
> +static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
> +					 const struct mipi_dsi_msg *msg)
> +{
> +	struct dw_mipi_dsi *dsi = host_to_dsi(host);
> +	int ret;
> +
> +	/*
> +	 * TODO dw drv improvements
> +	 * use mipi_dsi_create_packet() instead of all following
> +	 * functions and code (no switch cases, no
> +	 * dw_mipi_dsi_dcs_short_write(), only the loop in long_write...)
> +	 * and use packet.header...
> +	 */
> +	dw_mipi_message_config(dsi, msg);
> +
> +	switch (msg->type) {
> +	case MIPI_DSI_DCS_SHORT_WRITE:
> +	case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
> +	case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE:
> +		ret = dw_mipi_dsi_dcs_short_write(dsi, msg);
> +		break;
> +	case MIPI_DSI_DCS_LONG_WRITE:
> +		ret = dw_mipi_dsi_dcs_long_write(dsi, msg);
> +		break;
> +	default:
> +		dev_err(dsi->dev, "unsupported message type 0x%02x\n",
> +			msg->type);
> +		ret = -EINVAL;
> +	}
> +
> +	return ret;
> +}
> +
> +static const struct mipi_dsi_host_ops dw_mipi_dsi_host_ops = {
> +	.attach = dw_mipi_dsi_host_attach,
> +	.detach = dw_mipi_dsi_host_detach,
> +	.transfer = dw_mipi_dsi_host_transfer,
> +};
> +
> +static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi)
> +{
> +	u32 val;
> +
> +	/*
> +	 * TODO dw drv improvements
> +	 * enabling low power is panel-dependent, we should use the
> +	 * panel configuration here...
> +	 */
> +	val = ENABLE_LOW_POWER;
> +
> +	if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
> +		val |= VID_MODE_TYPE_BURST;
> +	else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
> +		val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES;
> +	else
> +		val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS;
> +
> +	dsi_write(dsi, DSI_VID_MODE_CFG, val);
> +}
> +
> +static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi,
> +				 unsigned long mode_flags)
> +{
> +	dsi_write(dsi, DSI_PWR_UP, RESET);
> +
> +	if (mode_flags & MIPI_DSI_MODE_VIDEO) {
> +		dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE);
> +		dw_mipi_dsi_video_mode_config(dsi);
> +		dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS);
> +	} else {
> +		dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
> +	}
> +
> +	dsi_write(dsi, DSI_PWR_UP, POWERUP);
> +}
> +
> +static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
> +{
> +	dsi_write(dsi, DSI_PWR_UP, RESET);
> +	dsi_write(dsi, DSI_PHY_RSTZ, PHY_RSTZ);
> +}
> +
> +static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
> +{
> +	/*
> +	 * The maximum permitted escape clock is 20MHz and it is derived from
> +	 * lanebyteclk, which is running at "lane_mbps / 8".  Thus we want:
> +	 *
> +	 *     (lane_mbps >> 3) / esc_clk_division < 20
> +	 * which is:
> +	 *     (lane_mbps >> 3) / 20 > esc_clk_division
> +	 */
> +	u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1;
> +
> +	dsi_write(dsi, DSI_PWR_UP, RESET);
> +
> +	/*
> +	 * TODO dw drv improvements
> +	 * timeout clock division should be computed with the
> +	 * high speed transmission counter timeout and byte lane...
> +	 */
> +	dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
> +		  TX_ESC_CLK_DIVIDSION(esc_clk_division));
> +}
> +
> +static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
> +				   struct drm_display_mode *mode)
> +{
> +	u32 val = 0, color = 0;
> +
> +	switch (dsi->format) {
> +	case MIPI_DSI_FMT_RGB888:
> +		color = DPI_COLOR_CODING_24BIT;
> +		break;
> +	case MIPI_DSI_FMT_RGB666:
> +		color = DPI_COLOR_CODING_18BIT_2 | EN18_LOOSELY;
> +		break;
> +	case MIPI_DSI_FMT_RGB666_PACKED:
> +		color = DPI_COLOR_CODING_18BIT_1;
> +		break;
> +	case MIPI_DSI_FMT_RGB565:
> +		color = DPI_COLOR_CODING_16BIT_1;
> +		break;
> +	}
> +
> +	if (mode->flags & DRM_MODE_FLAG_NVSYNC)
> +		val |= VSYNC_ACTIVE_LOW;
> +	if (mode->flags & DRM_MODE_FLAG_NHSYNC)
> +		val |= HSYNC_ACTIVE_LOW;
> +
> +	dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel));
> +	dsi_write(dsi, DSI_DPI_COLOR_CODING, color);
> +	dsi_write(dsi, DSI_DPI_CFG_POL, val);
> +	/*
> +	 * TODO dw drv improvements
> +	 * largest packet sizes during hfp or during vsa/vpb/vfp
> +	 * should be computed according to byte lane, lane number and only
> +	 * if sending lp cmds in high speed is enable (PHY_TXREQUESTCLKHS)
> +	 */
> +	dsi_write(dsi, DSI_DPI_LP_CMD_TIM, OUTVACT_LPCMD_TIME(4)
> +		  | INVACT_LPCMD_TIME(4));
> +}
> +
> +static void dw_mipi_dsi_packet_handler_config(struct dw_mipi_dsi *dsi)
> +{
> +	dsi_write(dsi, DSI_PCKHDL_CFG, EN_CRC_RX | EN_ECC_RX | EN_BTA);
> +}
> +
> +static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi,
> +					    struct drm_display_mode *mode)
> +{
> +	/*
> +	 * TODO dw drv improvements
> +	 * only burst mode is supported here. For non-burst video modes,
> +	 * we should compute DSI_VID_PKT_SIZE, DSI_VCCR.NUMC &
> +	 * DSI_VNPCR.NPSIZE... especially because this driver supports
> +	 * non-burst video modes, see dw_mipi_dsi_video_mode_config()...
> +	 */
> +	dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay));
> +}
> +
> +static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
> +{
> +	/*
> +	 * TODO dw drv improvements
> +	 * compute high speed transmission counter timeout according
> +	 * to the timeout clock division (TO_CLK_DIVIDSION) and byte lane...
> +	 */
> +	dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000));
> +	/*
> +	 * TODO dw drv improvements
> +	 * the Bus-Turn-Around Timeout Counter should be computed
> +	 * according to byte lane...
> +	 */
> +	dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00);
> +	dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
> +}
> +
> +/* Get lane byte clock cycles. */
> +static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi,
> +					   struct drm_display_mode *mode,
> +					   u32 hcomponent)
> +{
> +	u32 frac, lbcc;
> +
> +	lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8;
> +
> +	frac = lbcc % mode->clock;
> +	lbcc = lbcc / mode->clock;
> +	if (frac)
> +		lbcc++;
> +
> +	return lbcc;
> +}
> +
> +static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi,
> +					  struct drm_display_mode *mode)
> +{
> +	u32 htotal, hsa, hbp, lbcc;
> +
> +	htotal = mode->htotal;
> +	hsa = mode->hsync_end - mode->hsync_start;
> +	hbp = mode->htotal - mode->hsync_end;
> +
> +	/*
> +	 * TODO dw drv improvements
> +	 * computations below may be improved...
> +	 */
> +	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, htotal);
> +	dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc);
> +
> +	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hsa);
> +	dsi_write(dsi, DSI_VID_HSA_TIME, lbcc);
> +
> +	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hbp);
> +	dsi_write(dsi, DSI_VID_HBP_TIME, lbcc);
> +}
> +
> +static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi,
> +					       struct drm_display_mode *mode)
> +{
> +	u32 vactive, vsa, vfp, vbp;
> +
> +	vactive = mode->vdisplay;
> +	vsa = mode->vsync_end - mode->vsync_start;
> +	vfp = mode->vsync_start - mode->vdisplay;
> +	vbp = mode->vtotal - mode->vsync_end;
> +
> +	dsi_write(dsi, DSI_VID_VACTIVE_LINES, vactive);
> +	dsi_write(dsi, DSI_VID_VSA_LINES, vsa);
> +	dsi_write(dsi, DSI_VID_VFP_LINES, vfp);
> +	dsi_write(dsi, DSI_VID_VBP_LINES, vbp);
> +}
> +
> +static void dw_mipi_dsi_dphy_timing_config(struct dw_mipi_dsi *dsi)
> +{
> +	/*
> +	 * TODO dw drv improvements
> +	 * data & clock lane timers should be computed according to panel
> +	 * blankings and to the automatic clock lane control mode...
> +	 * note: DSI_PHY_TMR_CFG.MAX_RD_TIME should be in line with
> +	 * DSI_CMD_MODE_CFG.MAX_RD_PKT_SIZE_LP (see CMD_MODE_ALL_LP)
> +	 */
> +	dsi_write(dsi, DSI_PHY_TMR_CFG, PHY_HS2LP_TIME(0x40)
> +		  | PHY_LP2HS_TIME(0x40) | MAX_RD_TIME(10000));
> +
> +	dsi_write(dsi, DSI_PHY_TMR_LPCLK_CFG, PHY_CLKHS2LP_TIME(0x40)
> +		  | PHY_CLKLP2HS_TIME(0x40));
> +}
> +
> +static void dw_mipi_dsi_dphy_interface_config(struct dw_mipi_dsi *dsi)
> +{
> +	/*
> +	 * TODO dw drv improvements
> +	 * stop wait time should be the maximum between host dsi
> +	 * and panel stop wait times
> +	 */
> +	dsi_write(dsi, DSI_PHY_IF_CFG, PHY_STOP_WAIT_TIME(0x20) |
> +		  N_LANES(dsi->lanes));
> +}
> +
> +static void dw_mipi_dsi_dphy_init(struct dw_mipi_dsi *dsi)
> +{
> +	/* Clear PHY state */
> +	dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
> +		  | PHY_RSTZ | PHY_SHUTDOWNZ);
> +	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
> +	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR);
> +	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
> +}
> +
> +static void dw_mipi_dsi_dphy_enable(struct dw_mipi_dsi *dsi)
> +{
> +	u32 val;
> +	int ret;
> +
> +	dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |
> +		  PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
> +
> +	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
> +				 val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US);
> +	if (ret < 0)
> +		DRM_DEBUG_DRIVER("failed to wait phy lock state\n");
> +
> +	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
> +				 val, val & STOP_STATE_CLK_LANE, 1000,
> +				 PHY_STATUS_TIMEOUT_US);
> +	if (ret < 0)
> +		DRM_DEBUG_DRIVER("failed to wait phy clk lane stop state\n");
> +}
> +
> +static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi)
> +{
> +	dsi_read(dsi, DSI_INT_ST0);
> +	dsi_read(dsi, DSI_INT_ST1);
> +	dsi_write(dsi, DSI_INT_MSK0, 0);
> +	dsi_write(dsi, DSI_INT_MSK1, 0);
> +}
> +
> +static void dw_mipi_dsi_bridge_disable(struct drm_bridge *bridge)
> +{
> +	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
> +
> +	if (dsi->dpms_mode != DRM_MODE_DPMS_ON)
> +		return;

dpms_mode doesn't seem to be used apart from bridge_disable/enable ops.
These would be called correctly by the drm core, so it should be okay to
drop it.

> +
> +	if (clk_enable(dsi->pclk)) {
> +		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
> +		return;
> +	}
> +
> +	drm_panel_disable(dsi->panel);
> +
> +	/* Switch to dsi command mode for the panel de-initialization */
> +	dw_mipi_dsi_set_mode(dsi, 0); > +	drm_panel_unprepare(dsi->panel);
> +
> +	dw_mipi_dsi_disable(dsi);
> +	pm_runtime_put(dsi->dev);
> +	clk_disable(dsi->pclk);
> +	dsi->dpms_mode = DRM_MODE_DPMS_OFF;
> +}
> +
> +static void dw_mipi_dsi_bridge_enable(struct drm_bridge *bridge)
> +{
> +	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
> +	struct drm_encoder *encoder = bridge->encoder;
> +	struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
> +	const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
> +	void *priv_data = dsi->plat_data->priv_data;
> +	int ret;
> +
> +	if (dsi->dpms_mode == DRM_MODE_DPMS_ON)
> +		return;
> +
> +	if (clk_enable(dsi->pclk)) {
> +		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
> +		return;
> +	}
> +
> +	ret = phy_ops->get_lane_mbps(priv_data, mode, dsi->mode_flags,
> +				     dsi->lanes, dsi->format, &dsi->lane_mbps);
> +	if (ret)
> +		DRM_DEBUG_DRIVER("Phy get_lane_mbps() failed\n");
> +
> +	pm_runtime_get_sync(dsi->dev);
> +	dw_mipi_dsi_init(dsi);
> +	dw_mipi_dsi_dpi_config(dsi, mode);
> +	dw_mipi_dsi_packet_handler_config(dsi);
> +	dw_mipi_dsi_video_mode_config(dsi);
> +	dw_mipi_dsi_video_packet_config(dsi, mode);
> +	dw_mipi_dsi_command_mode_config(dsi);
> +	dw_mipi_dsi_line_timer_config(dsi, mode);
> +	dw_mipi_dsi_vertical_timing_config(dsi, mode);
> +
> +	dw_mipi_dsi_dphy_init(dsi);
> +	dw_mipi_dsi_dphy_timing_config(dsi);
> +	dw_mipi_dsi_dphy_interface_config(dsi);
> +
> +	dw_mipi_dsi_clear_err(dsi);
> +
> +	ret = phy_ops->init(priv_data);
> +	if (ret)
> +		DRM_DEBUG_DRIVER("Phy init() failed\n");
> +
> +	dw_mipi_dsi_dphy_enable(dsi);
> +
> +	dw_mipi_dsi_wait_for_two_frames(mode);
> +
> +	/* Switch to dsi command mode for the panel initialization */
> +	dw_mipi_dsi_set_mode(dsi, 0);
> +	if (drm_panel_prepare(dsi->panel))
> +		dev_err(dsi->dev, "failed to prepare panel\n");
> +
> +	/* Switch to dsi video mode to send image data to the panel */
> +	dw_mipi_dsi_set_mode(dsi, MIPI_DSI_MODE_VIDEO);
> +	drm_panel_enable(dsi->panel);
> +
> +	clk_disable(dsi->pclk);
> +
> +	dsi->dpms_mode = DRM_MODE_DPMS_ON;
> +}
> +
> +static int dw_mipi_dsi_connector_get_modes(struct drm_connector *connector)
> +{
> +	struct dw_mipi_dsi *dsi = con_to_dsi(connector);
> +
> +	return drm_panel_get_modes(dsi->panel);
> +}
> +
> +static enum drm_mode_status
> +dw_mipi_dsi_mode_valid(struct drm_connector *connector,
> +		       struct drm_display_mode *mode)

Maybe we can consider using bridge's mode_valid() here?

> +{
> +	struct dw_mipi_dsi *dsi = con_to_dsi(connector);
> +	const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data;
> +	enum drm_mode_status mode_status = MODE_OK;
> +
> +	if (pdata->mode_valid)
> +		mode_status = pdata->mode_valid(pdata->priv_data,
> +						connector, mode);
> +
> +	return mode_status;
> +}
> +
> +static struct drm_connector_helper_funcs dw_mipi_dsi_connector_helper_funcs = {
> +	.get_modes = dw_mipi_dsi_connector_get_modes,
> +	.mode_valid = dw_mipi_dsi_mode_valid,
> +};
> +
> +static void dw_mipi_dsi_drm_connector_destroy(struct drm_connector *connector)
> +{
> +	drm_connector_unregister(connector);

We aren't supposed to register/unregister the connector in the bridge driver. It
should be done by the KMS driver. You could drop this and use drm_connector_cleanup()
directly for the .destroy op below.

> +	drm_connector_cleanup(connector);
> +}
> +
> +static const struct drm_connector_funcs dw_mipi_dsi_atomic_connector_funcs = {
> +	.dpms = drm_atomic_helper_connector_dpms,
> +	.fill_modes = drm_helper_probe_single_connector_modes,
> +	.destroy = dw_mipi_dsi_drm_connector_destroy,
> +	.reset = drm_atomic_helper_connector_reset,
> +	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> +	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> +};
> +
> +static int dw_mipi_dsi_bridge_attach(struct drm_bridge *bridge)
> +{
> +	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
> +	struct drm_connector *connector = &dsi->connector;
> +
> +	if (!bridge->encoder) {
> +		DRM_ERROR("Parent encoder object not found\n");
> +		return -ENODEV;
> +	}
> +
> +	/* Set the encoder type as caller does not know it */
> +	bridge->encoder->encoder_type = DRM_MODE_ENCODER_DSI;
> +
> +	connector->polled = DRM_CONNECTOR_POLL_HPD;

We don't need to set the polled field here.

> +
> +	drm_connector_helper_add(connector,
> +				 &dw_mipi_dsi_connector_helper_funcs);
> +
> +	drm_connector_init(bridge->dev, connector,
> +			   &dw_mipi_dsi_atomic_connector_funcs,
> +			   DRM_MODE_CONNECTOR_DSI);
> +
> +	drm_mode_connector_attach_encoder(connector, bridge->encoder);
> +
> +	return 0;
> +}
> +
> +static struct drm_bridge_funcs dw_mipi_dsi_bridge_funcs = {
> +	.enable = dw_mipi_dsi_bridge_enable,
> +	.disable = dw_mipi_dsi_bridge_disable,
> +	.attach = dw_mipi_dsi_bridge_attach,
> +};
> +
> +static struct dw_mipi_dsi *
> +__dw_mipi_dsi_probe(struct platform_device *pdev,
> +		    const struct dw_mipi_dsi_plat_data *plat_data)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct reset_control *apb_rst;
> +	struct dw_mipi_dsi *dsi;
> +	struct resource *res;
> +	int ret;
> +
> +	dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
> +	if (!dsi)
> +		return ERR_PTR(-ENOMEM);
> +
> +	dsi->dev = dev;
> +	dsi->plat_data = plat_data;
> +	dsi->dpms_mode = DRM_MODE_DPMS_OFF;
> +
> +	if (!plat_data->phy_ops->init || !plat_data->phy_ops->get_lane_mbps) {
> +		DRM_ERROR("Phy not properly configured\n");
> +		return ERR_PTR(-ENODEV);
> +	}
> +
> +	if (!plat_data->base) {
> +		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +		if (!res)
> +			return ERR_PTR(-ENODEV);
> +
> +		dsi->base = devm_ioremap_resource(dev, res);
> +		if (IS_ERR(dsi->base))
> +			return ERR_PTR(-ENODEV);
> +
> +	} else {
> +		dsi->base = plat_data->base;
> +	}
> +
> +	dsi->pclk = devm_clk_get(dev, "pclk");
> +	if (IS_ERR(dsi->pclk)) {
> +		ret = PTR_ERR(dsi->pclk);
> +		dev_err(dev, "Unable to get pclk: %d\n", ret);
> +		return ERR_PTR(ret);
> +	}
> +
> +	/*
> +	 * Note that the reset was not defined in the initial device tree, so
> +	 * we have to be prepared for it not being found.
> +	 */
> +	apb_rst = devm_reset_control_get(dev, "apb");
> +	if (IS_ERR(apb_rst)) {
> +		ret = PTR_ERR(apb_rst);
> +		if (ret == -ENOENT) {
> +			apb_rst = NULL;
> +		} else {
> +			dev_err(dev, "Unable to get reset control: %d\n", ret);
> +			return ERR_PTR(ret);
> +		}
> +	}
> +
> +	if (apb_rst) {
> +		ret = clk_prepare_enable(dsi->pclk);
> +		if (ret) {
> +			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
> +			return ERR_PTR(ret);
> +		}
> +
> +		reset_control_assert(apb_rst);
> +		usleep_range(10, 20);
> +		reset_control_deassert(apb_rst);
> +
> +		clk_disable(dsi->pclk);

		clk_disable_unprepare here ?
> +	}
> +
> +	pm_runtime_enable(dev);
> +
> +	dsi->dsi_host.ops = &dw_mipi_dsi_host_ops;
> +	dsi->dsi_host.dev = dev;
> +	ret = mipi_dsi_host_register(&dsi->dsi_host);
> +	if (ret) {
> +		dev_err(dev, "Failed to register MIPI host: %d\n", ret);
> +		return ERR_PTR(ret);
> +	}
> +
> +	dsi->bridge.driver_private = dsi;
> +	dsi->bridge.funcs = &dw_mipi_dsi_bridge_funcs;
> +#ifdef CONFIG_OF
> +	dsi->bridge.of_node = pdev->dev.of_node;
> +#endif
> +
> +	clk_enable(dsi->pclk);

Is this really needed here? It looks like we take care of enabling/disabling
it in the bridge ops. If it's still needed, we should atleast put a corresponding
disable in __dw_mipi_dsi_remove().

> +
> +	dev_set_drvdata(dev, dsi);
> +
> +	return dsi;
> +}
> +
> +static void __dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi)
> +{
> +	pm_runtime_disable(dsi->dev);
> +}
> +
> +/*
> + * Probe/remove API, used from platforms based on the DRM bridge API.
> + */
> +int dw_mipi_dsi_probe(struct platform_device *pdev,
> +		      const struct dw_mipi_dsi_plat_data *plat_data)
> +{
> +	struct dw_mipi_dsi *dsi;
> +	int ret;
> +
> +	dsi = __dw_mipi_dsi_probe(pdev, plat_data);
> +	if (IS_ERR(dsi))
> +		return PTR_ERR(dsi);
> +
> +	ret = drm_bridge_add(&dsi->bridge);
> +	if (ret < 0) {
> +		__dw_mipi_dsi_remove(dsi);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi_probe);
> +
> +void dw_mipi_dsi_remove(struct platform_device *pdev)
> +{
> +	struct dw_mipi_dsi *dsi = platform_get_drvdata(pdev);
> +
> +	mipi_dsi_host_unregister(&dsi->dsi_host);
> +	drm_bridge_remove(&dsi->bridge);
> +
> +	__dw_mipi_dsi_remove(dsi);
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi_remove);
> +
> +/*
> + * Bind/unbind API, used from platforms based on the component framework.
> + */
> +int dw_mipi_dsi_bind(struct platform_device *pdev, struct drm_encoder *encoder,
> +		     const struct dw_mipi_dsi_plat_data *plat_data)
> +{
> +	struct dw_mipi_dsi *dsi;
> +	int ret;
> +
> +	dsi = __dw_mipi_dsi_probe(pdev, plat_data);
> +	if (IS_ERR(dsi))
> +		return PTR_ERR(dsi);
> +
> +	ret = drm_bridge_attach(encoder, &dsi->bridge, NULL);
> +	if (ret) {
> +		dw_mipi_dsi_remove(pdev);
> +		DRM_ERROR("Failed to initialize bridge with drm\n");
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi_bind);
> +
> +void dw_mipi_dsi_unbind(struct device *dev)
> +{
> +	struct dw_mipi_dsi *dsi = dev_get_drvdata(dev);
> +
> +	__dw_mipi_dsi_remove(dsi);
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi_unbind);
> +
> +MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
> +MODULE_AUTHOR("Philippe Cornu <philippe.cornu@st.com>");
> +MODULE_DESCRIPTION("DW MIPI DSI host controller driver");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("platform:dw-mipi-dsi");
> diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h
> new file mode 100644
> index 0000000..2043a37
> --- /dev/null
> +++ b/include/drm/bridge/dw_mipi_dsi.h
> @@ -0,0 +1,42 @@
> +/*
> + * Copyright (C) STMicroelectronics SA 2017
> + *
> + * Authors: Philippe Cornu <philippe.cornu@st.com>
> + *          Yannick Fertre <yannick.fertre@st.com>
> + *
> + * License terms:  GNU General Public License (GPL), version 2
> + */
> +
> +#ifndef __DW_MIPI_DSI__
> +#define __DW_MIPI_DSI__
> +
> +#include <drm/drmP.h>

Can you cross check if the above header is needed?

Thanks,
Archit

> +
> +struct dw_mipi_dsi_phy_ops {
> +	int (*init)(void *priv_data);
> +	int (*get_lane_mbps)(void *priv_data, struct drm_display_mode *mode,
> +			     unsigned long mode_flags, u32 lanes, u32 format,
> +			     unsigned int *lane_mbps);
> +};
> +
> +struct dw_mipi_dsi_plat_data {
> +	void __iomem *base;
> +	unsigned int max_data_lanes;
> +
> +	enum drm_mode_status (*mode_valid)(void *priv_data,
> +					   struct drm_connector *connector,
> +					   struct drm_display_mode *mode);
> +
> +	const struct dw_mipi_dsi_phy_ops *phy_ops;
> +
> +	void *priv_data;
> +};
> +
> +int dw_mipi_dsi_probe(struct platform_device *pdev,
> +		      const struct dw_mipi_dsi_plat_data *plat_data);
> +void dw_mipi_dsi_remove(struct platform_device *pdev);
> +int dw_mipi_dsi_bind(struct platform_device *pdev, struct drm_encoder *encoder,
> +		     const struct dw_mipi_dsi_plat_data *plat_data);
> +void dw_mipi_dsi_unbind(struct device *dev);
> +
> +#endif /* __DW_MIPI_DSI__ */
>
diff mbox

Patch

diff --git a/drivers/gpu/drm/bridge/synopsys/Kconfig b/drivers/gpu/drm/bridge/synopsys/Kconfig
index 40d2827..d7fbdff 100644
--- a/drivers/gpu/drm/bridge/synopsys/Kconfig
+++ b/drivers/gpu/drm/bridge/synopsys/Kconfig
@@ -21,3 +21,12 @@  config DRM_DW_HDMI_I2S_AUDIO
 	help
 	  Support the I2S Audio interface which is part of the Synopsys
 	  Designware HDMI block.
+
+config DRM_DW_MIPI_DSI
+	tristate "Synopsys DesignWare MIPI DSI host controller bridge"
+	select DRM_KMS_HELPER
+	select DRM_MIPI_DSI
+	select DRM_PANEL
+	help
+	  Choose this if you want to use the Synopsys DesignWare MIPI DSI host
+	  controller bridge.
diff --git a/drivers/gpu/drm/bridge/synopsys/Makefile b/drivers/gpu/drm/bridge/synopsys/Makefile
index 17aa7a6..5f57d36 100644
--- a/drivers/gpu/drm/bridge/synopsys/Makefile
+++ b/drivers/gpu/drm/bridge/synopsys/Makefile
@@ -3,3 +3,5 @@ 
 obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
 obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
 obj-$(CONFIG_DRM_DW_HDMI_I2S_AUDIO) += dw-hdmi-i2s-audio.o
+
+obj-$(CONFIG_DRM_DW_MIPI_DSI) += dw-mipi-dsi.o
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
new file mode 100644
index 0000000..6b25629
--- /dev/null
+++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
@@ -0,0 +1,1022 @@ 
+/*
+ * Copyright (c) 2016, Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Modified by Philippe Cornu <philippe.cornu@st.com>
+ * This generic Synopsys Designware MIPI DSI host driver is based on the
+ * Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.
+ */
+
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/reset.h>
+#include <drm/drmP.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_of.h>
+#include <drm/drm_panel.h>
+#include <drm/bridge/dw_mipi_dsi.h>
+#include <video/mipi_display.h>
+
+#define DSI_VERSION			0x00
+#define DSI_PWR_UP			0x04
+#define RESET				0
+#define POWERUP				BIT(0)
+
+#define DSI_CLKMGR_CFG			0x08
+#define TO_CLK_DIVIDSION(div)		(((div) & 0xff) << 8)
+#define TX_ESC_CLK_DIVIDSION(div)	(((div) & 0xff) << 0)
+
+#define DSI_DPI_VCID			0x0c
+#define DPI_VID(vid)			(((vid) & 0x3) << 0)
+
+#define DSI_DPI_COLOR_CODING		0x10
+#define EN18_LOOSELY			BIT(8)
+#define DPI_COLOR_CODING_16BIT_1	0x0
+#define DPI_COLOR_CODING_16BIT_2	0x1
+#define DPI_COLOR_CODING_16BIT_3	0x2
+#define DPI_COLOR_CODING_18BIT_1	0x3
+#define DPI_COLOR_CODING_18BIT_2	0x4
+#define DPI_COLOR_CODING_24BIT		0x5
+
+#define DSI_DPI_CFG_POL			0x14
+#define COLORM_ACTIVE_LOW		BIT(4)
+#define SHUTD_ACTIVE_LOW		BIT(3)
+#define HSYNC_ACTIVE_LOW		BIT(2)
+#define VSYNC_ACTIVE_LOW		BIT(1)
+#define DATAEN_ACTIVE_LOW		BIT(0)
+
+#define DSI_DPI_LP_CMD_TIM		0x18
+#define OUTVACT_LPCMD_TIME(p)		(((p) & 0xff) << 16)
+#define INVACT_LPCMD_TIME(p)		((p) & 0xff)
+
+#define DSI_DBI_CFG			0x20
+#define DSI_DBI_CMDSIZE			0x28
+
+#define DSI_PCKHDL_CFG			0x2c
+#define EN_CRC_RX			BIT(4)
+#define EN_ECC_RX			BIT(3)
+#define EN_BTA				BIT(2)
+#define EN_EOTP_RX			BIT(1)
+#define EN_EOTP_TX			BIT(0)
+
+#define DSI_MODE_CFG			0x34
+#define ENABLE_VIDEO_MODE		0
+#define ENABLE_CMD_MODE			BIT(0)
+
+#define DSI_VID_MODE_CFG		0x38
+#define FRAME_BTA_ACK			BIT(14)
+#define ENABLE_LOW_POWER		(0x3f << 8)
+#define ENABLE_LOW_POWER_MASK		(0x3f << 8)
+#define VID_MODE_TYPE_NON_BURST_SYNC_PULSES	0x0
+#define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS	0x1
+#define VID_MODE_TYPE_BURST			0x2
+#define VID_MODE_TYPE_MASK			0x3
+
+#define DSI_VID_PKT_SIZE		0x3c
+#define VID_PKT_SIZE(p)			(((p) & 0x3fff) << 0)
+#define VID_PKT_MAX_SIZE		0x3fff
+
+#define DSI_VID_HSA_TIME		0x48
+#define DSI_VID_HBP_TIME		0x4c
+#define DSI_VID_HLINE_TIME		0x50
+#define DSI_VID_VSA_LINES		0x54
+#define DSI_VID_VBP_LINES		0x58
+#define DSI_VID_VFP_LINES		0x5c
+#define DSI_VID_VACTIVE_LINES		0x60
+#define DSI_CMD_MODE_CFG		0x68
+#define MAX_RD_PKT_SIZE_LP		BIT(24)
+#define DCS_LW_TX_LP			BIT(19)
+#define DCS_SR_0P_TX_LP			BIT(18)
+#define DCS_SW_1P_TX_LP			BIT(17)
+#define DCS_SW_0P_TX_LP			BIT(16)
+#define GEN_LW_TX_LP			BIT(14)
+#define GEN_SR_2P_TX_LP			BIT(13)
+#define GEN_SR_1P_TX_LP			BIT(12)
+#define GEN_SR_0P_TX_LP			BIT(11)
+#define GEN_SW_2P_TX_LP			BIT(10)
+#define GEN_SW_1P_TX_LP			BIT(9)
+#define GEN_SW_0P_TX_LP			BIT(8)
+#define EN_ACK_RQST			BIT(1)
+#define EN_TEAR_FX			BIT(0)
+
+#define CMD_MODE_ALL_LP			(MAX_RD_PKT_SIZE_LP | \
+					 DCS_LW_TX_LP | \
+					 DCS_SR_0P_TX_LP | \
+					 DCS_SW_1P_TX_LP | \
+					 DCS_SW_0P_TX_LP | \
+					 GEN_LW_TX_LP | \
+					 GEN_SR_2P_TX_LP | \
+					 GEN_SR_1P_TX_LP | \
+					 GEN_SR_0P_TX_LP | \
+					 GEN_SW_2P_TX_LP | \
+					 GEN_SW_1P_TX_LP | \
+					 GEN_SW_0P_TX_LP)
+
+#define DSI_GEN_HDR			0x6c
+#define GEN_HDATA(data)			(((data) & 0xffff) << 8)
+#define GEN_HDATA_MASK			(0xffff << 8)
+#define GEN_HTYPE(type)			(((type) & 0xff) << 0)
+#define GEN_HTYPE_MASK			0xff
+
+#define DSI_GEN_PLD_DATA		0x70
+
+#define DSI_CMD_PKT_STATUS		0x74
+#define GEN_CMD_EMPTY			BIT(0)
+#define GEN_CMD_FULL			BIT(1)
+#define GEN_PLD_W_EMPTY			BIT(2)
+#define GEN_PLD_W_FULL			BIT(3)
+#define GEN_PLD_R_EMPTY			BIT(4)
+#define GEN_PLD_R_FULL			BIT(5)
+#define GEN_RD_CMD_BUSY			BIT(6)
+
+#define DSI_TO_CNT_CFG			0x78
+#define HSTX_TO_CNT(p)			(((p) & 0xffff) << 16)
+#define LPRX_TO_CNT(p)			((p) & 0xffff)
+
+#define DSI_BTA_TO_CNT			0x8c
+#define DSI_LPCLK_CTRL			0x94
+#define AUTO_CLKLANE_CTRL		BIT(1)
+#define PHY_TXREQUESTCLKHS		BIT(0)
+
+#define DSI_PHY_TMR_LPCLK_CFG		0x98
+#define PHY_CLKHS2LP_TIME(lbcc)		(((lbcc) & 0x3ff) << 16)
+#define PHY_CLKLP2HS_TIME(lbcc)		((lbcc) & 0x3ff)
+
+#define DSI_PHY_TMR_CFG			0x9c
+#define PHY_HS2LP_TIME(lbcc)		(((lbcc) & 0xff) << 24)
+#define PHY_LP2HS_TIME(lbcc)		(((lbcc) & 0xff) << 16)
+#define MAX_RD_TIME(lbcc)		((lbcc) & 0x7fff)
+
+#define DSI_PHY_RSTZ			0xa0
+#define PHY_DISFORCEPLL			0
+#define PHY_ENFORCEPLL			BIT(3)
+#define PHY_DISABLECLK			0
+#define PHY_ENABLECLK			BIT(2)
+#define PHY_RSTZ			0
+#define PHY_UNRSTZ			BIT(1)
+#define PHY_SHUTDOWNZ			0
+#define PHY_UNSHUTDOWNZ			BIT(0)
+
+#define DSI_PHY_IF_CFG			0xa4
+#define N_LANES(n)			((((n) - 1) & 0x3) << 0)
+#define PHY_STOP_WAIT_TIME(cycle)	(((cycle) & 0xff) << 8)
+
+#define DSI_PHY_STATUS			0xb0
+#define LOCK				BIT(0)
+#define STOP_STATE_CLK_LANE		BIT(2)
+
+#define DSI_PHY_TST_CTRL0		0xb4
+#define PHY_TESTCLK			BIT(1)
+#define PHY_UNTESTCLK			0
+#define PHY_TESTCLR			BIT(0)
+#define PHY_UNTESTCLR			0
+
+#define DSI_PHY_TST_CTRL1		0xb8
+#define PHY_TESTEN			BIT(16)
+#define PHY_UNTESTEN			0
+#define PHY_TESTDOUT(n)			(((n) & 0xff) << 8)
+#define PHY_TESTDIN(n)			(((n) & 0xff) << 0)
+
+#define DSI_INT_ST0			0xbc
+#define DSI_INT_ST1			0xc0
+#define DSI_INT_MSK0			0xc4
+#define DSI_INT_MSK1			0xc8
+
+#define PHY_STATUS_TIMEOUT_US		10000
+#define CMD_PKT_STATUS_TIMEOUT_US	20000
+
+struct dw_mipi_dsi {
+	struct drm_bridge bridge;
+	struct drm_connector connector;
+	struct mipi_dsi_host dsi_host;
+	struct drm_panel *panel;
+	struct device *dev;
+	void __iomem *base;
+
+	struct clk *pclk;
+
+	int dpms_mode;
+	unsigned int lane_mbps; /* per lane */
+	u32 channel;
+	u32 lanes;
+	u32 format;
+	unsigned long mode_flags;
+
+	const struct dw_mipi_dsi_plat_data *plat_data;
+};
+
+/*
+ * The controller should generate 2 frames before
+ * preparing the peripheral.
+ */
+static void dw_mipi_dsi_wait_for_two_frames(struct drm_display_mode *mode)
+{
+	int refresh, two_frames;
+
+	refresh = drm_mode_vrefresh(mode);
+	two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2;
+	msleep(two_frames);
+}
+
+static inline struct dw_mipi_dsi *host_to_dsi(struct mipi_dsi_host *host)
+{
+	return container_of(host, struct dw_mipi_dsi, dsi_host);
+}
+
+static inline struct dw_mipi_dsi *con_to_dsi(struct drm_connector *con)
+{
+	return container_of(con, struct dw_mipi_dsi, connector);
+}
+
+static inline struct dw_mipi_dsi *bridge_to_dsi(struct drm_bridge *bridge)
+{
+	return container_of(bridge, struct dw_mipi_dsi, bridge);
+}
+
+static inline void dsi_write(struct dw_mipi_dsi *dsi, u32 reg, u32 val)
+{
+	writel_relaxed(val, dsi->base + reg);
+}
+
+static inline u32 dsi_read(struct dw_mipi_dsi *dsi, u32 reg)
+{
+	return readl_relaxed(dsi->base + reg);
+}
+
+static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
+				   struct mipi_dsi_device *device)
+{
+	struct dw_mipi_dsi *dsi = host_to_dsi(host);
+
+	if (device->lanes > dsi->plat_data->max_data_lanes) {
+		dev_err(dsi->dev, "the number of data lanes(%u) is too many\n",
+			device->lanes);
+		return -EINVAL;
+	}
+
+	dsi->lanes = device->lanes;
+	dsi->channel = device->channel;
+	dsi->format = device->format;
+	dsi->mode_flags = device->mode_flags;
+	dsi->panel = of_drm_find_panel(device->dev.of_node);
+	if (dsi->panel)
+		return drm_panel_attach(dsi->panel, &dsi->connector);
+
+	return -EINVAL;
+}
+
+static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
+				   struct mipi_dsi_device *device)
+{
+	struct dw_mipi_dsi *dsi = host_to_dsi(host);
+
+	drm_panel_detach(dsi->panel);
+
+	return 0;
+}
+
+static void dw_mipi_message_config(struct dw_mipi_dsi *dsi,
+				   const struct mipi_dsi_msg *msg)
+{
+	bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM;
+	u32 val = 0;
+
+	if (msg->flags & MIPI_DSI_MSG_REQ_ACK)
+		val |= EN_ACK_RQST;
+	if (lpm)
+		val |= CMD_MODE_ALL_LP;
+
+	dsi_write(dsi, DSI_LPCLK_CTRL, lpm ? 0 : PHY_TXREQUESTCLKHS);
+	dsi_write(dsi, DSI_CMD_MODE_CFG, val);
+}
+
+static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
+{
+	int ret;
+	u32 val, mask;
+
+	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
+				 val, !(val & GEN_CMD_FULL), 1000,
+				 CMD_PKT_STATUS_TIMEOUT_US);
+	if (ret < 0) {
+		dev_err(dsi->dev, "failed to get available command FIFO\n");
+		return ret;
+	}
+
+	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
+
+	mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
+	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
+				 val, (val & mask) == mask,
+				 1000, CMD_PKT_STATUS_TIMEOUT_US);
+	if (ret < 0) {
+		dev_err(dsi->dev, "failed to write command FIFO\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
+				       const struct mipi_dsi_msg *msg)
+{
+	const u8 *tx_buf = msg->tx_buf;
+	u16 data = 0;
+	u32 val;
+
+	if (msg->tx_len > 0)
+		data |= tx_buf[0];
+	if (msg->tx_len > 1)
+		data |= tx_buf[1] << 8;
+
+	if (msg->tx_len > 2) {
+		dev_err(dsi->dev, "too long tx buf length %zu for short write\n",
+			msg->tx_len);
+		return -EINVAL;
+	}
+
+	val = GEN_HDATA(data) | GEN_HTYPE(msg->type);
+	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
+}
+
+static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
+				      const struct mipi_dsi_msg *msg)
+{
+	const u8 *tx_buf = msg->tx_buf;
+	int len = msg->tx_len, pld_data_bytes = sizeof(u32), ret;
+	u32 hdr_val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
+	u32 remainder;
+	u32 val;
+
+	if (msg->tx_len < 3) {
+		dev_err(dsi->dev, "wrong tx buf length %zu for long write\n",
+			msg->tx_len);
+		return -EINVAL;
+	}
+
+	while (DIV_ROUND_UP(len, pld_data_bytes)) {
+		if (len < pld_data_bytes) {
+			remainder = 0;
+			memcpy(&remainder, tx_buf, len);
+			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
+			len = 0;
+		} else {
+			memcpy(&remainder, tx_buf, pld_data_bytes);
+			dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
+			tx_buf += pld_data_bytes;
+			len -= pld_data_bytes;
+		}
+
+		ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
+					 val, !(val & GEN_PLD_W_FULL), 1000,
+					 CMD_PKT_STATUS_TIMEOUT_US);
+		if (ret < 0) {
+			dev_err(dsi->dev,
+				"failed to get available write payload FIFO\n");
+			return ret;
+		}
+	}
+
+	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, hdr_val);
+}
+
+static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
+					 const struct mipi_dsi_msg *msg)
+{
+	struct dw_mipi_dsi *dsi = host_to_dsi(host);
+	int ret;
+
+	/*
+	 * TODO dw drv improvements
+	 * use mipi_dsi_create_packet() instead of all following
+	 * functions and code (no switch cases, no
+	 * dw_mipi_dsi_dcs_short_write(), only the loop in long_write...)
+	 * and use packet.header...
+	 */
+	dw_mipi_message_config(dsi, msg);
+
+	switch (msg->type) {
+	case MIPI_DSI_DCS_SHORT_WRITE:
+	case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
+	case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE:
+		ret = dw_mipi_dsi_dcs_short_write(dsi, msg);
+		break;
+	case MIPI_DSI_DCS_LONG_WRITE:
+		ret = dw_mipi_dsi_dcs_long_write(dsi, msg);
+		break;
+	default:
+		dev_err(dsi->dev, "unsupported message type 0x%02x\n",
+			msg->type);
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static const struct mipi_dsi_host_ops dw_mipi_dsi_host_ops = {
+	.attach = dw_mipi_dsi_host_attach,
+	.detach = dw_mipi_dsi_host_detach,
+	.transfer = dw_mipi_dsi_host_transfer,
+};
+
+static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi)
+{
+	u32 val;
+
+	/*
+	 * TODO dw drv improvements
+	 * enabling low power is panel-dependent, we should use the
+	 * panel configuration here...
+	 */
+	val = ENABLE_LOW_POWER;
+
+	if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
+		val |= VID_MODE_TYPE_BURST;
+	else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES;
+	else
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS;
+
+	dsi_write(dsi, DSI_VID_MODE_CFG, val);
+}
+
+static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi,
+				 unsigned long mode_flags)
+{
+	dsi_write(dsi, DSI_PWR_UP, RESET);
+
+	if (mode_flags & MIPI_DSI_MODE_VIDEO) {
+		dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE);
+		dw_mipi_dsi_video_mode_config(dsi);
+		dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS);
+	} else {
+		dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
+	}
+
+	dsi_write(dsi, DSI_PWR_UP, POWERUP);
+}
+
+static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
+{
+	dsi_write(dsi, DSI_PWR_UP, RESET);
+	dsi_write(dsi, DSI_PHY_RSTZ, PHY_RSTZ);
+}
+
+static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
+{
+	/*
+	 * The maximum permitted escape clock is 20MHz and it is derived from
+	 * lanebyteclk, which is running at "lane_mbps / 8".  Thus we want:
+	 *
+	 *     (lane_mbps >> 3) / esc_clk_division < 20
+	 * which is:
+	 *     (lane_mbps >> 3) / 20 > esc_clk_division
+	 */
+	u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1;
+
+	dsi_write(dsi, DSI_PWR_UP, RESET);
+
+	/*
+	 * TODO dw drv improvements
+	 * timeout clock division should be computed with the
+	 * high speed transmission counter timeout and byte lane...
+	 */
+	dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
+		  TX_ESC_CLK_DIVIDSION(esc_clk_division));
+}
+
+static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
+				   struct drm_display_mode *mode)
+{
+	u32 val = 0, color = 0;
+
+	switch (dsi->format) {
+	case MIPI_DSI_FMT_RGB888:
+		color = DPI_COLOR_CODING_24BIT;
+		break;
+	case MIPI_DSI_FMT_RGB666:
+		color = DPI_COLOR_CODING_18BIT_2 | EN18_LOOSELY;
+		break;
+	case MIPI_DSI_FMT_RGB666_PACKED:
+		color = DPI_COLOR_CODING_18BIT_1;
+		break;
+	case MIPI_DSI_FMT_RGB565:
+		color = DPI_COLOR_CODING_16BIT_1;
+		break;
+	}
+
+	if (mode->flags & DRM_MODE_FLAG_NVSYNC)
+		val |= VSYNC_ACTIVE_LOW;
+	if (mode->flags & DRM_MODE_FLAG_NHSYNC)
+		val |= HSYNC_ACTIVE_LOW;
+
+	dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel));
+	dsi_write(dsi, DSI_DPI_COLOR_CODING, color);
+	dsi_write(dsi, DSI_DPI_CFG_POL, val);
+	/*
+	 * TODO dw drv improvements
+	 * largest packet sizes during hfp or during vsa/vpb/vfp
+	 * should be computed according to byte lane, lane number and only
+	 * if sending lp cmds in high speed is enable (PHY_TXREQUESTCLKHS)
+	 */
+	dsi_write(dsi, DSI_DPI_LP_CMD_TIM, OUTVACT_LPCMD_TIME(4)
+		  | INVACT_LPCMD_TIME(4));
+}
+
+static void dw_mipi_dsi_packet_handler_config(struct dw_mipi_dsi *dsi)
+{
+	dsi_write(dsi, DSI_PCKHDL_CFG, EN_CRC_RX | EN_ECC_RX | EN_BTA);
+}
+
+static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi,
+					    struct drm_display_mode *mode)
+{
+	/*
+	 * TODO dw drv improvements
+	 * only burst mode is supported here. For non-burst video modes,
+	 * we should compute DSI_VID_PKT_SIZE, DSI_VCCR.NUMC &
+	 * DSI_VNPCR.NPSIZE... especially because this driver supports
+	 * non-burst video modes, see dw_mipi_dsi_video_mode_config()...
+	 */
+	dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay));
+}
+
+static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
+{
+	/*
+	 * TODO dw drv improvements
+	 * compute high speed transmission counter timeout according
+	 * to the timeout clock division (TO_CLK_DIVIDSION) and byte lane...
+	 */
+	dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000));
+	/*
+	 * TODO dw drv improvements
+	 * the Bus-Turn-Around Timeout Counter should be computed
+	 * according to byte lane...
+	 */
+	dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00);
+	dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
+}
+
+/* Get lane byte clock cycles. */
+static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi,
+					   struct drm_display_mode *mode,
+					   u32 hcomponent)
+{
+	u32 frac, lbcc;
+
+	lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8;
+
+	frac = lbcc % mode->clock;
+	lbcc = lbcc / mode->clock;
+	if (frac)
+		lbcc++;
+
+	return lbcc;
+}
+
+static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi,
+					  struct drm_display_mode *mode)
+{
+	u32 htotal, hsa, hbp, lbcc;
+
+	htotal = mode->htotal;
+	hsa = mode->hsync_end - mode->hsync_start;
+	hbp = mode->htotal - mode->hsync_end;
+
+	/*
+	 * TODO dw drv improvements
+	 * computations below may be improved...
+	 */
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, htotal);
+	dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc);
+
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hsa);
+	dsi_write(dsi, DSI_VID_HSA_TIME, lbcc);
+
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hbp);
+	dsi_write(dsi, DSI_VID_HBP_TIME, lbcc);
+}
+
+static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi,
+					       struct drm_display_mode *mode)
+{
+	u32 vactive, vsa, vfp, vbp;
+
+	vactive = mode->vdisplay;
+	vsa = mode->vsync_end - mode->vsync_start;
+	vfp = mode->vsync_start - mode->vdisplay;
+	vbp = mode->vtotal - mode->vsync_end;
+
+	dsi_write(dsi, DSI_VID_VACTIVE_LINES, vactive);
+	dsi_write(dsi, DSI_VID_VSA_LINES, vsa);
+	dsi_write(dsi, DSI_VID_VFP_LINES, vfp);
+	dsi_write(dsi, DSI_VID_VBP_LINES, vbp);
+}
+
+static void dw_mipi_dsi_dphy_timing_config(struct dw_mipi_dsi *dsi)
+{
+	/*
+	 * TODO dw drv improvements
+	 * data & clock lane timers should be computed according to panel
+	 * blankings and to the automatic clock lane control mode...
+	 * note: DSI_PHY_TMR_CFG.MAX_RD_TIME should be in line with
+	 * DSI_CMD_MODE_CFG.MAX_RD_PKT_SIZE_LP (see CMD_MODE_ALL_LP)
+	 */
+	dsi_write(dsi, DSI_PHY_TMR_CFG, PHY_HS2LP_TIME(0x40)
+		  | PHY_LP2HS_TIME(0x40) | MAX_RD_TIME(10000));
+
+	dsi_write(dsi, DSI_PHY_TMR_LPCLK_CFG, PHY_CLKHS2LP_TIME(0x40)
+		  | PHY_CLKLP2HS_TIME(0x40));
+}
+
+static void dw_mipi_dsi_dphy_interface_config(struct dw_mipi_dsi *dsi)
+{
+	/*
+	 * TODO dw drv improvements
+	 * stop wait time should be the maximum between host dsi
+	 * and panel stop wait times
+	 */
+	dsi_write(dsi, DSI_PHY_IF_CFG, PHY_STOP_WAIT_TIME(0x20) |
+		  N_LANES(dsi->lanes));
+}
+
+static void dw_mipi_dsi_dphy_init(struct dw_mipi_dsi *dsi)
+{
+	/* Clear PHY state */
+	dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
+		  | PHY_RSTZ | PHY_SHUTDOWNZ);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
+}
+
+static void dw_mipi_dsi_dphy_enable(struct dw_mipi_dsi *dsi)
+{
+	u32 val;
+	int ret;
+
+	dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |
+		  PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
+
+	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
+				 val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US);
+	if (ret < 0)
+		DRM_DEBUG_DRIVER("failed to wait phy lock state\n");
+
+	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
+				 val, val & STOP_STATE_CLK_LANE, 1000,
+				 PHY_STATUS_TIMEOUT_US);
+	if (ret < 0)
+		DRM_DEBUG_DRIVER("failed to wait phy clk lane stop state\n");
+}
+
+static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi)
+{
+	dsi_read(dsi, DSI_INT_ST0);
+	dsi_read(dsi, DSI_INT_ST1);
+	dsi_write(dsi, DSI_INT_MSK0, 0);
+	dsi_write(dsi, DSI_INT_MSK1, 0);
+}
+
+static void dw_mipi_dsi_bridge_disable(struct drm_bridge *bridge)
+{
+	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
+
+	if (dsi->dpms_mode != DRM_MODE_DPMS_ON)
+		return;
+
+	if (clk_enable(dsi->pclk)) {
+		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
+		return;
+	}
+
+	drm_panel_disable(dsi->panel);
+
+	/* Switch to dsi command mode for the panel de-initialization */
+	dw_mipi_dsi_set_mode(dsi, 0);
+	drm_panel_unprepare(dsi->panel);
+
+	dw_mipi_dsi_disable(dsi);
+	pm_runtime_put(dsi->dev);
+	clk_disable(dsi->pclk);
+	dsi->dpms_mode = DRM_MODE_DPMS_OFF;
+}
+
+static void dw_mipi_dsi_bridge_enable(struct drm_bridge *bridge)
+{
+	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
+	struct drm_encoder *encoder = bridge->encoder;
+	struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
+	const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
+	void *priv_data = dsi->plat_data->priv_data;
+	int ret;
+
+	if (dsi->dpms_mode == DRM_MODE_DPMS_ON)
+		return;
+
+	if (clk_enable(dsi->pclk)) {
+		dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
+		return;
+	}
+
+	ret = phy_ops->get_lane_mbps(priv_data, mode, dsi->mode_flags,
+				     dsi->lanes, dsi->format, &dsi->lane_mbps);
+	if (ret)
+		DRM_DEBUG_DRIVER("Phy get_lane_mbps() failed\n");
+
+	pm_runtime_get_sync(dsi->dev);
+	dw_mipi_dsi_init(dsi);
+	dw_mipi_dsi_dpi_config(dsi, mode);
+	dw_mipi_dsi_packet_handler_config(dsi);
+	dw_mipi_dsi_video_mode_config(dsi);
+	dw_mipi_dsi_video_packet_config(dsi, mode);
+	dw_mipi_dsi_command_mode_config(dsi);
+	dw_mipi_dsi_line_timer_config(dsi, mode);
+	dw_mipi_dsi_vertical_timing_config(dsi, mode);
+
+	dw_mipi_dsi_dphy_init(dsi);
+	dw_mipi_dsi_dphy_timing_config(dsi);
+	dw_mipi_dsi_dphy_interface_config(dsi);
+
+	dw_mipi_dsi_clear_err(dsi);
+
+	ret = phy_ops->init(priv_data);
+	if (ret)
+		DRM_DEBUG_DRIVER("Phy init() failed\n");
+
+	dw_mipi_dsi_dphy_enable(dsi);
+
+	dw_mipi_dsi_wait_for_two_frames(mode);
+
+	/* Switch to dsi command mode for the panel initialization */
+	dw_mipi_dsi_set_mode(dsi, 0);
+	if (drm_panel_prepare(dsi->panel))
+		dev_err(dsi->dev, "failed to prepare panel\n");
+
+	/* Switch to dsi video mode to send image data to the panel */
+	dw_mipi_dsi_set_mode(dsi, MIPI_DSI_MODE_VIDEO);
+	drm_panel_enable(dsi->panel);
+
+	clk_disable(dsi->pclk);
+
+	dsi->dpms_mode = DRM_MODE_DPMS_ON;
+}
+
+static int dw_mipi_dsi_connector_get_modes(struct drm_connector *connector)
+{
+	struct dw_mipi_dsi *dsi = con_to_dsi(connector);
+
+	return drm_panel_get_modes(dsi->panel);
+}
+
+static enum drm_mode_status
+dw_mipi_dsi_mode_valid(struct drm_connector *connector,
+		       struct drm_display_mode *mode)
+{
+	struct dw_mipi_dsi *dsi = con_to_dsi(connector);
+	const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data;
+	enum drm_mode_status mode_status = MODE_OK;
+
+	if (pdata->mode_valid)
+		mode_status = pdata->mode_valid(pdata->priv_data,
+						connector, mode);
+
+	return mode_status;
+}
+
+static struct drm_connector_helper_funcs dw_mipi_dsi_connector_helper_funcs = {
+	.get_modes = dw_mipi_dsi_connector_get_modes,
+	.mode_valid = dw_mipi_dsi_mode_valid,
+};
+
+static void dw_mipi_dsi_drm_connector_destroy(struct drm_connector *connector)
+{
+	drm_connector_unregister(connector);
+	drm_connector_cleanup(connector);
+}
+
+static const struct drm_connector_funcs dw_mipi_dsi_atomic_connector_funcs = {
+	.dpms = drm_atomic_helper_connector_dpms,
+	.fill_modes = drm_helper_probe_single_connector_modes,
+	.destroy = dw_mipi_dsi_drm_connector_destroy,
+	.reset = drm_atomic_helper_connector_reset,
+	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+static int dw_mipi_dsi_bridge_attach(struct drm_bridge *bridge)
+{
+	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
+	struct drm_connector *connector = &dsi->connector;
+
+	if (!bridge->encoder) {
+		DRM_ERROR("Parent encoder object not found\n");
+		return -ENODEV;
+	}
+
+	/* Set the encoder type as caller does not know it */
+	bridge->encoder->encoder_type = DRM_MODE_ENCODER_DSI;
+
+	connector->polled = DRM_CONNECTOR_POLL_HPD;
+
+	drm_connector_helper_add(connector,
+				 &dw_mipi_dsi_connector_helper_funcs);
+
+	drm_connector_init(bridge->dev, connector,
+			   &dw_mipi_dsi_atomic_connector_funcs,
+			   DRM_MODE_CONNECTOR_DSI);
+
+	drm_mode_connector_attach_encoder(connector, bridge->encoder);
+
+	return 0;
+}
+
+static struct drm_bridge_funcs dw_mipi_dsi_bridge_funcs = {
+	.enable = dw_mipi_dsi_bridge_enable,
+	.disable = dw_mipi_dsi_bridge_disable,
+	.attach = dw_mipi_dsi_bridge_attach,
+};
+
+static struct dw_mipi_dsi *
+__dw_mipi_dsi_probe(struct platform_device *pdev,
+		    const struct dw_mipi_dsi_plat_data *plat_data)
+{
+	struct device *dev = &pdev->dev;
+	struct reset_control *apb_rst;
+	struct dw_mipi_dsi *dsi;
+	struct resource *res;
+	int ret;
+
+	dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
+	if (!dsi)
+		return ERR_PTR(-ENOMEM);
+
+	dsi->dev = dev;
+	dsi->plat_data = plat_data;
+	dsi->dpms_mode = DRM_MODE_DPMS_OFF;
+
+	if (!plat_data->phy_ops->init || !plat_data->phy_ops->get_lane_mbps) {
+		DRM_ERROR("Phy not properly configured\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	if (!plat_data->base) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		if (!res)
+			return ERR_PTR(-ENODEV);
+
+		dsi->base = devm_ioremap_resource(dev, res);
+		if (IS_ERR(dsi->base))
+			return ERR_PTR(-ENODEV);
+
+	} else {
+		dsi->base = plat_data->base;
+	}
+
+	dsi->pclk = devm_clk_get(dev, "pclk");
+	if (IS_ERR(dsi->pclk)) {
+		ret = PTR_ERR(dsi->pclk);
+		dev_err(dev, "Unable to get pclk: %d\n", ret);
+		return ERR_PTR(ret);
+	}
+
+	/*
+	 * Note that the reset was not defined in the initial device tree, so
+	 * we have to be prepared for it not being found.
+	 */
+	apb_rst = devm_reset_control_get(dev, "apb");
+	if (IS_ERR(apb_rst)) {
+		ret = PTR_ERR(apb_rst);
+		if (ret == -ENOENT) {
+			apb_rst = NULL;
+		} else {
+			dev_err(dev, "Unable to get reset control: %d\n", ret);
+			return ERR_PTR(ret);
+		}
+	}
+
+	if (apb_rst) {
+		ret = clk_prepare_enable(dsi->pclk);
+		if (ret) {
+			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
+			return ERR_PTR(ret);
+		}
+
+		reset_control_assert(apb_rst);
+		usleep_range(10, 20);
+		reset_control_deassert(apb_rst);
+
+		clk_disable(dsi->pclk);
+	}
+
+	pm_runtime_enable(dev);
+
+	dsi->dsi_host.ops = &dw_mipi_dsi_host_ops;
+	dsi->dsi_host.dev = dev;
+	ret = mipi_dsi_host_register(&dsi->dsi_host);
+	if (ret) {
+		dev_err(dev, "Failed to register MIPI host: %d\n", ret);
+		return ERR_PTR(ret);
+	}
+
+	dsi->bridge.driver_private = dsi;
+	dsi->bridge.funcs = &dw_mipi_dsi_bridge_funcs;
+#ifdef CONFIG_OF
+	dsi->bridge.of_node = pdev->dev.of_node;
+#endif
+
+	clk_enable(dsi->pclk);
+
+	dev_set_drvdata(dev, dsi);
+
+	return dsi;
+}
+
+static void __dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi)
+{
+	pm_runtime_disable(dsi->dev);
+}
+
+/*
+ * Probe/remove API, used from platforms based on the DRM bridge API.
+ */
+int dw_mipi_dsi_probe(struct platform_device *pdev,
+		      const struct dw_mipi_dsi_plat_data *plat_data)
+{
+	struct dw_mipi_dsi *dsi;
+	int ret;
+
+	dsi = __dw_mipi_dsi_probe(pdev, plat_data);
+	if (IS_ERR(dsi))
+		return PTR_ERR(dsi);
+
+	ret = drm_bridge_add(&dsi->bridge);
+	if (ret < 0) {
+		__dw_mipi_dsi_remove(dsi);
+		return ret;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi_probe);
+
+void dw_mipi_dsi_remove(struct platform_device *pdev)
+{
+	struct dw_mipi_dsi *dsi = platform_get_drvdata(pdev);
+
+	mipi_dsi_host_unregister(&dsi->dsi_host);
+	drm_bridge_remove(&dsi->bridge);
+
+	__dw_mipi_dsi_remove(dsi);
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi_remove);
+
+/*
+ * Bind/unbind API, used from platforms based on the component framework.
+ */
+int dw_mipi_dsi_bind(struct platform_device *pdev, struct drm_encoder *encoder,
+		     const struct dw_mipi_dsi_plat_data *plat_data)
+{
+	struct dw_mipi_dsi *dsi;
+	int ret;
+
+	dsi = __dw_mipi_dsi_probe(pdev, plat_data);
+	if (IS_ERR(dsi))
+		return PTR_ERR(dsi);
+
+	ret = drm_bridge_attach(encoder, &dsi->bridge, NULL);
+	if (ret) {
+		dw_mipi_dsi_remove(pdev);
+		DRM_ERROR("Failed to initialize bridge with drm\n");
+		return ret;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi_bind);
+
+void dw_mipi_dsi_unbind(struct device *dev)
+{
+	struct dw_mipi_dsi *dsi = dev_get_drvdata(dev);
+
+	__dw_mipi_dsi_remove(dsi);
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi_unbind);
+
+MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
+MODULE_AUTHOR("Philippe Cornu <philippe.cornu@st.com>");
+MODULE_DESCRIPTION("DW MIPI DSI host controller driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:dw-mipi-dsi");
diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h
new file mode 100644
index 0000000..2043a37
--- /dev/null
+++ b/include/drm/bridge/dw_mipi_dsi.h
@@ -0,0 +1,42 @@ 
+/*
+ * Copyright (C) STMicroelectronics SA 2017
+ *
+ * Authors: Philippe Cornu <philippe.cornu@st.com>
+ *          Yannick Fertre <yannick.fertre@st.com>
+ *
+ * License terms:  GNU General Public License (GPL), version 2
+ */
+
+#ifndef __DW_MIPI_DSI__
+#define __DW_MIPI_DSI__
+
+#include <drm/drmP.h>
+
+struct dw_mipi_dsi_phy_ops {
+	int (*init)(void *priv_data);
+	int (*get_lane_mbps)(void *priv_data, struct drm_display_mode *mode,
+			     unsigned long mode_flags, u32 lanes, u32 format,
+			     unsigned int *lane_mbps);
+};
+
+struct dw_mipi_dsi_plat_data {
+	void __iomem *base;
+	unsigned int max_data_lanes;
+
+	enum drm_mode_status (*mode_valid)(void *priv_data,
+					   struct drm_connector *connector,
+					   struct drm_display_mode *mode);
+
+	const struct dw_mipi_dsi_phy_ops *phy_ops;
+
+	void *priv_data;
+};
+
+int dw_mipi_dsi_probe(struct platform_device *pdev,
+		      const struct dw_mipi_dsi_plat_data *plat_data);
+void dw_mipi_dsi_remove(struct platform_device *pdev);
+int dw_mipi_dsi_bind(struct platform_device *pdev, struct drm_encoder *encoder,
+		     const struct dw_mipi_dsi_plat_data *plat_data);
+void dw_mipi_dsi_unbind(struct device *dev);
+
+#endif /* __DW_MIPI_DSI__ */