@@ -603,6 +603,72 @@ static void dsi_encoder_enable(struct drm_encoder *encoder)
dsi->enable = true;
}
+static enum drm_mode_status dsi_encoder_phy_mode_valid(
+ struct drm_encoder *encoder,
+ const struct drm_display_mode *mode)
+{
+ struct dw_dsi *dsi = encoder_to_dsi(encoder);
+ struct mipi_phy_params phy;
+ u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+ u32 req_kHz, act_kHz, lane_byte_clk_kHz;
+
+ /* Calculate the lane byte clk using the adjusted mode clk */
+ memset(&phy, 0, sizeof(phy));
+ req_kHz = mode->clock * bpp / dsi->lanes;
+ act_kHz = dsi_calc_phy_rate(req_kHz, &phy);
+ lane_byte_clk_kHz = act_kHz / 8;
+
+ DRM_DEBUG_DRIVER("Checking mode %ix%i-%i@%i clock: %i...",
+ mode->hdisplay, mode->vdisplay, bpp,
+ drm_mode_vrefresh(mode), mode->clock);
+
+ /*
+ * Make sure the adjused mode clock and the lane byte clk
+ * have a common denominator base frequency
+ */
+ if (mode->clock/dsi->lanes == lane_byte_clk_kHz/3) {
+ DRM_DEBUG_DRIVER("OK!\n");
+ return MODE_OK;
+ }
+
+ DRM_DEBUG_DRIVER("BAD!\n");
+ return MODE_BAD;
+}
+
+static enum drm_mode_status dsi_encoder_mode_valid(struct drm_encoder *encoder,
+ const struct drm_display_mode *mode)
+
+{
+ const struct drm_crtc_helper_funcs *crtc_funcs = NULL;
+ struct drm_crtc *crtc = NULL;
+ struct drm_display_mode adj_mode;
+ enum drm_mode_status ret;
+
+ /*
+ * The crtc might adjust the mode, so go through the
+ * possible crtcs (technically just one) and call
+ * mode_fixup to figure out the adjusted mode before we
+ * validate it.
+ */
+ drm_for_each_crtc(crtc, encoder->dev) {
+ /*
+ * reset adj_mode to the mode value each time,
+ * so we don't adjust the mode twice
+ */
+ drm_mode_copy(&adj_mode, mode);
+
+ crtc_funcs = crtc->helper_private;
+ if (crtc_funcs && crtc_funcs->mode_fixup)
+ if (!crtc_funcs->mode_fixup(crtc, mode, &adj_mode))
+ return MODE_BAD;
+
+ ret = dsi_encoder_phy_mode_valid(encoder, &adj_mode);
+ if (ret != MODE_OK)
+ return ret;
+ }
+ return MODE_OK;
+}
+
static void dsi_encoder_mode_set(struct drm_encoder *encoder,
struct drm_display_mode *mode,
struct drm_display_mode *adj_mode)
@@ -622,6 +688,7 @@ static int dsi_encoder_atomic_check(struct drm_encoder *encoder,
static const struct drm_encoder_helper_funcs dw_encoder_helper_funcs = {
.atomic_check = dsi_encoder_atomic_check,
+ .mode_valid = dsi_encoder_mode_valid,
.mode_set = dsi_encoder_mode_set,
.enable = dsi_encoder_enable,
.disable = dsi_encoder_disable
@@ -178,6 +178,19 @@ static void ade_init(struct ade_hw_ctx *ctx)
FRM_END_START_MASK, REG_EFFECTIVE_IN_ADEEN_FRMEND);
}
+static bool ade_crtc_mode_fixup(struct drm_crtc *crtc,
+ const struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct ade_crtc *acrtc = to_ade_crtc(crtc);
+ struct ade_hw_ctx *ctx = acrtc->ctx;
+
+ adjusted_mode->clock =
+ clk_round_rate(ctx->ade_pix_clk, mode->clock * 1000) / 1000;
+ return true;
+}
+
+
static void ade_set_pix_clk(struct ade_hw_ctx *ctx,
struct drm_display_mode *mode,
struct drm_display_mode *adj_mode)
@@ -555,6 +568,7 @@ static void ade_crtc_atomic_flush(struct drm_crtc *crtc,
static const struct drm_crtc_helper_funcs ade_crtc_helper_funcs = {
.enable = ade_crtc_enable,
.disable = ade_crtc_disable,
+ .mode_fixup = ade_crtc_mode_fixup,
.mode_set_nofb = ade_crtc_mode_set_nofb,
.atomic_begin = ade_crtc_atomic_begin,
.atomic_flush = ade_crtc_atomic_flush,
Currently the hikey dsi logic cannot generate accurate byte clocks values for all pixel clock values. Thus if a mode clock is selected that cannot match the calculated byte clock, the device will boot with a blank screen. This patch uses the new mode_valid callback (many thanks to Jose Abreu for upstreaming it!) to ensure we don't select modes we cannot generate. Also, since the ade crtc code will adjust the mode in mode_set, this patch also adds a mode_fixup callback which we use to make sure we are validating the mode clock that will eventually be used. Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: David Airlie <airlied@linux.ie> Cc: Rob Clark <robdclark@gmail.com> Cc: Xinliang Liu <xinliang.liu@linaro.org> Cc: Xinliang Liu <z.liuxinliang@hisilicon.com> Cc: Rongrong Zou <zourongrong@gmail.com> Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com> Cc: Chen Feng <puck.chen@hisilicon.com> Cc: Jose Abreu <Jose.Abreu@synopsys.com> Cc: Archit Taneja <architt@codeaurora.org> Cc: dri-devel@lists.freedesktop.org Signed-off-by: John Stultz <john.stultz@linaro.org> --- v2: Reworked to calculate if modeclock matches the phy's byteclock, rather then using a whitelist of known modes. v3: Reworked to check across all possible crtcs (even though for us there is only one), and use mode_fixup instead of a custom function, as suggested by Jose and Daniel. v4: Fixes and improved error handling as suggested by Jose. --- drivers/gpu/drm/hisilicon/kirin/dw_drm_dsi.c | 67 +++++++++++++++++++++++++ drivers/gpu/drm/hisilicon/kirin/kirin_drm_ade.c | 14 ++++++ 2 files changed, 81 insertions(+)