@@ -237,7 +237,7 @@ static int wled3_set_brightness(struct wled *wled, u16 brightness)
for (i = 0; i < wled->cfg.num_strings; ++i) {
rc = regmap_bulk_write(wled->regmap, wled->ctrl_addr +
- WLED3_SINK_REG_BRIGHT(i),
+ WLED3_SINK_REG_BRIGHT(wled->cfg.enabled_strings[i]),
&v, sizeof(v));
if (rc < 0)
return rc;
@@ -259,7 +259,7 @@ static int wled4_set_brightness(struct wled *wled, u16 brightness)
for (i = 0; i < wled->cfg.num_strings; ++i) {
rc = regmap_bulk_write(wled->regmap, wled->sink_addr +
- WLED4_SINK_REG_BRIGHT(i),
+ WLED4_SINK_REG_BRIGHT(wled->cfg.enabled_strings[i]),
&v, sizeof(v));
if (rc < 0)
return rc;
@@ -569,7 +569,7 @@ static irqreturn_t wled_short_irq_handler(int irq, void *_wled)
static void wled_auto_string_detection(struct wled *wled)
{
- int rc = 0, i, delay_time_us;
+ int rc = 0, i, j, delay_time_us;
u32 sink_config = 0;
u8 sink_test = 0, sink_valid = 0, val;
bool fault_set;
@@ -616,14 +616,15 @@ static void wled_auto_string_detection(struct wled *wled)
/* Iterate through the strings one by one */
for (i = 0; i < wled->cfg.num_strings; i++) {
- sink_test = BIT((WLED4_SINK_REG_CURR_SINK_SHFT + i));
+ j = wled->cfg.enabled_strings[i];
+ sink_test = BIT((WLED4_SINK_REG_CURR_SINK_SHFT + j));
/* Enable feedback control */
rc = regmap_write(wled->regmap, wled->ctrl_addr +
- WLED3_CTRL_REG_FEEDBACK_CONTROL, i + 1);
+ WLED3_CTRL_REG_FEEDBACK_CONTROL, j + 1);
if (rc < 0) {
dev_err(wled->dev, "Failed to enable feedback for SINK %d rc = %d\n",
- i + 1, rc);
+ j + 1, rc);
goto failed_detect;
}
@@ -632,7 +633,7 @@ static void wled_auto_string_detection(struct wled *wled)
WLED4_SINK_REG_CURR_SINK, sink_test);
if (rc < 0) {
dev_err(wled->dev, "Failed to configure SINK %d rc=%d\n",
- i + 1, rc);
+ j + 1, rc);
goto failed_detect;
}
@@ -659,7 +660,7 @@ static void wled_auto_string_detection(struct wled *wled)
if (fault_set)
dev_dbg(wled->dev, "WLED OVP fault detected with SINK %d\n",
- i + 1);
+ j + 1);
else
sink_valid |= sink_test;
@@ -699,15 +700,16 @@ static void wled_auto_string_detection(struct wled *wled)
/* Enable valid sinks */
if (wled->version == 4) {
for (i = 0; i < wled->cfg.num_strings; i++) {
+ j = wled->cfg.enabled_strings[i];
if (sink_config &
- BIT(WLED4_SINK_REG_CURR_SINK_SHFT + i))
+ BIT(WLED4_SINK_REG_CURR_SINK_SHFT + j))
val = WLED4_SINK_REG_STR_MOD_MASK;
else
/* Disable modulator_en for unused sink */
val = 0;
rc = regmap_write(wled->regmap, wled->sink_addr +
- WLED4_SINK_REG_STR_MOD_EN(i), val);
+ WLED4_SINK_REG_STR_MOD_EN(j), val);
if (rc < 0) {
dev_err(wled->dev, "Failed to configure MODULATOR_EN rc=%d\n",
rc);
The hardware is capable of controlling any non-contiguous sequence of LEDs specified in the DT using qcom,enabled-strings as u32 array, and this also follows from the DT-bindings documentation. The numbers specified in this array represent indices of the LED strings that are to be enabled and disabled. Its value is appropriately used to setup and enable string modules, but completely disregarded in the set_brightness paths which only iterate over the number of strings linearly. Take an example where only string 2 is enabled with qcom,enabled_strings=<2>: this string is appropriately enabled but subsequent brightness changes would have only touched the zero'th brightness register because num_strings is 1 here. This is simply addressed by looking up the string for this index in the enabled_strings array just like the other codepaths that iterate over num_strings. Likewise enabled_strings is now also used in the autodetection path for consistent behaviour: when a list of strings is specified in DT only those strings will be probed for autodetection, analogous to how the number of strings that need to be probed is already bound by qcom,num-strings. After all autodetection uses the set_brightness helpers to set an initial value, which could otherwise end up changing brightness on a different set of strings. Fixes: 775d2ffb4af6 ("backlight: qcom-wled: Restructure the driver for WLED3") Fixes: 03b2b5e86986 ("backlight: qcom-wled: Add support for WLED4 peripheral") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> --- drivers/video/backlight/qcom-wled.c | 22 ++++++++++++---------- 1 file changed, 12 insertions(+), 10 deletions(-)