@@ -100,6 +100,19 @@ config DRM_LONTIUM_LT8912B
Say M here if you want to support this hardware as a module.
The module will be named "lontium-lt8912b".
+config DRM_LONTIUM_LT9211
+ tristate "Lontium LT9211 DSI/LVDS/DPI bridge"
+ depends on OF
+ select DRM_PANEL_BRIDGE
+ select DRM_KMS_HELPER
+ select DRM_MIPI_DSI
+ select REGMAP_I2C
+ help
+ Driver for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI
+ input to Single-link/Dual-Link DSI/LVDS or Single DPI output bridge
+ chip.
+ Please say Y if you have such hardware.
+
config DRM_LONTIUM_LT9611
tristate "Lontium LT9611 DSI/HDMI bridge"
select SND_SOC_HDMI_CODEC if SND_SOC
@@ -6,6 +6,7 @@ obj-$(CONFIG_DRM_CROS_EC_ANX7688) += cros-ec-anx7688.o
obj-$(CONFIG_DRM_DISPLAY_CONNECTOR) += display-connector.o
obj-$(CONFIG_DRM_ITE_IT6505) += ite-it6505.o
obj-$(CONFIG_DRM_LONTIUM_LT8912B) += lontium-lt8912b.o
+obj-$(CONFIG_DRM_LONTIUM_LT9211) += lontium-lt9211.o
obj-$(CONFIG_DRM_LONTIUM_LT9611) += lontium-lt9611.o
obj-$(CONFIG_DRM_LONTIUM_LT9611UXC) += lontium-lt9611uxc.o
obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o
new file mode 100644
@@ -0,0 +1,802 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Lontium LT9211 bridge driver
+ *
+ * LT9211 is capable of converting:
+ * 2xDSI/2xLVDS/1xDPI -> 2xDSI/2xLVDS/1xDPI
+ * Currently supported is:
+ * 1xDSI -> 1xLVDS
+ *
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_graph.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_of.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+#include <drm/drm_probe_helper.h>
+
+#define REG_PAGE_CONTROL 0xff
+#define REG_CHIPID0 0x8100
+#define REG_CHIPID0_VALUE 0x18
+#define REG_CHIPID1 0x8101
+#define REG_CHIPID1_VALUE 0x01
+#define REG_CHIPID2 0x8102
+#define REG_CHIPID2_VALUE 0xe3
+
+#define REG_DSI_LANE 0xd000
+/* DSI lane count - 0 means 4 lanes ; 1, 2, 3 means 1, 2, 3 lanes. */
+#define REG_DSI_LANE_COUNT(n) ((n) & 3)
+
+struct lt9211 {
+ struct drm_bridge bridge;
+ struct device *dev;
+ struct regmap *regmap;
+ struct mipi_dsi_device *dsi;
+ struct drm_bridge *panel_bridge;
+ struct gpio_desc *reset_gpio;
+ struct regulator *vccio;
+ bool lvds_dual_link;
+ bool lvds_dual_link_even_odd_swap;
+};
+
+static const struct regmap_range lt9211_rw_ranges[] = {
+ regmap_reg_range(0xff, 0xff),
+ regmap_reg_range(0x8100, 0x816b),
+ regmap_reg_range(0x8200, 0x82aa),
+ regmap_reg_range(0x8500, 0x85ff),
+ regmap_reg_range(0x8600, 0x86a0),
+ regmap_reg_range(0x8700, 0x8746),
+ regmap_reg_range(0xd000, 0xd0a7),
+ regmap_reg_range(0xd400, 0xd42c),
+ regmap_reg_range(0xd800, 0xd838),
+ regmap_reg_range(0xd9c0, 0xd9d5),
+};
+
+static const struct regmap_access_table lt9211_rw_table = {
+ .yes_ranges = lt9211_rw_ranges,
+ .n_yes_ranges = ARRAY_SIZE(lt9211_rw_ranges),
+};
+
+static const struct regmap_range_cfg lt9211_range = {
+ .name = "lt9211",
+ .range_min = 0x0000,
+ .range_max = 0xda00,
+ .selector_reg = REG_PAGE_CONTROL,
+ .selector_mask = 0xff,
+ .selector_shift = 0,
+ .window_start = 0,
+ .window_len = 0x100,
+};
+
+static const struct regmap_config lt9211_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .rd_table = <9211_rw_table,
+ .wr_table = <9211_rw_table,
+ .volatile_table = <9211_rw_table,
+ .ranges = <9211_range,
+ .num_ranges = 1,
+ .cache_type = REGCACHE_RBTREE,
+ .max_register = 0xda00,
+};
+
+static struct lt9211 *bridge_to_lt9211(struct drm_bridge *bridge)
+{
+ return container_of(bridge, struct lt9211, bridge);
+}
+
+static int lt9211_attach(struct drm_bridge *bridge,
+ enum drm_bridge_attach_flags flags)
+{
+ struct lt9211 *ctx = bridge_to_lt9211(bridge);
+
+ return drm_bridge_attach(bridge->encoder, ctx->panel_bridge,
+ &ctx->bridge, flags);
+}
+
+static int lt9211_read_chipid(struct lt9211 *ctx)
+{
+ u8 chipid[3];
+ int ret;
+
+ /* Read Chip ID registers and verify the chip can communicate. */
+ ret = regmap_bulk_read(ctx->regmap, REG_CHIPID0, chipid, 3);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to read Chip ID: %d\n", ret);
+ return ret;
+ }
+
+ /* Test for known Chip ID. */
+ if (chipid[0] != REG_CHIPID0_VALUE || chipid[1] != REG_CHIPID1_VALUE ||
+ chipid[2] != REG_CHIPID2_VALUE) {
+ dev_err(ctx->dev, "Unknown Chip ID: 0x%02x 0x%02x 0x%02x\n",
+ chipid[0], chipid[1], chipid[2]);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int lt9211_system_init(struct lt9211 *ctx)
+{
+ const struct reg_sequence lt9211_system_init_seq[] = {
+ { 0x8201, 0x18 },
+ { 0x8606, 0x61 },
+ { 0x8607, 0xa8 },
+ { 0x8714, 0x08 },
+ { 0x8715, 0x00 },
+ { 0x8718, 0x0f },
+ { 0x8722, 0x08 },
+ { 0x8723, 0x00 },
+ { 0x8726, 0x0f },
+ { 0x810b, 0xfe },
+ };
+
+ return regmap_multi_reg_write(ctx->regmap, lt9211_system_init_seq,
+ ARRAY_SIZE(lt9211_system_init_seq));
+}
+
+static int lt9211_configure_rx(struct lt9211 *ctx)
+{
+ const struct reg_sequence lt9211_rx_phy_seq[] = {
+ { 0x8202, 0x44 },
+ { 0x8204, 0xa0 },
+ { 0x8205, 0x22 },
+ { 0x8207, 0x9f },
+ { 0x8208, 0xfc },
+ /* ORR with 0xf8 here to enable DSI DN/DP swap. */
+ { 0x8209, 0x01 },
+ { 0x8217, 0x0c },
+ { 0x8633, 0x1b },
+ };
+
+ const struct reg_sequence lt9211_rx_cal_reset_seq[] = {
+ { 0x8120, 0x7f },
+ { 0x8120, 0xff },
+ };
+
+ const struct reg_sequence lt9211_rx_dig_seq[] = {
+ { 0x8630, 0x85 },
+ /* 0x8588: BIT 6 set = MIPI-RX, BIT 4 unset = LVDS-TX */
+ { 0x8588, 0x40 },
+ { 0x85ff, 0xd0 },
+ { REG_DSI_LANE, REG_DSI_LANE_COUNT(ctx->dsi->lanes) },
+ { 0xd002, 0x05 },
+ };
+
+ const struct reg_sequence lt9211_rx_div_reset_seq[] = {
+ { 0x810a, 0xc0 },
+ { 0x8120, 0xbf },
+ };
+
+ const struct reg_sequence lt9211_rx_div_clear_seq[] = {
+ { 0x810a, 0xc1 },
+ { 0x8120, 0xff },
+ };
+
+ int ret;
+
+ ret = regmap_multi_reg_write(ctx->regmap, lt9211_rx_phy_seq,
+ ARRAY_SIZE(lt9211_rx_phy_seq));
+ if (ret)
+ return ret;
+
+ ret = regmap_multi_reg_write(ctx->regmap, lt9211_rx_cal_reset_seq,
+ ARRAY_SIZE(lt9211_rx_cal_reset_seq));
+ if (ret)
+ return ret;
+
+ ret = regmap_multi_reg_write(ctx->regmap, lt9211_rx_dig_seq,
+ ARRAY_SIZE(lt9211_rx_dig_seq));
+ if (ret)
+ return ret;
+
+ ret = regmap_multi_reg_write(ctx->regmap, lt9211_rx_div_reset_seq,
+ ARRAY_SIZE(lt9211_rx_div_reset_seq));
+ if (ret)
+ return ret;
+
+ usleep_range(10000, 15000);
+
+ return regmap_multi_reg_write(ctx->regmap, lt9211_rx_div_clear_seq,
+ ARRAY_SIZE(lt9211_rx_div_clear_seq));
+}
+
+static int lt9211_autodetect_rx(struct lt9211 *ctx,
+ const struct drm_display_mode *mode)
+{
+ u16 width, height;
+ u32 byteclk;
+ u8 buf[5];
+ u8 format;
+ u8 bc[3];
+ int ret;
+
+ /* Measure ByteClock frequency. */
+ ret = regmap_write(ctx->regmap, 0x8600, 0x01);
+ if (ret)
+ return ret;
+
+ /* Give the chip time to lock onto RX stream. */
+ msleep(100);
+
+ /* Read the ByteClock frequency from the chip. */
+ ret = regmap_bulk_read(ctx->regmap, 0x8608, bc, sizeof(bc));
+ if (ret)
+ return ret;
+
+ /* RX ByteClock in kHz */
+ byteclk = ((bc[0] & 0xf) << 16) | (bc[1] << 8) | bc[2];
+
+ /* Width/Height/Format Auto-detection */
+ ret = regmap_bulk_read(ctx->regmap, 0xd082, buf, sizeof(buf));
+ if (ret)
+ return ret;
+
+ width = (buf[0] << 8) | buf[1];
+ height = (buf[3] << 8) | buf[4];
+ format = buf[2] & 0xf;
+
+ if (format == 0x3) { /* YUV422 16bit */
+ width /= 2;
+ } else if (format == 0xa) { /* RGB888 24bit */
+ width /= 3;
+ } else {
+ dev_err(ctx->dev, "Unsupported DSI pixel format 0x%01x\n",
+ format);
+ return -EINVAL;
+ }
+
+ if (width != mode->hdisplay) {
+ dev_err(ctx->dev,
+ "RX: Detected DSI width (%d) does not match mode hdisplay (%d)\n",
+ width, mode->hdisplay);
+ return -EINVAL;
+ }
+
+ if (height != mode->vdisplay) {
+ dev_err(ctx->dev,
+ "RX: Detected DSI height (%d) does not match mode vdisplay (%d)\n",
+ height, mode->vdisplay);
+ return -EINVAL;
+ }
+
+ dev_dbg(ctx->dev, "RX: %dx%d format=0x%01x byteclock=%d kHz\n",
+ width, height, format, byteclk);
+
+ return 0;
+}
+
+static int lt9211_configure_timing(struct lt9211 *ctx,
+ const struct drm_display_mode *mode)
+{
+ const struct reg_sequence lt9211_timing[] = {
+ { 0xd00d, (mode->vtotal >> 8) & 0xff },
+ { 0xd00e, mode->vtotal & 0xff },
+ { 0xd00f, (mode->vdisplay >> 8) & 0xff },
+ { 0xd010, mode->vdisplay & 0xff },
+ { 0xd011, (mode->htotal >> 8) & 0xff },
+ { 0xd012, mode->htotal & 0xff },
+ { 0xd013, (mode->hdisplay >> 8) & 0xff },
+ { 0xd014, mode->hdisplay & 0xff },
+ { 0xd015, (mode->vsync_end - mode->vsync_start) & 0xff },
+ { 0xd016, (mode->hsync_end - mode->hsync_start) & 0xff },
+ { 0xd017, ((mode->vsync_start - mode->vdisplay) >> 8) & 0xff },
+ { 0xd018, (mode->vsync_start - mode->vdisplay) & 0xff },
+ { 0xd019, ((mode->hsync_start - mode->hdisplay) >> 8) & 0xff },
+ { 0xd01a, (mode->hsync_start - mode->hdisplay) & 0xff },
+ };
+
+ return regmap_multi_reg_write(ctx->regmap, lt9211_timing,
+ ARRAY_SIZE(lt9211_timing));
+}
+
+static int lt9211_configure_plls(struct lt9211 *ctx,
+ const struct drm_display_mode *mode)
+{
+ const struct reg_sequence lt9211_pcr_seq[] = {
+ { 0xd026, 0x17 },
+ { 0xd027, 0xc3 },
+ { 0xd02d, 0x30 },
+ { 0xd031, 0x10 },
+ { 0xd023, 0x20 },
+ { 0xd038, 0x02 },
+ { 0xd039, 0x10 },
+ { 0xd03a, 0x20 },
+ { 0xd03b, 0x60 },
+ { 0xd03f, 0x04 },
+ { 0xd040, 0x08 },
+ { 0xd041, 0x10 },
+ { 0x810b, 0xee },
+ { 0x810b, 0xfe },
+ };
+
+ unsigned int pval;
+ int ret;
+
+ /* DeSSC PLL reference clock is 25 MHz XTal. */
+ ret = regmap_write(ctx->regmap, 0x822d, 0x48);
+ if (ret)
+ return ret;
+
+ if (mode->clock < 44000) {
+ ret = regmap_write(ctx->regmap, 0x8235, 0x83);
+ } else if (mode->clock < 88000) {
+ ret = regmap_write(ctx->regmap, 0x8235, 0x82);
+ } else if (mode->clock < 176000) {
+ ret = regmap_write(ctx->regmap, 0x8235, 0x81);
+ } else {
+ dev_err(ctx->dev,
+ "Unsupported mode clock (%d kHz) above 176 MHz.\n",
+ mode->clock);
+ return -EINVAL;
+ }
+
+ if (ret)
+ return ret;
+
+ /* Wait for the DeSSC PLL to stabilize. */
+ msleep(100);
+
+ ret = regmap_multi_reg_write(ctx->regmap, lt9211_pcr_seq,
+ ARRAY_SIZE(lt9211_pcr_seq));
+ if (ret)
+ return ret;
+
+ /* PCR stability test takes seconds. */
+ ret = regmap_read_poll_timeout(ctx->regmap, 0xd087, pval, pval & 0x8,
+ 20000, 10000000);
+ if (ret)
+ dev_err(ctx->dev, "PCR unstable, ret=%i\n", ret);
+
+ return ret;
+}
+
+static int lt9211_configure_tx(struct lt9211 *ctx, bool jeida,
+ bool bpp24, bool de)
+{
+ const struct reg_sequence system_lt9211_tx_phy_seq[] = {
+ /* DPI output disable */
+ { 0x8262, 0x00 },
+ /* BIT(7) is LVDS dual-port */
+ { 0x823b, 0x38 | (ctx->lvds_dual_link ? BIT(7) : 0) },
+ { 0x823e, 0x92 },
+ { 0x823f, 0x48 },
+ { 0x8240, 0x31 },
+ { 0x8243, 0x80 },
+ { 0x8244, 0x00 },
+ { 0x8245, 0x00 },
+ { 0x8249, 0x00 },
+ { 0x824a, 0x01 },
+ { 0x824e, 0x00 },
+ { 0x824f, 0x00 },
+ { 0x8250, 0x00 },
+ { 0x8253, 0x00 },
+ { 0x8254, 0x01 },
+ /* LVDS channel order, Odd:Even 0x10..A:B, 0x40..B:A */
+ { 0x8646, ctx->lvds_dual_link_even_odd_swap ? 0x40 : 0x10 },
+ { 0x8120, 0x7b },
+ { 0x816b, 0xff },
+ };
+
+ const struct reg_sequence system_lt9211_tx_dig_seq[] = {
+ { 0x8559, 0x40 | (jeida ? BIT(7) : 0) |
+ (de ? BIT(5) : 0) | (bpp24 ? BIT(4) : 0) },
+ { 0x855a, 0xaa },
+ { 0x855b, 0xaa },
+ { 0x855c, ctx->lvds_dual_link ? BIT(0) : 0 },
+ { 0x85a1, 0x77 },
+ { 0x8640, 0x40 },
+ { 0x8641, 0x34 },
+ { 0x8642, 0x10 },
+ { 0x8643, 0x23 },
+ { 0x8644, 0x41 },
+ { 0x8645, 0x02 },
+ };
+
+ const struct reg_sequence system_lt9211_tx_pll_seq[] = {
+ /* TX PLL power down */
+ { 0x8236, 0x01 },
+ { 0x8237, ctx->lvds_dual_link ? 0x2a : 0x29 },
+ { 0x8238, 0x06 },
+ { 0x8239, 0x30 },
+ { 0x823a, 0x8e },
+ { 0x8737, 0x14 },
+ { 0x8713, 0x00 },
+ { 0x8713, 0x80 },
+ };
+
+ unsigned int pval;
+ int ret;
+
+ ret = regmap_multi_reg_write(ctx->regmap, system_lt9211_tx_phy_seq,
+ ARRAY_SIZE(system_lt9211_tx_phy_seq));
+ if (ret)
+ return ret;
+
+ ret = regmap_multi_reg_write(ctx->regmap, system_lt9211_tx_dig_seq,
+ ARRAY_SIZE(system_lt9211_tx_dig_seq));
+ if (ret)
+ return ret;
+
+ ret = regmap_multi_reg_write(ctx->regmap, system_lt9211_tx_pll_seq,
+ ARRAY_SIZE(system_lt9211_tx_pll_seq));
+ if (ret)
+ return ret;
+
+ ret = regmap_read_poll_timeout(ctx->regmap, 0x871f, pval, pval & 0x80,
+ 10000, 1000000);
+ if (ret) {
+ dev_err(ctx->dev, "TX PLL unstable, ret=%i\n", ret);
+ return ret;
+ }
+
+ ret = regmap_read_poll_timeout(ctx->regmap, 0x8720, pval, pval & 0x80,
+ 10000, 1000000);
+ if (ret) {
+ dev_err(ctx->dev, "TX PLL unstable, ret=%i\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static void lt9211_atomic_enable(struct drm_bridge *bridge,
+ struct drm_bridge_state *old_bridge_state)
+{
+ struct lt9211 *ctx = bridge_to_lt9211(bridge);
+ struct drm_atomic_state *state = old_bridge_state->base.state;
+ const struct drm_bridge_state *bridge_state;
+ const struct drm_crtc_state *crtc_state;
+ const struct drm_display_mode *mode;
+ struct drm_connector *connector;
+ struct drm_crtc *crtc;
+ bool lvds_format_24bpp;
+ bool lvds_format_jeida;
+ u32 bus_flags;
+ int ret;
+
+ ret = regulator_enable(ctx->vccio);
+ if (ret) {
+ dev_err(ctx->dev, "Failed to enable vccio: %d\n", ret);
+ return;
+ }
+
+ /* Deassert reset */
+ gpiod_set_value(ctx->reset_gpio, 1);
+ usleep_range(20000, 21000); /* Very long post-reset delay. */
+
+ /* Get the LVDS format from the bridge state. */
+ bridge_state = drm_atomic_get_new_bridge_state(state, bridge);
+ bus_flags = bridge_state->output_bus_cfg.flags;
+
+ switch (bridge_state->output_bus_cfg.format) {
+ case MEDIA_BUS_FMT_RGB666_1X7X3_SPWG:
+ lvds_format_24bpp = false;
+ lvds_format_jeida = true;
+ break;
+ case MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA:
+ lvds_format_24bpp = true;
+ lvds_format_jeida = true;
+ break;
+ case MEDIA_BUS_FMT_RGB888_1X7X4_SPWG:
+ lvds_format_24bpp = true;
+ lvds_format_jeida = false;
+ break;
+ default:
+ /*
+ * Some bridges still don't set the correct
+ * LVDS bus pixel format, use SPWG24 default
+ * format until those are fixed.
+ */
+ lvds_format_24bpp = true;
+ lvds_format_jeida = false;
+ dev_warn(ctx->dev,
+ "Unsupported LVDS bus format 0x%04x, please check output bridge driver. Falling back to SPWG24.\n",
+ bridge_state->output_bus_cfg.format);
+ break;
+ }
+
+ /*
+ * Retrieve the CRTC adjusted mode. This requires a little dance to go
+ * from the bridge to the encoder, to the connector and to the CRTC.
+ */
+ connector = drm_atomic_get_new_connector_for_encoder(state,
+ bridge->encoder);
+ crtc = drm_atomic_get_new_connector_state(state, connector)->crtc;
+ crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
+ mode = &crtc_state->adjusted_mode;
+
+ ret = lt9211_read_chipid(ctx);
+ if (ret)
+ return;
+
+ ret = lt9211_system_init(ctx);
+ if (ret)
+ return;
+
+ ret = lt9211_configure_rx(ctx);
+ if (ret)
+ return;
+
+ ret = lt9211_autodetect_rx(ctx, mode);
+ if (ret)
+ return;
+
+ ret = lt9211_configure_timing(ctx, mode);
+ if (ret)
+ return;
+
+ ret = lt9211_configure_plls(ctx, mode);
+ if (ret)
+ return;
+
+ ret = lt9211_configure_tx(ctx, lvds_format_jeida, lvds_format_24bpp,
+ bus_flags & DRM_BUS_FLAG_DE_HIGH);
+ if (ret)
+ return;
+
+ dev_dbg(ctx->dev, "LT9211 enabled.\n");
+}
+
+static void lt9211_atomic_disable(struct drm_bridge *bridge,
+ struct drm_bridge_state *old_bridge_state)
+{
+ struct lt9211 *ctx = bridge_to_lt9211(bridge);
+ int ret;
+
+ /*
+ * Put the chip in reset, pull nRST line low,
+ * and assure lengthy 10ms reset low timing.
+ */
+ gpiod_set_value(ctx->reset_gpio, 0);
+ usleep_range(10000, 11000); /* Very long reset duration. */
+
+ ret = regulator_disable(ctx->vccio);
+ if (ret)
+ dev_err(ctx->dev, "Failed to disable vccio: %d\n", ret);
+
+ regcache_mark_dirty(ctx->regmap);
+}
+
+static enum drm_mode_status
+lt9211_mode_valid(struct drm_bridge *bridge,
+ const struct drm_display_info *info,
+ const struct drm_display_mode *mode)
+{
+ /* LVDS output clock range 25..176 MHz */
+ if (mode->clock < 25000)
+ return MODE_CLOCK_LOW;
+ if (mode->clock > 176000)
+ return MODE_CLOCK_HIGH;
+
+ return MODE_OK;
+}
+
+#define MAX_INPUT_SEL_FORMATS 1
+
+static u32 *
+lt9211_atomic_get_input_bus_fmts(struct drm_bridge *bridge,
+ struct drm_bridge_state *bridge_state,
+ struct drm_crtc_state *crtc_state,
+ struct drm_connector_state *conn_state,
+ u32 output_fmt,
+ unsigned int *num_input_fmts)
+{
+ u32 *input_fmts;
+
+ *num_input_fmts = 0;
+
+ input_fmts = kcalloc(MAX_INPUT_SEL_FORMATS, sizeof(*input_fmts),
+ GFP_KERNEL);
+ if (!input_fmts)
+ return NULL;
+
+ /* This is the DSI-end bus format */
+ input_fmts[0] = MEDIA_BUS_FMT_RGB888_1X24;
+ *num_input_fmts = 1;
+
+ return input_fmts;
+}
+
+static const struct drm_bridge_funcs lt9211_funcs = {
+ .attach = lt9211_attach,
+ .mode_valid = lt9211_mode_valid,
+ .atomic_enable = lt9211_atomic_enable,
+ .atomic_disable = lt9211_atomic_disable,
+ .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+ .atomic_get_input_bus_fmts = lt9211_atomic_get_input_bus_fmts,
+ .atomic_reset = drm_atomic_helper_bridge_reset,
+};
+
+static int lt9211_parse_dt(struct lt9211 *ctx)
+{
+ struct device_node *port2, *port3;
+ struct drm_bridge *panel_bridge;
+ struct device *dev = ctx->dev;
+ struct drm_panel *panel;
+ int dual_link;
+ int ret;
+
+ ctx->vccio = devm_regulator_get(dev, "vccio");
+ if (IS_ERR(ctx->vccio))
+ return dev_err_probe(dev, PTR_ERR(ctx->vccio),
+ "Failed to get supply 'vccio'\n");
+
+ ctx->lvds_dual_link = false;
+ ctx->lvds_dual_link_even_odd_swap = false;
+
+ port2 = of_graph_get_port_by_id(dev->of_node, 2);
+ port3 = of_graph_get_port_by_id(dev->of_node, 3);
+ dual_link = drm_of_lvds_get_dual_link_pixel_order(port2, port3);
+ of_node_put(port2);
+ of_node_put(port3);
+
+ if (dual_link == DRM_LVDS_DUAL_LINK_ODD_EVEN_PIXELS) {
+ ctx->lvds_dual_link = true;
+ /* Odd pixels to LVDS Channel A, even pixels to B */
+ ctx->lvds_dual_link_even_odd_swap = false;
+ } else if (dual_link == DRM_LVDS_DUAL_LINK_EVEN_ODD_PIXELS) {
+ ctx->lvds_dual_link = true;
+ /* Even pixels to LVDS Channel A, odd pixels to B */
+ ctx->lvds_dual_link_even_odd_swap = true;
+ }
+
+ ret = drm_of_find_panel_or_bridge(dev->of_node, 2, 0, &panel, &panel_bridge);
+ if (ret < 0)
+ return ret;
+ if (panel) {
+ panel_bridge = devm_drm_panel_bridge_add(dev, panel);
+ if (IS_ERR(panel_bridge))
+ return PTR_ERR(panel_bridge);
+ }
+
+ ctx->panel_bridge = panel_bridge;
+
+ return 0;
+}
+
+static int lt9211_host_attach(struct lt9211 *ctx)
+{
+ const struct mipi_dsi_device_info info = {
+ .type = "lt9211",
+ .channel = 0,
+ .node = NULL,
+ };
+ struct device *dev = ctx->dev;
+ struct device_node *host_node;
+ struct device_node *endpoint;
+ struct mipi_dsi_device *dsi;
+ struct mipi_dsi_host *host;
+ int dsi_lanes;
+ int ret;
+
+ endpoint = of_graph_get_endpoint_by_regs(dev->of_node, 0, -1);
+ dsi_lanes = of_property_count_u32_elems(endpoint, "data-lanes");
+ host_node = of_graph_get_remote_port_parent(endpoint);
+ host = of_find_mipi_dsi_host_by_node(host_node);
+ of_node_put(host_node);
+ of_node_put(endpoint);
+
+ if (!host)
+ return -EPROBE_DEFER;
+
+ if (dsi_lanes < 0 || dsi_lanes > 4)
+ return -EINVAL;
+
+ dsi = devm_mipi_dsi_device_register_full(dev, host, &info);
+ if (IS_ERR(dsi))
+ return dev_err_probe(dev, PTR_ERR(dsi),
+ "failed to create dsi device\n");
+
+ ctx->dsi = dsi;
+
+ dsi->lanes = dsi_lanes;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
+ MIPI_DSI_MODE_VIDEO_HSE;
+
+ ret = devm_mipi_dsi_attach(dev, dsi);
+ if (ret < 0) {
+ dev_err(dev, "failed to attach dsi to host: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int lt9211_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct lt9211 *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ ctx->dev = dev;
+
+ /*
+ * Put the chip in reset, pull nRST line low,
+ * and assure lengthy 10ms reset low timing.
+ */
+ ctx->reset_gpio = devm_gpiod_get_optional(ctx->dev, "reset",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(ctx->reset_gpio))
+ return PTR_ERR(ctx->reset_gpio);
+
+ usleep_range(10000, 11000); /* Very long reset duration. */
+
+ ret = lt9211_parse_dt(ctx);
+ if (ret)
+ return ret;
+
+ ctx->regmap = devm_regmap_init_i2c(client, <9211_regmap_config);
+ if (IS_ERR(ctx->regmap))
+ return PTR_ERR(ctx->regmap);
+
+ dev_set_drvdata(dev, ctx);
+ i2c_set_clientdata(client, ctx);
+
+ ctx->bridge.funcs = <9211_funcs;
+ ctx->bridge.of_node = dev->of_node;
+ drm_bridge_add(&ctx->bridge);
+
+ ret = lt9211_host_attach(ctx);
+ if (ret)
+ drm_bridge_remove(&ctx->bridge);
+
+ return ret;
+}
+
+static int lt9211_remove(struct i2c_client *client)
+{
+ struct lt9211 *ctx = i2c_get_clientdata(client);
+
+ drm_bridge_remove(&ctx->bridge);
+
+ return 0;
+}
+
+static struct i2c_device_id lt9211_id[] = {
+ { "lontium,lt9211" },
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, lt9211_id);
+
+static const struct of_device_id lt9211_match_table[] = {
+ { .compatible = "lontium,lt9211" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, lt9211_match_table);
+
+static struct i2c_driver lt9211_driver = {
+ .probe = lt9211_probe,
+ .remove = lt9211_remove,
+ .id_table = lt9211_id,
+ .driver = {
+ .name = "lt9211",
+ .of_match_table = lt9211_match_table,
+ },
+};
+module_i2c_driver(lt9211_driver);
+
+MODULE_AUTHOR("Marek Vasut <marex@denx.de>");
+MODULE_DESCRIPTION("Lontium LT9211 DSI/LVDS/DPI bridge driver");
+MODULE_LICENSE("GPL");