[1/3] drm/panel: Add DT bindings for Ilitek ILI9322

Commit Message

Linus Walleij Dec. 1, 2017, 4:16 p.m. UTC

This adds device tree bindings for the Ilitek ILI9322
320x240 TFT panel driver.

Cc: David Lechner <[e-mail]>
Cc: Stefano Babic <[e-mail]>
Cc: Ben Dooks <[e-mail]>
Cc: [e-mail]
Signed-off-by: Linus Walleij <[e-mail]>
---
ChangeLog v1->v2:
- Add explicit requirement to specify the system type so the
  driver can look up the display configuration from the
  compatible string.
- Dropped all display-specific configuration data I could
  in favor of open coding it all in a per-system config struct
  in the driver.
- Now only regulators and GPIO lines remain as DT resources.
---
 .../bindings/display/panel/ilitek,ili9322.txt      | 49 ++++++++++++++++++++++
 1 file changed, 49 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt

Comments

Rob Herring Dec. 1, 2017, 7:49 p.m. UTC | #1

On Fri, Dec 1, 2017 at 10:16 AM, Linus Walleij <[e-mail]> wrote:
> This adds device tree bindings for the Ilitek ILI9322
> 320x240 TFT panel driver.
>
> Cc: David Lechner <[e-mail]>
> Cc: Stefano Babic <[e-mail]>
> Cc: Ben Dooks <[e-mail]>
> Cc: [e-mail]
> Signed-off-by: Linus Walleij <[e-mail]>
> ---
> ChangeLog v1->v2:
> - Add explicit requirement to specify the system type so the
>   driver can look up the display configuration from the
>   compatible string.
> - Dropped all display-specific configuration data I could
>   in favor of open coding it all in a per-system config struct
>   in the driver.
> - Now only regulators and GPIO lines remain as DT resources.
> ---
>  .../bindings/display/panel/ilitek,ili9322.txt      | 49 ++++++++++++++++++++++
>  1 file changed, 49 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt

Reviewed-by: Rob Herring <[e-mail]>

Patch

diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
new file mode 100644
index 000000000000..3d5ce6ad6ec7
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
@@ -0,0 +1,49 @@ 
+Ilitek ILI9322 TFT panel driver with SPI control bus
+
+This is a driver for 320x240 TFT panels, accepting a variety of input
+streams that get adapted and scaled to the panel. The panel output has
+960 TFT source driver pins and 240 TFT gate driver pins, VCOM, VCOML and
+VCOMH outputs.
+
+Required properties:
+  - compatible: "dlink,dir-685-panel", "ilitek,ili9322"
+    (full system-specific compatible is always required to look up configuration)
+  - reg: address of the panel on the SPI bus
+
+Optional properties:
+  - vcc-supply: core voltage supply, see regulator/regulator.txt
+  - iovcc-supply: voltage supply for the interface input/output signals,
+    see regulator/regulator.txt
+  - vci-supply: voltage supply for analog parts, see regulator/regulator.txt
+  - reset-gpios: a GPIO spec for the reset pin, see gpio/gpio.txt
+
+  The following optional properties only apply to RGB and YUV input modes and
+  can be omitted for BT.656 input modes:
+
+  - pixelclk-active: see display/panel/display-timing.txt
+  - de-active: see display/panel/display-timing.txt
+  - hsync-active: see display/panel/display-timing.txt
+  - vsync-active: see display/panel/display-timing.txt
+
+The panel must obey the rules for a SPI slave device as specified in
+spi/spi-bus.txt
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in
+media/video-interfaces.txt. This node should describe panel's video bus.
+
+Example:
+
+panel: display@0 {
+	compatible = "dlink,dir-685-panel", "ilitek,ili9322";
+	reg = <0>;
+	vcc-supply = <&vdisp>;
+	iovcc-supply = <&vdisp>;
+	vci-supply = <&vdisp>;
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&display_out>;
+		};
+	};
+};