diff mbox series

[v13,4/6] dt-bindings: display: mediatek: convert the document format from txt to yaml

Message ID 20200311071823.117899-5-jitao.shi@mediatek.com (mailing list archive)
State New, archived
Headers show
Series mt8183 dpi supports dual edge and pin mode swap | expand

Commit Message

Jitao Shi March 11, 2020, 7:18 a.m. UTC 
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
 .../display/mediatek/mediatek,dpi.txt         |  45 --------
 .../display/mediatek/mediatek,dpi.yaml        | 103 ++++++++++++++++++
 2 files changed, 103 insertions(+), 45 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
 create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml

Comments

Rob Herring (Arm) March 19, 2020, 6:33 p.m. UTC | #1 
On Wed, Mar 11, 2020 at 03:18:21PM +0800, Jitao Shi wrote:
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> ---
>  .../display/mediatek/mediatek,dpi.txt         |  45 --------
>  .../display/mediatek/mediatek,dpi.yaml        | 103 ++++++++++++++++++
>  2 files changed, 103 insertions(+), 45 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
>  create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
> 
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> deleted file mode 100644
> index 2dfb50a7321e..000000000000
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ /dev/null
> @@ -1,45 +0,0 @@
> -Mediatek DPI Device
> -===================
> -
> -The Mediatek DPI function block is a sink of the display subsystem and
> -provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
> -output bus.
> -
> -Required properties:
> -- compatible: "mediatek,<chip>-dpi"
> -  the supported chips are mt2701 , mt8173 and mt8183.
> -- reg: Physical base address and length of the controller's registers
> -- interrupts: The interrupt signal from the function block.
> -- clocks: device clocks
> -  See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
> -- clock-names: must contain "pixel", "engine", and "pll"
> -- port: Output port node with endpoint definitions as described in
> -  Documentation/devicetree/bindings/graph.txt. This port should be connected
> -  to the input port of an attached HDMI or LVDS encoder chip.
> -
> -Optional properties:
> -- pinctrl-names: Contain "default" and "sleep".
> -  pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
> -- pclk-sample: refer Documentation/devicetree/bindings/media/video-interfaces.txt.
> -
> -Example:
> -
> -dpi0: dpi@1401d000 {
> -	compatible = "mediatek,mt8173-dpi";
> -	reg = <0 0x1401d000 0 0x1000>;
> -	interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
> -	clocks = <&mmsys CLK_MM_DPI_PIXEL>,
> -		 <&mmsys CLK_MM_DPI_ENGINE>,
> -		 <&apmixedsys CLK_APMIXED_TVDPLL>;
> -	clock-names = "pixel", "engine", "pll";
> -	pinctrl-names = "default", "sleep";
> -	pinctrl-0 = <&dpi_pin_func>;
> -	pinctrl-1 = <&dpi_pin_idle>;
> -
> -	port {
> -		dpi0_out: endpoint {
> -			pclk-sample = <0>;
> -			remote-endpoint = <&hdmi0_in>;
> -		};
> -	};
> -};
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
> new file mode 100644
> index 000000000000..d65543e3bf8c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
> @@ -0,0 +1,103 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/mediatek/mediatek,dpi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: mediatek DPI Controller Device Tree Bindings
> +
> +maintainers:
> +  - CK Hu <ck.hu@mediatek.com>
> +  - Jitao shi <jitao.shi@mediatek.com>
> +
> +description: |
> +  The Mediatek DPI function block is a sink of the display subsystem and
> +  provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
> +  output bus.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - mediatek,mt2701-dpi
> +      - mediatek,mt8173-dpi
> +      - mediatek,mt8183-dpi
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    items:
> +      - description: Pixel Clock
> +      - description: Engine Clock
> +      - description: DPI PLL
> +
> +  clock-names:
> +    items:
> +      - const: pixel
> +      - const: engine
> +      - const: pll
> +
> +  pinctrl-0: true
> +  pinctrl-1: true
> +
> +  pinctrl-names:
> +    items:
> +      - const: default
> +      - const: sleep
> +
> +  port@0:
> +    type: object
> +    description:
> +      Output port node with endpoint definitions as described in
> +      Documentation/devicetree/bindings/graph.txt. This port should be connected
> +      to the input port of an attached HDMI or LVDS encoder chip.
> +
> +    properties:
> +      endpoint:
> +        type: object
> +
> +        properties:
> +          pclk-sample:
> +            items:
> +            - description: refer Documentation/devicetree/bindings/media/video-interfaces.txt.

This is not an array.

Just 'pclk-sample: true' if both values are allowed or 'const: 0|1' if 
only one value is allowed.

> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks
> +  - clock-names
> +  - port@0
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/clock/mt8173-clk.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    dpi0: dpi@1401d000 {
> +        compatible = "mediatek,mt8173-dpi";
> +        reg = <0 0x1401d000 0 0x1000>;
> +        interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
> +        clocks = <&mmsys CLK_MM_DPI_PIXEL>,
> +             <&mmsys CLK_MM_DPI_ENGINE>,
> +             <&apmixedsys CLK_APMIXED_TVDPLL>;
> +        clock-names = "pixel", "engine", "pll";
> +        pinctrl-names = "default", "sleep";
> +        pinctrl-0 = <&dpi_pin_func>;
> +        pinctrl-1 = <&dpi_pin_idle>;
> +
> +        port@0 {
> +            dpi0_out: endpoint {
> +                pclk-sample = <0>;
> +                remote-endpoint = <&hdmi0_in>;
> +            };
> +        };
> +    };
> +
> +...
> -- 
> 2.21.0
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
deleted file mode 100644
index 2dfb50a7321e..000000000000
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
+++ /dev/null
@@ -1,45 +0,0 @@ 
-Mediatek DPI Device
-===================
-
-The Mediatek DPI function block is a sink of the display subsystem and
-provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
-output bus.
-
-Required properties:
-- compatible: "mediatek,<chip>-dpi"
-  the supported chips are mt2701 , mt8173 and mt8183.
-- reg: Physical base address and length of the controller's registers
-- interrupts: The interrupt signal from the function block.
-- clocks: device clocks
-  See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
-- clock-names: must contain "pixel", "engine", and "pll"
-- port: Output port node with endpoint definitions as described in
-  Documentation/devicetree/bindings/graph.txt. This port should be connected
-  to the input port of an attached HDMI or LVDS encoder chip.
-
-Optional properties:
-- pinctrl-names: Contain "default" and "sleep".
-  pinctrl-names see Documentation/devicetree/bindings/pinctrlpinctrl-bindings.txt
-- pclk-sample: refer Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Example:
-
-dpi0: dpi@1401d000 {
-	compatible = "mediatek,mt8173-dpi";
-	reg = <0 0x1401d000 0 0x1000>;
-	interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&mmsys CLK_MM_DPI_PIXEL>,
-		 <&mmsys CLK_MM_DPI_ENGINE>,
-		 <&apmixedsys CLK_APMIXED_TVDPLL>;
-	clock-names = "pixel", "engine", "pll";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&dpi_pin_func>;
-	pinctrl-1 = <&dpi_pin_idle>;
-
-	port {
-		dpi0_out: endpoint {
-			pclk-sample = <0>;
-			remote-endpoint = <&hdmi0_in>;
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
new file mode 100644
index 000000000000..d65543e3bf8c
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
@@ -0,0 +1,103 @@ 
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/mediatek/mediatek,dpi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: mediatek DPI Controller Device Tree Bindings
+
+maintainers:
+  - CK Hu <ck.hu@mediatek.com>
+  - Jitao shi <jitao.shi@mediatek.com>
+
+description: |
+  The Mediatek DPI function block is a sink of the display subsystem and
+  provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel
+  output bus.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-dpi
+      - mediatek,mt8173-dpi
+      - mediatek,mt8183-dpi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Pixel Clock
+      - description: Engine Clock
+      - description: DPI PLL
+
+  clock-names:
+    items:
+      - const: pixel
+      - const: engine
+      - const: pll
+
+  pinctrl-0: true
+  pinctrl-1: true
+
+  pinctrl-names:
+    items:
+      - const: default
+      - const: sleep
+
+  port@0:
+    type: object
+    description:
+      Output port node with endpoint definitions as described in
+      Documentation/devicetree/bindings/graph.txt. This port should be connected
+      to the input port of an attached HDMI or LVDS encoder chip.
+
+    properties:
+      endpoint:
+        type: object
+
+        properties:
+          pclk-sample:
+            items:
+            - description: refer Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - port@0
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/mt8173-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    dpi0: dpi@1401d000 {
+        compatible = "mediatek,mt8173-dpi";
+        reg = <0 0x1401d000 0 0x1000>;
+        interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
+        clocks = <&mmsys CLK_MM_DPI_PIXEL>,
+             <&mmsys CLK_MM_DPI_ENGINE>,
+             <&apmixedsys CLK_APMIXED_TVDPLL>;
+        clock-names = "pixel", "engine", "pll";
+        pinctrl-names = "default", "sleep";
+        pinctrl-0 = <&dpi_pin_func>;
+        pinctrl-1 = <&dpi_pin_idle>;
+
+        port@0 {
+            dpi0_out: endpoint {
+                pclk-sample = <0>;
+                remote-endpoint = <&hdmi0_in>;
+            };
+        };
+    };
+
+...