diff mbox series

[v6,2/3] drm/bridge: ti-sn65dsi86: Support DisplayPort (non-eDP) mode

Message ID 20220831082653.20449-3-tomi.valkeinen@ideasonboard.com (mailing list archive)
State New, archived
Headers show
Series drm/bridge: ti-sn65dsi86: Basic DP support | expand

Commit Message

Tomi Valkeinen Aug. 31, 2022, 8:26 a.m. UTC 
From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Despite the SN65DSI86 being an eDP bridge, on some systems its output is
routed to a DisplayPort connector. Enable DisplayPort mode when the next
component in the display pipeline is detected as a DisplayPort
connector, and disable eDP features in that case.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reworked to set bridge type based on the next bridge/connector.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
--
Changes since v1/RFC:
 - Rebased on top of "drm/bridge: ti-sn65dsi86: switch to
   devm_drm_of_get_bridge"
 - eDP/DP mode determined from the next bridge connector type.

Changes since v2:
 - Remove setting of Standard DP Scrambler Seed. (It's read-only).
 - Prevent setting DP_EDP_CONFIGURATION_SET in
   ti_sn_bridge_atomic_enable()
 - Use Doug's suggested text for disabling ASSR on DP mode.

Changes since v3:
 - Remove ASSR_CONTROL definition

Changes since v4:
 - Refactor code to configure the DP/eDP scrambler in one place.
---
 drivers/gpu/drm/bridge/ti-sn65dsi86.c | 21 ++++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)
diff mbox series

Patch

diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi86.c b/drivers/gpu/drm/bridge/ti-sn65dsi86.c
index 09d3c65fa2ba..6e053e2af229 100644
--- a/drivers/gpu/drm/bridge/ti-sn65dsi86.c
+++ b/drivers/gpu/drm/bridge/ti-sn65dsi86.c
@@ -92,6 +92,8 @@ 
 #define SN_DATARATE_CONFIG_REG			0x94
 #define  DP_DATARATE_MASK			GENMASK(7, 5)
 #define  DP_DATARATE(x)				((x) << 5)
+#define SN_TRAINING_SETTING_REG			0x95
+#define  SCRAMBLE_DISABLE			BIT(4)
 #define SN_ML_TX_MODE_REG			0x96
 #define  ML_TX_MAIN_LINK_OFF			0
 #define  ML_TX_NORMAL_MODE			BIT(0)
@@ -1070,12 +1072,23 @@  static void ti_sn_bridge_atomic_enable(struct drm_bridge *bridge,
 
 	/*
 	 * The SN65DSI86 only supports ASSR Display Authentication method and
-	 * this method is enabled by default. An eDP panel must support this
+	 * this method is enabled for eDP panels. An eDP panel must support this
 	 * authentication method. We need to enable this method in the eDP panel
 	 * at DisplayPort address 0x0010A prior to link training.
+	 *
+	 * As only ASSR is supported by SN65DSI86, for full DisplayPort displays
+	 * we need to disable the scrambler.
 	 */
-	drm_dp_dpcd_writeb(&pdata->aux, DP_EDP_CONFIGURATION_SET,
-			   DP_ALTERNATE_SCRAMBLER_RESET_ENABLE);
+	if (pdata->bridge.type == DRM_MODE_CONNECTOR_eDP) {
+		drm_dp_dpcd_writeb(&pdata->aux, DP_EDP_CONFIGURATION_SET,
+				   DP_ALTERNATE_SCRAMBLER_RESET_ENABLE);
+
+		regmap_update_bits(pdata->regmap, SN_TRAINING_SETTING_REG,
+				   SCRAMBLE_DISABLE, 0);
+	} else {
+		regmap_update_bits(pdata->regmap, SN_TRAINING_SETTING_REG,
+				   SCRAMBLE_DISABLE, SCRAMBLE_DISABLE);
+	}
 
 	bpp = ti_sn_bridge_get_bpp(connector);
 	/* Set the DP output format (18 bpp or 24 bpp) */
@@ -1241,6 +1254,8 @@  static int ti_sn_bridge_probe(struct auxiliary_device *adev,
 
 	pdata->bridge.funcs = &ti_sn_bridge_funcs;
 	pdata->bridge.of_node = np;
+	pdata->bridge.type = pdata->next_bridge->type == DRM_MODE_CONNECTOR_DisplayPort
+			   ? DRM_MODE_CONNECTOR_DisplayPort : DRM_MODE_CONNECTOR_eDP;
 
 	drm_bridge_add(&pdata->bridge);