diff mbox series

[RFC] drm/msm/disp/dpu1: add support for inline rotation in dpu driver

Message ID 1625311947-14114-1-git-send-email-kalyan_t@codeaurora.org (mailing list archive)
State New, archived
Headers show
Series [RFC] drm/msm/disp/dpu1: add support for inline rotation in dpu driver | expand

Commit Message

Kalyan Thota July 3, 2021, 11:32 a.m. UTC
Add inline rotation support in dpu driver. This change adds
rotation config for SC7280 target.

Change-Id: I15861dc03422274ffd823fc0fc2c1e47909bb22c
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
---
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c | 47 +++++++++----
 drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h | 20 ++++++
 drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c      | 93 ++++++++++++++++++++------
 drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h      |  2 +
 4 files changed, 128 insertions(+), 34 deletions(-)

Comments

Dmitry Baryshkov July 4, 2021, 9:59 a.m. UTC | #1
Hi,

Something is wrong with the threading, since this patch does not contain 
In-Reply-To header pointing to the cover letter? Could you please 
correct that? Using git-send-email --compose would allow you to write 
properly threaded cover letter.

On 03/07/2021 14:32, Kalyan Thota wrote:
> Add inline rotation support in dpu driver. This change adds
> rotation config for SC7280 target.

After spending some time reading display techpack, I think I'll ask you 
to add some summary to the patch summary, describing some bits and 
pieces. For example:

- Some DPU versions support inline rot90. It is supported only for 
limited amount of UBWC formats.
- There are two versions of inline rotators, v1 (present on sm8250 and 
sm7250) and v2 (sc7280). These versions differ in the list of supported 
formats and in the scaler possibilities.
- rot90 options are common to the rotation block version and do not 
depend on the SoC.

> 
> Change-Id: I15861dc03422274ffd823fc0fc2c1e47909bb22c

Please remove this

> Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
> ---
>   drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c | 47 +++++++++----
>   drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h | 20 ++++++
>   drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c      | 93 ++++++++++++++++++++------
>   drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h      |  2 +
>   4 files changed, 128 insertions(+), 34 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> index d01c4c9..45e4e56 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> @@ -25,6 +25,9 @@
>   #define VIG_SM8250_MASK \
>   	(VIG_MASK | BIT(DPU_SSPP_QOS_8LVL) | BIT(DPU_SSPP_SCALER_QSEED3LITE))
>   
> +#define VIG_SC7280_MASK \
> +	(VIG_SC7180_MASK | BIT(DPU_SSPP_INLINE_ROTATION))
> +
>   #define DMA_SDM845_MASK \
>   	(BIT(DPU_SSPP_SRC) | BIT(DPU_SSPP_QOS) | BIT(DPU_SSPP_QOS_8LVL) |\
>   	BIT(DPU_SSPP_TS_PREFILL) | BIT(DPU_SSPP_TS_PREFILL_REC1) |\
> @@ -102,6 +105,8 @@
>   #define MAX_DOWNSCALE_RATIO	4
>   #define SSPP_UNITY_SCALE	1
>   
> +#define INLINE_ROTATOR_V2	2
> +
>   #define STRCAT(X, Y) (X Y)
>   
>   static const uint32_t plane_formats[] = {
> @@ -177,6 +182,11 @@ static const uint32_t plane_formats_yuv[] = {
>   	DRM_FORMAT_YVU420,
>   };
>   
> +static const uint32_t rotation_formats[] = {

rotation_v2_formats?

> +	DRM_FORMAT_NV12,
> +	/* TODO add formats after validation */
> +};
> +
>   /*************************************************************
>    * DPU sub blocks config
>    *************************************************************/
> @@ -465,7 +475,16 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
>   
>   /* SSPP common configuration */
>   
> -#define _VIG_SBLK(num, sdma_pri, qseed_ver) \
> +static const struct dpu_rotation_cfg dpu_rot_cfg = {

dpu_rot_cfg is a bit too broad. dpu_rot_cfg_v2 seem to be more appropriate.


> +	.version = INLINE_ROTATOR_V2,

There are no check on the version, so you can drop this field.

> +	.rot_maxdwnscale_ratio_num = 1,
> +	.rot_maxdwnscale_ratio_dem = 1,

These don't seem to be used in your patch. Was the intent to avoid all 
the pre-downscale and downscale options? If so I'd suggest just 
enforcing the scale factor to 1 for now in the rot90 checking code.

 From reading the code I had the impression that for v2 downscaling up 
to 4:1 should be supported, so there is no need for special handling 
(VIG_SBLK already declared downscaling up to 4:1). V1 is different and 
will need limiting to 11:5. Is my understanding correct?

> +	.rot_maxheight = 1088,
> +	.rot_num_formats = ARRAY_SIZE(rotation_formats),
> +	.rot_format_list = rotation_formats,
> +};
> +
> +#define _VIG_SBLK(num, sdma_pri, qseed_ver, rot_cfg) \
>   	{ \
>   	.maxdwnscale = MAX_DOWNSCALE_RATIO, \
>   	.maxupscale = MAX_UPSCALE_RATIO, \
> @@ -482,6 +501,7 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
>   	.num_formats = ARRAY_SIZE(plane_formats_yuv), \
>   	.virt_format_list = plane_formats, \
>   	.virt_num_formats = ARRAY_SIZE(plane_formats), \
> +	.rotation_cfg = rot_cfg, \

At some point I thought about moving rot_cfg contents directly into the 
sblk config, but now I don't have a strong opinion on that. Let's keep 
it in the current way for now.

>   	}
>   
>   #define _DMA_SBLK(num, sdma_pri) \
> @@ -498,13 +518,13 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
>   	}
>   
>   static const struct dpu_sspp_sub_blks sdm845_vig_sblk_0 =
> -				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3);
> +				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3, 0);

NULL, not 0.

>   static const struct dpu_sspp_sub_blks sdm845_vig_sblk_1 =
> -				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3);
> +				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3, 0);
>   static const struct dpu_sspp_sub_blks sdm845_vig_sblk_2 =
> -				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3);
> +				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3, 0);
>   static const struct dpu_sspp_sub_blks sdm845_vig_sblk_3 =
> -				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3);
> +				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3, 0);
>   
>   static const struct dpu_sspp_sub_blks sdm845_dma_sblk_0 = _DMA_SBLK("8", 1);
>   static const struct dpu_sspp_sub_blks sdm845_dma_sblk_1 = _DMA_SBLK("9", 2);
> @@ -543,7 +563,10 @@ static const struct dpu_sspp_cfg sdm845_sspp[] = {
>   };
>   
>   static const struct dpu_sspp_sub_blks sc7180_vig_sblk_0 =
> -				_VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4);
> +				_VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4, 0);

And here.

> +
> +static const struct dpu_sspp_sub_blks sc7280_vig_sblk_0 =
> +				_VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4, &dpu_rot_cfg);
>   
>   static const struct dpu_sspp_cfg sc7180_sspp[] = {
>   	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7180_MASK,
> @@ -557,13 +580,13 @@ static const struct dpu_sspp_cfg sc7180_sspp[] = {
>   };
>   
>   static const struct dpu_sspp_sub_blks sm8250_vig_sblk_0 =
> -				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3LITE);
> +				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3LITE, 0);
>   static const struct dpu_sspp_sub_blks sm8250_vig_sblk_1 =
> -				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3LITE);
> +				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3LITE, 0);
>   static const struct dpu_sspp_sub_blks sm8250_vig_sblk_2 =
> -				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3LITE);
> +				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3LITE, 0);
>   static const struct dpu_sspp_sub_blks sm8250_vig_sblk_3 =
> -				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3LITE);
> +				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3LITE, 0);

And here

>   
>   static const struct dpu_sspp_cfg sm8250_sspp[] = {
>   	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SM8250_MASK,
> @@ -585,8 +608,8 @@ static const struct dpu_sspp_cfg sm8250_sspp[] = {
>   };
>   
>   static const struct dpu_sspp_cfg sc7280_sspp[] = {
> -	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7180_MASK,
> -		sc7180_vig_sblk_0, 0,  SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
> +	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7280_MASK,
> +		sc7280_vig_sblk_0, 0,  SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
>   	SSPP_BLK("sspp_8", SSPP_DMA0, 0x24000,  DMA_SDM845_MASK,
>   		sdm845_dma_sblk_0, 1, SSPP_TYPE_DMA, DPU_CLK_CTRL_DMA0),
>   	SSPP_BLK("sspp_9", SSPP_DMA1, 0x26000,  DMA_CURSOR_SDM845_MASK,
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> index d2a945a..8421001 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> @@ -129,6 +129,7 @@ enum {
>   	DPU_SSPP_TS_PREFILL,
>   	DPU_SSPP_TS_PREFILL_REC1,
>   	DPU_SSPP_CDP,
> +	DPU_SSPP_INLINE_ROTATION,
>   	DPU_SSPP_MAX
>   };
>   
> @@ -309,6 +310,24 @@ struct dpu_qos_lut_tbl {
>   };
>   
>   /**
> + * struct dpu_rotation_cfg - define inline rotation config
> + * @version: Inline rotation version
> + * @rot_maxdwnscale_ratio_num: max downscale ratio for rotation numerator
> + * @rot_maxdwnscale_ratio_dem: max downscale ratio for denominator
> + * @rot_maxheight: max pre rotated height allowed for rotation
> + * @rot_num_formats: count of the formats
> + * @rot_format_list: list of supported rotator formats
> + */
> +struct dpu_rotation_cfg {
> +	u32 version;
> +	u32 rot_maxdwnscale_ratio_num;
> +	u32 rot_maxdwnscale_ratio_dem;
> +	u32 rot_maxheight;
> +	u32 rot_num_formats;
> +	const u32 *rot_format_list;
> +};
> +
> +/**
>    * struct dpu_caps - define DPU capabilities
>    * @max_mixer_width    max layer mixer line width support.
>    * @max_mixer_blendstages max layer mixer blend stages or
> @@ -384,6 +403,7 @@ struct dpu_sspp_sub_blks {
>   	u32 num_formats;
>   	const u32 *virt_format_list;
>   	u32 virt_num_formats;
> +	const struct dpu_rotation_cfg *rotation_cfg;
>   };
>   
>   /**
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> index ec4a6f0..0daee63 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> @@ -539,16 +539,28 @@ static void _dpu_plane_set_scanout(struct drm_plane *plane,
>   
>   static void _dpu_plane_setup_scaler3(struct dpu_plane *pdpu,
>   		struct dpu_plane_state *pstate,
> -		uint32_t src_w, uint32_t src_h, uint32_t dst_w, uint32_t dst_h,
>   		struct dpu_hw_scaler3_cfg *scale_cfg,
>   		const struct dpu_format *fmt,
>   		uint32_t chroma_subsmpl_h, uint32_t chroma_subsmpl_v)
>   {
>   	uint32_t i;
> +	bool inline_rotation = (pstate->rotation & DRM_MODE_ROTATE_90);
> +	uint32_t src_w = drm_rect_width(&pdpu->pipe_cfg.src_rect);
> +	uint32_t src_h = drm_rect_height(&pdpu->pipe_cfg.src_rect);
> +	uint32_t dst_w = drm_rect_width(&pdpu->pipe_cfg.dst_rect);
> +	uint32_t dst_h = drm_rect_height(&pdpu->pipe_cfg.dst_rect);
>   
>   	memset(scale_cfg, 0, sizeof(*scale_cfg));
>   	memset(&pstate->pixel_ext, 0, sizeof(struct dpu_hw_pixel_ext));
>   
> +	/*
> +	 * For inline rotation cases, scaler config is post-rotation,
> +	 * so swap the dimensions here. However, pixel extension will
> +	 * need pre-rotation settings.
> +	 */
> +	if (inline_rotation)
> +		swap(src_w, src_h);
> +
>   	scale_cfg->phase_step_x[DPU_SSPP_COMP_0] =
>   		mult_frac((1 << PHASE_STEP_SHIFT), src_w, dst_w);
>   	scale_cfg->phase_step_y[DPU_SSPP_COMP_0] =
> @@ -587,10 +599,10 @@ static void _dpu_plane_setup_scaler3(struct dpu_plane *pdpu,
>   			scale_cfg->preload_y[i] = DPU_QSEED3_DEFAULT_PRELOAD_V;
>   		}
>   
> -		pstate->pixel_ext.num_ext_pxls_top[i] =
> -			scale_cfg->src_height[i];
> -		pstate->pixel_ext.num_ext_pxls_left[i] =
> -			scale_cfg->src_width[i];
> +		pstate->pixel_ext.num_ext_pxls_top[i] = inline_rotation ?
> +			scale_cfg->src_width[i] : scale_cfg->src_height[i];
> +		pstate->pixel_ext.num_ext_pxls_left[i] = inline_rotation ?
> +	

Just move pixel_ext setup outside of dpu_setup_scaler3.

Then you can pass different src_w/src_h pairs to pixel_ext setup and 
scale_cfg setup code.

		scale_cfg->src_height[i] : scale_cfg->src_width[i];
>   	}
>   	if (!(DPU_FORMAT_IS_YUV(fmt)) && (src_h == dst_h)
>   		&& (src_w == dst_w))
> @@ -662,10 +674,6 @@ static void _dpu_plane_setup_scaler(struct dpu_plane *pdpu,
>   	/* don't chroma subsample if decimating */
>   	/* update scaler. calculate default config for QSEED3 */
>   	_dpu_plane_setup_scaler3(pdpu, pstate,
> -			drm_rect_width(&pdpu->pipe_cfg.src_rect),
> -			drm_rect_height(&pdpu->pipe_cfg.src_rect),
> -			drm_rect_width(&pdpu->pipe_cfg.dst_rect),
> -			drm_rect_height(&pdpu->pipe_cfg.dst_rect),
>   			&pstate->scaler3_cfg, fmt,
>   			info->hsub, info->vsub);
>   }
> @@ -959,6 +967,7 @@ static int dpu_plane_atomic_check(struct drm_plane *plane,
>   	const struct dpu_format *fmt;
>   	struct drm_rect src, dst, fb_rect = { 0 };
>   	uint32_t min_src_size, max_linewidth;
> +	unsigned int rotation;
>   
>   	if (new_plane_state->crtc)
>   		crtc_state = drm_atomic_get_new_crtc_state(state,
> @@ -1028,6 +1037,48 @@ static int dpu_plane_atomic_check(struct drm_plane *plane,
>   		return -E2BIG;
>   	}
>   
> +	rotation = drm_rotation_simplify(new_plane_state->rotation,
> +			    DRM_MODE_ROTATE_0 |
> +			    DRM_MODE_ROTATE_90 |
> +			    DRM_MODE_REFLECT_X |
> +			    DRM_MODE_REFLECT_Y);
> +
> +	if (rotation & DRM_MODE_ROTATE_90) {
> +		struct msm_drm_private *priv = plane->dev->dev_private;
> +		struct dpu_kms *dpu_kms;
> +		const struct msm_format *msm_fmt;
> +		const struct dpu_format *fmt;
> +		bool found = false;
> +		u32 i, num_formats;
> +		const u32 *supported_formats;
> +
> +		if (src.y2 > pdpu->pipe_sblk->rotation_cfg->rot_maxheight) {

Check that rotation_cfg is not null and that we have 
DPU_SSPP_INLINE_ROTATION here.

> +			DPU_DEBUG_PLANE(pdpu,
> +			"invalid height for inline rot:%d max:%d\n",
> +			src.y2, pdpu->pipe_sblk->rotation_cfg->rot_maxheight);
> +			return -EINVAL;
> +		}
> +
> +		/* check for valid formats supported by inline rotation */
> +		dpu_kms = to_dpu_kms(priv->kms);

Nit: you don't need kms here.

> +		msm_fmt = msm_framebuffer_format(new_plane_state->fb);
> +		fmt = to_dpu_format(msm_fmt);
> +		supported_formats = pdpu->pipe_sblk->rotation_cfg->rot_format_list;
> +		num_formats = pdpu->pipe_sblk->rotation_cfg->rot_num_formats;
> +
> +		for (i = 0; i < num_formats; i++) {
> +			if (fmt->base.pixel_format == supported_formats[i] &&
> +				fmt->fetch_mode == DPU_FETCH_UBWC)

I think you'd like to use DPU_FORMAT_IS_UBWC here.

> +				found = true;
> +		}
> +
> +		if (!found || !num_formats) {
> +			DPU_DEBUG_PLANE(pdpu,
> +			"supported_format not found num:%d\n", num_formats);
> +			return -EINVAL;
> +		}
> +	}
> +	pstate->rotation = rotation;
>   	pstate->needs_qos_remap = drm_atomic_crtc_needs_modeset(crtc_state);
>   
>   	return 0;
> @@ -1153,21 +1204,18 @@ static void dpu_plane_sspp_atomic_update(struct drm_plane *plane)
>   				pstate->multirect_mode);
>   
>   	if (pdpu->pipe_hw->ops.setup_format) {
> -		unsigned int rotation;
>   
>   		src_flags = 0x0;
>   
> -		rotation = drm_rotation_simplify(state->rotation,
> -						 DRM_MODE_ROTATE_0 |
> -						 DRM_MODE_REFLECT_X |
> -						 DRM_MODE_REFLECT_Y);
> -
> -		if (rotation & DRM_MODE_REFLECT_X)
> +		if (pstate->rotation & DRM_MODE_REFLECT_X)
>   			src_flags |= DPU_SSPP_FLIP_LR;
>   
> -		if (rotation & DRM_MODE_REFLECT_Y)
> +		if (pstate->rotation & DRM_MODE_REFLECT_Y)
>   			src_flags |= DPU_SSPP_FLIP_UD;
>   
> +		if (pstate->rotation & DRM_MODE_ROTATE_90)
> +			src_flags |= DPU_SSPP_ROT_90;
> +
>   		/* update format */
>   		pdpu->pipe_hw->ops.setup_format(pdpu->pipe_hw, fmt, src_flags,
>   				pstate->multirect_index);
> @@ -1578,6 +1626,8 @@ struct drm_plane *dpu_plane_init(struct drm_device *dev,
>   	int zpos_max = DPU_ZPOS_MAX;
>   	uint32_t num_formats;
>   	int ret = -EINVAL;
> +	unsigned int supported_rotations = DRM_MODE_ROTATE_0 |
> +			DRM_MODE_ROTATE_180 | DRM_MODE_REFLECT_X | DRM_MODE_REFLECT_Y;
>   
>   	/* create and zero local structure */
>   	pdpu = kzalloc(sizeof(*pdpu), GFP_KERNEL);
> @@ -1647,12 +1697,11 @@ struct drm_plane *dpu_plane_init(struct drm_device *dev,
>   	if (ret)
>   		DPU_ERROR("failed to install zpos property, rc = %d\n", ret);
>   
> +	if (pdpu->features & BIT(DPU_SSPP_INLINE_ROTATION))
> +		supported_rotations |= DRM_MODE_ROTATE_90;

And ROTATE_270 too please.

> +
>   	drm_plane_create_rotation_property(plane,
> -			DRM_MODE_ROTATE_0,
> -			DRM_MODE_ROTATE_0 |
> -			DRM_MODE_ROTATE_180 |
> -			DRM_MODE_REFLECT_X |
> -			DRM_MODE_REFLECT_Y);
> +		    DRM_MODE_ROTATE_0, supported_rotations);
>   
>   	drm_plane_enable_fb_damage_clips(plane);
>   
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> index 34e03ac..16ec8dc 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> @@ -28,6 +28,7 @@
>    * @cdp_cfg:	CDP configuration
>    * @plane_fetch_bw: calculated BW per plane
>    * @plane_clk: calculated clk per plane
> + * @rotation: simplified drm rotation hint
>    */
>   struct dpu_plane_state {
>   	struct drm_plane_state base;
> @@ -45,6 +46,7 @@ struct dpu_plane_state {
>   	struct dpu_hw_pipe_cdp_cfg cdp_cfg;
>   	u64 plane_fetch_bw;
>   	u64 plane_clk;
> +	unsigned int rotation;
>   };
>   
>   /**
>
Dmitry Baryshkov July 4, 2021, 11:20 a.m. UTC | #2
On 03/07/2021 14:32, Kalyan Thota wrote:
> Add inline rotation support in dpu driver. This change adds
> rotation config for SC7280 target.
> 
> Change-Id: I15861dc03422274ffd823fc0fc2c1e47909bb22c
> Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
> ---
>   drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c | 47 +++++++++----
>   drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h | 20 ++++++
>   drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c      | 93 ++++++++++++++++++++------
>   drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h      |  2 +
>   4 files changed, 128 insertions(+), 34 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> index d01c4c9..45e4e56 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> @@ -25,6 +25,9 @@
>   #define VIG_SM8250_MASK \
>   	(VIG_MASK | BIT(DPU_SSPP_QOS_8LVL) | BIT(DPU_SSPP_SCALER_QSEED3LITE))
>   
> +#define VIG_SC7280_MASK \
> +	(VIG_SC7180_MASK | BIT(DPU_SSPP_INLINE_ROTATION))
> +
>   #define DMA_SDM845_MASK \
>   	(BIT(DPU_SSPP_SRC) | BIT(DPU_SSPP_QOS) | BIT(DPU_SSPP_QOS_8LVL) |\
>   	BIT(DPU_SSPP_TS_PREFILL) | BIT(DPU_SSPP_TS_PREFILL_REC1) |\
> @@ -102,6 +105,8 @@
>   #define MAX_DOWNSCALE_RATIO	4
>   #define SSPP_UNITY_SCALE	1
>   
> +#define INLINE_ROTATOR_V2	2
> +
>   #define STRCAT(X, Y) (X Y)
>   
>   static const uint32_t plane_formats[] = {
> @@ -177,6 +182,11 @@ static const uint32_t plane_formats_yuv[] = {
>   	DRM_FORMAT_YVU420,
>   };
>   
> +static const uint32_t rotation_formats[] = {
> +	DRM_FORMAT_NV12,
> +	/* TODO add formats after validation */
> +};
> +
>   /*************************************************************
>    * DPU sub blocks config
>    *************************************************************/
> @@ -465,7 +475,16 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
>   
>   /* SSPP common configuration */
>   
> -#define _VIG_SBLK(num, sdma_pri, qseed_ver) \
> +static const struct dpu_rotation_cfg dpu_rot_cfg = {
> +	.version = INLINE_ROTATOR_V2,
> +	.rot_maxdwnscale_ratio_num = 1,
> +	.rot_maxdwnscale_ratio_dem = 1,
> +	.rot_maxheight = 1088,
> +	.rot_num_formats = ARRAY_SIZE(rotation_formats),
> +	.rot_format_list = rotation_formats,
> +};
> +
> +#define _VIG_SBLK(num, sdma_pri, qseed_ver, rot_cfg) \
>   	{ \
>   	.maxdwnscale = MAX_DOWNSCALE_RATIO, \
>   	.maxupscale = MAX_UPSCALE_RATIO, \
> @@ -482,6 +501,7 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
>   	.num_formats = ARRAY_SIZE(plane_formats_yuv), \
>   	.virt_format_list = plane_formats, \
>   	.virt_num_formats = ARRAY_SIZE(plane_formats), \
> +	.rotation_cfg = rot_cfg, \
>   	}
>   
>   #define _DMA_SBLK(num, sdma_pri) \
> @@ -498,13 +518,13 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
>   	}
>   
>   static const struct dpu_sspp_sub_blks sdm845_vig_sblk_0 =
> -				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3);
> +				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3, 0);
>   static const struct dpu_sspp_sub_blks sdm845_vig_sblk_1 =
> -				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3);
> +				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3, 0);
>   static const struct dpu_sspp_sub_blks sdm845_vig_sblk_2 =
> -				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3);
> +				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3, 0);
>   static const struct dpu_sspp_sub_blks sdm845_vig_sblk_3 =
> -				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3);
> +				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3, 0);
>   
>   static const struct dpu_sspp_sub_blks sdm845_dma_sblk_0 = _DMA_SBLK("8", 1);
>   static const struct dpu_sspp_sub_blks sdm845_dma_sblk_1 = _DMA_SBLK("9", 2);
> @@ -543,7 +563,10 @@ static const struct dpu_sspp_cfg sdm845_sspp[] = {
>   };
>   
>   static const struct dpu_sspp_sub_blks sc7180_vig_sblk_0 =
> -				_VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4);
> +				_VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4, 0);
> +
> +static const struct dpu_sspp_sub_blks sc7280_vig_sblk_0 =
> +				_VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4, &dpu_rot_cfg);
>   
>   static const struct dpu_sspp_cfg sc7180_sspp[] = {
>   	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7180_MASK,
> @@ -557,13 +580,13 @@ static const struct dpu_sspp_cfg sc7180_sspp[] = {
>   };
>   
>   static const struct dpu_sspp_sub_blks sm8250_vig_sblk_0 =
> -				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3LITE);
> +				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3LITE, 0);
>   static const struct dpu_sspp_sub_blks sm8250_vig_sblk_1 =
> -				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3LITE);
> +				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3LITE, 0);
>   static const struct dpu_sspp_sub_blks sm8250_vig_sblk_2 =
> -				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3LITE);
> +				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3LITE, 0);
>   static const struct dpu_sspp_sub_blks sm8250_vig_sblk_3 =
> -				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3LITE);
> +				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3LITE, 0);
>   
>   static const struct dpu_sspp_cfg sm8250_sspp[] = {
>   	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SM8250_MASK,
> @@ -585,8 +608,8 @@ static const struct dpu_sspp_cfg sm8250_sspp[] = {
>   };
>   
>   static const struct dpu_sspp_cfg sc7280_sspp[] = {
> -	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7180_MASK,
> -		sc7180_vig_sblk_0, 0,  SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
> +	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7280_MASK,
> +		sc7280_vig_sblk_0, 0,  SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
>   	SSPP_BLK("sspp_8", SSPP_DMA0, 0x24000,  DMA_SDM845_MASK,
>   		sdm845_dma_sblk_0, 1, SSPP_TYPE_DMA, DPU_CLK_CTRL_DMA0),
>   	SSPP_BLK("sspp_9", SSPP_DMA1, 0x26000,  DMA_CURSOR_SDM845_MASK,
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> index d2a945a..8421001 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> @@ -129,6 +129,7 @@ enum {
>   	DPU_SSPP_TS_PREFILL,
>   	DPU_SSPP_TS_PREFILL_REC1,
>   	DPU_SSPP_CDP,
> +	DPU_SSPP_INLINE_ROTATION,
>   	DPU_SSPP_MAX
>   };
>   
> @@ -309,6 +310,24 @@ struct dpu_qos_lut_tbl {
>   };
>   
>   /**
> + * struct dpu_rotation_cfg - define inline rotation config
> + * @version: Inline rotation version
> + * @rot_maxdwnscale_ratio_num: max downscale ratio for rotation numerator
> + * @rot_maxdwnscale_ratio_dem: max downscale ratio for denominator
> + * @rot_maxheight: max pre rotated height allowed for rotation
> + * @rot_num_formats: count of the formats
> + * @rot_format_list: list of supported rotator formats
> + */
> +struct dpu_rotation_cfg {
> +	u32 version;
> +	u32 rot_maxdwnscale_ratio_num;
> +	u32 rot_maxdwnscale_ratio_dem;
> +	u32 rot_maxheight;
> +	u32 rot_num_formats;
> +	const u32 *rot_format_list;
> +};
> +
> +/**
>    * struct dpu_caps - define DPU capabilities
>    * @max_mixer_width    max layer mixer line width support.
>    * @max_mixer_blendstages max layer mixer blend stages or
> @@ -384,6 +403,7 @@ struct dpu_sspp_sub_blks {
>   	u32 num_formats;
>   	const u32 *virt_format_list;
>   	u32 virt_num_formats;
> +	const struct dpu_rotation_cfg *rotation_cfg;
>   };
>   
>   /**
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> index ec4a6f0..0daee63 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> @@ -539,16 +539,28 @@ static void _dpu_plane_set_scanout(struct drm_plane *plane,
>   
>   static void _dpu_plane_setup_scaler3(struct dpu_plane *pdpu,
>   		struct dpu_plane_state *pstate,
> -		uint32_t src_w, uint32_t src_h, uint32_t dst_w, uint32_t dst_h,
>   		struct dpu_hw_scaler3_cfg *scale_cfg,
>   		const struct dpu_format *fmt,
>   		uint32_t chroma_subsmpl_h, uint32_t chroma_subsmpl_v)
>   {
>   	uint32_t i;
> +	bool inline_rotation = (pstate->rotation & DRM_MODE_ROTATE_90);
> +	uint32_t src_w = drm_rect_width(&pdpu->pipe_cfg.src_rect);
> +	uint32_t src_h = drm_rect_height(&pdpu->pipe_cfg.src_rect);
> +	uint32_t dst_w = drm_rect_width(&pdpu->pipe_cfg.dst_rect);
> +	uint32_t dst_h = drm_rect_height(&pdpu->pipe_cfg.dst_rect);
>   
>   	memset(scale_cfg, 0, sizeof(*scale_cfg));
>   	memset(&pstate->pixel_ext, 0, sizeof(struct dpu_hw_pixel_ext));
>   
> +	/*
> +	 * For inline rotation cases, scaler config is post-rotation,
> +	 * so swap the dimensions here. However, pixel extension will
> +	 * need pre-rotation settings.
> +	 */
> +	if (inline_rotation)
> +		swap(src_w, src_h);
> +
>   	scale_cfg->phase_step_x[DPU_SSPP_COMP_0] =
>   		mult_frac((1 << PHASE_STEP_SHIFT), src_w, dst_w);
>   	scale_cfg->phase_step_y[DPU_SSPP_COMP_0] =
> @@ -587,10 +599,10 @@ static void _dpu_plane_setup_scaler3(struct dpu_plane *pdpu,
>   			scale_cfg->preload_y[i] = DPU_QSEED3_DEFAULT_PRELOAD_V;
>   		}
>   
> -		pstate->pixel_ext.num_ext_pxls_top[i] =
> -			scale_cfg->src_height[i];
> -		pstate->pixel_ext.num_ext_pxls_left[i] =
> -			scale_cfg->src_width[i];
> +		pstate->pixel_ext.num_ext_pxls_top[i] = inline_rotation ?
> +			scale_cfg->src_width[i] : scale_cfg->src_height[i];
> +		pstate->pixel_ext.num_ext_pxls_left[i] = inline_rotation ?
> +			scale_cfg->src_height[i] : scale_cfg->src_width[i];
>   	}
>   	if (!(DPU_FORMAT_IS_YUV(fmt)) && (src_h == dst_h)
>   		&& (src_w == dst_w))
> @@ -662,10 +674,6 @@ static void _dpu_plane_setup_scaler(struct dpu_plane *pdpu,
>   	/* don't chroma subsample if decimating */
>   	/* update scaler. calculate default config for QSEED3 */
>   	_dpu_plane_setup_scaler3(pdpu, pstate,
> -			drm_rect_width(&pdpu->pipe_cfg.src_rect),
> -			drm_rect_height(&pdpu->pipe_cfg.src_rect),
> -			drm_rect_width(&pdpu->pipe_cfg.dst_rect),
> -			drm_rect_height(&pdpu->pipe_cfg.dst_rect),
>   			&pstate->scaler3_cfg, fmt,
>   			info->hsub, info->vsub);
>   }
> @@ -959,6 +967,7 @@ static int dpu_plane_atomic_check(struct drm_plane *plane,
>   	const struct dpu_format *fmt;
>   	struct drm_rect src, dst, fb_rect = { 0 };
>   	uint32_t min_src_size, max_linewidth;
> +	unsigned int rotation;
>   
>   	if (new_plane_state->crtc)
>   		crtc_state = drm_atomic_get_new_crtc_state(state,
> @@ -1028,6 +1037,48 @@ static int dpu_plane_atomic_check(struct drm_plane *plane,
>   		return -E2BIG;
>   	}
>   
> +	rotation = drm_rotation_simplify(new_plane_state->rotation,
> +			    DRM_MODE_ROTATE_0 |
> +			    DRM_MODE_ROTATE_90 |
> +			    DRM_MODE_REFLECT_X |
> +			    DRM_MODE_REFLECT_Y);
> +
> +	if (rotation & DRM_MODE_ROTATE_90) {
> +		struct msm_drm_private *priv = plane->dev->dev_private;
> +		struct dpu_kms *dpu_kms;
> +		const struct msm_format *msm_fmt;
> +		const struct dpu_format *fmt;
> +		bool found = false;
> +		u32 i, num_formats;
> +		const u32 *supported_formats;
> +
> +		if (src.y2 > pdpu->pipe_sblk->rotation_cfg->rot_maxheight) {

Another note: drm_rect_width(&src) rather than src.y2 here.

> +			DPU_DEBUG_PLANE(pdpu,
> +			"invalid height for inline rot:%d max:%d\n",
> +			src.y2, pdpu->pipe_sblk->rotation_cfg->rot_maxheight);
> +			return -EINVAL;
> +		}
> +
> +		/* check for valid formats supported by inline rotation */
> +		dpu_kms = to_dpu_kms(priv->kms);
> +		msm_fmt = msm_framebuffer_format(new_plane_state->fb);
> +		fmt = to_dpu_format(msm_fmt);
> +		supported_formats = pdpu->pipe_sblk->rotation_cfg->rot_format_list;
> +		num_formats = pdpu->pipe_sblk->rotation_cfg->rot_num_formats;
> +
> +		for (i = 0; i < num_formats; i++) {
> +			if (fmt->base.pixel_format == supported_formats[i] &&
> +				fmt->fetch_mode == DPU_FETCH_UBWC)
> +				found = true;
> +		}
> +
> +		if (!found || !num_formats) {
> +			DPU_DEBUG_PLANE(pdpu,
> +			"supported_format not found num:%d\n", num_formats);
> +			return -EINVAL;
> +		}
> +	}
> +	pstate->rotation = rotation;
>   	pstate->needs_qos_remap = drm_atomic_crtc_needs_modeset(crtc_state);
>   
>   	return 0;
> @@ -1153,21 +1204,18 @@ static void dpu_plane_sspp_atomic_update(struct drm_plane *plane)
>   				pstate->multirect_mode);
>   
>   	if (pdpu->pipe_hw->ops.setup_format) {
> -		unsigned int rotation;
>   
>   		src_flags = 0x0;
>   
> -		rotation = drm_rotation_simplify(state->rotation,
> -						 DRM_MODE_ROTATE_0 |
> -						 DRM_MODE_REFLECT_X |
> -						 DRM_MODE_REFLECT_Y);
> -
> -		if (rotation & DRM_MODE_REFLECT_X)
> +		if (pstate->rotation & DRM_MODE_REFLECT_X)
>   			src_flags |= DPU_SSPP_FLIP_LR;
>   
> -		if (rotation & DRM_MODE_REFLECT_Y)
> +		if (pstate->rotation & DRM_MODE_REFLECT_Y)
>   			src_flags |= DPU_SSPP_FLIP_UD;
>   
> +		if (pstate->rotation & DRM_MODE_ROTATE_90)
> +			src_flags |= DPU_SSPP_ROT_90;
> +
>   		/* update format */
>   		pdpu->pipe_hw->ops.setup_format(pdpu->pipe_hw, fmt, src_flags,
>   				pstate->multirect_index);
> @@ -1578,6 +1626,8 @@ struct drm_plane *dpu_plane_init(struct drm_device *dev,
>   	int zpos_max = DPU_ZPOS_MAX;
>   	uint32_t num_formats;
>   	int ret = -EINVAL;
> +	unsigned int supported_rotations = DRM_MODE_ROTATE_0 |
> +			DRM_MODE_ROTATE_180 | DRM_MODE_REFLECT_X | DRM_MODE_REFLECT_Y;
>   
>   	/* create and zero local structure */
>   	pdpu = kzalloc(sizeof(*pdpu), GFP_KERNEL);
> @@ -1647,12 +1697,11 @@ struct drm_plane *dpu_plane_init(struct drm_device *dev,
>   	if (ret)
>   		DPU_ERROR("failed to install zpos property, rc = %d\n", ret);
>   
> +	if (pdpu->features & BIT(DPU_SSPP_INLINE_ROTATION))
> +		supported_rotations |= DRM_MODE_ROTATE_90;
> +
>   	drm_plane_create_rotation_property(plane,
> -			DRM_MODE_ROTATE_0,
> -			DRM_MODE_ROTATE_0 |
> -			DRM_MODE_ROTATE_180 |
> -			DRM_MODE_REFLECT_X |
> -			DRM_MODE_REFLECT_Y);
> +		    DRM_MODE_ROTATE_0, supported_rotations);
>   
>   	drm_plane_enable_fb_damage_clips(plane);
>   
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> index 34e03ac..16ec8dc 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> @@ -28,6 +28,7 @@
>    * @cdp_cfg:	CDP configuration
>    * @plane_fetch_bw: calculated BW per plane
>    * @plane_clk: calculated clk per plane
> + * @rotation: simplified drm rotation hint
>    */
>   struct dpu_plane_state {
>   	struct drm_plane_state base;
> @@ -45,6 +46,7 @@ struct dpu_plane_state {
>   	struct dpu_hw_pipe_cdp_cfg cdp_cfg;
>   	u64 plane_fetch_bw;
>   	u64 plane_clk;
> +	unsigned int rotation;
>   };
>   
>   /**
>
diff mbox series

Patch

diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
index d01c4c9..45e4e56 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
@@ -25,6 +25,9 @@ 
 #define VIG_SM8250_MASK \
 	(VIG_MASK | BIT(DPU_SSPP_QOS_8LVL) | BIT(DPU_SSPP_SCALER_QSEED3LITE))
 
+#define VIG_SC7280_MASK \
+	(VIG_SC7180_MASK | BIT(DPU_SSPP_INLINE_ROTATION))
+
 #define DMA_SDM845_MASK \
 	(BIT(DPU_SSPP_SRC) | BIT(DPU_SSPP_QOS) | BIT(DPU_SSPP_QOS_8LVL) |\
 	BIT(DPU_SSPP_TS_PREFILL) | BIT(DPU_SSPP_TS_PREFILL_REC1) |\
@@ -102,6 +105,8 @@ 
 #define MAX_DOWNSCALE_RATIO	4
 #define SSPP_UNITY_SCALE	1
 
+#define INLINE_ROTATOR_V2	2
+
 #define STRCAT(X, Y) (X Y)
 
 static const uint32_t plane_formats[] = {
@@ -177,6 +182,11 @@  static const uint32_t plane_formats_yuv[] = {
 	DRM_FORMAT_YVU420,
 };
 
+static const uint32_t rotation_formats[] = {
+	DRM_FORMAT_NV12,
+	/* TODO add formats after validation */
+};
+
 /*************************************************************
  * DPU sub blocks config
  *************************************************************/
@@ -465,7 +475,16 @@  static const struct dpu_ctl_cfg sc7280_ctl[] = {
 
 /* SSPP common configuration */
 
-#define _VIG_SBLK(num, sdma_pri, qseed_ver) \
+static const struct dpu_rotation_cfg dpu_rot_cfg = {
+	.version = INLINE_ROTATOR_V2,
+	.rot_maxdwnscale_ratio_num = 1,
+	.rot_maxdwnscale_ratio_dem = 1,
+	.rot_maxheight = 1088,
+	.rot_num_formats = ARRAY_SIZE(rotation_formats),
+	.rot_format_list = rotation_formats,
+};
+
+#define _VIG_SBLK(num, sdma_pri, qseed_ver, rot_cfg) \
 	{ \
 	.maxdwnscale = MAX_DOWNSCALE_RATIO, \
 	.maxupscale = MAX_UPSCALE_RATIO, \
@@ -482,6 +501,7 @@  static const struct dpu_ctl_cfg sc7280_ctl[] = {
 	.num_formats = ARRAY_SIZE(plane_formats_yuv), \
 	.virt_format_list = plane_formats, \
 	.virt_num_formats = ARRAY_SIZE(plane_formats), \
+	.rotation_cfg = rot_cfg, \
 	}
 
 #define _DMA_SBLK(num, sdma_pri) \
@@ -498,13 +518,13 @@  static const struct dpu_ctl_cfg sc7280_ctl[] = {
 	}
 
 static const struct dpu_sspp_sub_blks sdm845_vig_sblk_0 =
-				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3);
+				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3, 0);
 static const struct dpu_sspp_sub_blks sdm845_vig_sblk_1 =
-				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3);
+				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3, 0);
 static const struct dpu_sspp_sub_blks sdm845_vig_sblk_2 =
-				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3);
+				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3, 0);
 static const struct dpu_sspp_sub_blks sdm845_vig_sblk_3 =
-				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3);
+				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3, 0);
 
 static const struct dpu_sspp_sub_blks sdm845_dma_sblk_0 = _DMA_SBLK("8", 1);
 static const struct dpu_sspp_sub_blks sdm845_dma_sblk_1 = _DMA_SBLK("9", 2);
@@ -543,7 +563,10 @@  static const struct dpu_sspp_cfg sdm845_sspp[] = {
 };
 
 static const struct dpu_sspp_sub_blks sc7180_vig_sblk_0 =
-				_VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4);
+				_VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4, 0);
+
+static const struct dpu_sspp_sub_blks sc7280_vig_sblk_0 =
+				_VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4, &dpu_rot_cfg);
 
 static const struct dpu_sspp_cfg sc7180_sspp[] = {
 	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7180_MASK,
@@ -557,13 +580,13 @@  static const struct dpu_sspp_cfg sc7180_sspp[] = {
 };
 
 static const struct dpu_sspp_sub_blks sm8250_vig_sblk_0 =
-				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3LITE);
+				_VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3LITE, 0);
 static const struct dpu_sspp_sub_blks sm8250_vig_sblk_1 =
-				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3LITE);
+				_VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3LITE, 0);
 static const struct dpu_sspp_sub_blks sm8250_vig_sblk_2 =
-				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3LITE);
+				_VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3LITE, 0);
 static const struct dpu_sspp_sub_blks sm8250_vig_sblk_3 =
-				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3LITE);
+				_VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3LITE, 0);
 
 static const struct dpu_sspp_cfg sm8250_sspp[] = {
 	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SM8250_MASK,
@@ -585,8 +608,8 @@  static const struct dpu_sspp_cfg sm8250_sspp[] = {
 };
 
 static const struct dpu_sspp_cfg sc7280_sspp[] = {
-	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7180_MASK,
-		sc7180_vig_sblk_0, 0,  SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
+	SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7280_MASK,
+		sc7280_vig_sblk_0, 0,  SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
 	SSPP_BLK("sspp_8", SSPP_DMA0, 0x24000,  DMA_SDM845_MASK,
 		sdm845_dma_sblk_0, 1, SSPP_TYPE_DMA, DPU_CLK_CTRL_DMA0),
 	SSPP_BLK("sspp_9", SSPP_DMA1, 0x26000,  DMA_CURSOR_SDM845_MASK,
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
index d2a945a..8421001 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
@@ -129,6 +129,7 @@  enum {
 	DPU_SSPP_TS_PREFILL,
 	DPU_SSPP_TS_PREFILL_REC1,
 	DPU_SSPP_CDP,
+	DPU_SSPP_INLINE_ROTATION,
 	DPU_SSPP_MAX
 };
 
@@ -309,6 +310,24 @@  struct dpu_qos_lut_tbl {
 };
 
 /**
+ * struct dpu_rotation_cfg - define inline rotation config
+ * @version: Inline rotation version
+ * @rot_maxdwnscale_ratio_num: max downscale ratio for rotation numerator
+ * @rot_maxdwnscale_ratio_dem: max downscale ratio for denominator
+ * @rot_maxheight: max pre rotated height allowed for rotation
+ * @rot_num_formats: count of the formats
+ * @rot_format_list: list of supported rotator formats
+ */
+struct dpu_rotation_cfg {
+	u32 version;
+	u32 rot_maxdwnscale_ratio_num;
+	u32 rot_maxdwnscale_ratio_dem;
+	u32 rot_maxheight;
+	u32 rot_num_formats;
+	const u32 *rot_format_list;
+};
+
+/**
  * struct dpu_caps - define DPU capabilities
  * @max_mixer_width    max layer mixer line width support.
  * @max_mixer_blendstages max layer mixer blend stages or
@@ -384,6 +403,7 @@  struct dpu_sspp_sub_blks {
 	u32 num_formats;
 	const u32 *virt_format_list;
 	u32 virt_num_formats;
+	const struct dpu_rotation_cfg *rotation_cfg;
 };
 
 /**
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
index ec4a6f0..0daee63 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
@@ -539,16 +539,28 @@  static void _dpu_plane_set_scanout(struct drm_plane *plane,
 
 static void _dpu_plane_setup_scaler3(struct dpu_plane *pdpu,
 		struct dpu_plane_state *pstate,
-		uint32_t src_w, uint32_t src_h, uint32_t dst_w, uint32_t dst_h,
 		struct dpu_hw_scaler3_cfg *scale_cfg,
 		const struct dpu_format *fmt,
 		uint32_t chroma_subsmpl_h, uint32_t chroma_subsmpl_v)
 {
 	uint32_t i;
+	bool inline_rotation = (pstate->rotation & DRM_MODE_ROTATE_90);
+	uint32_t src_w = drm_rect_width(&pdpu->pipe_cfg.src_rect);
+	uint32_t src_h = drm_rect_height(&pdpu->pipe_cfg.src_rect);
+	uint32_t dst_w = drm_rect_width(&pdpu->pipe_cfg.dst_rect);
+	uint32_t dst_h = drm_rect_height(&pdpu->pipe_cfg.dst_rect);
 
 	memset(scale_cfg, 0, sizeof(*scale_cfg));
 	memset(&pstate->pixel_ext, 0, sizeof(struct dpu_hw_pixel_ext));
 
+	/*
+	 * For inline rotation cases, scaler config is post-rotation,
+	 * so swap the dimensions here. However, pixel extension will
+	 * need pre-rotation settings.
+	 */
+	if (inline_rotation)
+		swap(src_w, src_h);
+
 	scale_cfg->phase_step_x[DPU_SSPP_COMP_0] =
 		mult_frac((1 << PHASE_STEP_SHIFT), src_w, dst_w);
 	scale_cfg->phase_step_y[DPU_SSPP_COMP_0] =
@@ -587,10 +599,10 @@  static void _dpu_plane_setup_scaler3(struct dpu_plane *pdpu,
 			scale_cfg->preload_y[i] = DPU_QSEED3_DEFAULT_PRELOAD_V;
 		}
 
-		pstate->pixel_ext.num_ext_pxls_top[i] =
-			scale_cfg->src_height[i];
-		pstate->pixel_ext.num_ext_pxls_left[i] =
-			scale_cfg->src_width[i];
+		pstate->pixel_ext.num_ext_pxls_top[i] = inline_rotation ?
+			scale_cfg->src_width[i] : scale_cfg->src_height[i];
+		pstate->pixel_ext.num_ext_pxls_left[i] = inline_rotation ?
+			scale_cfg->src_height[i] : scale_cfg->src_width[i];
 	}
 	if (!(DPU_FORMAT_IS_YUV(fmt)) && (src_h == dst_h)
 		&& (src_w == dst_w))
@@ -662,10 +674,6 @@  static void _dpu_plane_setup_scaler(struct dpu_plane *pdpu,
 	/* don't chroma subsample if decimating */
 	/* update scaler. calculate default config for QSEED3 */
 	_dpu_plane_setup_scaler3(pdpu, pstate,
-			drm_rect_width(&pdpu->pipe_cfg.src_rect),
-			drm_rect_height(&pdpu->pipe_cfg.src_rect),
-			drm_rect_width(&pdpu->pipe_cfg.dst_rect),
-			drm_rect_height(&pdpu->pipe_cfg.dst_rect),
 			&pstate->scaler3_cfg, fmt,
 			info->hsub, info->vsub);
 }
@@ -959,6 +967,7 @@  static int dpu_plane_atomic_check(struct drm_plane *plane,
 	const struct dpu_format *fmt;
 	struct drm_rect src, dst, fb_rect = { 0 };
 	uint32_t min_src_size, max_linewidth;
+	unsigned int rotation;
 
 	if (new_plane_state->crtc)
 		crtc_state = drm_atomic_get_new_crtc_state(state,
@@ -1028,6 +1037,48 @@  static int dpu_plane_atomic_check(struct drm_plane *plane,
 		return -E2BIG;
 	}
 
+	rotation = drm_rotation_simplify(new_plane_state->rotation,
+			    DRM_MODE_ROTATE_0 |
+			    DRM_MODE_ROTATE_90 |
+			    DRM_MODE_REFLECT_X |
+			    DRM_MODE_REFLECT_Y);
+
+	if (rotation & DRM_MODE_ROTATE_90) {
+		struct msm_drm_private *priv = plane->dev->dev_private;
+		struct dpu_kms *dpu_kms;
+		const struct msm_format *msm_fmt;
+		const struct dpu_format *fmt;
+		bool found = false;
+		u32 i, num_formats;
+		const u32 *supported_formats;
+
+		if (src.y2 > pdpu->pipe_sblk->rotation_cfg->rot_maxheight) {
+			DPU_DEBUG_PLANE(pdpu,
+			"invalid height for inline rot:%d max:%d\n",
+			src.y2, pdpu->pipe_sblk->rotation_cfg->rot_maxheight);
+			return -EINVAL;
+		}
+
+		/* check for valid formats supported by inline rotation */
+		dpu_kms = to_dpu_kms(priv->kms);
+		msm_fmt = msm_framebuffer_format(new_plane_state->fb);
+		fmt = to_dpu_format(msm_fmt);
+		supported_formats = pdpu->pipe_sblk->rotation_cfg->rot_format_list;
+		num_formats = pdpu->pipe_sblk->rotation_cfg->rot_num_formats;
+
+		for (i = 0; i < num_formats; i++) {
+			if (fmt->base.pixel_format == supported_formats[i] &&
+				fmt->fetch_mode == DPU_FETCH_UBWC)
+				found = true;
+		}
+
+		if (!found || !num_formats) {
+			DPU_DEBUG_PLANE(pdpu,
+			"supported_format not found num:%d\n", num_formats);
+			return -EINVAL;
+		}
+	}
+	pstate->rotation = rotation;
 	pstate->needs_qos_remap = drm_atomic_crtc_needs_modeset(crtc_state);
 
 	return 0;
@@ -1153,21 +1204,18 @@  static void dpu_plane_sspp_atomic_update(struct drm_plane *plane)
 				pstate->multirect_mode);
 
 	if (pdpu->pipe_hw->ops.setup_format) {
-		unsigned int rotation;
 
 		src_flags = 0x0;
 
-		rotation = drm_rotation_simplify(state->rotation,
-						 DRM_MODE_ROTATE_0 |
-						 DRM_MODE_REFLECT_X |
-						 DRM_MODE_REFLECT_Y);
-
-		if (rotation & DRM_MODE_REFLECT_X)
+		if (pstate->rotation & DRM_MODE_REFLECT_X)
 			src_flags |= DPU_SSPP_FLIP_LR;
 
-		if (rotation & DRM_MODE_REFLECT_Y)
+		if (pstate->rotation & DRM_MODE_REFLECT_Y)
 			src_flags |= DPU_SSPP_FLIP_UD;
 
+		if (pstate->rotation & DRM_MODE_ROTATE_90)
+			src_flags |= DPU_SSPP_ROT_90;
+
 		/* update format */
 		pdpu->pipe_hw->ops.setup_format(pdpu->pipe_hw, fmt, src_flags,
 				pstate->multirect_index);
@@ -1578,6 +1626,8 @@  struct drm_plane *dpu_plane_init(struct drm_device *dev,
 	int zpos_max = DPU_ZPOS_MAX;
 	uint32_t num_formats;
 	int ret = -EINVAL;
+	unsigned int supported_rotations = DRM_MODE_ROTATE_0 |
+			DRM_MODE_ROTATE_180 | DRM_MODE_REFLECT_X | DRM_MODE_REFLECT_Y;
 
 	/* create and zero local structure */
 	pdpu = kzalloc(sizeof(*pdpu), GFP_KERNEL);
@@ -1647,12 +1697,11 @@  struct drm_plane *dpu_plane_init(struct drm_device *dev,
 	if (ret)
 		DPU_ERROR("failed to install zpos property, rc = %d\n", ret);
 
+	if (pdpu->features & BIT(DPU_SSPP_INLINE_ROTATION))
+		supported_rotations |= DRM_MODE_ROTATE_90;
+
 	drm_plane_create_rotation_property(plane,
-			DRM_MODE_ROTATE_0,
-			DRM_MODE_ROTATE_0 |
-			DRM_MODE_ROTATE_180 |
-			DRM_MODE_REFLECT_X |
-			DRM_MODE_REFLECT_Y);
+		    DRM_MODE_ROTATE_0, supported_rotations);
 
 	drm_plane_enable_fb_damage_clips(plane);
 
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
index 34e03ac..16ec8dc 100644
--- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
+++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
@@ -28,6 +28,7 @@ 
  * @cdp_cfg:	CDP configuration
  * @plane_fetch_bw: calculated BW per plane
  * @plane_clk: calculated clk per plane
+ * @rotation: simplified drm rotation hint
  */
 struct dpu_plane_state {
 	struct drm_plane_state base;
@@ -45,6 +46,7 @@  struct dpu_plane_state {
 	struct dpu_hw_pipe_cdp_cfg cdp_cfg;
 	u64 plane_fetch_bw;
 	u64 plane_clk;
+	unsigned int rotation;
 };
 
 /**