| Message ID | 20220523023801.410050-1-net147@gmail.com (mailing list archive) |
|---|---|
| State | Superseded, archived |
| Headers | show |
| Series | drm: bridge: icn6211: Adjust clock phase using SYS_CTRL_1 | expand |
On 5/23/22 04:38, Jonathan Liu wrote: > The code from [1] sets SYS_CTRL_1 to different values depending on the > desired clock phase (0, 1/4, 1/2 or 3/4). A clock phase of 0 aligns the > positive edge of the clock with the pixel data while other values delay > the clock by a fraction of the clock period. A clock phase of 1/2 aligns > the negative edge of the clock with the pixel data. > > The driver currently hard codes SYS_CTRL_1 to 0x88 which corresponds to > aligning the positive edge of the clock with the pixel data. This won't > work correctly for panels that require aligning the negative edge of the > clock with the pixel data. > > Adjust the clock phase to 0 if DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE is > present in bus_flags, otherwise adjust the clock phase to 1/2 as > appropriate for DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE. > > [1] https://github.com/tdjastrzebski/ICN6211-Configurator > > Signed-off-by: Jonathan Liu <net147@gmail.com> > --- > drivers/gpu/drm/bridge/chipone-icn6211.c | 10 +++++++++- > 1 file changed, 9 insertions(+), 1 deletion(-) > > diff --git a/drivers/gpu/drm/bridge/chipone-icn6211.c b/drivers/gpu/drm/bridge/chipone-icn6211.c > index 47dea657a752..df0290059aa3 100644 > --- a/drivers/gpu/drm/bridge/chipone-icn6211.c > +++ b/drivers/gpu/drm/bridge/chipone-icn6211.c > @@ -57,6 +57,10 @@ > #define BIST_CHESS_XY_H 0x30 > #define BIST_FRAME_TIME_L 0x31 > #define BIST_FRAME_TIME_H 0x32 > +#define CLK_PHASE_0 0x88 > +#define CLK_PHASE_1_4 0x98 > +#define CLK_PHASE_1_2 0xa8 > +#define CLK_PHASE_3_4 0xb8 > #define FIFO_MAX_ADDR_LOW 0x33 > #define SYNC_EVENT_DLY 0x34 > #define HSW_MIN 0x35 > @@ -414,7 +418,11 @@ static void chipone_atomic_enable(struct drm_bridge *bridge, > chipone_configure_pll(icn, mode); > > chipone_writeb(icn, SYS_CTRL(0), 0x40); > - chipone_writeb(icn, SYS_CTRL(1), 0x88); > + > + if (bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE) > + chipone_writeb(icn, SYS_CTRL(1), CLK_PHASE_0); > + else > + chipone_writeb(icn, SYS_CTRL(1), CLK_PHASE_1_2); Shouldn't both be "chipone_writeb(icn, SYS_CTRL(1), CLK_PHASE_0 | 0x8); and chipone_writeb(icn, SYS_CTRL(1), CLK_PHASE_1_2 | 0x8); respectively ? I recall you mentioned that only the top two bits indicate the clock polarity , so the bottom 6 bits are something else ? With that fixed: Reviewed-by: Marek Vasut <marex@denx.de> Thanks
diff --git a/drivers/gpu/drm/bridge/chipone-icn6211.c b/drivers/gpu/drm/bridge/chipone-icn6211.c index 47dea657a752..df0290059aa3 100644 --- a/drivers/gpu/drm/bridge/chipone-icn6211.c +++ b/drivers/gpu/drm/bridge/chipone-icn6211.c @@ -57,6 +57,10 @@ #define BIST_CHESS_XY_H 0x30 #define BIST_FRAME_TIME_L 0x31 #define BIST_FRAME_TIME_H 0x32 +#define CLK_PHASE_0 0x88 +#define CLK_PHASE_1_4 0x98 +#define CLK_PHASE_1_2 0xa8 +#define CLK_PHASE_3_4 0xb8 #define FIFO_MAX_ADDR_LOW 0x33 #define SYNC_EVENT_DLY 0x34 #define HSW_MIN 0x35 @@ -414,7 +418,11 @@ static void chipone_atomic_enable(struct drm_bridge *bridge, chipone_configure_pll(icn, mode); chipone_writeb(icn, SYS_CTRL(0), 0x40); - chipone_writeb(icn, SYS_CTRL(1), 0x88); + + if (bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE) + chipone_writeb(icn, SYS_CTRL(1), CLK_PHASE_0); + else + chipone_writeb(icn, SYS_CTRL(1), CLK_PHASE_1_2); /* icn6211 specific sequence */ chipone_writeb(icn, MIPI_FORCE_0, 0x20);
The code from [1] sets SYS_CTRL_1 to different values depending on the desired clock phase (0, 1/4, 1/2 or 3/4). A clock phase of 0 aligns the positive edge of the clock with the pixel data while other values delay the clock by a fraction of the clock period. A clock phase of 1/2 aligns the negative edge of the clock with the pixel data. The driver currently hard codes SYS_CTRL_1 to 0x88 which corresponds to aligning the positive edge of the clock with the pixel data. This won't work correctly for panels that require aligning the negative edge of the clock with the pixel data. Adjust the clock phase to 0 if DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE is present in bus_flags, otherwise adjust the clock phase to 1/2 as appropriate for DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE. [1] https://github.com/tdjastrzebski/ICN6211-Configurator Signed-off-by: Jonathan Liu <net147@gmail.com> --- drivers/gpu/drm/bridge/chipone-icn6211.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-)