@@ -4937,6 +4937,12 @@ S: Orphan / Obsolete
F: drivers/gpu/drm/sis/
F: include/uapi/drm/sis_drm.h
+DRM DRIVER FOR SITRONIX ST7701 PANELS
+M: Jagan Teki <jagan@amarulasolutions.com>
+S: Maintained
+F: drivers/gpu/drm/panel/panel-sitronix-st7701.c
+F: Documentation/devicetree/bindings/display/panel/sitronix,st7701.txt
+
DRM DRIVER FOR SITRONIX ST7586 PANELS
M: David Lechner <david@lechnology.com>
S: Maintained
@@ -214,6 +214,16 @@ config DRM_PANEL_SHARP_LS043T1LE01
Say Y here if you want to enable support for Sharp LS043T1LE01 qHD
(540x960) DSI panel as found on the Qualcomm APQ8074 Dragonboard
+config DRM_PANEL_SITRONIX_ST7701
+ tristate "Sitronix ST7701 panel driver"
+ depends on OF
+ depends on DRM_MIPI_DSI
+ depends on BACKLIGHT_CLASS_DEVICE
+ help
+ Say Y here if you want to enable support for the Sitronix
+ ST7701 controller for 480X864 LCD panels with MIPI/RGB/SPI
+ system interfaces.
+
config DRM_PANEL_SITRONIX_ST7789V
tristate "Sitronix ST7789V panel"
depends on OF && SPI
@@ -22,6 +22,7 @@ obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0) += panel-samsung-s6e8aa0.o
obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += panel-seiko-43wvf1g.o
obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
+obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7701) += panel-sitronix-st7701.o
obj-$(CONFIG_DRM_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
obj-$(CONFIG_DRM_PANEL_TPO_TPG110) += panel-tpo-tpg110.o
obj-$(CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA) += panel-truly-nt35597.o
new file mode 100644
@@ -0,0 +1,429 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019, Amarula Solutions.
+ * Author: Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+#include <linux/backlight.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+
+#include <linux/gpio/consumer.h>
+#include <linux/regulator/consumer.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+
+#include <video/mipi_display.h>
+
+/* Command2 BKx selection command */
+#define DSI_CMD2BKX_SEL 0xFF
+
+/* Command2, BK0 commands */
+#define DSI_CMD2_BK0_PVGAMCTRL 0xB0 /* Positive Voltage Gamma Control */
+#define DSI_CMD2_BK0_NVGAMCTRL 0xB1 /* Negative Voltage Gamma Control */
+#define DSI_CMD2_BK0_LNESET 0xC0 /* Display Line setting */
+#define DSI_CMD2_BK0_PORCTRL 0xC1 /* Porch control */
+#define DSI_CMD2_BK0_INVSEL 0xC2 /* Inversion selection, Frame Rate Control */
+
+/* Command2, BK1 commands */
+#define DSI_CMD2_BK1_VRHS 0xB0 /* Vop amplitude setting */
+#define DSI_CMD2_BK1_VCOM 0xB1 /* VCOM amplitude setting */
+#define DSI_CMD2_BK1_VGHSS 0xB2 /* VGH Voltage setting */
+#define DSI_CMD2_BK1_TESTCMD 0xB3 /* TEST Command Setting */
+#define DSI_CMD2_BK1_VGLS 0xB5 /* VGL Voltage setting */
+#define DSI_CMD2_BK1_PWCTLR1 0xB7 /* Power Control 1 */
+#define DSI_CMD2_BK1_PWCTLR2 0xB8 /* Power Control 2 */
+#define DSI_CMD2_BK1_SPD1 0xC1 /* Source pre_drive timing set1 */
+#define DSI_CMD2_BK1_SPD2 0xC2 /* Source EQ2 Setting */
+#define DSI_CMD2_BK1_MIPISET1 0xD0 /* MIPI Setting 1 */
+
+/**
+ * Command2 with BK function selection.
+ *
+ * BIT[4, 0]: [CN2, BKXSEL]
+ * 10 = CMD2BK0, Command2 BK0
+ * 11 = CMD2BK1, Command2 BK1
+ * 00 = Command2 disable
+ */
+#define DSI_CMD2BK1_SEL 0x11
+#define DSI_CMD2BK0_SEL 0x10
+#define DSI_CMD2BKX_SEL_NONE 0x00
+
+/* Command2, BK0 bytes */
+#define DSI_LINESET_LINE 0x69
+#define DSI_LINESET_LDE_EN BIT(7)
+#define DSI_LINESET_LINEDELTA GENMASK(1, 0)
+#define DSI_CMD2_BK0_LNESET_B1 DSI_LINESET_LINEDELTA
+#define DSI_CMD2_BK0_LNESET_B0 (DSI_LINESET_LDE_EN | DSI_LINESET_LINE)
+#define DSI_INVSEL_DEFAULT GENMASK(5, 4)
+#define DSI_INVSEL_NLINV GENMASK(2, 0)
+#define DSI_INVSEL_RTNI GENMASK(2, 1)
+#define DSI_CMD2_BK0_INVSEL_B1 DSI_INVSEL_RTNI
+#define DSI_CMD2_BK0_INVSEL_B0 (DSI_INVSEL_DEFAULT | DSI_INVSEL_NLINV)
+#define DSI_CMD2_BK0_PORCTRL_B0(m) ((m)->vtotal - (m)->vsync_end)
+#define DSI_CMD2_BK0_PORCTRL_B1(m) ((m)->vsync_start - (m)->vdisplay)
+
+/* Command2, BK1 bytes */
+#define DSI_CMD2_BK1_VRHA_SET 0x45
+#define DSI_CMD2_BK1_VCOM_SET 0x13
+#define DSI_CMD2_BK1_VGHSS_SET GENMASK(2, 0)
+#define DSI_CMD2_BK1_TESTCMD_VAL BIT(7)
+#define DSI_VGLS_DEFAULT BIT(6)
+#define DSI_VGLS_SEL GENMASK(2, 0)
+#define DSI_CMD2_BK1_VGLS_SET (DSI_VGLS_DEFAULT | DSI_VGLS_SEL)
+#define DSI_PWCTLR1_AP BIT(7) /* Gamma OP bias, max */
+#define DSI_PWCTLR1_APIS BIT(2) /* Source OP input bias, min */
+#define DSI_PWCTLR1_APOS BIT(0) /* Source OP output bias, min */
+#define DSI_CMD2_BK1_PWCTLR1_SET (DSI_PWCTLR1_AP | DSI_PWCTLR1_APIS | \
+ DSI_PWCTLR1_APOS)
+#define DSI_PWCTLR2_AVDD BIT(5) /* AVDD 6.6v */
+#define DSI_PWCTLR2_AVCL 0x0 /* AVCL -4.4v */
+#define DSI_CMD2_BK1_PWCTLR2_SET (DSI_PWCTLR2_AVDD | DSI_PWCTLR2_AVCL)
+#define DSI_SPD1_T2D BIT(3)
+#define DSI_CMD2_BK1_SPD1_SET (GENMASK(6, 4) | DSI_SPD1_T2D)
+#define DSI_CMD2_BK1_SPD2_SET DSI_CMD2_BK1_SPD1_SET
+#define DSI_MIPISET1_EOT_EN BIT(3)
+#define DSI_CMD2_BK1_MIPISET1_SET (BIT(7) | DSI_MIPISET1_EOT_EN)
+
+struct st7701_panel_desc {
+ const struct drm_display_mode *mode;
+ unsigned int lanes;
+ unsigned long flags;
+ enum mipi_dsi_pixel_format format;
+ const char *const *supply_names;
+ unsigned int num_supplies;
+ unsigned int panel_sleep_delay;
+};
+
+struct st7701 {
+ struct drm_panel panel;
+ struct mipi_dsi_device *dsi;
+ const struct st7701_panel_desc *desc;
+
+ struct backlight_device *backlight;
+ struct regulator_bulk_data *supplies;
+ struct gpio_desc *reset;
+ unsigned int sleep_delay;
+};
+
+static inline struct st7701 *panel_to_st7701(struct drm_panel *panel)
+{
+ return container_of(panel, struct st7701, panel);
+}
+
+static inline int st7701_dsi_write(struct st7701 *st7701, const void *seq,
+ size_t len)
+{
+ return mipi_dsi_dcs_write_buffer(st7701->dsi, seq, len);
+}
+
+#define ST7701_DSI(st7701, seq...) \
+ { \
+ const u8 d[] = { seq }; \
+ st7701_dsi_write(st7701, d, ARRAY_SIZE(d)); \
+ }
+
+static void st7701_init_sequence(struct st7701 *st7701)
+{
+ const struct drm_display_mode *mode = st7701->desc->mode;
+
+ ST7701_DSI(st7701, MIPI_DCS_SOFT_RESET, 0x00);
+
+ /* We need to wait 5ms before sending new commands */
+ msleep(5);
+
+ ST7701_DSI(st7701, MIPI_DCS_EXIT_SLEEP_MODE, 0x00);
+
+ msleep(st7701->sleep_delay);
+
+ /* Command2, BK0 */
+ ST7701_DSI(st7701, DSI_CMD2BKX_SEL,
+ 0x77, 0x01, 0x00, 0x00, DSI_CMD2BK0_SEL);
+ ST7701_DSI(st7701, DSI_CMD2_BK0_PVGAMCTRL, 0x00, 0x0E, 0x15, 0x0F,
+ 0x11, 0x08, 0x08, 0x08, 0x08, 0x23, 0x04, 0x13, 0x12,
+ 0x2B, 0x34, 0x1F);
+ ST7701_DSI(st7701, DSI_CMD2_BK0_NVGAMCTRL, 0x00, 0x0E, 0x95, 0x0F,
+ 0x13, 0x07, 0x09, 0x08, 0x08, 0x22, 0x04, 0x10, 0x0E,
+ 0x2C, 0x34, 0x1F);
+ ST7701_DSI(st7701, DSI_CMD2_BK0_LNESET,
+ DSI_CMD2_BK0_LNESET_B0, DSI_CMD2_BK0_LNESET_B1);
+ ST7701_DSI(st7701, DSI_CMD2_BK0_PORCTRL,
+ DSI_CMD2_BK0_PORCTRL_B0(mode),
+ DSI_CMD2_BK0_PORCTRL_B1(mode));
+ ST7701_DSI(st7701, DSI_CMD2_BK0_INVSEL,
+ DSI_CMD2_BK0_INVSEL_B0, DSI_CMD2_BK0_INVSEL_B1);
+
+ /* Command2, BK1 */
+ ST7701_DSI(st7701, DSI_CMD2BKX_SEL,
+ 0x77, 0x01, 0x00, 0x00, DSI_CMD2BK1_SEL);
+ ST7701_DSI(st7701, DSI_CMD2_BK1_VRHS, DSI_CMD2_BK1_VRHA_SET);
+ ST7701_DSI(st7701, DSI_CMD2_BK1_VCOM, DSI_CMD2_BK1_VCOM_SET);
+ ST7701_DSI(st7701, DSI_CMD2_BK1_VGHSS, DSI_CMD2_BK1_VGHSS_SET);
+ ST7701_DSI(st7701, DSI_CMD2_BK1_TESTCMD, DSI_CMD2_BK1_TESTCMD_VAL);
+ ST7701_DSI(st7701, DSI_CMD2_BK1_VGLS, DSI_CMD2_BK1_VGLS_SET);
+ ST7701_DSI(st7701, DSI_CMD2_BK1_PWCTLR1, DSI_CMD2_BK1_PWCTLR1_SET);
+ ST7701_DSI(st7701, DSI_CMD2_BK1_PWCTLR2, DSI_CMD2_BK1_PWCTLR2_SET);
+ ST7701_DSI(st7701, DSI_CMD2_BK1_SPD1, DSI_CMD2_BK1_SPD1_SET);
+ ST7701_DSI(st7701, DSI_CMD2_BK1_SPD2, DSI_CMD2_BK1_SPD2_SET);
+ ST7701_DSI(st7701, DSI_CMD2_BK1_MIPISET1, DSI_CMD2_BK1_MIPISET1_SET);
+
+ /**
+ * ST7701_SPEC_V1.2 is unable to provide enough information above this
+ * specific command sequence, so grab the same from vendor BSP driver.
+ */
+ ST7701_DSI(st7701, 0xE0, 0x00, 0x00, 0x02);
+ ST7701_DSI(st7701, 0xE1, 0x0B, 0x00, 0x0D, 0x00, 0x0C, 0x00, 0x0E,
+ 0x00, 0x00, 0x44, 0x44);
+ ST7701_DSI(st7701, 0xE2, 0x33, 0x33, 0x44, 0x44, 0x64, 0x00, 0x66,
+ 0x00, 0x65, 0x00, 0x67, 0x00, 0x00);
+ ST7701_DSI(st7701, 0xE3, 0x00, 0x00, 0x33, 0x33);
+ ST7701_DSI(st7701, 0xE4, 0x44, 0x44);
+ ST7701_DSI(st7701, 0xE5, 0x0C, 0x78, 0x3C, 0xA0, 0x0E, 0x78, 0x3C,
+ 0xA0, 0x10, 0x78, 0x3C, 0xA0, 0x12, 0x78, 0x3C, 0xA0);
+ ST7701_DSI(st7701, 0xE6, 0x00, 0x00, 0x33, 0x33);
+ ST7701_DSI(st7701, 0xE7, 0x44, 0x44);
+ ST7701_DSI(st7701, 0xE8, 0x0D, 0x78, 0x3C, 0xA0, 0x0F, 0x78, 0x3C,
+ 0xA0, 0x11, 0x78, 0x3C, 0xA0, 0x13, 0x78, 0x3C, 0xA0);
+ ST7701_DSI(st7701, 0xEB, 0x02, 0x02, 0x39, 0x39, 0xEE, 0x44, 0x00);
+ ST7701_DSI(st7701, 0xEC, 0x00, 0x00);
+ ST7701_DSI(st7701, 0xED, 0xFF, 0xF1, 0x04, 0x56, 0x72, 0x3F, 0xFF,
+ 0xFF, 0xFF, 0xFF, 0xF3, 0x27, 0x65, 0x40, 0x1F, 0xFF);
+
+ /* disable Command2 */
+ ST7701_DSI(st7701, DSI_CMD2BKX_SEL,
+ 0x77, 0x01, 0x00, 0x00, DSI_CMD2BKX_SEL_NONE);
+}
+
+static int st7701_prepare(struct drm_panel *panel)
+{
+ struct st7701 *st7701 = panel_to_st7701(panel);
+ int ret;
+
+ gpiod_set_value(st7701->reset, 0);
+
+ ret = regulator_bulk_enable(st7701->desc->num_supplies,
+ st7701->supplies);
+ if (ret < 0)
+ return ret;
+ msleep(20);
+
+ gpiod_set_value(st7701->reset, 1);
+ msleep(150);
+
+ st7701_init_sequence(st7701);
+
+ return 0;
+}
+
+static int st7701_enable(struct drm_panel *panel)
+{
+ struct st7701 *st7701 = panel_to_st7701(panel);
+
+ ST7701_DSI(st7701, MIPI_DCS_SET_DISPLAY_ON, 0x00);
+ backlight_enable(st7701->backlight);
+
+ return 0;
+}
+
+static int st7701_disable(struct drm_panel *panel)
+{
+ struct st7701 *st7701 = panel_to_st7701(panel);
+
+ backlight_disable(st7701->backlight);
+ ST7701_DSI(st7701, MIPI_DCS_SET_DISPLAY_OFF, 0x00);
+
+ return 0;
+}
+
+static int st7701_unprepare(struct drm_panel *panel)
+{
+ struct st7701 *st7701 = panel_to_st7701(panel);
+
+ ST7701_DSI(st7701, MIPI_DCS_ENTER_SLEEP_MODE, 0x00);
+
+ msleep(st7701->sleep_delay);
+
+ gpiod_set_value(st7701->reset, 0);
+
+ /**
+ * During the Resetting period, the display will be blanked
+ * (The display is entering blanking sequence, which maximum
+ * time is 120 ms, when Reset Starts in Sleep Out –mode. The
+ * display remains the blank state in Sleep In –mode.) and
+ * then return to Default condition for Hardware Reset.
+ *
+ * So we need wait sleep_delay time to make sure reset completed.
+ */
+ msleep(st7701->sleep_delay);
+
+ regulator_bulk_disable(st7701->desc->num_supplies, st7701->supplies);
+
+ return 0;
+}
+
+static int st7701_get_modes(struct drm_panel *panel)
+{
+ struct st7701 *st7701 = panel_to_st7701(panel);
+ const struct drm_display_mode *desc_mode = st7701->desc->mode;
+ struct drm_display_mode *mode;
+
+ mode = drm_mode_duplicate(panel->drm, desc_mode);
+ if (!mode) {
+ DRM_DEV_ERROR(&st7701->dsi->dev,
+ "failed to add mode %ux%ux@%u\n",
+ desc_mode->hdisplay, desc_mode->vdisplay,
+ desc_mode->vrefresh);
+ return -ENOMEM;
+ }
+
+ drm_mode_set_name(mode);
+ drm_mode_probed_add(panel->connector, mode);
+
+ panel->connector->display_info.width_mm = desc_mode->width_mm;
+ panel->connector->display_info.height_mm = desc_mode->height_mm;
+
+ return 1;
+}
+
+static const struct drm_panel_funcs st7701_funcs = {
+ .disable = st7701_disable,
+ .unprepare = st7701_unprepare,
+ .prepare = st7701_prepare,
+ .enable = st7701_enable,
+ .get_modes = st7701_get_modes,
+};
+
+static const struct drm_display_mode ts8550b_mode = {
+ .clock = 27500,
+
+ .hdisplay = 480,
+ .hsync_start = 480 + 38,
+ .hsync_end = 480 + 38 + 12,
+ .htotal = 480 + 38 + 12 + 12,
+
+ .vdisplay = 854,
+ .vsync_start = 854 + 4,
+ .vsync_end = 854 + 4 + 8,
+ .vtotal = 854 + 4 + 8 + 18,
+
+ .width_mm = 69,
+ .height_mm = 139,
+
+ .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
+};
+
+static const char * const ts8550b_supply_names[] = {
+ "VCC",
+ "IOVCC",
+};
+
+static const struct st7701_panel_desc ts8550b_desc = {
+ .mode = &ts8550b_mode,
+ .lanes = 2,
+ .flags = MIPI_DSI_MODE_VIDEO,
+ .format = MIPI_DSI_FMT_RGB888,
+ .supply_names = ts8550b_supply_names,
+ .num_supplies = ARRAY_SIZE(ts8550b_supply_names),
+ .panel_sleep_delay = 80, /* panel need extra 80ms for sleep out cmd */
+};
+
+static int st7701_dsi_probe(struct mipi_dsi_device *dsi)
+{
+ const struct st7701_panel_desc *desc;
+ struct st7701 *st7701;
+ int ret, i;
+
+ st7701 = devm_kzalloc(&dsi->dev, sizeof(*st7701), GFP_KERNEL);
+ if (!st7701)
+ return -ENOMEM;
+
+ desc = of_device_get_match_data(&dsi->dev);
+ dsi->mode_flags = desc->flags;
+ dsi->format = desc->format;
+ dsi->lanes = desc->lanes;
+
+ st7701->supplies = devm_kcalloc(&dsi->dev, desc->num_supplies,
+ sizeof(*st7701->supplies),
+ GFP_KERNEL);
+ if (!st7701->supplies)
+ return -ENOMEM;
+
+ for (i = 0; i < desc->num_supplies; i++)
+ st7701->supplies[i].supply = desc->supply_names[i];
+
+ ret = devm_regulator_bulk_get(&dsi->dev, desc->num_supplies,
+ st7701->supplies);
+ if (ret < 0)
+ return ret;
+
+ st7701->reset = devm_gpiod_get(&dsi->dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(st7701->reset)) {
+ DRM_DEV_ERROR(&dsi->dev, "Couldn't get our reset GPIO\n");
+ return PTR_ERR(st7701->reset);
+ }
+
+ st7701->backlight = devm_of_find_backlight(&dsi->dev);
+ if (IS_ERR(st7701->backlight))
+ return PTR_ERR(st7701->backlight);
+
+ drm_panel_init(&st7701->panel);
+
+ /**
+ * Once sleep out has been issued, ST7701 IC required to wait 120ms
+ * before initiating new commands.
+ *
+ * On top of that some panels might need an extra delay to wait, so
+ * add panel specific delay for those cases. As now this panel specific
+ * delay information is referenced from those panel BSP driver, example
+ * ts8550b and there is no valid documentation for that.
+ */
+ st7701->sleep_delay = 120 + desc->panel_sleep_delay;
+ st7701->panel.funcs = &st7701_funcs;
+ st7701->panel.dev = &dsi->dev;
+
+ ret = drm_panel_add(&st7701->panel);
+ if (ret < 0)
+ return ret;
+
+ mipi_dsi_set_drvdata(dsi, st7701);
+ st7701->dsi = dsi;
+ st7701->desc = desc;
+
+ return mipi_dsi_attach(dsi);
+}
+
+static int st7701_dsi_remove(struct mipi_dsi_device *dsi)
+{
+ struct st7701 *st7701 = mipi_dsi_get_drvdata(dsi);
+
+ mipi_dsi_detach(dsi);
+ drm_panel_remove(&st7701->panel);
+
+ if (st7701->backlight)
+ put_device(&st7701->backlight->dev);
+
+ return 0;
+}
+
+static const struct of_device_id st7701_of_match[] = {
+ { .compatible = "techstar,ts8550b", .data = &ts8550b_desc },
+ { }
+};
+MODULE_DEVICE_TABLE(of, st7701_of_match);
+
+static struct mipi_dsi_driver st7701_dsi_driver = {
+ .probe = st7701_dsi_probe,
+ .remove = st7701_dsi_remove,
+ .driver = {
+ .name = "st7701",
+ .of_match_table = st7701_of_match,
+ },
+};
+module_mipi_dsi_driver(st7701_dsi_driver);
+
+MODULE_AUTHOR("Jagan Teki <jagan@amarulasolutions.com>");
+MODULE_DESCRIPTION("Sitronix ST7701 LCD Panel Driver");
+MODULE_LICENSE("GPL");
ST7701 designed for small and medium sizes of TFT LCD display, is capable of supporting up to 480RGBX864 in resolution. It provides several system interfaces like MIPI/RGB/SPI. Currently added support for Techstar TS8550B which is ST7701 based 480x854, 2-lane MIPI DSI LCD panel. Driver now registering mipi_dsi device, but indeed it can extendable for RGB if any requirement trigger in future. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- Changes for v8: - use DRM_DEV_ERROR instead of dev_err - use devm_of_find_backlight() instead of of_parse_phandle() - remove unneeded 'num_supplies' from struct st7701 - add proper comments about panel sepecific sleep mode delay as per st7701 datasheet - update msleep delay values in .prepare as per datasheet and as per discussion in v7, thanks to 'Sam Ravnborg' - update msleep delay values in .unprepare as per datasheet and as per discussion in v7, thanks to 'Sam Ravnborg' - add proper comments on msleep delay values as per st7701 datasheet - use MIPI_DCS_ENTER_SLEEP_MODE in .unprepare - drop unneeded gpio set in .prepare and .unprepare as per panel-simple - remove unneeded include files - rebase on master Changes for v7: - rebase on master Changes for v6: - use sleep delay value as per datasheet - add panel_sleep_delay variable for panel specific delay - use command sequnce display on and off instead panel functions - add proper comments on the delays - remove delays from command switch - move mode type on struct display mode - drop refresh rate value, let drm compute Changes for v5: - found the chip from vendor, so added new panel driver - here is v4: https://patchwork.kernel.org/patch/10680335/ MAINTAINERS | 6 + drivers/gpu/drm/panel/Kconfig | 10 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-sitronix-st7701.c | 429 ++++++++++++++++++ 4 files changed, 446 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7701.c