@@ -19,6 +19,7 @@ struct lvds_codec {
struct device *dev;
struct drm_bridge bridge;
struct drm_bridge *panel_bridge;
+ struct drm_bridge_timings timings;
struct regulator *vcc;
struct gpio_desc *powerdown_gpio;
u32 connector_type;
@@ -78,8 +79,10 @@ static int lvds_codec_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct device_node *panel_node;
+ struct device_node *bus_node;
struct drm_panel *panel;
struct lvds_codec *lvds_codec;
+ u32 val;
lvds_codec = devm_kzalloc(dev, sizeof(*lvds_codec), GFP_KERNEL);
if (!lvds_codec)
@@ -119,6 +122,27 @@ static int lvds_codec_probe(struct platform_device *pdev)
if (IS_ERR(lvds_codec->panel_bridge))
return PTR_ERR(lvds_codec->panel_bridge);
+ /*
+ * Encoder might sample data on different clock edge than the display,
+ * for example OnSemi FIN3385 has a dedicated strapping pin to select
+ * the sampling edge.
+ */
+ if (lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS) {
+ bus_node = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0);
+ if (!bus_node) {
+ dev_dbg(dev, "bus DT node not found\n");
+ return -ENXIO;
+ }
+
+ if (!of_property_read_u32(dev->of_node, "pclk-sample", &val)) {
+ lvds_codec->timings.input_bus_flags = val ?
+ DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE :
+ DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
+ }
+
+ of_node_put(bus_node);
+ }
+
/*
* The panel_bridge bridge is attached to the panel's of_node,
* but we need a bridge attached to our of_node for our user
@@ -126,6 +150,7 @@ static int lvds_codec_probe(struct platform_device *pdev)
*/
lvds_codec->bridge.of_node = dev->of_node;
lvds_codec->bridge.funcs = &funcs;
+ lvds_codec->bridge.timings = &lvds_codec->timings;
drm_bridge_add(&lvds_codec->bridge);
platform_set_drvdata(pdev, lvds_codec);
The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to select input pixel data sampling edge. Add DT property "pclk-sample", not the same as the one used by display timings but rather the same as used by media, and configure bus flags based on this DT property. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Antonio Borneo <antonio.borneo@st.com> Cc: Benjamin Gaignard <benjamin.gaignard@st.com> Cc: Biju Das <biju.das.jz@bp.renesas.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Philippe Cornu <philippe.cornu@st.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: Yannick Fertre <yannick.fertre@st.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-stm32@st-md-mailman.stormreply.com To: dri-devel@lists.freedesktop.org --- V2: - Limit the pixelclk-active to encoders only - Update DT binding document V3: - Determine whether this is encoder from connector, i.e. lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS V4: - Switch to pclk-sample. Note that the value of this is inverted, so all the existing users of pixelclk-active using previous version of this patch must be reworked V5: - Move pclk-sample to endpoint. Again, all existing users of the bindings must be reworked --- drivers/gpu/drm/bridge/lvds-codec.c | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+)