deleted file mode 100644
@@ -1,41 +0,0 @@
-NVIDIA Tegra MIPI pad calibration controller
-
-Required properties:
-- compatible: "nvidia,tegra<chip>-mipi"
-- reg: Physical base address and length of the controller's registers.
-- clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
-- clock-names: Must include the following entries:
- - mipi-cal
-- #nvidia,mipi-calibrate-cells: Should be 1. The cell is a bitmask of the pads
- that need to be calibrated for a given device.
-
-User nodes need to contain an nvidia,mipi-calibrate property that has a
-phandle to refer to the calibration controller node and a bitmask of the pads
-that need to be calibrated.
-
-Example:
-
- mipi: mipi@700e3000 {
- compatible = "nvidia,tegra114-mipi";
- reg = <0x700e3000 0x100>;
- clocks = <&tegra_car TEGRA114_CLK_MIPI_CAL>;
- clock-names = "mipi-cal";
- #nvidia,mipi-calibrate-cells = <1>;
- };
-
- ...
-
- host1x@50000000 {
- ...
-
- dsi@54300000 {
- ...
-
- nvidia,mipi-calibrate = <&mipi 0x060>;
-
- ...
- };
-
- ...
- };
new file mode 100644
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra114-mipi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra MIPI pad calibration controller
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^mipi@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - nvidia,tegra114-mipi
+ - nvidia,tegra210-mipi
+ - nvidia,tegra186-mipi
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: module clock
+
+ clock-names:
+ items:
+ - const: mipi-cal
+
+ power-domains:
+ maxItems: 1
+
+ "#nvidia,mipi-calibrate-cells":
+ description: The number of cells in a MIPI calibration specifier.
+ Should be 1. The single cell specifies a bitmask of the pads that
+ need to be calibrated for a given device.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ const: 1
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - "#nvidia,mipi-calibrate-cells"
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra114-car.h>
+
+ mipi@700e3000 {
+ compatible = "nvidia,tegra114-mipi";
+ reg = <0x700e3000 0x100>;
+ clocks = <&tegra_car TEGRA114_CLK_MIPI_CAL>;
+ clock-names = "mipi-cal";
+ #nvidia,mipi-calibrate-cells = <1>;
+ };
+
+ dsia: dsi@54300000 {
+ compatible = "nvidia,tegra114-dsi";
+ reg = <0x54300000 0x00040000>;
+ clocks = <&tegra_car TEGRA114_CLK_DSIA>,
+ <&tegra_car TEGRA114_CLK_DSIALP>,
+ <&tegra_car TEGRA114_CLK_PLL_D_OUT0>;
+ clock-names = "dsi", "lp", "parent";
+ resets = <&tegra_car 48>;
+ reset-names = "dsi";
+ nvidia,mipi-calibrate = <&mipi 0x060>; /* DSIA & DSIB pads */
+ };
new file mode 100644
@@ -0,0 +1,149 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra124-dpaux.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra DisplayPort AUX Interface
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+description: |
+ The Tegra Display Port Auxiliary (DPAUX) pad controller manages two
+ pins which can be assigned to either the DPAUX channel or to an I2C
+ controller.
+
+ When configured for DisplayPort AUX operation, the DPAUX controller
+ can also be used to communicate with a DisplayPort device using the
+ AUX channel.
+
+properties:
+ $nodename:
+ pattern: "^dpaux@[0-9a-f]+$"
+
+ compatible:
+ oneOf:
+ - enum:
+ - nvidia,tegra124-dpaux
+ - nvidia,tegra210-dpaux
+ - nvidia,tegra186-dpaux
+ - nvidia,tegra194-dpaux
+
+ - items:
+ - const: nvidia,tegra132-dpaux
+ - const: nvidia,tegra124-dpaux
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: clock input for the DPAUX hardware
+ - description: reference clock
+
+ clock-names:
+ items:
+ - const: dpaux
+ - const: parent
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: dpaux
+
+ power-domains:
+ maxItems: 1
+
+ i2c-bus:
+ description: Subnode where I2C slave devices are listed. This
+ subnode must be always present. If there are no I2C slave
+ devices, an empty node should be added. See ../../i2c/i2c.yaml
+ for more information.
+ type: object
+
+ vdd-supply:
+ description: phandle of a supply that powers the DisplayPort
+ link
+
+patternProperties:
+ "^pinmux-[a-z0-9]+$":
+ description:
+ Since only three configurations are possible, only three child
+ nodes are needed to describe the pin mux'ing options for the
+ DPAUX pads. Furthermore, given that the pad functions are only
+ applicable to a single set of pads, the child nodes only need
+ to describe the pad group the functions are being applied to
+ rather than the individual pads.
+ type: object
+ properties:
+ groups:
+ const: dpaux-io
+
+ function:
+ enum:
+ - aux
+ - i2c
+ - off
+
+ additionalProperties: false
+
+ required:
+ - groups
+ - function
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra210-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ dpaux: dpaux@545c0000 {
+ compatible = "nvidia,tegra210-dpaux";
+ reg = <0x545c0000 0x00040000>;
+ interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA210_CLK_DPAUX>,
+ <&tegra_car TEGRA210_CLK_PLL_DP>;
+ clock-names = "dpaux", "parent";
+ resets = <&tegra_car 181>;
+ reset-names = "dpaux";
+ power-domains = <&pd_sor>;
+ status = "disabled";
+
+ state_dpaux_aux: pinmux-aux {
+ groups = "dpaux-io";
+ function = "aux";
+ };
+
+ state_dpaux_i2c: pinmux-i2c {
+ groups = "dpaux-io";
+ function = "i2c";
+ };
+
+ state_dpaux_off: pinmux-off {
+ groups = "dpaux-io";
+ function = "off";
+ };
+
+ i2c-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
new file mode 100644
@@ -0,0 +1,206 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra124-sor.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra SOR Output Encoder
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+description: |
+ The Serial Output Resource (SOR) can be used to drive HDMI, LVDS, eDP
+ and DP outputs.
+
+properties:
+ $nodename:
+ pattern: "^sor@[0-9a-f]+$"
+
+ compatible:
+ oneOf:
+ - enum:
+ - nvidia,tegra124-sor
+ - nvidia,tegra210-sor
+ - nvidia,tegra210-sor1
+ - nvidia,tegra186-sor
+ - nvidia,tegra186-sor1
+ - nvidia,tegra194-sor
+
+ - items:
+ - const: nvidia,tegra132-sor
+ - const: nvidia,tegra124-sor
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ minItems: 5
+ maxItems: 6
+
+ clock-names:
+ minItems: 5
+ maxItems: 6
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: sor
+
+ power-domains:
+ maxItems: 1
+
+ avdd-io-hdmi-dp-supply:
+ description: I/O supply for HDMI/DP
+
+ vdd-hdmi-dp-pll-supply:
+ description: PLL supply for HDMI/DP
+
+ hdmi-supply:
+ description: +5.0V HDMI connector supply
+
+ # Tegra186 and later
+ nvidia,interface:
+ description: index of the SOR interface
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+ nvidia,ddc-i2c-bus:
+ description: phandle of an I2C controller used for DDC EDID
+ probing
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ nvidia,hpd-gpio:
+ description: specifies a GPIO used for hotplug detection
+ maxItems: 1
+
+ nvidia,edid:
+ description: supplies a binary EDID blob
+ $ref: "/schemas/types.yaml#/definitions/uint8-array"
+
+ nvidia,panel:
+ description: phandle of a display panel
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ nvidia,xbar-cfg:
+ description: 5 cells containing the crossbar configuration.
+ Each lane of the SOR, identified by the cell's index, is
+ mapped via the crossbar to the pad specified by the cell's
+ value.
+ $ref: "/schemas/types.yaml#/definitions/uint32-array"
+
+ # optional when driving an eDP output
+ nvidia,dpaux:
+ description: phandle to a DispayPort AUX interface
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - nvidia,tegra186-sor
+ - nvidia,tegra194-sor
+ then:
+ properties:
+ clocks:
+ items:
+ - description: clock input for the SOR hardware
+ - description: SOR output clock
+ - description: input for the pixel clock
+ - description: reference clock for the SOR clock
+ - description: safe reference clock for the SOR clock
+ during power up
+ - description: SOR pad output clock
+
+ clock-names:
+ items:
+ - const: sor
+ - enum:
+ - source # deprecated
+ - out
+ - const: parent
+ - const: dp
+ - const: safe
+ - const: pad
+ else:
+ properties:
+ clocks:
+ items:
+ - description: clock input for the SOR hardware
+ - description: SOR output clock
+ - description: input for the pixel clock
+ - description: reference clock for the SOR clock
+ - description: safe reference clock for the SOR clock
+ during power up
+
+ clock-names:
+ items:
+ - const: sor
+ - enum:
+ - source # deprecated
+ - out
+ - const: parent
+ - const: dp
+ - const: safe
+
+ - if:
+ not:
+ properties:
+ contains:
+ const: nvidia,panel
+ then:
+ required:
+ - hdmi-supply
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+ - avdd-io-hdmi-dp-supply
+ - vdd-hdmi-dp-pll-supply
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra210-car.h>
+ #include <dt-bindings/gpio/tegra-gpio.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ sor0: sor@54540000 {
+ compatible = "nvidia,tegra210-sor";
+ reg = <0x54540000 0x00040000>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA210_CLK_SOR0>,
+ <&tegra_car TEGRA210_CLK_SOR0_OUT>,
+ <&tegra_car TEGRA210_CLK_PLL_D_OUT0>,
+ <&tegra_car TEGRA210_CLK_PLL_DP>,
+ <&tegra_car TEGRA210_CLK_SOR_SAFE>;
+ clock-names = "sor", "out", "parent", "dp", "safe";
+ resets = <&tegra_car 182>;
+ reset-names = "sor";
+ pinctrl-0 = <&state_dpaux_aux>;
+ pinctrl-1 = <&state_dpaux_i2c>;
+ pinctrl-2 = <&state_dpaux_off>;
+ pinctrl-names = "aux", "i2c", "off";
+ power-domains = <&pd_sor>;
+
+ avdd-io-hdmi-dp-supply = <&avdd_1v05>;
+ vdd-hdmi-dp-pll-supply = <&vdd_1v8>;
+ hdmi-supply = <&vdd_hdmi>;
+
+ nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+ nvidia,hpd-gpio = <&gpio TEGRA_GPIO(CC, 1) GPIO_ACTIVE_LOW>;
+ };
new file mode 100644
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra124-vic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra Video Image Composer
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^vic@[0-9a-f]+$"
+
+ compatible:
+ oneOf:
+ - enum:
+ - nvidia,tegra124-vic
+ - nvidia,tegra210-vic
+ - nvidia,tegra186-vic
+ - nvidia,tegra194-vic
+
+ - items:
+ - const: nvidia,tegra132-vic
+ - const: nvidia,tegra124-vic
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: clock input for the VIC hardware
+
+ clock-names:
+ items:
+ - const: vic
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: vic
+
+ power-domains:
+ maxItems: 1
+
+ iommus:
+ maxItems: 1
+
+ interconnects:
+ description: Description of the interconnect paths for the VIC;
+ see ../interconnect/interconnect.txt for details.
+ items:
+ - description: memory read client for VIC
+ - description: memory write client for VIC
+
+ interconnect-names:
+ items:
+ - const: dma-mem # read
+ - const: write
+
+ dma-coherent: true
+
+additionalProperties: false
new file mode 100644
@@ -0,0 +1,85 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra186-dc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra186 (and later) Display Controller
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^display@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - nvidia,tegra186-dc
+ - nvidia,tegra194-dc
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: display controller pixel clock
+
+ clock-names:
+ items:
+ - const: dc
+
+ resets:
+ items:
+ - description: display controller reset
+
+ reset-names:
+ items:
+ - const: dc
+
+ power-domains:
+ maxItems: 1
+
+ iommus:
+ maxItems: 1
+
+ interconnects:
+ description: Description of the interconnect paths for the
+ display controller; see ../interconnect/interconnect.txt
+ for details.
+
+ interconnect-names:
+ items:
+ - const: dma-mem # read-0
+ - const: read-1
+
+ nvidia,outputs:
+ description: A list of phandles of outputs that this display
+ controller can drive.
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
+
+ nvidia,head:
+ description: The number of the display controller head. This
+ is used to setup the various types of output to receive
+ video data from the given head.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+ - power-domains
+ - nvidia,outputs
+ - nvidia,head
+
+# see nvidia,tegra186-display.yaml for examples
new file mode 100644
@@ -0,0 +1,310 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra186-display.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra186 (and later) Display Hub
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^display-hub@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - nvidia,tegra186-display
+ - nvidia,tegra194-display
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 1
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ minItems: 2
+ maxItems: 3
+
+ clock-names:
+ minItems: 2
+ maxItems: 3
+
+ resets:
+ items:
+ - description: display hub reset
+ - description: window group 0 reset
+ - description: window group 1 reset
+ - description: window group 2 reset
+ - description: window group 3 reset
+ - description: window group 4 reset
+ - description: window group 5 reset
+
+ reset-names:
+ items:
+ - const: misc
+ - const: wgrp0
+ - const: wgrp1
+ - const: wgrp2
+ - const: wgrp3
+ - const: wgrp4
+ - const: wgrp5
+
+ power-domains:
+ maxItems: 1
+
+ ranges:
+ maxItems: 1
+
+patternProperties:
+ "^display@[0-9a-f]+$":
+ type: object
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: nvidia,tegra186-display
+ then:
+ properties:
+ clocks:
+ items:
+ - description: display core clock
+ - description: display stream compression clock
+ - description: display hub clock
+
+ clock-names:
+ items:
+ - const: disp
+ - const: dsc
+ - const: hub
+ else:
+ properties:
+ clocks:
+ items:
+ - description: display core clock
+ - description: display hub clock
+
+ clock-names:
+ items:
+ - const: disp
+ - const: hub
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+ - power-domains
+ - "#address-cells"
+ - "#size-cells"
+ - ranges
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra186-clock.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/memory/tegra186-mc.h>
+ #include <dt-bindings/power/tegra186-powergate.h>
+ #include <dt-bindings/reset/tegra186-reset.h>
+
+ display-hub@15200000 {
+ compatible = "nvidia,tegra186-display";
+ reg = <0x15200000 0x00040000>;
+ resets = <&bpmp TEGRA186_RESET_NVDISPLAY0_MISC>,
+ <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP0>,
+ <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP1>,
+ <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP2>,
+ <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP3>,
+ <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP4>,
+ <&bpmp TEGRA186_RESET_NVDISPLAY0_WGRP5>;
+ reset-names = "misc", "wgrp0", "wgrp1", "wgrp2",
+ "wgrp3", "wgrp4", "wgrp5";
+ clocks = <&bpmp TEGRA186_CLK_NVDISPLAY_DISP>,
+ <&bpmp TEGRA186_CLK_NVDISPLAY_DSC>,
+ <&bpmp TEGRA186_CLK_NVDISPLAYHUB>;
+ clock-names = "disp", "dsc", "hub";
+ status = "disabled";
+
+ power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ranges = <0x15200000 0x15200000 0x40000>;
+
+ display@15200000 {
+ compatible = "nvidia,tegra186-dc";
+ reg = <0x15200000 0x10000>;
+ interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bpmp TEGRA186_CLK_NVDISPLAY_P0>;
+ clock-names = "dc";
+ resets = <&bpmp TEGRA186_RESET_NVDISPLAY0_HEAD0>;
+ reset-names = "dc";
+
+ power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+ interconnects = <&mc TEGRA186_MEMORY_CLIENT_NVDISPLAYR &emc>,
+ <&mc TEGRA186_MEMORY_CLIENT_NVDISPLAYR1 &emc>;
+ interconnect-names = "dma-mem", "read-1";
+ iommus = <&smmu TEGRA186_SID_NVDISPLAY>;
+
+ nvidia,outputs = <&dsia &dsib &sor0 &sor1>;
+ nvidia,head = <0>;
+ };
+
+ display@15210000 {
+ compatible = "nvidia,tegra186-dc";
+ reg = <0x15210000 0x10000>;
+ interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bpmp TEGRA186_CLK_NVDISPLAY_P1>;
+ clock-names = "dc";
+ resets = <&bpmp TEGRA186_RESET_NVDISPLAY0_HEAD1>;
+ reset-names = "dc";
+
+ power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISPB>;
+ interconnects = <&mc TEGRA186_MEMORY_CLIENT_NVDISPLAYR &emc>,
+ <&mc TEGRA186_MEMORY_CLIENT_NVDISPLAYR1 &emc>;
+ interconnect-names = "dma-mem", "read-1";
+ iommus = <&smmu TEGRA186_SID_NVDISPLAY>;
+
+ nvidia,outputs = <&dsia &dsib &sor0 &sor1>;
+ nvidia,head = <1>;
+ };
+
+ display@15220000 {
+ compatible = "nvidia,tegra186-dc";
+ reg = <0x15220000 0x10000>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bpmp TEGRA186_CLK_NVDISPLAY_P2>;
+ clock-names = "dc";
+ resets = <&bpmp TEGRA186_RESET_NVDISPLAY0_HEAD2>;
+ reset-names = "dc";
+
+ power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISPC>;
+ interconnects = <&mc TEGRA186_MEMORY_CLIENT_NVDISPLAYR &emc>,
+ <&mc TEGRA186_MEMORY_CLIENT_NVDISPLAYR1 &emc>;
+ interconnect-names = "dma-mem", "read-1";
+ iommus = <&smmu TEGRA186_SID_NVDISPLAY>;
+
+ nvidia,outputs = <&sor0 &sor1>;
+ nvidia,head = <2>;
+ };
+ };
+
+ - |
+ #include <dt-bindings/clock/tegra194-clock.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/memory/tegra194-mc.h>
+ #include <dt-bindings/power/tegra194-powergate.h>
+ #include <dt-bindings/reset/tegra194-reset.h>
+
+ display-hub@15200000 {
+ compatible = "nvidia,tegra194-display";
+ reg = <0x15200000 0x00040000>;
+ resets = <&bpmp TEGRA194_RESET_NVDISPLAY0_MISC>,
+ <&bpmp TEGRA194_RESET_NVDISPLAY0_WGRP0>,
+ <&bpmp TEGRA194_RESET_NVDISPLAY0_WGRP1>,
+ <&bpmp TEGRA194_RESET_NVDISPLAY0_WGRP2>,
+ <&bpmp TEGRA194_RESET_NVDISPLAY0_WGRP3>,
+ <&bpmp TEGRA194_RESET_NVDISPLAY0_WGRP4>,
+ <&bpmp TEGRA194_RESET_NVDISPLAY0_WGRP5>;
+ reset-names = "misc", "wgrp0", "wgrp1", "wgrp2",
+ "wgrp3", "wgrp4", "wgrp5";
+ clocks = <&bpmp TEGRA194_CLK_NVDISPLAY_DISP>,
+ <&bpmp TEGRA194_CLK_NVDISPLAYHUB>;
+ clock-names = "disp", "hub";
+ status = "disabled";
+
+ power-domains = <&bpmp TEGRA194_POWER_DOMAIN_DISP>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ranges = <0x15200000 0x15200000 0x40000>;
+
+ display@15200000 {
+ compatible = "nvidia,tegra194-dc";
+ reg = <0x15200000 0x10000>;
+ interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bpmp TEGRA194_CLK_NVDISPLAY_P0>;
+ clock-names = "dc";
+ resets = <&bpmp TEGRA194_RESET_NVDISPLAY0_HEAD0>;
+ reset-names = "dc";
+
+ power-domains = <&bpmp TEGRA194_POWER_DOMAIN_DISP>;
+ interconnects = <&mc TEGRA194_MEMORY_CLIENT_NVDISPLAYR &emc>,
+ <&mc TEGRA194_MEMORY_CLIENT_NVDISPLAYR1 &emc>;
+ interconnect-names = "dma-mem", "read-1";
+
+ nvidia,outputs = <&sor0 &sor1 &sor2 &sor3>;
+ nvidia,head = <0>;
+ };
+
+ display@15210000 {
+ compatible = "nvidia,tegra194-dc";
+ reg = <0x15210000 0x10000>;
+ interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bpmp TEGRA194_CLK_NVDISPLAY_P1>;
+ clock-names = "dc";
+ resets = <&bpmp TEGRA194_RESET_NVDISPLAY0_HEAD1>;
+ reset-names = "dc";
+
+ power-domains = <&bpmp TEGRA194_POWER_DOMAIN_DISPB>;
+ interconnects = <&mc TEGRA194_MEMORY_CLIENT_NVDISPLAYR &emc>,
+ <&mc TEGRA194_MEMORY_CLIENT_NVDISPLAYR1 &emc>;
+ interconnect-names = "dma-mem", "read-1";
+
+ nvidia,outputs = <&sor0 &sor1 &sor2 &sor3>;
+ nvidia,head = <1>;
+ };
+
+ display@15220000 {
+ compatible = "nvidia,tegra194-dc";
+ reg = <0x15220000 0x10000>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bpmp TEGRA194_CLK_NVDISPLAY_P2>;
+ clock-names = "dc";
+ resets = <&bpmp TEGRA194_RESET_NVDISPLAY0_HEAD2>;
+ reset-names = "dc";
+
+ power-domains = <&bpmp TEGRA194_POWER_DOMAIN_DISPC>;
+ interconnects = <&mc TEGRA194_MEMORY_CLIENT_NVDISPLAYR &emc>,
+ <&mc TEGRA194_MEMORY_CLIENT_NVDISPLAYR1 &emc>;
+ interconnect-names = "dma-mem", "read-1";
+
+ nvidia,outputs = <&sor0 &sor1 &sor2 &sor3>;
+ nvidia,head = <2>;
+ };
+
+ display@15230000 {
+ compatible = "nvidia,tegra194-dc";
+ reg = <0x15230000 0x10000>;
+ interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bpmp TEGRA194_CLK_NVDISPLAY_P3>;
+ clock-names = "dc";
+ resets = <&bpmp TEGRA194_RESET_NVDISPLAY0_HEAD3>;
+ reset-names = "dc";
+
+ power-domains = <&bpmp TEGRA194_POWER_DOMAIN_DISPC>;
+ interconnects = <&mc TEGRA194_MEMORY_CLIENT_NVDISPLAYR &emc>,
+ <&mc TEGRA194_MEMORY_CLIENT_NVDISPLAYR1 &emc>;
+ interconnect-names = "dma-mem", "read-1";
+
+ nvidia,outputs = <&sor0 &sor1 &sor2 &sor3>;
+ nvidia,head = <3>;
+ };
+ };
new file mode 100644
@@ -0,0 +1,46 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra186-dsi-padctl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra MIPI DSI pad controller
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^padctl@[0-9a-f]+$"
+
+ compatible:
+ const: nvidia,tegra186-dsi-padctl
+
+ reg:
+ maxItems: 1
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: dsi
+
+allOf:
+ - $ref: "/schemas/reset/reset.yaml"
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/reset/tegra186-reset.h>
+
+ padctl@15880000 {
+ compatible = "nvidia,tegra186-dsi-padctl";
+ reg = <0x15880000 0x10000>;
+ resets = <&bpmp TEGRA186_RESET_DSI>;
+ reset-names = "dsi";
+ };
+
new file mode 100644
@@ -0,0 +1,181 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra20-dc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra Display Controller
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^dc@[0-9a-f]+$"
+
+ compatible:
+ oneOf:
+ - enum:
+ - nvidia,tegra20-dc
+ - nvidia,tegra30-dc
+ - nvidia,tegra114-dc
+ - nvidia,tegra124-dc
+ - nvidia,tegra210-dc
+
+ - items:
+ - const: nvidia,tegra124-dc
+ - const: nvidia,tegra132-dc
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ minItems: 1
+ items:
+ - description: display controller pixel clock
+ - description: parent clock # optional
+
+ clock-names:
+ minItems: 1
+ items:
+ - const: dc
+ - const: parent # optional
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: dc
+
+ interconnect-names: true
+ interconnects: true
+
+ iommus:
+ maxItems: 1
+
+ operating-points-v2:
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ power-domains:
+ items:
+ - description: phandle to the core power domain
+
+ nvidia,head:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: The number of the display controller head. This is used to setup the various
+ types of output to receive video data from the given head.
+
+ nvidia,outputs:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description: A list of phandles of outputs that this display controller can drive.
+
+ rgb:
+ type: object
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - nvidia,tegra20-dc
+ - nvidia,tegra30-dc
+ - nvidia,tegra114-dc
+ then:
+ properties:
+ interconnects:
+ items:
+ - description: window A memory client
+ - description: window B memory client
+ - description: window B memory client (vertical filter)
+ - description: window C memory client
+ - description: cursor memory client
+
+ interconnect-names:
+ items:
+ - const: wina
+ - const: winb
+ - const: winb-vfilter
+ - const: winc
+ - const: cursor
+
+ rgb:
+ description: Each display controller node has a child node, named "rgb", that represents
+ the RGB output associated with the controller.
+ type: object
+ properties:
+ nvidia,ddc-i2c-bus:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: phandle of an I2C controller used for DDC EDID probing
+
+ nvidia,hpd-gpio:
+ description: specifies a GPIO used for hotplug detection
+ maxItems: 1
+
+ nvidia,edid:
+ $ref: /schemas/types.yaml#/definitions/uint8-array
+ description: supplies a binary EDID blob
+
+ nvidia,panel:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: phandle of a display panel
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - nvidia,tegra124-dc
+ then:
+ properties:
+ interconnects:
+ minItems: 4
+ items:
+ - description: window A memory client
+ - description: window B memory client
+ - description: window C memory client
+ - description: cursor memory client
+ - description: window D memory client
+ - description: window T memory client
+
+ interconnect-names:
+ minItems: 4
+ items:
+ - const: wina
+ - const: winb
+ - const: winc
+ - const: cursor
+ - const: wind
+ - const: wint
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra20-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ dc@54200000 {
+ compatible = "nvidia,tegra20-dc";
+ reg = <0x54200000 0x00040000>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA20_CLK_DISP1>;
+ clock-names = "dc";
+ resets = <&tegra_car 27>;
+ reset-names = "dc";
+ };
new file mode 100644
@@ -0,0 +1,159 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra20-dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra Display Serial Interface
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - nvidia,tegra20-dsi
+ - nvidia,tegra30-dsi
+ - nvidia,tegra114-dsi
+ - nvidia,tegra124-dsi
+ - nvidia,tegra210-dsi
+ - nvidia,tegra186-dsi
+
+ - items:
+ - const: nvidia,tegra132-dsi
+ - const: nvidia,tegra124-dsi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ minItems: 2
+ maxItems: 3
+
+ clock-names:
+ minItems: 2
+ maxItems: 3
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: dsi
+
+ operating-points-v2:
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ power-domains:
+ maxItems: 1
+
+ avdd-dsi-csi-supply:
+ description: phandle of a supply that powers the DSI controller
+
+ nvidia,mipi-calibrate:
+ description: Should contain a phandle and a specifier specifying
+ which pads are used by this DSI output and need to be
+ calibrated. See nvidia,tegra114-mipi.yaml for details.
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
+
+ nvidia,ddc-i2c-bus:
+ description: phandle of an I2C controller used for DDC EDID
+ probing
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ nvidia,hpd-gpio:
+ description: specifies a GPIO used for hotplug detection
+ maxItems: 1
+
+ nvidia,edid:
+ description: supplies a binary EDID blob
+ $ref: "/schemas/types.yaml#/definitions/uint8-array"
+
+ nvidia,panel:
+ description: phandle of a display panel
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ nvidia,ganged-mode:
+ description: contains a phandle to a second DSI controller to
+ gang up with in order to support up to 8 data lanes
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+allOf:
+ - $ref: "../dsi-controller.yaml#"
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - nvidia,tegra20-dsi
+ - nvidia,tegra30-dsi
+ then:
+ properties:
+ clocks:
+ items:
+ - description: DSI module clock
+ - description: input for the pixel clock
+
+ clock-names:
+ items:
+ - const: dsi
+ - const: parent
+ else:
+ properties:
+ clocks:
+ items:
+ - description: DSI module clock
+ - description: low-power module clock
+ - description: input for the pixel clock
+
+ clock-names:
+ items:
+ - const: dsi
+ - const: lp
+ - const: parent
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: nvidia,tegra186-dsi
+ then:
+ required:
+ - interrupts
+
+unevaluatedProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra186-clock.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/power/tegra186-powergate.h>
+ #include <dt-bindings/reset/tegra186-reset.h>
+
+ dsi@15300000 {
+ compatible = "nvidia,tegra186-dsi";
+ reg = <0x15300000 0x10000>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bpmp TEGRA186_CLK_DSI>,
+ <&bpmp TEGRA186_CLK_DSIA_LP>,
+ <&bpmp TEGRA186_CLK_PLLD>;
+ clock-names = "dsi", "lp", "parent";
+ resets = <&bpmp TEGRA186_RESET_DSI>;
+ reset-names = "dsi";
+
+ power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
+ };
new file mode 100644
@@ -0,0 +1,70 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra20-epp.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra Encoder Pre-Processor
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^epp@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - nvidia,tegra20-epp
+ - nvidia,tegra30-epp
+ - nvidia,tegra114-epp
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: epp
+
+ iommus:
+ maxItems: 1
+
+ interconnects:
+ maxItems: 4
+
+ interconnect-names:
+ maxItems: 4
+
+ operating-points-v2:
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ power-domains:
+ items:
+ - description: phandle to the core power domain
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra20-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ epp@540c0000 {
+ compatible = "nvidia,tegra20-epp";
+ reg = <0x540c0000 0x00040000>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA20_CLK_EPP>;
+ resets = <&tegra_car 19>;
+ reset-names = "epp";
+ };
new file mode 100644
@@ -0,0 +1,73 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra20-gr2d.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA 2D graphics engine
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^gr2d@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - nvidia,tegra20-gr2d
+ - nvidia,tegra30-gr2d
+ - nvidia,tegra114-gr2d
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: module clock
+
+ resets:
+ items:
+ - description: module reset
+ - description: memory client hotflush reset
+
+ reset-names:
+ items:
+ - const: 2d
+ - const: mc
+
+ iommus:
+ maxItems: 1
+
+ interconnects:
+ maxItems: 4
+
+ interconnect-names:
+ maxItems: 4
+
+ operating-points-v2:
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ power-domains:
+ items:
+ - description: phandle to the HEG or core power domain
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra20-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ gr2d@54140000 {
+ compatible = "nvidia,tegra20-gr2d";
+ reg = <0x54140000 0x00040000>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA20_CLK_GR2D>;
+ resets = <&tegra_car 21>;
+ reset-names = "2d";
+ };
new file mode 100644
@@ -0,0 +1,214 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra20-gr3d.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA 3D graphics engine
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^gr3d@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - nvidia,tegra20-gr3d
+ - nvidia,tegra30-gr3d
+ - nvidia,tegra114-gr3d
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ minItems: 1
+ maxItems: 2
+
+ clock-names:
+ minItems: 1
+ maxItems: 2
+
+ resets:
+ minItems: 2
+ maxItems: 4
+
+ reset-names:
+ minItems: 2
+ maxItems: 4
+
+ iommus:
+ minItems: 1
+ maxItems: 2
+
+ interconnects:
+ minItems: 4
+ maxItems: 10
+
+ interconnect-names:
+ minItems: 4
+ maxItems: 10
+
+ operating-points-v2:
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ power-domains:
+ minItems: 1
+ maxItems: 2
+
+ power-domain-names:
+ minItems: 2
+ maxItems: 2
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: nvidia,tegra20-gr2d
+ then:
+ properties:
+ clocks:
+ items:
+ - description: module clock
+
+ clock-names:
+ items:
+ - const: 3d
+
+ resets:
+ items:
+ - description: module reset
+ - description: memory client hotflush reset
+
+ reset-names:
+ items:
+ - const: 3d
+ - const: mc
+
+ iommus:
+ maxItems: 1
+
+ interconnects:
+ minItems: 4
+ maxItems: 4
+
+ interconnect-names:
+ minItems: 4
+ maxItems: 4
+
+ power-domains:
+ items:
+ - description: phandle to the TD power domain
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: nvidia,tegra30-gr3d
+ then:
+ properties:
+ clocks:
+ items:
+ - description: primary module clock
+ - description: secondary module clock
+
+ clock-names:
+ items:
+ - const: 3d
+ - const: 3d2
+
+ resets:
+ items:
+ - description: primary module reset
+ - description: secondary module reset
+ - description: primary memory client hotflush reset
+ - description: secondary memory client hotflush reset
+
+ reset-names:
+ items:
+ - const: 3d
+ - const: 3d2
+ - const: mc
+ - const: mc2
+
+ iommus:
+ minItems: 2
+ maxItems: 2
+
+ interconnects:
+ minItems: 8
+ maxItems: 8
+
+ interconnect-names:
+ minItems: 8
+ maxItems: 8
+
+ power-domains:
+ items:
+ - description: phandle to the TD power domain
+ - description: phandle to the TD2 power domain
+
+ power-domain-names:
+ items:
+ - const: 3d0
+ - const: 3d1
+
+ dependencies:
+ power-domains: [ power-domain-names ]
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: nvidia,tegra114-gr2d
+ then:
+ properties:
+ clocks:
+ items:
+ - description: module clock
+
+ clock-names:
+ items:
+ - const: 3d
+
+ resets:
+ items:
+ - description: module reset
+ - description: memory client hotflush reset
+
+ reset-names:
+ items:
+ - const: 3d
+ - const: mc
+
+ iommus:
+ maxItems: 1
+
+ interconnects:
+ minItems: 10
+ maxItems: 10
+
+ interconnect-names:
+ minItems: 10
+ maxItems: 10
+
+ power-domains:
+ items:
+ - description: phandle to the TD power domain
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra20-car.h>
+
+ gr3d@54180000 {
+ compatible = "nvidia,tegra20-gr3d";
+ reg = <0x54180000 0x00040000>;
+ clocks = <&tegra_car TEGRA20_CLK_GR3D>;
+ resets = <&tegra_car 24>;
+ reset-names = "3d";
+ };
new file mode 100644
@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra20-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra HDMI Output Encoder
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^hdmi@[0-9a-f]+$"
+
+ compatible:
+ oneOf:
+ - enum:
+ - nvidia,tegra20-hdmi
+ - nvidia,tegra30-hdmi
+ - nvidia,tegra114-hdmi
+ - nvidia,tegra124-hdmi
+
+ - items:
+ - const: nvidia,tegra132-hdmi
+ - const: nvidia,tegra124-hdmi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: module clock
+ - description: parent clock
+
+ clock-names:
+ items:
+ - const: hdmi
+ - const: parent
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: hdmi
+
+ operating-points-v2:
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ power-domains:
+ items:
+ - description: phandle to the core power domain
+
+ hdmi-supply:
+ description: supply for the +5V HDMI connector pin
+
+ vdd-supply:
+ description: regulator for supply voltage
+
+ pll-supply:
+ description: regulator for PLL
+
+ nvidia,ddc-i2c-bus:
+ description: phandle of an I2C controller used for DDC EDID
+ probing
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ nvidia,hpd-gpio:
+ description: specifies a GPIO used for hotplug detection
+ maxItems: 1
+
+ nvidia,edid:
+ description: supplies a binary EDID blob
+ $ref: "/schemas/types.yaml#/definitions/uint8-array"
+
+ nvidia,panel:
+ description: phandle of a display panel
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ "#sound-dai-cells":
+ const: 0
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+ - pll-supply
+ - vdd-supply
+ - nvidia,ddc-i2c-bus
+ - nvidia,hpd-gpio
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra124-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/gpio/tegra-gpio.h>
+
+ hdmi@54280000 {
+ compatible = "nvidia,tegra124-hdmi";
+ reg = <0x54280000 0x00040000>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA124_CLK_HDMI>,
+ <&tegra_car TEGRA124_CLK_PLL_D2_OUT0>;
+ clock-names = "hdmi", "parent";
+ resets = <&tegra_car 51>;
+ reset-names = "hdmi";
+
+ hdmi-supply = <&vdd_5v0_hdmi>;
+ pll-supply = <&vdd_hdmi_pll>;
+ vdd-supply = <&vdd_3v3_hdmi>;
+
+ nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+ nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+ };
deleted file mode 100644
@@ -1,675 +0,0 @@
-NVIDIA Tegra host1x
-
-Required properties:
-- compatible: "nvidia,tegra<chip>-host1x"
-- reg: Physical base address and length of the controller's registers.
- For pre-Tegra186, one entry describing the whole register area.
- For Tegra186, one entry for each entry in reg-names:
- "vm" - VM region assigned to Linux
- "hypervisor" - Hypervisor region (only if Linux acts as hypervisor)
-- interrupts: The interrupt outputs from the controller.
-- #address-cells: The number of cells used to represent physical base addresses
- in the host1x address space. Should be 1.
-- #size-cells: The number of cells used to represent the size of an address
- range in the host1x address space. Should be 1.
-- ranges: The mapping of the host1x address space to the CPU address space.
-- clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
-- resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
-- reset-names: Must include the following entries:
- - host1x
- - mc
-
-Optional properties:
-- operating-points-v2: See ../bindings/opp/opp.txt for details.
- - power-domains: Phandle to HEG or core power domain.
-
-For each opp entry in 'operating-points-v2' table of host1x and its modules:
-- opp-supported-hw: One bitfield indicating:
- On Tegra20: SoC process ID mask
- On Tegra30+: SoC speedo ID mask
-
- A bitwise AND is performed against the value and if any bit
- matches, the OPP gets enabled.
-
-Each host1x client module having to perform DMA through the Memory Controller
-should have the interconnect endpoints set to the Memory Client and External
-Memory respectively.
-
-The host1x top-level node defines a number of children, each representing one
-of the following host1x client modules:
-
-- mpe: video encoder
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-mpe"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - mpe
-
- Optional properties:
- - interconnects: Must contain entry for the MPE memory clients.
- - interconnect-names: Must include name of the interconnect path for each
- interconnect entry. Consult TRM documentation for information about
- available memory clients, see MEMORY CONTROLLER section.
- - operating-points-v2: See ../bindings/opp/opp.txt for details.
- - power-domains: Phandle to MPE power domain.
-
-- vi: video input
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-vi"
- - reg: Physical base address and length of the controller registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- - Tegra20/Tegra30/Tegra114/Tegra124:
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - vi
- - Tegra210:
- - power-domains: Must include venc powergate node as vi is in VE partition.
-
- ports (optional node)
- vi can have optional ports node and max 6 ports are supported. Each port
- should have single 'endpoint' child node. All port nodes are grouped under
- ports node. Please refer to the bindings defined in
- Documentation/devicetree/bindings/media/video-interfaces.txt
-
- csi (required node)
- Tegra210 has CSI part of VI sharing same host interface and register space.
- So, VI device node should have CSI child node.
-
- - csi: mipi csi interface to vi
-
- Required properties:
- - compatible: "nvidia,tegra210-csi"
- - reg: Physical base address offset to parent and length of the controller
- registers.
- - clocks: Must contain entries csi, cilab, cilcd, cile, csi_tpg clocks.
- See ../clocks/clock-bindings.txt for details.
- - power-domains: Must include sor powergate node as csicil is in
- SOR partition.
-
- channel (optional nodes)
- Maximum 6 channels are supported with each csi brick as either x4 or x2
- based on hw connectivity to sensor.
-
- Required properties:
- - reg: csi port number. Valid port numbers are 0 through 5.
- - nvidia,mipi-calibrate: Should contain a phandle and a specifier
- specifying which pads are used by this CSI port and need to be
- calibrated. See also ../display/tegra/nvidia,tegra114-mipi.txt.
-
- Each channel node must contain 2 port nodes which can be grouped
- under 'ports' node and each port should have a single child 'endpoint'
- node.
-
- ports node
- Please refer to the bindings defined in
- Documentation/devicetree/bindings/media/video-interfaces.txt
-
- ports node must contain below 2 port nodes.
- port@0 with single child 'endpoint' node always a sink.
- port@1 with single child 'endpoint' node always a source.
-
- port@0 (required node)
- Required properties:
- - reg: 0
-
- endpoint (required node)
- Required properties:
- - data-lanes: an array of data lane from 1 to 8. Valid array
- lengths are 1/2/4/8.
- - remote-endpoint: phandle to sensor 'endpoint' node.
-
- port@1 (required node)
- Required properties:
- - reg: 1
-
- endpoint (required node)
- Required properties:
- - remote-endpoint: phandle to vi port 'endpoint' node.
-
- Optional properties:
- - interconnects: Must contain entry for the VI memory clients.
- - interconnect-names: Must include name of the interconnect path for each
- interconnect entry. Consult TRM documentation for information about
- available memory clients, see MEMORY CONTROLLER section.
- - operating-points-v2: See ../bindings/opp/opp.txt for details.
- - power-domains: Phandle to VENC power domain.
-
-- epp: encoder pre-processor
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-epp"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - epp
-
- Optional properties:
- - interconnects: Must contain entry for the EPP memory clients.
- - interconnect-names: Must include name of the interconnect path for each
- interconnect entry. Consult TRM documentation for information about
- available memory clients, see MEMORY CONTROLLER section.
- - operating-points-v2: See ../bindings/opp/opp.txt for details.
- - power-domains: Phandle to HEG or core power domain.
-
-- isp: image signal processor
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-isp"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - isp
-
- Optional properties:
- - interconnects: Must contain entry for the ISP memory clients.
- - interconnect-names: Must include name of the interconnect path for each
- interconnect entry. Consult TRM documentation for information about
- available memory clients, see MEMORY CONTROLLER section.
- - power-domains: Phandle to VENC or core power domain.
-
-- gr2d: 2D graphics engine
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-gr2d"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - 2d
- - mc
-
- Optional properties:
- - interconnects: Must contain entry for the GR2D memory clients.
- - interconnect-names: Must include name of the interconnect path for each
- interconnect entry. Consult TRM documentation for information about
- available memory clients, see MEMORY CONTROLLER section.
- - operating-points-v2: See ../bindings/opp/opp.txt for details.
- - power-domains: Phandle to HEG or core power domain.
-
-- gr3d: 3D graphics engine
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-gr3d"
- - reg: Physical base address and length of the controller's registers.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- (This property may be omitted if the only clock in the list is "3d")
- - 3d
- This MUST be the first entry.
- - 3d2 (Only required on SoCs with two 3D clocks)
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - 3d
- - 3d2 (Only required on SoCs with two 3D clocks)
- - mc
- - mc2 (Only required on SoCs with two 3D clocks)
-
- Optional properties:
- - interconnects: Must contain entry for the GR3D memory clients.
- - interconnect-names: Must include name of the interconnect path for each
- interconnect entry. Consult TRM documentation for information about
- available memory clients, see MEMORY CONTROLLER section.
- - operating-points-v2: See ../bindings/opp/opp.txt for details.
- - power-domains: Phandles to 3D or core power domain.
-
-- dc: display controller
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-dc"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- - dc
- This MUST be the first entry.
- - parent
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - dc
- - nvidia,head: The number of the display controller head. This is used to
- setup the various types of output to receive video data from the given
- head.
-
- Each display controller node has a child node, named "rgb", that represents
- the RGB output associated with the controller. It can take the following
- optional properties:
- - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- - nvidia,edid: supplies a binary EDID blob
- - nvidia,panel: phandle of a display panel
- - interconnects: Must contain entry for the DC memory clients.
- - interconnect-names: Must include name of the interconnect path for each
- interconnect entry. Consult TRM documentation for information about
- available memory clients, see MEMORY CONTROLLER section.
- - operating-points-v2: See ../bindings/opp/opp.txt for details.
- - power-domains: Phandle to core power domain.
-
-- hdmi: High Definition Multimedia Interface
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-hdmi"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - hdmi-supply: supply for the +5V HDMI connector pin
- - vdd-supply: regulator for supply voltage
- - pll-supply: regulator for PLL
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- - hdmi
- This MUST be the first entry.
- - parent
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - hdmi
-
- Optional properties:
- - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- - nvidia,edid: supplies a binary EDID blob
- - nvidia,panel: phandle of a display panel
- - operating-points-v2: See ../bindings/opp/opp.txt for details.
-
-- tvo: TV encoder output
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-tvo"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain one entry, for the module clock.
- See ../clocks/clock-bindings.txt for details.
-
- Optional properties:
- - operating-points-v2: See ../bindings/opp/opp.txt for details.
- - power-domains: Phandle to core power domain.
-
-- dsi: display serial interface
-
- Required properties:
- - compatible: "nvidia,tegra<chip>-dsi"
- - reg: Physical base address and length of the controller's registers.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- - dsi
- This MUST be the first entry.
- - lp
- - parent
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - dsi
- - avdd-dsi-supply: phandle of a supply that powers the DSI controller
- - nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying
- which pads are used by this DSI output and need to be calibrated. See also
- ../display/tegra/nvidia,tegra114-mipi.txt.
-
- Optional properties:
- - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- - nvidia,edid: supplies a binary EDID blob
- - nvidia,panel: phandle of a display panel
- - nvidia,ganged-mode: contains a phandle to a second DSI controller to gang
- up with in order to support up to 8 data lanes
- - operating-points-v2: See ../bindings/opp/opp.txt for details.
-
-- sor: serial output resource
-
- Required properties:
- - compatible: Should be:
- - "nvidia,tegra124-sor": for Tegra124 and Tegra132
- - "nvidia,tegra132-sor": for Tegra132
- - "nvidia,tegra210-sor": for Tegra210
- - "nvidia,tegra210-sor1": for Tegra210
- - "nvidia,tegra186-sor": for Tegra186
- - "nvidia,tegra186-sor1": for Tegra186
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- - sor: clock input for the SOR hardware
- - out: SOR output clock
- - parent: input for the pixel clock
- - dp: reference clock for the SOR clock
- - safe: safe reference for the SOR clock during power up
-
- For Tegra186 and later:
- - pad: SOR pad output clock (on Tegra186 and later)
-
- Obsolete:
- - source: source clock for the SOR clock (obsolete, use "out" instead)
-
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - sor
-
- Required properties on Tegra186 and later:
- - nvidia,interface: index of the SOR interface
-
- Optional properties:
- - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- - nvidia,edid: supplies a binary EDID blob
- - nvidia,panel: phandle of a display panel
- - nvidia,xbar-cfg: 5 cells containing the crossbar configuration. Each lane
- of the SOR, identified by the cell's index, is mapped via the crossbar to
- the pad specified by the cell's value.
-
- Optional properties when driving an eDP output:
- - nvidia,dpaux: phandle to a DispayPort AUX interface
-
-- dpaux: DisplayPort AUX interface
- - compatible : Should contain one of the following:
- - "nvidia,tegra124-dpaux": for Tegra124 and Tegra132
- - "nvidia,tegra210-dpaux": for Tegra210
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- - dpaux: clock input for the DPAUX hardware
- - parent: reference clock
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - dpaux
- - vdd-supply: phandle of a supply that powers the DisplayPort link
- - i2c-bus: Subnode where I2C slave devices are listed. This subnode
- must be always present. If there are no I2C slave devices, an empty
- node should be added. See ../../i2c/i2c.txt for more information.
-
- See ../pinctrl/nvidia,tegra124-dpaux-padctl.txt for information
- regarding the DPAUX pad controller bindings.
-
-- vic: Video Image Compositor
- - compatible : "nvidia,tegra<chip>-vic"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: The interrupt outputs from the controller.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- - vic: clock input for the VIC hardware
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - vic
-
- Optional properties:
- - interconnects: Must contain entry for the VIC memory clients.
- - interconnect-names: Must include name of the interconnect path for each
- interconnect entry. Consult TRM documentation for information about
- available memory clients, see MEMORY CONTROLLER section.
-
-Example:
-
-/ {
- ...
-
- host1x {
- compatible = "nvidia,tegra20-host1x", "simple-bus";
- reg = <0x50000000 0x00024000>;
- interrupts = <0 65 0x04 /* mpcore syncpt */
- 0 67 0x04>; /* mpcore general */
- clocks = <&tegra_car TEGRA20_CLK_HOST1X>;
- resets = <&tegra_car 28>;
- reset-names = "host1x";
- operating-points-v2 = <&dvfs_opp_table>;
- power-domains = <&domain>;
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- ranges = <0x54000000 0x54000000 0x04000000>;
-
- mpe {
- compatible = "nvidia,tegra20-mpe";
- reg = <0x54040000 0x00040000>;
- interrupts = <0 68 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_MPE>;
- resets = <&tegra_car 60>;
- reset-names = "mpe";
- operating-points-v2 = <&dvfs_opp_table>;
- power-domains = <&domain>;
- };
-
- vi@54080000 {
- compatible = "nvidia,tegra210-vi";
- reg = <0x0 0x54080000 0x0 0x700>;
- interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
- assigned-clocks = <&tegra_car TEGRA210_CLK_VI>;
- assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>;
- operating-points-v2 = <&dvfs_opp_table>;
-
- clocks = <&tegra_car TEGRA210_CLK_VI>;
- power-domains = <&pd_venc>;
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- ranges = <0x0 0x0 0x54080000 0x2000>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- imx219_vi_in0: endpoint {
- remote-endpoint = <&imx219_csi_out0>;
- };
- };
- };
-
- csi@838 {
- compatible = "nvidia,tegra210-csi";
- reg = <0x838 0x1300>;
- assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>,
- <&tegra_car TEGRA210_CLK_CILCD>,
- <&tegra_car TEGRA210_CLK_CILE>,
- <&tegra_car TEGRA210_CLK_CSI_TPG>;
- assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>,
- <&tegra_car TEGRA210_CLK_PLL_P>,
- <&tegra_car TEGRA210_CLK_PLL_P>;
- assigned-clock-rates = <102000000>,
- <102000000>,
- <102000000>,
- <972000000>;
-
- clocks = <&tegra_car TEGRA210_CLK_CSI>,
- <&tegra_car TEGRA210_CLK_CILAB>,
- <&tegra_car TEGRA210_CLK_CILCD>,
- <&tegra_car TEGRA210_CLK_CILE>,
- <&tegra_car TEGRA210_CLK_CSI_TPG>;
- clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg";
- power-domains = <&pd_sor>;
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- channel@0 {
- reg = <0>;
- nvidia,mipi-calibrate = <&mipi 0x001>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- imx219_csi_in0: endpoint {
- data-lanes = <1 2>;
- remote-endpoint = <&imx219_out0>;
- };
- };
-
- port@1 {
- reg = <1>;
- imx219_csi_out0: endpoint {
- remote-endpoint = <&imx219_vi_in0>;
- };
- };
- };
- };
- };
- };
-
- epp {
- compatible = "nvidia,tegra20-epp";
- reg = <0x540c0000 0x00040000>;
- interrupts = <0 70 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_EPP>;
- resets = <&tegra_car 19>;
- reset-names = "epp";
- operating-points-v2 = <&dvfs_opp_table>;
- power-domains = <&domain>;
- };
-
- isp {
- compatible = "nvidia,tegra20-isp";
- reg = <0x54100000 0x00040000>;
- interrupts = <0 71 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_ISP>;
- resets = <&tegra_car 23>;
- reset-names = "isp";
- };
-
- gr2d {
- compatible = "nvidia,tegra20-gr2d";
- reg = <0x54140000 0x00040000>;
- interrupts = <0 72 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_GR2D>;
- resets = <&tegra_car 21>;
- reset-names = "2d";
- operating-points-v2 = <&dvfs_opp_table>;
- power-domains = <&domain>;
- };
-
- gr3d {
- compatible = "nvidia,tegra20-gr3d";
- reg = <0x54180000 0x00040000>;
- clocks = <&tegra_car TEGRA20_CLK_GR3D>;
- resets = <&tegra_car 24>;
- reset-names = "3d";
- operating-points-v2 = <&dvfs_opp_table>;
- power-domains = <&domain>;
- };
-
- dc@54200000 {
- compatible = "nvidia,tegra20-dc";
- reg = <0x54200000 0x00040000>;
- interrupts = <0 73 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_DISP1>,
- <&tegra_car TEGRA20_CLK_PLL_P>;
- clock-names = "dc", "parent";
- resets = <&tegra_car 27>;
- reset-names = "dc";
- operating-points-v2 = <&dvfs_opp_table>;
- power-domains = <&domain>;
-
- interconnects = <&mc TEGRA20_MC_DISPLAY0A &emc>,
- <&mc TEGRA20_MC_DISPLAY0B &emc>,
- <&mc TEGRA20_MC_DISPLAY0C &emc>,
- <&mc TEGRA20_MC_DISPLAYHC &emc>;
- interconnect-names = "wina",
- "winb",
- "winc",
- "cursor";
-
- rgb {
- status = "disabled";
- };
- };
-
- dc@54240000 {
- compatible = "nvidia,tegra20-dc";
- reg = <0x54240000 0x00040000>;
- interrupts = <0 74 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_DISP2>,
- <&tegra_car TEGRA20_CLK_PLL_P>;
- clock-names = "dc", "parent";
- resets = <&tegra_car 26>;
- reset-names = "dc";
- operating-points-v2 = <&dvfs_opp_table>;
- power-domains = <&domain>;
-
- interconnects = <&mc TEGRA20_MC_DISPLAY0AB &emc>,
- <&mc TEGRA20_MC_DISPLAY0BB &emc>,
- <&mc TEGRA20_MC_DISPLAY0CB &emc>,
- <&mc TEGRA20_MC_DISPLAYHCB &emc>;
- interconnect-names = "wina",
- "winb",
- "winc",
- "cursor";
-
- rgb {
- status = "disabled";
- };
- };
-
- hdmi {
- compatible = "nvidia,tegra20-hdmi";
- reg = <0x54280000 0x00040000>;
- interrupts = <0 75 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_HDMI>,
- <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
- clock-names = "hdmi", "parent";
- resets = <&tegra_car 51>;
- reset-names = "hdmi";
- status = "disabled";
- operating-points-v2 = <&dvfs_opp_table>;
- };
-
- tvo {
- compatible = "nvidia,tegra20-tvo";
- reg = <0x542c0000 0x00040000>;
- interrupts = <0 76 0x04>;
- clocks = <&tegra_car TEGRA20_CLK_TVO>;
- status = "disabled";
- operating-points-v2 = <&dvfs_opp_table>;
- };
-
- dsi {
- compatible = "nvidia,tegra20-dsi";
- reg = <0x54300000 0x00040000>;
- clocks = <&tegra_car TEGRA20_CLK_DSI>,
- <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
- clock-names = "dsi", "parent";
- resets = <&tegra_car 48>;
- reset-names = "dsi";
- status = "disabled";
- operating-points-v2 = <&dvfs_opp_table>;
- };
- };
-
- ...
-};
new file mode 100644
@@ -0,0 +1,347 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra20-host1x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra host1x controller
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+description: The host1x top-level node defines a number of children, each
+ representing one of the host1x client modules defined in this binding.
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - nvidia,tegra20-host1x
+ - nvidia,tegra30-host1x
+ - nvidia,tegra114-host1x
+ - nvidia,tegra124-host1x
+ - nvidia,tegra210-host1x
+ - nvidia,tegra186-host1x
+ - nvidia,tegra194-host1x
+
+ - items:
+ - const: nvidia,tegra132-host1x
+ - const: nvidia,tegra124-host1x
+
+ reg:
+ minItems: 1
+ maxItems: 2
+
+ reg-names:
+ minItems: 1
+ maxItems: 2
+
+ interrupts:
+ items:
+ - description: host1x syncpoint interrupt
+ - description: host1x general interrupt
+ minItems: 1
+
+ interrupt-names:
+ items:
+ - const: syncpt
+ - const: host1x
+ minItems: 1
+
+ '#address-cells':
+ description: The number of cells used to represent physical base addresses
+ in the host1x address space.
+ enum: [1, 2]
+
+ '#size-cells':
+ description: The number of cells used to represent the size of an address
+ range in the host1x address space.
+ enum: [1, 2]
+
+ ranges:
+ maxItems: 1
+
+ clocks:
+ description: Must contain one entry, for the module clock. See
+ ../clocks/clock-bindings.txt for details.
+
+ clock-names:
+ items:
+ - const: host1x
+
+ resets:
+ minItems: 1 # MC reset is optional on Tegra186 and later
+ items:
+ - description: module reset
+ - description: memory client hotflush reset
+
+ reset-names:
+ minItems: 1 # MC reset is optional on Tegra186 and later
+ items:
+ - const: host1x
+ - const: mc
+
+ iommus:
+ maxItems: 1
+
+ interconnects:
+ items:
+ - description: memory read client for host1x
+
+ interconnect-names:
+ items:
+ - const: dma-mem # read
+
+ operating-points-v2:
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ power-domains:
+ items:
+ - description: phandle to the HEG or core power domain
+
+required:
+ - compatible
+ - interrupts
+ - interrupt-names
+ - '#address-cells'
+ - '#size-cells'
+ - ranges
+ - reg
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+
+additionalProperties:
+ type: object
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - nvidia,tegra186-host1x
+ - nvidia,tegra194-host1x
+ then:
+ properties:
+ reg-names:
+ items:
+ - const: hypervisor
+ - const: vm
+
+ reg:
+ items:
+ - description: physical base address and length of the register
+ region assigned to the VM
+ - description: physical base address and length of the register
+ region used by the hypervisor
+
+ resets:
+ maxItems: 1
+
+ reset-names:
+ maxItems: 1
+
+ required:
+ - reg-names
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra20-car.h>
+ #include <dt-bindings/gpio/tegra-gpio.h>
+
+ host1x@50000000 {
+ compatible = "nvidia,tegra20-host1x";
+ reg = <0x50000000 0x00024000>;
+ interrupts = <0 65 0x04 /* mpcore syncpt */
+ 0 67 0x04>; /* mpcore general */
+ interrupt-names = "syncpt", "host1x";
+ clocks = <&tegra_car TEGRA20_CLK_HOST1X>;
+ clock-names = "host1x";
+ resets = <&tegra_car 28>;
+ reset-names = "host1x";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ranges = <0x54000000 0x54000000 0x04000000>;
+
+ mpe@54040000 {
+ compatible = "nvidia,tegra20-mpe";
+ reg = <0x54040000 0x00040000>;
+ interrupts = <0 68 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_MPE>;
+ resets = <&tegra_car 60>;
+ reset-names = "mpe";
+ };
+
+ vi@54080000 {
+ compatible = "nvidia,tegra20-vi";
+ reg = <0x54080000 0x00040000>;
+ interrupts = <0 69 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_VI>;
+ resets = <&tegra_car 100>;
+ reset-names = "vi";
+ };
+
+ epp@540c0000 {
+ compatible = "nvidia,tegra20-epp";
+ reg = <0x540c0000 0x00040000>;
+ interrupts = <0 70 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_EPP>;
+ resets = <&tegra_car 19>;
+ reset-names = "epp";
+ };
+
+ isp@54100000 {
+ compatible = "nvidia,tegra20-isp";
+ reg = <0x54100000 0x00040000>;
+ interrupts = <0 71 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_ISP>;
+ resets = <&tegra_car 23>;
+ reset-names = "isp";
+ };
+
+ gr2d@54140000 {
+ compatible = "nvidia,tegra20-gr2d";
+ reg = <0x54140000 0x00040000>;
+ interrupts = <0 72 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_GR2D>;
+ resets = <&tegra_car 21>;
+ reset-names = "2d";
+ };
+
+ gr3d@54180000 {
+ compatible = "nvidia,tegra20-gr3d";
+ reg = <0x54180000 0x00040000>;
+ clocks = <&tegra_car TEGRA20_CLK_GR3D>;
+ resets = <&tegra_car 24>;
+ reset-names = "3d";
+ };
+
+ dc@54200000 {
+ compatible = "nvidia,tegra20-dc";
+ reg = <0x54200000 0x00040000>;
+ interrupts = <0 73 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_DISP1>;
+ clock-names = "dc";
+ resets = <&tegra_car 27>;
+ reset-names = "dc";
+
+ rgb {
+ };
+ };
+
+ dc@54240000 {
+ compatible = "nvidia,tegra20-dc";
+ reg = <0x54240000 0x00040000>;
+ interrupts = <0 74 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_DISP2>;
+ clock-names = "dc";
+ resets = <&tegra_car 26>;
+ reset-names = "dc";
+
+ rgb {
+ };
+ };
+
+ hdmi@54280000 {
+ compatible = "nvidia,tegra20-hdmi";
+ reg = <0x54280000 0x00040000>;
+ interrupts = <0 75 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_HDMI>,
+ <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
+ clock-names = "hdmi", "parent";
+ resets = <&tegra_car 51>;
+ reset-names = "hdmi";
+
+ hdmi-supply = <&vdd_5v0_hdmi>;
+ pll-supply = <&vdd_hdmi_pll>;
+ vdd-supply = <&vdd_3v3_hdmi>;
+
+ nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+ nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+ };
+
+ tvo@542c0000 {
+ compatible = "nvidia,tegra20-tvo";
+ reg = <0x542c0000 0x00040000>;
+ interrupts = <0 76 0x04>;
+ clocks = <&tegra_car TEGRA20_CLK_TVO>;
+ };
+
+ dsi@54300000 {
+ compatible = "nvidia,tegra20-dsi";
+ reg = <0x54300000 0x00040000>;
+ clocks = <&tegra_car TEGRA20_CLK_DSI>,
+ <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
+ clock-names = "dsi", "parent";
+ resets = <&tegra_car 48>;
+ reset-names = "dsi";
+ };
+ };
+
+ - |
+ #include <dt-bindings/clock/tegra210-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/memory/tegra210-mc.h>
+
+ host1x@50000000 {
+ compatible = "nvidia,tegra210-host1x";
+ reg = <0x50000000 0x00024000>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, /* mpcore syncpt */
+ <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; /* mpcore general */
+ interrupt-names = "syncpt", "host1x";
+ clocks = <&tegra_car TEGRA210_CLK_HOST1X>;
+ clock-names = "host1x";
+ resets = <&tegra_car 28>;
+ reset-names = "host1x";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ranges = <0x54000000 0x54000000 0x01000000>;
+ iommus = <&mc TEGRA_SWGROUP_HC>;
+
+ vi@54080000 {
+ compatible = "nvidia,tegra210-vi";
+ reg = <0x54080000 0x00000700>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ assigned-clocks = <&tegra_car TEGRA210_CLK_VI>;
+ assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>;
+
+ clocks = <&tegra_car TEGRA210_CLK_VI>;
+ power-domains = <&pd_venc>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ranges = <0x0 0x54080000 0x2000>;
+
+ csi@838 {
+ compatible = "nvidia,tegra210-csi";
+ reg = <0x838 0x1300>;
+ assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>,
+ <&tegra_car TEGRA210_CLK_CILCD>,
+ <&tegra_car TEGRA210_CLK_CILE>,
+ <&tegra_car TEGRA210_CLK_CSI_TPG>;
+ assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>,
+ <&tegra_car TEGRA210_CLK_PLL_P>,
+ <&tegra_car TEGRA210_CLK_PLL_P>;
+ assigned-clock-rates = <102000000>,
+ <102000000>,
+ <102000000>,
+ <972000000>;
+
+ clocks = <&tegra_car TEGRA210_CLK_CSI>,
+ <&tegra_car TEGRA210_CLK_CILAB>,
+ <&tegra_car TEGRA210_CLK_CILCD>,
+ <&tegra_car TEGRA210_CLK_CILE>,
+ <&tegra_car TEGRA210_CLK_CSI_TPG>;
+ clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg";
+ power-domains = <&pd_sor>;
+ };
+ };
+ };
new file mode 100644
@@ -0,0 +1,67 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra20-isp.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra ISP processor
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ compatible:
+ enum:
+ - nvidia,tegra20-isp
+ - nvidia,tegra30-isp
+ - nvidia,tegra210-isp
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: module clock
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: isp
+
+ iommus:
+ maxItems: 1
+
+ interconnects:
+ items:
+ - description: memory write client
+
+ interconnect-names:
+ items:
+ - const: dma-mem # write
+
+ power-domains:
+ items:
+ - description: phandle to the VENC or core power domain
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra20-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ isp@54100000 {
+ compatible = "nvidia,tegra20-isp";
+ reg = <0x54100000 0x00040000>;
+ interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA20_CLK_ISP>;
+ resets = <&tegra_car 23>;
+ reset-names = "isp";
+ };
new file mode 100644
@@ -0,0 +1,73 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra20-mpe.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra Video Encoder
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^mpe@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - nvidia,tegra20-mpe
+ - nvidia,tegra30-mpe
+ - nvidia,tegra114-mpe
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: module clock
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: mpe
+
+ iommus:
+ maxItems: 1
+
+ interconnects:
+ minItems: 6
+ maxItems: 6
+
+ interconnect-names:
+ minItems: 6
+ maxItems: 6
+
+ operating-points-v2:
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ power-domains:
+ items:
+ - description: phandle to the MPE power domain
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra20-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ mpe@54040000 {
+ compatible = "nvidia,tegra20-mpe";
+ reg = <0x54040000 0x00040000>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA20_CLK_MPE>;
+ resets = <&tegra_car 60>;
+ reset-names = "mpe";
+ };
new file mode 100644
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra20-tvo.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra TV Encoder Output
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^tvo@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - nvidia,tegra20-tvo
+ - nvidia,tegra30-tvo
+ - nvidia,tegra114-tvo
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: module clock
+
+ operating-points-v2:
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ power-domains:
+ items:
+ - description: phandle to the core power domain
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra20-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ tvo@542c0000 {
+ compatible = "nvidia,tegra20-tvo";
+ reg = <0x542c0000 0x00040000>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA20_CLK_TVO>;
+ };
new file mode 100644
@@ -0,0 +1,163 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra20-vi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra Video Input controller
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^vi@[0-9a-f]+$"
+
+ compatible:
+ oneOf:
+ - const: nvidia,tegra20-vi
+ - const: nvidia,tegra30-vi
+ - const: nvidia,tegra114-vi
+ - const: nvidia,tegra124-vi
+ - items:
+ - const: nvidia,tegra132-vi
+ - const: nvidia,tegra124-vi
+ - const: nvidia,tegra210-vi
+ - const: nvidia,tegra186-vi
+ - const: nvidia,tegra194-vi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ items:
+ - description: module reset
+
+ reset-names:
+ items:
+ - const: vi
+
+ iommus:
+ maxItems: 1
+
+ interconnects:
+ minItems: 4
+ maxItems: 5
+
+ interconnect-names:
+ minItems: 4
+ maxItems: 5
+
+ operating-points-v2:
+ $ref: "/schemas/types.yaml#/definitions/phandle"
+
+ power-domains:
+ items:
+ - description: phandle to the VENC power domain
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 1
+
+ ranges:
+ maxItems: 1
+
+ avdd-dsi-csi-supply:
+ description: DSI/CSI power supply. Must supply 1.2 V.
+
+patternProperties:
+ "^csi@[0-9a-f]+$":
+ type: object
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - nvidia,tegra20-vi
+ - nvidia,tegra30-vi
+ - nvidia,tegra114-vi
+ - nvidia,tegra124-vi
+ then:
+ required:
+ - resets
+ - reset-names
+ else:
+ required:
+ - power-domains
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra20-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ vi@54080000 {
+ compatible = "nvidia,tegra20-vi";
+ reg = <0x54080000 0x00040000>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&tegra_car TEGRA20_CLK_VI>;
+ resets = <&tegra_car 100>;
+ reset-names = "vi";
+ };
+
+ - |
+ #include <dt-bindings/clock/tegra210-car.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ vi@54080000 {
+ compatible = "nvidia,tegra210-vi";
+ reg = <0x54080000 0x00000700>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ assigned-clocks = <&tegra_car TEGRA210_CLK_VI>;
+ assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>;
+
+ clocks = <&tegra_car TEGRA210_CLK_VI>;
+ power-domains = <&pd_venc>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ranges = <0x0 0x54080000 0x2000>;
+
+ csi@838 {
+ compatible = "nvidia,tegra210-csi";
+ reg = <0x838 0x1300>;
+ assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>,
+ <&tegra_car TEGRA210_CLK_CILCD>,
+ <&tegra_car TEGRA210_CLK_CILE>,
+ <&tegra_car TEGRA210_CLK_CSI_TPG>;
+ assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>,
+ <&tegra_car TEGRA210_CLK_PLL_P>,
+ <&tegra_car TEGRA210_CLK_PLL_P>;
+ assigned-clock-rates = <102000000>,
+ <102000000>,
+ <102000000>,
+ <972000000>;
+
+ clocks = <&tegra_car TEGRA210_CLK_CSI>,
+ <&tegra_car TEGRA210_CLK_CILAB>,
+ <&tegra_car TEGRA210_CLK_CILCD>,
+ <&tegra_car TEGRA210_CLK_CILE>,
+ <&tegra_car TEGRA210_CLK_CSI_TPG>;
+ clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg";
+ power-domains = <&pd_sor>;
+ };
+ };
new file mode 100644
@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/tegra/nvidia,tegra210-csi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra CSI controller
+
+maintainers:
+ - Thierry Reding <thierry.reding@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+
+properties:
+ $nodename:
+ pattern: "^csi@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - nvidia,tegra210-csi
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: module clock
+ - description: A/B lanes clock
+ - description: C/D lanes clock
+ - description: E lane clock
+ - description: test pattern generator clock
+
+ clock-names:
+ items:
+ - const: csi
+ - const: cilab
+ - const: cilcd
+ - const: cile
+ - const: csi_tpg
+
+ power-domains:
+ maxItems: 1
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - power-domains
+
+# see nvidia,tegra20-vi.yaml for an example
deleted file mode 100644
@@ -1,59 +0,0 @@
-Device tree binding for NVIDIA Tegra DPAUX pad controller
-========================================================
-
-The Tegra Display Port Auxiliary (DPAUX) pad controller manages two pins
-which can be assigned to either the DPAUX channel or to an I2C
-controller.
-
-This document defines the device-specific binding for the DPAUX pad
-controller. Refer to pinctrl-bindings.txt in this directory for generic
-information about pin controller device tree bindings. Please refer to
-the binding document ../display/tegra/nvidia,tegra20-host1x.txt for more
-details on the DPAUX binding.
-
-Pin muxing:
------------
-
-Child nodes contain the pinmux configurations following the conventions
-from the pinctrl-bindings.txt document.
-
-Since only three configurations are possible, only three child nodes are
-needed to describe the pin mux'ing options for the DPAUX pads.
-Furthermore, given that the pad functions are only applicable to a
-single set of pads, the child nodes only need to describe the pad group
-the functions are being applied to rather than the individual pads.
-
-Required properties:
-- groups: Must be "dpaux-io"
-- function: Must be either "aux", "i2c" or "off".
-
-Example:
---------
-
- dpaux@545c0000 {
- ...
-
- state_dpaux_aux: pinmux-aux {
- groups = "dpaux-io";
- function = "aux";
- };
-
- state_dpaux_i2c: pinmux-i2c {
- groups = "dpaux-io";
- function = "i2c";
- };
-
- state_dpaux_off: pinmux-off {
- groups = "dpaux-io";
- function = "off";
- };
- };
-
- ...
-
- i2c@7000d100 {
- ...
- pinctrl-0 = <&state_dpaux_i2c>;
- pinctrl-1 = <&state_dpaux_off>;
- pinctrl-names = "default", "idle";
- };