diff mbox series

[12/12] arm64: dts: allwinner: orange-pi-3: Enable WiFi

Message ID 20190405234514.6183-13-megous@megous.com (mailing list archive)
State New, archived
Headers show
Series Add support for Orange Pi 3 | expand

Commit Message

Ondřej Jirman April 5, 2019, 11:45 p.m. UTC
From: Ondrej Jirman <megous@megous.com>

Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is
called bcm43356 and can be used with the brcmfmac driver. The module
is powered by the two always on regulators (not AXP805).

WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
configured so that it sets up an 1.8V input bias on this port. This is
done by the pio driver by reading the vcc-pg-supply voltage.

You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
configuration that can be found in the Xulongs's repository for H6:

https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256

Mainline brcmfmac driver expects the firmware and nvram at the
following paths relative to the firmware directory:

  brcm/brcmfmac43456-sdio.bin
  brcm/brcmfmac43456-sdio.txt

Signed-off-by: Ondrej Jirman <megous@megous.com>
---
 .../dts/allwinner/sun50i-h6-orangepi-3.dts    | 48 +++++++++++++++++++
 1 file changed, 48 insertions(+)

Comments

Clément Péron April 7, 2019, 3:31 p.m. UTC | #1
Hi,

On Sat, 6 Apr 2019 at 01:45, megous via linux-sunxi
<linux-sunxi@googlegroups.com> wrote:
>
> From: Ondrej Jirman <megous@megous.com>
>
> Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is
> called bcm43356 and can be used with the brcmfmac driver. The module
> is powered by the two always on regulators (not AXP805).
>
> WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
> configured so that it sets up an 1.8V input bias on this port. This is
> done by the pio driver by reading the vcc-pg-supply voltage.
>
> You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
> configuration that can be found in the Xulongs's repository for H6:
>
> https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
>
> Mainline brcmfmac driver expects the firmware and nvram at the
> following paths relative to the firmware directory:
>
>   brcm/brcmfmac43456-sdio.bin
>   brcm/brcmfmac43456-sdio.txt
>
> Signed-off-by: Ondrej Jirman <megous@megous.com>
> ---
>  .../dts/allwinner/sun50i-h6-orangepi-3.dts    | 48 +++++++++++++++++++
>  1 file changed, 48 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> index 5270142527f5..6a201829bb62 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> @@ -66,6 +66,26 @@
>                 regulator-always-on;
>         };
>
> +       reg_vcc33_wifi: vcc33-wifi {
> +               /* Always on 3.3V regulator for WiFi and BT */
> +               compatible = "regulator-fixed";
> +               regulator-name = "vcc33-wifi";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +               regulator-always-on;
> +                vin-supply = <&reg_vcc5v>;
> +       };
> +
> +       reg_vcc_wifi_io: vcc-wifi-io {
> +               /* Always on 1.8V/300mA regulator for WiFi and BT IO */
> +               compatible = "regulator-fixed";
> +               regulator-name = "vcc-wifi-io";
> +               regulator-min-microvolt = <1800000>;
> +               regulator-max-microvolt = <1800000>;
> +               regulator-always-on;
> +                vin-supply = <&reg_vcc33_wifi>;
> +       };
> +
>         /*
>          * The board uses 2.5V RGMII signalling. Power sequence
>          * to enable the phy is to enable GMAC-2V5 and GMAC-3V3 (aldo2)
> @@ -86,6 +106,14 @@
>                   */
>                  vin-supply = <&reg_aldo2>; /* GMAC-3V3 */
>          };
> +
> +       wifi_pwrseq: wifi_pwrseq {
> +               compatible = "mmc-pwrseq-simple";
> +               clocks = <&rtc 1>;

Maybe I missed something, but the RTC in H6 is not yet available :
https://lkml.org/lkml/2018/10/31/822

Regards,
Clement

> +               clock-names = "ext_clock";
> +               reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
> +               post-power-on-delay-ms = <200>;
> +       };
>  };
>
>  &cpu0 {
> @@ -146,6 +174,25 @@
>         status = "okay";
>  };
>
> +&mmc1 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&mmc1_pins>;
> +       vmmc-supply = <&reg_vcc33_wifi>;
> +       vqmmc-supply = <&reg_vcc_wifi_io>;
> +       mmc-pwrseq = <&wifi_pwrseq>;
> +       bus-width = <4>;
> +       non-removable;
> +       status = "okay";
> +
> +       brcm: sdio-wifi@1 {
> +               reg = <1>;
> +               compatible = "brcm,bcm4329-fmac";
> +               interrupt-parent = <&r_pio>;
> +               interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
> +               interrupt-names = "host-wake";
> +       };
> +};
> +
>  &ohci0 {
>         status = "okay";
>  };
> @@ -157,6 +204,7 @@
>  &pio {
>         vcc-pc-supply = <&reg_bldo2>;
>         vcc-pd-supply = <&reg_cldo1>;
> +       vcc-pg-supply = <&reg_vcc_wifi_io>;
>  };
>
>  &r_i2c {
> --
> 2.21.0
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
Ondřej Jirman April 7, 2019, 4:15 p.m. UTC | #2
On Sun, Apr 07, 2019 at 05:31:52PM +0200, Clément Péron wrote:
> Hi,
> 
> On Sat, 6 Apr 2019 at 01:45, megous via linux-sunxi
> <linux-sunxi@googlegroups.com> wrote:
> >
> > From: Ondrej Jirman <megous@megous.com>
> >
> > Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is
> > called bcm43356 and can be used with the brcmfmac driver. The module
> > is powered by the two always on regulators (not AXP805).
> >
> > WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
> > configured so that it sets up an 1.8V input bias on this port. This is
> > done by the pio driver by reading the vcc-pg-supply voltage.
> >
> > You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
> > configuration that can be found in the Xulongs's repository for H6:
> >
> > https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
> >
> > Mainline brcmfmac driver expects the firmware and nvram at the
> > following paths relative to the firmware directory:
> >
> >   brcm/brcmfmac43456-sdio.bin
> >   brcm/brcmfmac43456-sdio.txt
> >
> > Signed-off-by: Ondrej Jirman <megous@megous.com>
> > ---
> >  .../dts/allwinner/sun50i-h6-orangepi-3.dts    | 48 +++++++++++++++++++
> >  1 file changed, 48 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> > index 5270142527f5..6a201829bb62 100644
> > --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> > @@ -66,6 +66,26 @@
> >                 regulator-always-on;
> >         };
> >
> > +       reg_vcc33_wifi: vcc33-wifi {
> > +               /* Always on 3.3V regulator for WiFi and BT */
> > +               compatible = "regulator-fixed";
> > +               regulator-name = "vcc33-wifi";
> > +               regulator-min-microvolt = <3300000>;
> > +               regulator-max-microvolt = <3300000>;
> > +               regulator-always-on;
> > +                vin-supply = <&reg_vcc5v>;
> > +       };
> > +
> > +       reg_vcc_wifi_io: vcc-wifi-io {
> > +               /* Always on 1.8V/300mA regulator for WiFi and BT IO */
> > +               compatible = "regulator-fixed";
> > +               regulator-name = "vcc-wifi-io";
> > +               regulator-min-microvolt = <1800000>;
> > +               regulator-max-microvolt = <1800000>;
> > +               regulator-always-on;
> > +                vin-supply = <&reg_vcc33_wifi>;
> > +       };
> > +
> >         /*
> >          * The board uses 2.5V RGMII signalling. Power sequence
> >          * to enable the phy is to enable GMAC-2V5 and GMAC-3V3 (aldo2)
> > @@ -86,6 +106,14 @@
> >                   */
> >                  vin-supply = <&reg_aldo2>; /* GMAC-3V3 */
> >          };
> > +
> > +       wifi_pwrseq: wifi_pwrseq {
> > +               compatible = "mmc-pwrseq-simple";
> > +               clocks = <&rtc 1>;
> 
> Maybe I missed something, but the RTC in H6 is not yet available :
> https://lkml.org/lkml/2018/10/31/822

You're right. I'm using an out-of-tree patch for that and didn't notice the
dependency. I guess, WiFi DTS patch can be ignored for now.

thanks,
	o.

> Regards,
> Clement
> 
> > +               clock-names = "ext_clock";
> > +               reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
> > +               post-power-on-delay-ms = <200>;
> > +       };
> >  };
> >
> >  &cpu0 {
> > @@ -146,6 +174,25 @@
> >         status = "okay";
> >  };
> >
> > +&mmc1 {
> > +       pinctrl-names = "default";
> > +       pinctrl-0 = <&mmc1_pins>;
> > +       vmmc-supply = <&reg_vcc33_wifi>;
> > +       vqmmc-supply = <&reg_vcc_wifi_io>;
> > +       mmc-pwrseq = <&wifi_pwrseq>;
> > +       bus-width = <4>;
> > +       non-removable;
> > +       status = "okay";
> > +
> > +       brcm: sdio-wifi@1 {
> > +               reg = <1>;
> > +               compatible = "brcm,bcm4329-fmac";
> > +               interrupt-parent = <&r_pio>;
> > +               interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
> > +               interrupt-names = "host-wake";
> > +       };
> > +};
> > +
> >  &ohci0 {
> >         status = "okay";
> >  };
> > @@ -157,6 +204,7 @@
> >  &pio {
> >         vcc-pc-supply = <&reg_bldo2>;
> >         vcc-pd-supply = <&reg_cldo1>;
> > +       vcc-pg-supply = <&reg_vcc_wifi_io>;
> >  };
> >
> >  &r_i2c {
> > --
> > 2.21.0
> >
> > --
> > You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> > To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com.
> > For more options, visit https://groups.google.com/d/optout.
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
index 5270142527f5..6a201829bb62 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
@@ -66,6 +66,26 @@ 
 		regulator-always-on;
 	};
 
+	reg_vcc33_wifi: vcc33-wifi {
+		/* Always on 3.3V regulator for WiFi and BT */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc33-wifi";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+                vin-supply = <&reg_vcc5v>;
+	};
+
+	reg_vcc_wifi_io: vcc-wifi-io {
+		/* Always on 1.8V/300mA regulator for WiFi and BT IO */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-wifi-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+                vin-supply = <&reg_vcc33_wifi>;
+	};
+
 	/*
 	 * The board uses 2.5V RGMII signalling. Power sequence
 	 * to enable the phy is to enable GMAC-2V5 and GMAC-3V3 (aldo2)
@@ -86,6 +106,14 @@ 
                  */
                 vin-supply = <&reg_aldo2>; /* GMAC-3V3 */
         };
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
+		reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
+		post-power-on-delay-ms = <200>;
+	};
 };
 
 &cpu0 {
@@ -146,6 +174,25 @@ 
 	status = "okay";
 };
 
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_vcc33_wifi>;
+	vqmmc-supply = <&reg_vcc_wifi_io>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcm: sdio-wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
+		interrupt-names = "host-wake";
+	};
+};
+
 &ohci0 {
 	status = "okay";
 };
@@ -157,6 +204,7 @@ 
 &pio {
 	vcc-pc-supply = <&reg_bldo2>;
 	vcc-pd-supply = <&reg_cldo1>;
+	vcc-pg-supply = <&reg_vcc_wifi_io>;
 };
 
 &r_i2c {