diff mbox series

drm: add kms driver for loongson display controller

Message ID 20230201170403.167665-1-15330273260@189.cn (mailing list archive)
State New, archived
Headers show
Series drm: add kms driver for loongson display controller | expand

Commit Message

Sui Jingfeng Feb. 1, 2023, 5:04 p.m. UTC
From: suijingfeng <suijingfeng@loongson.cn>

The display controller is a PCI device and It has two display pipe.
Loongson display controllers are simple which require scanout buffers
to be physically contiguous.

For LS7A1000 bridge chip, each way has a DVO interface which provide
RGB888 signals, vertical & horizontal synchronisations, and the pixel
clock. Each CRTC is able to support 1920x1080 resolution at 60Hz, the
maximum resolution is 2048x2048 according to the hardware spec.

For the DC in LS7A2000 bridge chip, each way is connected with a
built-in HDMI encoder which support 3840x2160@30.

Signed-off-by: suijingfeng <suijingfeng@loongson.cn>
Signed-off-by: suijingfeng <15330273260@189.cn>
---
 drivers/gpu/drm/Kconfig             |   2 +
 drivers/gpu/drm/Makefile            |   1 +
 drivers/gpu/drm/lsdc/Kconfig        |  18 +
 drivers/gpu/drm/lsdc/Makefile       |  14 +
 drivers/gpu/drm/lsdc/lsdc_crtc.c    | 437 +++++++++++++++++++++
 drivers/gpu/drm/lsdc/lsdc_debugfs.c | 243 ++++++++++++
 drivers/gpu/drm/lsdc/lsdc_drv.c     | 535 ++++++++++++++++++++++++++
 drivers/gpu/drm/lsdc/lsdc_drv.h     | 274 +++++++++++++
 drivers/gpu/drm/lsdc/lsdc_i2c.c     | 187 +++++++++
 drivers/gpu/drm/lsdc/lsdc_irq.c     |  81 ++++
 drivers/gpu/drm/lsdc/lsdc_output.c  | 366 ++++++++++++++++++
 drivers/gpu/drm/lsdc/lsdc_plane.c   | 447 ++++++++++++++++++++++
 drivers/gpu/drm/lsdc/lsdc_pll.c     | 571 ++++++++++++++++++++++++++++
 drivers/gpu/drm/lsdc/lsdc_pll.h     |  78 ++++
 drivers/gpu/drm/lsdc/lsdc_regs.c    |  29 ++
 drivers/gpu/drm/lsdc/lsdc_regs.h    | 294 ++++++++++++++
 16 files changed, 3577 insertions(+)
 create mode 100644 drivers/gpu/drm/lsdc/Kconfig
 create mode 100644 drivers/gpu/drm/lsdc/Makefile
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_crtc.c
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_debugfs.c
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_drv.c
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_drv.h
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_i2c.c
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_irq.c
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_output.c
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_plane.c
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_pll.c
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_pll.h
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_regs.c
 create mode 100644 drivers/gpu/drm/lsdc/lsdc_regs.h

Comments

kernel test robot Feb. 3, 2023, 7:52 a.m. UTC | #1
Hi suijingfeng,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on drm-misc/drm-misc-next]
[also build test WARNING on linus/master v6.2-rc6]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/suijingfeng/drm-add-kms-driver-for-loongson-display-controller/20230202-011138
base:   git://anongit.freedesktop.org/drm/drm-misc drm-misc-next
patch link:    https://lore.kernel.org/r/20230201170403.167665-1-15330273260%40189.cn
patch subject: [PATCH] drm: add kms driver for loongson display controller
config: mips-allyesconfig (https://download.01.org/0day-ci/archive/20230203/202302031525.A4udCUh1-lkp@intel.com/config)
compiler: mips-linux-gcc (GCC) 12.1.0
reproduce (this is a W=1 build):
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # https://github.com/intel-lab-lkp/linux/commit/ff8d5959f6dcf4abbbdbf2951345f552dc3bea46
        git remote add linux-review https://github.com/intel-lab-lkp/linux
        git fetch --no-tags linux-review suijingfeng/drm-add-kms-driver-for-loongson-display-controller/20230202-011138
        git checkout ff8d5959f6dcf4abbbdbf2951345f552dc3bea46
        # save the config file
        mkdir build_dir && cp config build_dir/.config
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=mips olddefconfig
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=mips SHELL=/bin/bash drivers/gpu/drm/lsdc/

If you fix the issue, kindly add following tag where applicable
| Reported-by: kernel test robot <lkp@intel.com>

All warnings (new ones prefixed by >>):

>> drivers/gpu/drm/lsdc/lsdc_drv.c:227:1: warning: no previous prototype for 'lsdc_detect_chip' [-Wmissing-prototypes]
     227 | lsdc_detect_chip(struct pci_dev *pdev, const struct pci_device_id * const ent)
         | ^~~~~~~~~~~~~~~~
>> drivers/gpu/drm/lsdc/lsdc_drv.c:295:21: warning: no previous prototype for 'lsdc_create_device' [-Wmissing-prototypes]
     295 | struct lsdc_device *lsdc_create_device(struct pci_dev *pdev,
         |                     ^~~~~~~~~~~~~~~~~~
   In file included from include/linux/device.h:15,
                    from include/linux/pci.h:37,
                    from drivers/gpu/drm/lsdc/lsdc_drv.c:11:
   drivers/gpu/drm/lsdc/lsdc_drv.c: In function 'lsdc_create_device':
>> drivers/gpu/drm/lsdc/lsdc_drv.c:325:46: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
     325 |         drm_info(ddev, "reg base: 0x%llx\n", (u64)ldev->reg_base);
         |                                              ^
   include/linux/dev_printk.h:110:37: note: in definition of macro 'dev_printk_index_wrap'
     110 |                 _p_func(dev, fmt, ##__VA_ARGS__);                       \
         |                                     ^~~~~~~~~~~
   include/drm/drm_print.h:456:9: note: in expansion of macro 'dev_info'
     456 |         dev_##level##type((drm)->dev, "[drm] " fmt, ##__VA_ARGS__)
         |         ^~~~
   include/drm/drm_print.h:460:9: note: in expansion of macro '__drm_printk'
     460 |         __drm_printk((drm), info,, fmt, ##__VA_ARGS__)
         |         ^~~~~~~~~~~~
   drivers/gpu/drm/lsdc/lsdc_drv.c:325:9: note: in expansion of macro 'drm_info'
     325 |         drm_info(ddev, "reg base: 0x%llx\n", (u64)ldev->reg_base);
         |         ^~~~~~~~
   drivers/gpu/drm/lsdc/lsdc_drv.c: At top level:
   drivers/gpu/drm/lsdc/lsdc_drv.c:52:31: warning: 'dc_in_ls2k1000' defined but not used [-Wunused-const-variable=]
      52 | static const struct lsdc_desc dc_in_ls2k1000 = {
         |                               ^~~~~~~~~~~~~~
   drivers/gpu/drm/lsdc/lsdc_drv.c:34:31: warning: 'dc_in_ls2k0500' defined but not used [-Wunused-const-variable=]
      34 | static const struct lsdc_desc dc_in_ls2k0500 = {
         |                               ^~~~~~~~~~~~~~


vim +/lsdc_detect_chip +227 drivers/gpu/drm/lsdc/lsdc_drv.c

   222	
   223	/*
   224	 * lsdc_detect_chip - a function to tell different chips apart.
   225	 */
   226	const struct lsdc_desc *
 > 227	lsdc_detect_chip(struct pci_dev *pdev, const struct pci_device_id * const ent)
   228	{
   229		if (ent) {
   230			struct lsdc_desc *dc_descp;
   231	
   232			dc_descp = (struct lsdc_desc *)ent->driver_data;
   233			if (dc_descp->chip == CHIP_LS7A1000)
   234				dev_info(&pdev->dev, "LS7A1000 Found, revision: %u\n", pdev->revision);
   235			else if (dc_descp->chip == CHIP_LS7A2000)
   236				dev_info(&pdev->dev, "LS7A2000 Found, revison: %u\n", pdev->revision);
   237	
   238			return dc_descp;
   239		}
   240	
   241		dev_err(&pdev->dev, "No Known Device Found\n");
   242	
   243		return NULL;
   244	}
   245	
   246	static int lsdc_vram_init(struct lsdc_device *ldev,
   247				  const struct lsdc_desc *descp)
   248	{
   249		struct drm_device *ddev = &ldev->base;
   250		struct pci_dev *gpu;
   251		resource_size_t base, size;
   252	
   253		/* The GPU and display controller in LS7A1000/LS7A2000 are separated
   254		 * PCIE devices, they are two devices not one. The DC is a pci device,
   255		 * but it don't have a dedicate VRAM bar, the BIOS engineer choose to
   256		 * assign the VRAM to the gpu device. Sadly, after years application,
   257		 * this decision form as a convention for loongson integrate graphics.
   258		 * For LS7A1000 and LS7A2000, bar 2 of GPU device contain the VRAM,
   259		 * both the GPU and the DC can make use of the VRAM depend on how DRM
   260		 * device driver is written. Therefore, we have to do some tricks here.
   261		 */
   262		if (descp->chip == CHIP_LS7A1000)
   263			gpu = pci_get_device(PCI_VENDOR_ID_LOONGSON, 0x7A15, NULL);
   264		else if (descp->chip == CHIP_LS7A2000)
   265			gpu = pci_get_device(PCI_VENDOR_ID_LOONGSON, 0x7A25, NULL);
   266	
   267		if (!gpu) {
   268			drm_warn(ddev, "No GPU device found\n");
   269			return -ENODEV;
   270		}
   271	
   272		base = pci_resource_start(gpu, 2);
   273		size = pci_resource_len(gpu, 2);
   274	
   275		ldev->vram_base = base;
   276		ldev->vram_size = size;
   277	
   278		drm_info(ddev, "vram start: 0x%llx, size: %uMB\n",
   279			 (u64)base, (u32)(size >> 20));
   280	
   281		return 0;
   282	}
   283	
   284	static int
   285	lsdc_remove_conflicting_framebuffers(const struct drm_driver *pdriver,
   286					     resource_size_t base,
   287					     resource_size_t size)
   288	{
   289		return drm_aperture_remove_conflicting_framebuffers(base,
   290								    size,
   291								    false,
   292								    pdriver);
   293	}
   294	
 > 295	struct lsdc_device *lsdc_create_device(struct pci_dev *pdev,
   296					       const struct pci_device_id *ent,
   297					       const struct drm_driver *drv)
   298	{
   299		struct lsdc_device *ldev;
   300		struct drm_device *ddev;
   301		const struct lsdc_desc *descp;
   302		int ret;
   303	
   304		ldev = devm_drm_dev_alloc(&pdev->dev, drv, struct lsdc_device, base);
   305		if (IS_ERR(ldev))
   306			return ldev;
   307	
   308		ddev = &ldev->base;
   309	
   310		pci_set_drvdata(pdev, ddev);
   311	
   312		descp = lsdc_detect_chip(pdev, ent);
   313		if (!descp)
   314			return NULL;
   315	
   316		ldev->descp = descp;
   317	
   318		spin_lock_init(&ldev->reglock);
   319	
   320		/* BAR 0 the DC device contains registers */
   321		ldev->reg_base = pcim_iomap(pdev, 0, 0);
   322		if (!ldev->reg_base)
   323			return ERR_PTR(-EIO);
   324	
 > 325		drm_info(ddev, "reg base: 0x%llx\n", (u64)ldev->reg_base);
   326	
   327		ret = lsdc_vram_init(ldev, descp);
   328		if (ret)
   329			return ERR_PTR(ret);
   330	
   331		ret = lsdc_remove_conflicting_framebuffers(drv,
   332							   ldev->vram_base,
   333							   ldev->vram_size);
   334		if (ret) {
   335			drm_err(ddev, "remove firmware framebuffers failed: %d\n", ret);
   336			return ERR_PTR(ret);
   337		}
   338	
   339		ret = drmm_vram_helper_init(ddev, ldev->vram_base, ldev->vram_size);
   340		if (ret) {
   341			drm_err(ddev, "vram helper init failed: %d\n", ret);
   342			goto err;
   343		}
   344	
   345		ret = lsdc_mode_config_init(ddev, descp);
   346		if (ret) {
   347			drm_dbg(ddev, "%s: %d\n", __func__, ret);
   348			goto err;
   349		}
   350	
   351		ret = lsdc_modeset_init(ldev, descp);
   352		if (ret)
   353			goto err;
   354	
   355		ret = drm_vblank_init(ddev, descp->num_of_crtc);
   356		if (ret)
   357			goto err;
   358	
   359		ret = request_threaded_irq(pdev->irq,
   360					   lsdc_get_irq_handler(ldev),
   361					   lsdc_irq_thread_handler,
   362					   IRQF_ONESHOT,
   363					   dev_name(ddev->dev),
   364					   ddev);
   365		if (ret) {
   366			drm_err(ddev, "Failed to register lsdc interrupt\n");
   367			goto err;
   368		}
   369	
   370		drm_kms_helper_poll_init(ddev);
   371	
   372		return ldev;
   373	
   374	err:
   375		return ERR_PTR(ret);
   376	}
   377
diff mbox series

Patch

diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig
index 663ea8f9966d..bb256a1ae24a 100644
--- a/drivers/gpu/drm/Kconfig
+++ b/drivers/gpu/drm/Kconfig
@@ -368,6 +368,8 @@  source "drivers/gpu/drm/solomon/Kconfig"
 
 source "drivers/gpu/drm/sprd/Kconfig"
 
+source "drivers/gpu/drm/lsdc/Kconfig"
+
 config DRM_HYPERV
 	tristate "DRM Support for Hyper-V synthetic video device"
 	depends on DRM && PCI && MMU && HYPERV
diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile
index 496fa5a6147a..7fd6412ffbfa 100644
--- a/drivers/gpu/drm/Makefile
+++ b/drivers/gpu/drm/Makefile
@@ -197,3 +197,4 @@  obj-y			+= gud/
 obj-$(CONFIG_DRM_HYPERV) += hyperv/
 obj-y			+= solomon/
 obj-$(CONFIG_DRM_SPRD) += sprd/
+obj-$(CONFIG_DRM_LSDC) += lsdc/
diff --git a/drivers/gpu/drm/lsdc/Kconfig b/drivers/gpu/drm/lsdc/Kconfig
new file mode 100644
index 000000000000..56a50014df9d
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/Kconfig
@@ -0,0 +1,18 @@ 
+# SPDX-License-Identifier: GPL-2.0
+
+config DRM_LSDC
+	tristate "DRM support for loongson display controller"
+	depends on DRM && PCI && (MACH_LOONGSON64 || LOONGARCH || MIPS)
+	select OF
+	select DRM_KMS_HELPER
+	select DRM_TTM
+	select DRM_TTM_HELPER
+	select DRM_VRAM_HELPER
+	select VIDEOMODE_HELPERS
+	default m
+	help
+	  This is a KMS driver for loongson display controller in the
+	  LS7A1000/LS7A2000 bridge chip and LS2K1000/LS2K0500 SoC.
+	  If "M" is selected, the module will be called lsdc.
+
+	  If in doubt, say "Y".
diff --git a/drivers/gpu/drm/lsdc/Makefile b/drivers/gpu/drm/lsdc/Makefile
new file mode 100644
index 000000000000..d4b901ec09cf
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/Makefile
@@ -0,0 +1,14 @@ 
+# SPDX-License-Identifier: GPL-2.0
+
+lsdc-y := \
+	lsdc_drv.o \
+	lsdc_crtc.o \
+	lsdc_irq.o \
+	lsdc_plane.o \
+	lsdc_pll.o \
+	lsdc_i2c.o \
+	lsdc_output.o \
+	lsdc_regs.o \
+	lsdc_debugfs.o
+
+obj-$(CONFIG_DRM_LSDC) += lsdc.o
diff --git a/drivers/gpu/drm/lsdc/lsdc_crtc.c b/drivers/gpu/drm/lsdc/lsdc_crtc.c
new file mode 100644
index 000000000000..0737b3c3084f
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_crtc.c
@@ -0,0 +1,437 @@ 
+// SPDX-License-Identifier: GPL-2.0
+
+#include <drm/drm_vblank.h>
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+#include "lsdc_pll.h"
+
+static int lsdc_crtc_enable_vblank(struct drm_crtc *crtc)
+{
+	struct lsdc_device *ldev = to_lsdc(crtc->dev);
+	unsigned int index = drm_crtc_index(crtc);
+	u32 val;
+
+	val = lsdc_rreg32(ldev, LSDC_INT_REG);
+
+	if (index == 0)
+		val |= INT_CRTC0_VS_EN;
+	else if (index == 1)
+		val |= INT_CRTC1_VS_EN;
+
+	lsdc_wreg32(ldev, LSDC_INT_REG, val);
+
+	return 0;
+}
+
+static void lsdc_crtc_disable_vblank(struct drm_crtc *crtc)
+{
+	struct lsdc_device *ldev = to_lsdc(crtc->dev);
+	unsigned int index = drm_crtc_index(crtc);
+	u32 val;
+
+	val = lsdc_rreg32(ldev, LSDC_INT_REG);
+
+	if (index == 0)
+		val &= ~INT_CRTC0_VS_EN;
+	else if (index == 1)
+		val &= ~INT_CRTC1_VS_EN;
+
+	lsdc_wreg32(ldev, LSDC_INT_REG, val);
+}
+
+static void lsdc_crtc_reset(struct drm_crtc *crtc)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	unsigned int index = drm_crtc_index(crtc);
+	struct lsdc_crtc_state *priv_crtc_state;
+	u32 val = CFG_RESET_N | LSDC_PF_XRGB8888;
+
+	/* The crtc get soft reset if bit 20 of CRTC*_CFG_REG
+	 * is write with falling edge.
+	 *
+	 * Doing this to switch from soft reset state to working state
+	 */
+	if (index == 0)
+		lsdc_wreg32(ldev, LSDC_CRTC0_CFG_REG, val);
+	else if (index == 1)
+		lsdc_wreg32(ldev, LSDC_CRTC1_CFG_REG, val);
+
+	if (crtc->state) {
+		priv_crtc_state = to_lsdc_crtc_state(crtc->state);
+		__drm_atomic_helper_crtc_destroy_state(&priv_crtc_state->base);
+		kfree(priv_crtc_state);
+	}
+
+	priv_crtc_state = kzalloc(sizeof(*priv_crtc_state), GFP_KERNEL);
+	if (!priv_crtc_state)
+		return;
+
+	__drm_atomic_helper_crtc_reset(crtc, &priv_crtc_state->base);
+
+	drm_info(ddev, "CRTC-%u reset\n", index);
+}
+
+static void lsdc_crtc_atomic_destroy_state(struct drm_crtc *crtc,
+					   struct drm_crtc_state *state)
+{
+	struct lsdc_crtc_state *priv_crtc_state = to_lsdc_crtc_state(state);
+
+	__drm_atomic_helper_crtc_destroy_state(&priv_crtc_state->base);
+
+	kfree(priv_crtc_state);
+}
+
+static struct drm_crtc_state *
+lsdc_crtc_atomic_duplicate_state(struct drm_crtc *crtc)
+{
+	struct lsdc_crtc_state *new_priv_state;
+	struct lsdc_crtc_state *old_priv_state;
+	struct drm_device *ddev = crtc->dev;
+
+	if (drm_WARN_ON(ddev, !crtc->state))
+		return NULL;
+
+	new_priv_state = kmalloc(sizeof(*new_priv_state), GFP_KERNEL);
+	if (!new_priv_state)
+		return NULL;
+
+	__drm_atomic_helper_crtc_duplicate_state(crtc, &new_priv_state->base);
+
+	old_priv_state = to_lsdc_crtc_state(crtc->state);
+
+	memcpy(&new_priv_state->pparams, &old_priv_state->pparams,
+		sizeof(new_priv_state->pparams));
+
+	return &new_priv_state->base;
+}
+
+static u32 lsdc_get_vblank_counter(struct drm_crtc *crtc)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	const struct lsdc_desc *descp = ldev->descp;
+	struct lsdc_display_pipe *dispipe = crtc_to_display_pipe(crtc);
+	unsigned int index = dispipe->index;
+
+	/* fallback to software emulated VBLANK counter */
+	if (!descp->has_vblank_counter)
+		goto fallback;
+
+	if (index == 0)
+		return lsdc_rreg32(ldev, LSDC_CRTC0_VSYNC_COUNTER_REG);
+
+	if (index == 1)
+		return lsdc_rreg32(ldev, LSDC_CRTC1_VSYNC_COUNTER_REG);
+
+fallback:
+	return (u32)drm_crtc_vblank_count(crtc);
+}
+
+static const struct drm_crtc_funcs lsdc_crtc_funcs = {
+	.reset = lsdc_crtc_reset,
+	.destroy = drm_crtc_cleanup,
+	.set_config = drm_atomic_helper_set_config,
+	.page_flip = drm_atomic_helper_page_flip,
+	.atomic_duplicate_state = lsdc_crtc_atomic_duplicate_state,
+	.atomic_destroy_state = lsdc_crtc_atomic_destroy_state,
+	.get_vblank_counter = lsdc_get_vblank_counter,
+	.enable_vblank = lsdc_crtc_enable_vblank,
+	.disable_vblank = lsdc_crtc_disable_vblank,
+	.get_vblank_timestamp = drm_crtc_vblank_helper_get_vblank_timestamp,
+};
+
+static enum drm_mode_status
+lsdc_crtc_mode_valid(struct drm_crtc *crtc,
+		     const struct drm_display_mode *mode)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	const struct lsdc_desc *descp = ldev->descp;
+
+	if (mode->hdisplay > descp->max_width)
+		return MODE_BAD_HVALUE;
+	if (mode->vdisplay > descp->max_height)
+		return MODE_BAD_VVALUE;
+
+	if (mode->clock > descp->max_pixel_clk) {
+		drm_dbg(ddev, "mode %dx%d, pixel clock=%d is too high\n",
+			mode->hdisplay, mode->vdisplay, mode->clock);
+		return MODE_CLOCK_HIGH;
+	}
+
+	if ((mode->hdisplay * 4) % descp->pitch_align) {
+		drm_dbg(ddev, "stride is require to not %u bytes aligned\n",
+			descp->pitch_align);
+		return MODE_BAD;
+	}
+
+	return MODE_OK;
+}
+
+static int lsdc_pixpll_atomic_check(struct drm_crtc *crtc,
+				    struct drm_crtc_state *state)
+{
+	struct lsdc_display_pipe *dispipe = crtc_to_display_pipe(crtc);
+	struct lsdc_pll * const pixpll = &dispipe->pixpll;
+	const struct lsdc_pixpll_funcs *pfuncs = pixpll->funcs;
+	struct lsdc_crtc_state *priv_state = to_lsdc_crtc_state(state);
+	bool ret;
+
+	ret = pfuncs->compute(pixpll, state->mode.clock, &priv_state->pparams);
+	if (ret)
+		return 0;
+
+	drm_warn(crtc->dev, "failed find PLL parameters for %u\n", state->mode.clock);
+
+	return -EINVAL;
+}
+
+static int lsdc_crtc_helper_atomic_check(struct drm_crtc *crtc,
+					 struct drm_atomic_state *state)
+{
+	struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
+
+	if (!crtc_state->enable)
+		return 0; /* no mode checks if CRTC is being disabled */
+
+	return lsdc_pixpll_atomic_check(crtc, crtc_state);
+}
+
+static void lsdc_update_pixclk(struct lsdc_display_pipe *dispipe,
+			       struct lsdc_crtc_state *priv_state)
+{
+	struct lsdc_pll * const pixpll = &dispipe->pixpll;
+	const struct lsdc_pixpll_funcs * const clkfun = pixpll->funcs;
+
+	clkfun->update(pixpll, &priv_state->pparams);
+}
+
+static void lsdc_crtc_helper_mode_set_nofb(struct drm_crtc *crtc)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	struct drm_display_mode *mode = &crtc->state->mode;
+	struct lsdc_display_pipe *dispipe = crtc_to_display_pipe(crtc);
+	struct lsdc_crtc_state *priv_state = to_lsdc_crtc_state(crtc->state);
+	unsigned int index = dispipe->index;
+	u32 h_sync, v_sync, h_val, v_val;
+	u32 val;
+
+	/* 26:16 total pixels, 10:0 visiable pixels, in horizontal */
+	h_val = (mode->crtc_htotal << 16) | mode->crtc_hdisplay;
+
+	/* 26:16 total pixels, 10:0 visiable pixels, in vertical */
+	v_val = (mode->crtc_vtotal << 16) | mode->crtc_vdisplay;
+	/* 26:16 hsync end, 10:0 hsync start, bit 30 is hsync enable */
+	h_sync = (mode->crtc_hsync_end << 16) | mode->crtc_hsync_start | CFG_HSYNC_EN;
+	if (mode->flags & DRM_MODE_FLAG_NHSYNC)
+		h_sync |= CFG_HSYNC_INV;
+
+	/* 26:16 vsync end, 10:0 vsync start, bit 30 is vsync enable */
+	v_sync = (mode->crtc_vsync_end << 16) | mode->crtc_vsync_start | CFG_VSYNC_EN;
+	if (mode->flags & DRM_MODE_FLAG_NVSYNC)
+		v_sync |= CFG_VSYNC_INV;
+
+	if (index == 0) {
+		lsdc_wreg32(ldev, LSDC_CRTC0_HDISPLAY_REG, h_val);
+		lsdc_wreg32(ldev, LSDC_CRTC0_VDISPLAY_REG, v_val);
+		lsdc_wreg32(ldev, LSDC_CRTC0_HSYNC_REG, h_sync);
+		lsdc_wreg32(ldev, LSDC_CRTC0_VSYNC_REG, v_sync);
+
+		val = lsdc_rreg32(ldev, LSDC_CRTC0_CFG_REG);
+		val = (val & ~LSDC_DMA_STEP_MASK) | LSDC_DMA_STEP_256_BYTES;
+		lsdc_wreg32(ldev, LSDC_CRTC0_CFG_REG, val);
+	} else if (index == 1) {
+		lsdc_wreg32(ldev, LSDC_CRTC1_HDISPLAY_REG, h_val);
+		lsdc_wreg32(ldev, LSDC_CRTC1_VDISPLAY_REG, v_val);
+		lsdc_wreg32(ldev, LSDC_CRTC1_HSYNC_REG, h_sync);
+		lsdc_wreg32(ldev, LSDC_CRTC1_VSYNC_REG, v_sync);
+
+		val = lsdc_rreg32(ldev, LSDC_CRTC1_CFG_REG);
+		val = (val & ~LSDC_DMA_STEP_MASK) | LSDC_DMA_STEP_256_BYTES;
+		lsdc_wreg32(ldev, LSDC_CRTC1_CFG_REG, val);
+	}
+
+	drm_dbg(ddev, "%s modeset: %ux%u\n",
+		crtc->name, mode->hdisplay, mode->vdisplay);
+
+	lsdc_update_pixclk(dispipe, priv_state);
+}
+
+static void lsdc_enable_display(struct lsdc_device *ldev, unsigned int index)
+{
+	u32 val;
+
+	if (index == 0) {
+		val = lsdc_rreg32(ldev, LSDC_CRTC0_CFG_REG);
+		val |= CFG_OUTPUT_EN;
+		lsdc_wreg32(ldev, LSDC_CRTC0_CFG_REG, val);
+		return;
+	}
+
+	if (index == 1) {
+		val = lsdc_rreg32(ldev, LSDC_CRTC1_CFG_REG);
+		val |= CFG_OUTPUT_EN;
+		lsdc_wreg32(ldev, LSDC_CRTC1_CFG_REG, val);
+		return;
+	}
+}
+
+static void lsdc_disable_display(struct lsdc_device *ldev, unsigned int index)
+{
+	u32 val;
+
+	if (index == 0) {
+		val = lsdc_rreg32(ldev, LSDC_CRTC0_CFG_REG);
+		val &= ~CFG_OUTPUT_EN;
+		lsdc_wreg32(ldev, LSDC_CRTC0_CFG_REG, val);
+		return;
+	}
+
+	if (index == 1) {
+		val = lsdc_rreg32(ldev, LSDC_CRTC1_CFG_REG);
+		val &= ~CFG_OUTPUT_EN;
+		lsdc_wreg32(ldev, LSDC_CRTC1_CFG_REG, val);
+		return;
+	}
+}
+
+static void lsdc_crtc_helper_atomic_enable(struct drm_crtc *crtc,
+					   struct drm_atomic_state *state)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+
+	drm_crtc_vblank_on(crtc);
+
+	lsdc_enable_display(ldev, drm_crtc_index(crtc));
+
+	drm_dbg(ddev, "%s: enabled\n", crtc->name);
+}
+
+static void lsdc_crtc_helper_atomic_disable(struct drm_crtc *crtc,
+					    struct drm_atomic_state *state)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+
+	lsdc_disable_display(ldev, drm_crtc_index(crtc));
+
+	drm_crtc_wait_one_vblank(crtc);
+
+	drm_crtc_vblank_off(crtc);
+
+	drm_dbg(ddev, "%s: disabled\n", crtc->name);
+}
+
+static void lsdc_crtc_atomic_flush(struct drm_crtc *crtc,
+				   struct drm_atomic_state *state)
+{
+	spin_lock_irq(&crtc->dev->event_lock);
+	if (crtc->state->event) {
+		if (drm_crtc_vblank_get(crtc) == 0)
+			drm_crtc_arm_vblank_event(crtc, crtc->state->event);
+		else
+			drm_crtc_send_vblank_event(crtc, crtc->state->event);
+		crtc->state->event = NULL;
+	}
+	spin_unlock_irq(&crtc->dev->event_lock);
+}
+
+static bool lsdc_crtc_get_scanout_position(struct drm_crtc *crtc,
+					   bool in_vblank_irq,
+					   int *vpos,
+					   int *hpos,
+					   ktime_t *stime,
+					   ktime_t *etime,
+					   const struct drm_display_mode *mode)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	unsigned int index = drm_crtc_index(crtc);
+	int line, vsw, vbp, vactive_start, vactive_end, vfp_end;
+	u32 val = 0;
+
+	vsw = mode->crtc_vsync_end - mode->crtc_vsync_start;
+	vbp = mode->crtc_vtotal - mode->crtc_vsync_end;
+
+	/*
+	 * the line counter is 1 at the start of the VSYNC pulse and VTOTAL at
+	 * the end of VFP. Translate the porch values relative to the line
+	 * counter positions.
+	 */
+
+	vactive_start = vsw + vbp + 1;
+
+	vactive_end = vactive_start + mode->crtc_vdisplay;
+
+	/* last scan line before VSYNC */
+	vfp_end = mode->crtc_vtotal;
+
+	if (stime)
+		*stime = ktime_get();
+
+	if (index == 0)
+		val = lsdc_rreg32(ldev, LSDC_CRTC0_SCAN_POS_REG);
+	else if (index == 1)
+		val = lsdc_rreg32(ldev, LSDC_CRTC1_SCAN_POS_REG);
+
+	line = (val & 0xffff);
+
+	if (line < vactive_start)
+		line -= vactive_start;
+	else if (line > vactive_end)
+		line = line - vfp_end - vactive_start;
+	else
+		line -= vactive_start;
+
+	*vpos = line;
+	*hpos = val >> 16;
+
+	if (etime)
+		*etime = ktime_get();
+
+	return true;
+}
+
+static const struct drm_crtc_helper_funcs lsdc_crtc_helper_funcs = {
+	.mode_valid = lsdc_crtc_mode_valid,
+	.mode_set_nofb = lsdc_crtc_helper_mode_set_nofb,
+	.atomic_enable = lsdc_crtc_helper_atomic_enable,
+	.atomic_disable = lsdc_crtc_helper_atomic_disable,
+	.atomic_check = lsdc_crtc_helper_atomic_check,
+	.atomic_flush = lsdc_crtc_atomic_flush,
+	.get_scanout_position = lsdc_crtc_get_scanout_position,
+};
+
+int lsdc_crtc_init(struct drm_device *ddev,
+		   struct drm_crtc *crtc,
+		   unsigned int index,
+		   struct drm_plane *primary,
+		   struct drm_plane *cursor)
+{
+	int ret;
+
+	ret = drm_crtc_init_with_planes(ddev, crtc, primary, cursor,
+					&lsdc_crtc_funcs,
+					"CRTC-%d", index);
+
+	if (ret) {
+		drm_err(ddev, "crtc init with planes failed: %d\n", ret);
+		return ret;
+	}
+
+	drm_crtc_helper_add(crtc, &lsdc_crtc_helper_funcs);
+
+	ret = drm_mode_crtc_set_gamma_size(crtc, 256);
+	if (ret)
+		drm_warn(ddev, "set the gamma table size failed\n");
+
+	drm_crtc_enable_color_mgmt(crtc, 0, false, 256);
+
+	return 0;
+}
diff --git a/drivers/gpu/drm/lsdc/lsdc_debugfs.c b/drivers/gpu/drm/lsdc/lsdc_debugfs.c
new file mode 100644
index 000000000000..e960ee5f1721
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_debugfs.c
@@ -0,0 +1,243 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <drm/drm_debugfs.h>
+#include <drm/drm_managed.h>
+#include <drm/drm_gem_vram_helper.h>
+
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+#include "lsdc_pll.h"
+
+#ifdef CONFIG_DEBUG_FS
+static int lsdc_show_clock(struct seq_file *m, void *arg)
+{
+	struct drm_info_node *node = (struct drm_info_node *)m->private;
+	struct drm_device *ddev = node->minor->dev;
+	struct drm_crtc *crtc;
+
+	drm_for_each_crtc(crtc, ddev) {
+		struct lsdc_display_pipe *pipe;
+		struct lsdc_pll *pixpll;
+		const struct lsdc_pixpll_funcs *funcs;
+		struct lsdc_pll_parms parms;
+		unsigned int out_khz;
+		struct drm_display_mode *adj;
+
+		pipe = container_of(crtc, struct lsdc_display_pipe, crtc);
+
+		adj = &crtc->state->adjusted_mode;
+
+		pixpll = &pipe->pixpll;
+		funcs = pixpll->funcs;
+		out_khz = funcs->get_clock_rate(pixpll, &parms);
+
+		seq_printf(m, "Display pipe %u: %dx%d\n",
+			   pipe->index, adj->hdisplay, adj->vdisplay);
+
+		seq_printf(m, "Frequency actually output: %u kHz\n", out_khz);
+		seq_printf(m, "Pixel clock required: %d kHz\n", adj->clock);
+		seq_printf(m, "diff: %d kHz\n", adj->clock);
+
+		seq_printf(m, "div_ref=%u, loopc=%u, div_out=%u\n",
+			   parms.div_ref, parms.loopc, parms.div_out);
+
+		seq_printf(m, "hsync_start=%d, hsync_end=%d, htotal=%d\n",
+			   adj->hsync_start, adj->hsync_end, adj->htotal);
+		seq_printf(m, "vsync_start=%d, vsync_end=%d, vtotal=%d\n\n",
+			   adj->vsync_start, adj->vsync_end, adj->vtotal);
+	}
+
+	return 0;
+}
+
+static int lsdc_show_mm(struct seq_file *m, void *arg)
+{
+	struct drm_info_node *node = (struct drm_info_node *)m->private;
+	struct drm_device *ddev = node->minor->dev;
+	struct drm_printer p = drm_seq_file_printer(m);
+
+	drm_mm_print(&ddev->vma_offset_manager->vm_addr_space_mm, &p);
+
+	return 0;
+}
+
+#define REGDEF(reg) { __stringify_1(LSDC_##reg##_REG), LSDC_##reg##_REG }
+static const struct {
+	const char *name;
+	u32 reg_offset;
+} lsdc_regs_array[] = {
+	REGDEF(CURSOR0_CFG),
+	REGDEF(CURSOR0_ADDR_LO),
+	REGDEF(CURSOR0_ADDR_HI),
+	REGDEF(CURSOR0_POSITION),
+	REGDEF(CURSOR0_BG_COLOR),
+	REGDEF(CURSOR0_FG_COLOR),
+	REGDEF(INT),
+	REGDEF(CRTC0_CFG),
+	REGDEF(CRTC0_FB0_LO_ADDR),
+	REGDEF(CRTC0_FB0_HI_ADDR),
+	REGDEF(CRTC0_FB1_LO_ADDR),
+	REGDEF(CRTC0_FB1_HI_ADDR),
+	REGDEF(CRTC0_STRIDE),
+	REGDEF(CRTC0_FB_ORIGIN),
+	REGDEF(CRTC0_HDISPLAY),
+	REGDEF(CRTC0_HSYNC),
+	REGDEF(CRTC0_VDISPLAY),
+	REGDEF(CRTC0_VSYNC),
+	REGDEF(CRTC0_GAMMA_INDEX),
+	REGDEF(CRTC0_GAMMA_DATA),
+	REGDEF(CRTC1_CFG),
+	REGDEF(CRTC1_FB0_LO_ADDR),
+	REGDEF(CRTC1_FB0_HI_ADDR),
+	REGDEF(CRTC1_FB1_LO_ADDR),
+	REGDEF(CRTC1_FB1_HI_ADDR),
+	REGDEF(CRTC1_STRIDE),
+	REGDEF(CRTC1_FB_ORIGIN),
+	REGDEF(CRTC1_HDISPLAY),
+	REGDEF(CRTC1_HSYNC),
+	REGDEF(CRTC1_VDISPLAY),
+	REGDEF(CRTC1_VSYNC),
+	REGDEF(CRTC1_GAMMA_INDEX),
+	REGDEF(CRTC1_GAMMA_DATA),
+};
+
+static int lsdc_show_regs(struct seq_file *m, void *arg)
+{
+	struct drm_info_node *node = (struct drm_info_node *)m->private;
+	struct drm_device *ddev = node->minor->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(lsdc_regs_array); i++) {
+		u32 offset = lsdc_regs_array[i].reg_offset;
+		const char *name = lsdc_regs_array[i].name;
+
+		seq_printf(m, "%s (0x%04x): 0x%08x\n",
+			   name, offset, lsdc_rreg32(ldev, offset));
+	}
+
+	return 0;
+}
+
+static int lsdc_show_vblank_counter(struct seq_file *m, void *arg)
+{
+	struct drm_info_node *node = (struct drm_info_node *)m->private;
+	struct drm_device *ddev = node->minor->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+
+	seq_printf(m, "CRTC-0 vblank counter: %08u\n",
+		   lsdc_rreg32(ldev, LSDC_CRTC0_VSYNC_COUNTER_REG));
+
+	seq_printf(m, "CRTC-1 vblank counter: %08u\n",
+		   lsdc_rreg32(ldev, LSDC_CRTC1_VSYNC_COUNTER_REG));
+
+	return 0;
+}
+
+static int lsdc_show_scan_position(struct seq_file *m, void *arg)
+{
+	struct drm_info_node *node = (struct drm_info_node *)m->private;
+	struct drm_device *ddev = node->minor->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	u32 val0 = lsdc_rreg32(ldev, LSDC_CRTC0_SCAN_POS_REG);
+	u32 val1 = lsdc_rreg32(ldev, LSDC_CRTC1_SCAN_POS_REG);
+
+	seq_printf(m, "CRTC-0: x: %08u, y: %08u\n",
+		   val0 >> 16, val0 & 0xFFFF);
+
+	seq_printf(m, "CRTC-1: x: %08u, y: %08u\n",
+		   val1 >> 16, val1 & 0xFFFF);
+
+	return 0;
+}
+
+static int lsdc_show_fb_addr(struct seq_file *m, void *arg)
+{
+	struct drm_info_node *node = (struct drm_info_node *)m->private;
+	struct drm_device *ddev = node->minor->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	u32 lo, hi;
+
+	lo = lsdc_rreg32(ldev, LSDC_CRTC0_FB0_LO_ADDR_REG);
+	hi = lsdc_rreg32(ldev, LSDC_CRTC0_FB0_HI_ADDR_REG);
+	seq_printf(m, "CRTC-0: scantout from 0x%x:%x\n", hi, lo);
+
+	lo = lsdc_rreg32(ldev, LSDC_CRTC1_FB0_LO_ADDR_REG);
+	hi = lsdc_rreg32(ldev, LSDC_CRTC1_FB0_HI_ADDR_REG);
+	seq_printf(m, "CRTC-1: scantout from 0x%x:%x\n", hi, lo);
+
+	return 0;
+}
+
+
+static struct drm_info_list lsdc_debugfs_list[] = {
+	{ "clocks",   lsdc_show_clock, 0 },
+	{ "mm",       lsdc_show_mm, 0, NULL },
+	{ "regs",     lsdc_show_regs, 0 },
+	{ "vblanks",  lsdc_show_vblank_counter, 0, NULL },
+	{ "scan_pos", lsdc_show_scan_position, 0, NULL },
+	{ "fb_addr",  lsdc_show_fb_addr, 0, NULL },
+};
+
+static int lsdc_debugfs_regset32(struct seq_file *m, void *unused)
+{
+	struct drm_info_node *node = (struct drm_info_node *)m->private;
+	struct drm_device *ddev = node->minor->dev;
+	struct debugfs_regset32 *regset = node->info_ent->data;
+	struct drm_printer p = drm_seq_file_printer(m);
+	int idx;
+
+	if (!drm_dev_enter(ddev, &idx))
+		return -ENODEV;
+
+	drm_print_regset32(&p, regset);
+
+	drm_dev_exit(idx);
+
+	return 0;
+}
+
+static int lsdc_debugfs_add_file(struct drm_minor *minor,
+				 const char *name,
+				 int (*show)(struct seq_file*, void*),
+				 void *data)
+{
+	struct drm_device *ddev = minor->dev;
+	struct dentry *root = minor->debugfs_root;
+	struct drm_info_list *file;
+
+	file = drmm_kzalloc(ddev, sizeof(*file), GFP_KERNEL);
+	if (!file)
+		return -ENOMEM;
+
+	file->name = name;
+	file->show = show;
+	file->data = data;
+
+	drm_debugfs_create_files(file, 1, root, minor);
+
+	return 0;
+}
+
+#endif
+
+int lsdc_debugfs_add_regs(struct drm_minor *minor,
+			  const char *name,
+			  struct debugfs_reg32 *regset)
+{
+#ifdef CONFIG_DEBUG_FS
+	return lsdc_debugfs_add_file(minor, name, lsdc_debugfs_regset32, regset);
+#else
+	return 0;
+#endif
+}
+
+void lsdc_debugfs_init(struct drm_minor *minor)
+{
+#ifdef CONFIG_DEBUG_FS
+	drm_debugfs_create_files(lsdc_debugfs_list,
+				 ARRAY_SIZE(lsdc_debugfs_list),
+				 minor->debugfs_root,
+				 minor);
+#endif
+}
diff --git a/drivers/gpu/drm/lsdc/lsdc_drv.c b/drivers/gpu/drm/lsdc/lsdc_drv.c
new file mode 100644
index 000000000000..4895eb9bae8d
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_drv.c
@@ -0,0 +1,535 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * KMS driver for Loongson display controller
+ * Copyright (C) 2022 Loongson Corporation
+ *
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <drm/drm_aperture.h>
+#include <drm/drm_vblank.h>
+#include <drm/drm_fb_helper.h>
+#include <drm/drm_gem_vram_helper.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+#include <drm/drm_modeset_helper.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_probe_helper.h>
+#include <drm/drm_fbdev_generic.h>
+
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+#include "lsdc_pll.h"
+
+#define DRIVER_AUTHOR		"Sui Jingfeng <suijingfeng@loongson.cn>"
+#define DRIVER_NAME		"lsdc"
+#define DRIVER_DESC		"drm driver for loongson's display controller"
+#define DRIVER_DATE		"20220701"
+#define DRIVER_MAJOR		1
+#define DRIVER_MINOR		0
+#define DRIVER_PATCHLEVEL	0
+
+static const struct lsdc_desc dc_in_ls2k0500 = {
+	.chip = CHIP_LS2K0500,
+	.num_of_crtc = LSDC_NUM_CRTC,
+	.max_pixel_clk = 200000,
+	.max_width = 2048,
+	.max_height = 2048,
+	.num_of_hw_cursor = 1,
+	.hw_cursor_w = 32,
+	.hw_cursor_h = 32,
+	.pitch_align = 256,
+	.mc_bits = 40,
+	.has_vblank_counter = false,
+	.has_builtin_i2c = false,
+	.has_vram = false,
+	.has_hpd_reg = false,
+	.is_soc = true,
+};
+
+static const struct lsdc_desc dc_in_ls2k1000 = {
+	.chip = CHIP_LS2K1000,
+	.num_of_crtc = LSDC_NUM_CRTC,
+	.max_pixel_clk = 200000,
+	.max_width = 2048,
+	.max_height = 2048,
+	.num_of_hw_cursor = 1,
+	.hw_cursor_w = 32,
+	.hw_cursor_h = 32,
+	.pitch_align = 256,
+	.mc_bits = 40,
+	.has_vblank_counter = false,
+	.has_builtin_i2c = false,
+	.has_vram = false,
+	.has_hpd_reg = false,
+	.is_soc = true,
+};
+
+static const struct lsdc_desc dc_in_ls7a1000 = {
+	.chip = CHIP_LS7A1000,
+	.num_of_crtc = LSDC_NUM_CRTC,
+	.max_pixel_clk = 200000,
+	.max_width = 2048,
+	.max_height = 2048,
+	.num_of_hw_cursor = 1,
+	.hw_cursor_w = 32,
+	.hw_cursor_h = 32,
+	.pitch_align = 256,
+	.mc_bits = 40,
+	.has_vblank_counter = false,
+	.has_builtin_i2c = true,
+	.has_vram = true,
+	.has_hpd_reg = false,
+	.is_soc = false,
+};
+
+static const struct lsdc_desc dc_in_ls7a2000 = {
+	.chip = CHIP_LS7A2000,
+	.num_of_crtc = LSDC_NUM_CRTC,
+	.max_pixel_clk = 350000,
+	.max_width = 4096,
+	.max_height = 4096,
+	.num_of_hw_cursor = 2,
+	.hw_cursor_w = 64,
+	.hw_cursor_h = 64,
+	.pitch_align = 256,
+	.mc_bits = 40, /* support 48, but use 40 for backward compatibility */
+	.has_vblank_counter = true,
+	.has_builtin_i2c = true,
+	.has_vram = true,
+	.has_hpd_reg = true,
+	.is_soc = false,
+};
+
+static int lsdc_gem_dumb_create(struct drm_file *file,
+				struct drm_device *ddev,
+				struct drm_mode_create_dumb *args)
+{
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	const struct lsdc_desc *descp = ldev->descp;
+
+	return drm_gem_vram_fill_create_dumb(file, ddev, 0, descp->pitch_align, args);
+}
+
+DEFINE_DRM_GEM_FOPS(lsdc_gem_fops);
+
+static const struct drm_driver lsdc_drm_driver = {
+	.driver_features = DRIVER_MODESET | DRIVER_GEM | DRIVER_ATOMIC,
+	.fops = &lsdc_gem_fops,
+
+	.name = DRIVER_NAME,
+	.desc = DRIVER_DESC,
+	.date = DRIVER_DATE,
+	.major = DRIVER_MAJOR,
+	.minor = DRIVER_MINOR,
+	.patchlevel = DRIVER_PATCHLEVEL,
+
+	.debugfs_init = lsdc_debugfs_init,
+	.dumb_create = lsdc_gem_dumb_create,
+	.dumb_map_offset = drm_gem_ttm_dumb_map_offset,
+	.gem_prime_mmap  = drm_gem_prime_mmap,
+};
+
+static const struct drm_mode_config_funcs lsdc_mode_config_funcs = {
+	.fb_create = drm_gem_fb_create,
+	.output_poll_changed = drm_fb_helper_output_poll_changed,
+	.atomic_check = drm_atomic_helper_check,
+	.atomic_commit = drm_atomic_helper_commit,
+	.mode_valid = drm_vram_helper_mode_valid,
+};
+
+static int lsdc_modeset_init(struct lsdc_device *ldev,
+			     const struct lsdc_desc *descp)
+{
+	struct drm_device *ddev = &ldev->base;
+	unsigned int num_crtc = descp->num_of_crtc;
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < num_crtc; i++) {
+		ret = lsdc_create_output(ldev, i);
+		if (ret)
+			return ret;
+	}
+
+	for (i = 0; i < num_crtc; i++) {
+		struct lsdc_display_pipe * const dispipe = &ldev->dispipe[i];
+		struct lsdc_pll * const pixpll = &dispipe->pixpll;
+		struct drm_plane * const primary = &dispipe->primary;
+		struct drm_plane * const cursor = &dispipe->cursor;
+		struct drm_crtc * const crtc = &dispipe->crtc;
+
+		dispipe->index = i;
+
+		ret = lsdc_pixpll_init(pixpll, ddev, i);
+		if (ret)
+			return ret;
+
+		ret = lsdc_plane_init(ldev, primary, DRM_PLANE_TYPE_PRIMARY, i);
+		if (ret)
+			return ret;
+
+		ret = lsdc_plane_init(ldev, cursor, DRM_PLANE_TYPE_CURSOR, i);
+		if (ret)
+			return ret;
+
+		/*
+		 * Initial all of the CRTC available, in this way,
+		 * the crtc index is equal to the hardware crtc index.
+		 *
+		 * display pipe 0 = crtc0 + dvo0 + encoder0 + connector0
+		 * display pipe 1 = crtc1 + dvo1 + encoder1 + connector1
+		 */
+		ret = lsdc_crtc_init(ddev, crtc, i, primary, cursor);
+		if (ret)
+			return ret;
+
+		drm_info(ddev, "display pipe %u initialized\n", i);
+	}
+
+	drm_mode_config_reset(ddev);
+
+	return 0;
+}
+
+static int lsdc_mode_config_init(struct drm_device *ddev,
+				 const struct lsdc_desc *descp)
+{
+	int ret;
+
+	ret = drmm_mode_config_init(ddev);
+	if (ret)
+		return ret;
+
+	ddev->mode_config.funcs = &lsdc_mode_config_funcs;
+	ddev->mode_config.min_width = 1;
+	ddev->mode_config.min_height = 1;
+	ddev->mode_config.max_width = descp->max_width * LSDC_NUM_CRTC;
+	ddev->mode_config.max_height = descp->max_height * LSDC_NUM_CRTC;
+	ddev->mode_config.preferred_depth = 24;
+	ddev->mode_config.prefer_shadow = 1;
+
+	ddev->mode_config.cursor_width = descp->hw_cursor_h;
+	ddev->mode_config.cursor_height = descp->hw_cursor_h;
+
+	/* max_vblank_count is set on each CRTC */
+	ddev->max_vblank_count = 0xffffffff;
+
+	return ret;
+}
+
+/*
+ * lsdc_detect_chip - a function to tell different chips apart.
+ */
+const struct lsdc_desc *
+lsdc_detect_chip(struct pci_dev *pdev, const struct pci_device_id * const ent)
+{
+	if (ent) {
+		struct lsdc_desc *dc_descp;
+
+		dc_descp = (struct lsdc_desc *)ent->driver_data;
+		if (dc_descp->chip == CHIP_LS7A1000)
+			dev_info(&pdev->dev, "LS7A1000 Found, revision: %u\n", pdev->revision);
+		else if (dc_descp->chip == CHIP_LS7A2000)
+			dev_info(&pdev->dev, "LS7A2000 Found, revison: %u\n", pdev->revision);
+
+		return dc_descp;
+	}
+
+	dev_err(&pdev->dev, "No Known Device Found\n");
+
+	return NULL;
+}
+
+static int lsdc_vram_init(struct lsdc_device *ldev,
+			  const struct lsdc_desc *descp)
+{
+	struct drm_device *ddev = &ldev->base;
+	struct pci_dev *gpu;
+	resource_size_t base, size;
+
+	/* The GPU and display controller in LS7A1000/LS7A2000 are separated
+	 * PCIE devices, they are two devices not one. The DC is a pci device,
+	 * but it don't have a dedicate VRAM bar, the BIOS engineer choose to
+	 * assign the VRAM to the gpu device. Sadly, after years application,
+	 * this decision form as a convention for loongson integrate graphics.
+	 * For LS7A1000 and LS7A2000, bar 2 of GPU device contain the VRAM,
+	 * both the GPU and the DC can make use of the VRAM depend on how DRM
+	 * device driver is written. Therefore, we have to do some tricks here.
+	 */
+	if (descp->chip == CHIP_LS7A1000)
+		gpu = pci_get_device(PCI_VENDOR_ID_LOONGSON, 0x7A15, NULL);
+	else if (descp->chip == CHIP_LS7A2000)
+		gpu = pci_get_device(PCI_VENDOR_ID_LOONGSON, 0x7A25, NULL);
+
+	if (!gpu) {
+		drm_warn(ddev, "No GPU device found\n");
+		return -ENODEV;
+	}
+
+	base = pci_resource_start(gpu, 2);
+	size = pci_resource_len(gpu, 2);
+
+	ldev->vram_base = base;
+	ldev->vram_size = size;
+
+	drm_info(ddev, "vram start: 0x%llx, size: %uMB\n",
+		 (u64)base, (u32)(size >> 20));
+
+	return 0;
+}
+
+static int
+lsdc_remove_conflicting_framebuffers(const struct drm_driver *pdriver,
+				     resource_size_t base,
+				     resource_size_t size)
+{
+	return drm_aperture_remove_conflicting_framebuffers(base,
+							    size,
+							    false,
+							    pdriver);
+}
+
+struct lsdc_device *lsdc_create_device(struct pci_dev *pdev,
+				       const struct pci_device_id *ent,
+				       const struct drm_driver *drv)
+{
+	struct lsdc_device *ldev;
+	struct drm_device *ddev;
+	const struct lsdc_desc *descp;
+	int ret;
+
+	ldev = devm_drm_dev_alloc(&pdev->dev, drv, struct lsdc_device, base);
+	if (IS_ERR(ldev))
+		return ldev;
+
+	ddev = &ldev->base;
+
+	pci_set_drvdata(pdev, ddev);
+
+	descp = lsdc_detect_chip(pdev, ent);
+	if (!descp)
+		return NULL;
+
+	ldev->descp = descp;
+
+	spin_lock_init(&ldev->reglock);
+
+	/* BAR 0 the DC device contains registers */
+	ldev->reg_base = pcim_iomap(pdev, 0, 0);
+	if (!ldev->reg_base)
+		return ERR_PTR(-EIO);
+
+	drm_info(ddev, "reg base: 0x%llx\n", (u64)ldev->reg_base);
+
+	ret = lsdc_vram_init(ldev, descp);
+	if (ret)
+		return ERR_PTR(ret);
+
+	ret = lsdc_remove_conflicting_framebuffers(drv,
+						   ldev->vram_base,
+						   ldev->vram_size);
+	if (ret) {
+		drm_err(ddev, "remove firmware framebuffers failed: %d\n", ret);
+		return ERR_PTR(ret);
+	}
+
+	ret = drmm_vram_helper_init(ddev, ldev->vram_base, ldev->vram_size);
+	if (ret) {
+		drm_err(ddev, "vram helper init failed: %d\n", ret);
+		goto err;
+	}
+
+	ret = lsdc_mode_config_init(ddev, descp);
+	if (ret) {
+		drm_dbg(ddev, "%s: %d\n", __func__, ret);
+		goto err;
+	}
+
+	ret = lsdc_modeset_init(ldev, descp);
+	if (ret)
+		goto err;
+
+	ret = drm_vblank_init(ddev, descp->num_of_crtc);
+	if (ret)
+		goto err;
+
+	ret = request_threaded_irq(pdev->irq,
+				   lsdc_get_irq_handler(ldev),
+				   lsdc_irq_thread_handler,
+				   IRQF_ONESHOT,
+				   dev_name(ddev->dev),
+				   ddev);
+	if (ret) {
+		drm_err(ddev, "Failed to register lsdc interrupt\n");
+		goto err;
+	}
+
+	drm_kms_helper_poll_init(ddev);
+
+	return ldev;
+
+err:
+	return ERR_PTR(ret);
+}
+
+static int lsdc_pci_probe(struct pci_dev *pdev,
+			  const struct pci_device_id *ent)
+{
+	struct drm_device *ddev;
+	struct lsdc_device *ldev;
+	int ret;
+
+	ret = pcim_enable_device(pdev);
+	if (ret)
+		return ret;
+
+	pci_set_master(pdev);
+
+	ldev = lsdc_create_device(pdev, ent, &lsdc_drm_driver);
+	if (IS_ERR(ldev))
+		return PTR_ERR(ldev);
+
+	ddev = &ldev->base;
+
+	ret = drm_dev_register(ddev, 0);
+	if (ret)
+		return ret;
+
+	drm_fbdev_generic_setup(ddev, 32);
+
+	return 0;
+}
+
+static void lsdc_pci_remove(struct pci_dev *pdev)
+{
+	struct drm_device *ddev = pci_get_drvdata(pdev);
+
+	drm_dev_unregister(ddev);
+	drm_atomic_helper_shutdown(ddev);
+}
+
+static int lsdc_drm_freeze(struct drm_device *ddev)
+{
+	int error;
+
+	error = drm_mode_config_helper_suspend(ddev);
+	if (error)
+		return error;
+
+	pci_save_state(to_pci_dev(ddev->dev));
+
+	return 0;
+}
+
+static int lsdc_drm_resume(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct drm_device *ddev = pci_get_drvdata(pdev);
+
+	return drm_mode_config_helper_resume(ddev);
+}
+
+static int lsdc_pm_freeze(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct drm_device *ddev = pci_get_drvdata(pdev);
+
+	return lsdc_drm_freeze(ddev);
+}
+
+static int lsdc_pm_thaw(struct device *dev)
+{
+	return lsdc_drm_resume(dev);
+}
+
+static int lsdc_pm_suspend(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	int error;
+
+	error = lsdc_pm_freeze(dev);
+	if (error)
+		return error;
+
+	pci_save_state(pdev);
+	/* Shut down the device */
+	pci_disable_device(pdev);
+	pci_set_power_state(pdev, PCI_D3hot);
+
+	return 0;
+}
+
+static int lsdc_pm_resume(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+
+	if (pcim_enable_device(pdev))
+		return -EIO;
+
+	pci_set_power_state(pdev, PCI_D0);
+
+	pci_restore_state(pdev);
+
+	return lsdc_pm_thaw(dev);
+}
+
+static const struct dev_pm_ops lsdc_pm_ops = {
+	.suspend = lsdc_pm_suspend,
+	.resume = lsdc_pm_resume,
+	.freeze = lsdc_pm_freeze,
+	.thaw = lsdc_pm_thaw,
+	.poweroff = lsdc_pm_freeze,
+	.restore = lsdc_pm_resume,
+};
+
+static const struct pci_device_id lsdc_pciid_list[] = {
+	{PCI_VENDOR_ID_LOONGSON, 0x7a06, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+	 (unsigned long) &dc_in_ls7a1000},
+	{PCI_VENDOR_ID_LOONGSON, 0x7a36, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+	 (unsigned long) &dc_in_ls7a2000},
+	{0, 0, 0, 0, 0, 0, 0}
+};
+
+static struct pci_driver lsdc_pci_driver = {
+	.name = DRIVER_NAME,
+	.id_table = lsdc_pciid_list,
+	.probe = lsdc_pci_probe,
+	.remove = lsdc_pci_remove,
+	.driver.pm = &lsdc_pm_ops,
+};
+
+static int __init lsdc_module_init(void)
+{
+	struct pci_dev *pdev = NULL;
+
+	if (drm_firmware_drivers_only())
+		return -EINVAL;
+
+	while ((pdev = pci_get_class(PCI_CLASS_DISPLAY_VGA << 8, pdev))) {
+		/*
+		 * Multiple video card workaround: lsdc will always be
+		 * selected as the default boot device by vgaarb subsystem.
+		 */
+		if (pdev->vendor != PCI_VENDOR_ID_LOONGSON) {
+			pr_info("Discrete graphic card detected, abort\n");
+			return 0;
+		}
+	}
+
+	return pci_register_driver(&lsdc_pci_driver);
+}
+module_init(lsdc_module_init);
+
+static void __exit lsdc_module_exit(void)
+{
+	pci_unregister_driver(&lsdc_pci_driver);
+}
+module_exit(lsdc_module_exit);
+
+MODULE_DEVICE_TABLE(pci, lsdc_pciid_list);
+MODULE_AUTHOR(DRIVER_AUTHOR);
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
diff --git a/drivers/gpu/drm/lsdc/lsdc_drv.h b/drivers/gpu/drm/lsdc/lsdc_drv.h
new file mode 100644
index 000000000000..b69389ddfcd5
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_drv.h
@@ -0,0 +1,274 @@ 
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * KMS driver for Loongson display controller
+ * Copyright (C) 2022 Loongson Corporation
+ *
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#ifndef __LSDC_DRV_H__
+#define __LSDC_DRV_H__
+
+#include <linux/i2c.h>
+#include <linux/i2c-algo-bit.h>
+
+#include <drm/drm_print.h>
+#include <drm/drm_device.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_plane.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_encoder.h>
+#include <drm/drm_drv.h>
+#include <drm/drm_atomic.h>
+
+#include "lsdc_regs.h"
+#include "lsdc_pll.h"
+
+#define LSDC_NUM_CRTC           2
+
+/*
+ * The display controller in LS7A2000 integrate Loongson self-made encoder
+ * Display pipe 0 has a transparent VGA encoder and a HDMI phy, they are
+ * parallel. Display pipe 1 has only one HDMI phy.
+ *       ______________________                          _____________
+ *      |             +-----+  |                        |             |
+ *      | CRTC0 -+--> | VGA |  ----> VGA Connector ---> | VGA Monitor |<---+
+ *      |        |    +-----+  |                        |_____________|    |
+ *      |        |             |                         ______________    |
+ *      |        |    +------+ |                        |              |   |
+ *      |        +--> | HDMI | ----> HDMI Connector --> | HDMI Monitor |<--+
+ *      |             +------+ |                        |______________|   |
+ *      |            +------+  |                                           |
+ *      |            | i2c6 |  <-------------------------------------------+
+ *      |            +------+  |
+ *      |                      |
+ *      |    DC in LS7A2000    |
+ *      |                      |
+ *      |            +------+  |
+ *      |            | i2c7 |  <--------------------------------+
+ *      |            +------+  |                                |
+ *      |                      |                          ______|_______
+ *      |            +------+  |                         |              |
+ *      | CRTC1 ---> | HDMI |  ----> HDMI Connector ---> | HDMI Monitor |
+ *      |            +------+  |                         |______________|
+ *      |______________________|
+ *
+ *
+ * The display controller in LS7A1000.
+ *       ___________________                                     _________
+ *      |            -------|                                   |         |
+ *      |  CRTC0 --> | DVO0 ----> Encoder0 ---> Connector0 ---> | Display |
+ *      |  _   _     -------|        ^             ^            |_________|
+ *      | | | | |    -------|        |             |
+ *      | |_| |_|    | i2c6 <--------+-------------+
+ *      |            -------|
+ *      |  _   _     -------|
+ *      | | | | |    | i2c7 <--------+-------------+
+ *      | |_| |_|    -------|        |             |             _________
+ *      |            -------|        |             |            |         |
+ *      |  CRTC1 --> | DVO1 ----> Encoder1 ---> Connector1 ---> |  Panel  |
+ *      |            -------|                                   |_________|
+ *      |___________________|
+ *
+ *
+ * The display controller in LS2K1000.
+ *       ___________________                                     _________
+ *      |            -------|                                   |         |
+ *      |  CRTC0 --> | DVO0 ----> Encoder0 ---> Connector0 ---> | Display |
+ *      |  _   _     -------|        ^              ^           |_________|
+ *      | | | | |           |        |              |
+ *      | |_| |_|           |     +------+          |
+ *      |                   <---->| i2c0 |<---------+
+ *      |  DC in LS2K1000   |     +------+
+ *      |  _   _            |     +------+
+ *      | | | | |           <---->| i2c1 |----------+
+ *      | |_| |_|           |     +------+          |            _________
+ *      |            -------|        |              |           |         |
+ *      |  CRTC1 --> | DVO1 ----> Encoder1 ---> Connector1 ---> |  Panel  |
+ *      |            -------|                                   |_________|
+ *      |___________________|
+ *
+ *
+ * The display controller in LS2K0500, LS2K0500 has a built-in transparent
+ * VGA encoder which is connected to display pipe 1(CRTC1).
+ *       ___________________                                     _________
+ *      |            -------|                                   |         |
+ *      |  CRTC0 --> | DVO0 ----> Encoder0 ---> Connector0 ---> | Display |
+ *      |  _   _     -------|        ^              ^           |_________|
+ *      | | | | |           |        |              |
+ *      | |_| |_|           |     +------+          |
+ *      |                   <---->| i2c4 |<---------+
+ *      |  DC in LS2K0500   |     +------+
+ *      |  _   _            |     +------+
+ *      | | | | |           <---->| i2c5 |-------------------+
+ *      | |_| |_|           |     +------+             ______|______
+ *      |           +-----+ |                         |             |
+ *      | CRTC1 --> | VGA | ------------------------> | VGA Monitor |
+ *      |           +-----+ |                         |_____________|
+ *      |___________________|
+ *
+ * LS7A1000 and LS7A2000 are bridge chips, has dedicated Video RAM.
+ * while LS2K2000/LS2K1000/LS2K0500 are SoC, they don't have dediacated
+ * Video RAM.
+ *
+ * There is only a 1:1 mapping of encoders and connectors for the DC,
+ * each CRTC have two FB address registers.
+ */
+
+enum loongson_chip_family {
+	CHIP_UNKNOWN = 0,
+	CHIP_LS7A1000 = 1,  /* North bridge of LS3A3000/LS3A4000/LS3A5000 */
+	CHIP_LS7A2000 = 2,  /* Update version of LS7A1000, with builtin HDMI encoder */
+	CHIP_LS2K0500 = 3,  /* Reduced version of LS2K1000, single core */
+	CHIP_LS2K1000 = 4,  /* 2-Core Mips64r2/LA264 SoC, 64-bit, 1.0 Ghz */
+	CHIP_LS2K2000 = 5,  /* 2-Core 64-bit LA364 SoC, 1.2 ~ 1.5 Ghz */
+	CHIP_LAST,
+};
+
+struct lsdc_desc {
+	enum loongson_chip_family chip;
+	u32 num_of_crtc;
+	u32 max_pixel_clk;
+	u32 max_width;
+	u32 max_height;
+	u32 num_of_hw_cursor;
+	u32 hw_cursor_w;
+	u32 hw_cursor_h;
+	u32 pitch_align;  /* DMA alignment constraint */
+	u64 mc_bits;      /* physical address bus bit width */
+	bool has_vblank_counter;
+	bool has_builtin_i2c;
+	bool has_vram;
+	bool has_hpd_reg;
+	bool is_soc;
+};
+
+struct lsdc_i2c {
+	struct i2c_adapter adapter;
+	struct i2c_algo_bit_data bit;
+	struct drm_device *ddev;
+	void __iomem *reg_base;
+	void __iomem *dir_reg;
+	void __iomem *dat_reg;
+	int index;
+	/* pin bit mask */
+	u8 sda;
+	u8 scl;
+};
+
+/*
+ * struct lsdc_display_pipe - Abstraction of hardware display pipeline.
+ * @crtc: CRTC control structure
+ * @primary: framebuffer plane control structure
+ * @cursor: cursor plane control structure
+ * @output: output control structure of this display pipe bind
+ * @pixpll: pixel pll control structure
+ * @index: the index corresponding to the hardware display pipe
+ */
+struct lsdc_display_pipe {
+	struct drm_crtc crtc;
+	struct drm_plane primary;
+	struct drm_plane cursor;
+	struct drm_encoder encoder;
+	struct drm_connector connector;
+	struct lsdc_pll pixpll;
+	struct lsdc_i2c *li2c;
+	int index;
+};
+
+static inline struct lsdc_display_pipe *
+crtc_to_display_pipe(struct drm_crtc *crtc)
+{
+	return container_of(crtc, struct lsdc_display_pipe, crtc);
+}
+
+static inline struct lsdc_display_pipe *
+cursor_to_display_pipe(struct drm_plane *cursor)
+{
+	return container_of(cursor, struct lsdc_display_pipe, cursor);
+}
+
+static inline struct lsdc_display_pipe *
+connector_to_display_pipe(struct drm_connector *conn)
+{
+	return container_of(conn, struct lsdc_display_pipe, connector);
+}
+
+static inline struct lsdc_display_pipe *
+encoder_to_display_pipe(struct drm_encoder *enc)
+{
+	return container_of(enc, struct lsdc_display_pipe, encoder);
+}
+
+struct lsdc_crtc_state {
+	struct drm_crtc_state base;
+	struct lsdc_pll_parms pparams;
+};
+
+struct lsdc_device {
+	struct drm_device base;
+
+	/* @reglock: protects concurrent register access */
+	spinlock_t reglock;
+	void __iomem *reg_base;
+	void __iomem *vram;
+	resource_size_t vram_base;
+	resource_size_t vram_size;
+	u64 mc_mask;
+
+	struct lsdc_display_pipe dispipe[LSDC_NUM_CRTC];
+
+	/* @num_output: count the number of active display pipe */
+	unsigned int num_output;
+
+	/* @descp: feature descriptions of the DC variant */
+	const struct lsdc_desc *descp;
+
+	u32 irq_status;
+};
+
+static inline struct lsdc_device *
+to_lsdc(struct drm_device *ddev)
+{
+	return container_of(ddev, struct lsdc_device, base);
+}
+
+static inline struct lsdc_crtc_state *
+to_lsdc_crtc_state(struct drm_crtc_state *base)
+{
+	return container_of(base, struct lsdc_crtc_state, base);
+}
+
+int lsdc_crtc_init(struct drm_device *ddev,
+		   struct drm_crtc *crtc,
+		   unsigned int index,
+		   struct drm_plane *primary,
+		   struct drm_plane *cursor);
+
+int lsdc_plane_init(struct lsdc_device *ldev,
+		    struct drm_plane *plane,
+		    enum drm_plane_type type,
+		    unsigned int index);
+
+int lsdc_create_output(struct lsdc_device *ldev, unsigned int index);
+
+struct lsdc_i2c *lsdc_create_i2c_chan(struct drm_device *ddev,
+				      void *base,
+				      unsigned int index);
+
+struct i2c_adapter *lsdc_get_i2c_adapter(struct lsdc_device *ldev,
+					 unsigned int index);
+
+irqreturn_t lsdc_irq_thread_handler(int irq, void *arg);
+irq_handler_t lsdc_get_irq_handler(struct lsdc_device *ldev);
+
+u32 lsdc_rreg32(struct lsdc_device * const ldev, u32 offset);
+void lsdc_wreg32(struct lsdc_device * const ldev, u32 offset, u32 val);
+
+void lsdc_debugfs_init(struct drm_minor *minor);
+int lsdc_debugfs_add_regs(struct drm_minor *minor,
+			  const char *name,
+			  struct debugfs_reg32 *regset);
+
+#endif
diff --git a/drivers/gpu/drm/lsdc/lsdc_i2c.c b/drivers/gpu/drm/lsdc/lsdc_i2c.c
new file mode 100644
index 000000000000..19e4918670dd
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_i2c.c
@@ -0,0 +1,187 @@ 
+// SPDX-License-Identifier: GPL-2.0
+
+#include <linux/i2c.h>
+#include <linux/pci.h>
+#include <drm/drm_managed.h>
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+
+/*
+ * ls7a_gpio_i2c_set - set the state of a gpio pin indicated by mask
+ * @mask: gpio pin mask
+ */
+static void ls7a_gpio_i2c_set(struct lsdc_i2c * const li2c, int mask, int state)
+{
+	struct lsdc_device *ldev = to_lsdc(li2c->ddev);
+	unsigned long flags;
+	u8 val;
+
+	spin_lock_irqsave(&ldev->reglock, flags);
+
+	if (state) {
+		/* Setting this pin as input directly, write 1 for Input.
+		 * The external pull-up resistor will pull the level up
+		 */
+		val = readb(li2c->dir_reg);
+		val |= mask;
+		writeb(val, li2c->dir_reg);
+	} else {
+		/* First set this pin as output, write 0 for Output */
+		val = readb(li2c->dir_reg);
+		val &= ~mask;
+		writeb(val, li2c->dir_reg);
+
+		/* Then, make this pin output 0 */
+		val = readb(li2c->dat_reg);
+		val &= ~mask;
+		writeb(val, li2c->dat_reg);
+	}
+
+	spin_unlock_irqrestore(&ldev->reglock, flags);
+}
+
+/*
+ * ls7a_gpio_i2c_get - read value back from gpio pin
+ * @mask: gpio pin mask
+ */
+static int ls7a_gpio_i2c_get(struct lsdc_i2c * const li2c, int mask)
+{
+	struct lsdc_device *ldev = to_lsdc(li2c->ddev);
+	unsigned long flags;
+	u8 val;
+
+	spin_lock_irqsave(&ldev->reglock, flags);
+
+	/* First set this pin as input */
+	val = readb(li2c->dir_reg);
+	val |= mask;
+	writeb(val, li2c->dir_reg);
+
+	/* Then get level state from this pin */
+	val = readb(li2c->dat_reg);
+
+	spin_unlock_irqrestore(&ldev->reglock, flags);
+
+	return (val & mask) ? 1 : 0;
+}
+
+static void ls7a_i2c_set_sda(void *i2c, int state)
+{
+	struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
+	/* set state on the li2c->sda pin */
+	return ls7a_gpio_i2c_set(li2c, li2c->sda, state);
+}
+
+static void ls7a_i2c_set_scl(void *i2c, int state)
+{
+	struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
+	/* set state on the li2c->scl pin */
+	return ls7a_gpio_i2c_set(li2c, li2c->scl, state);
+}
+
+static int ls7a_i2c_get_sda(void *i2c)
+{
+	struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
+	/* read value from the li2c->sda pin */
+	return ls7a_gpio_i2c_get(li2c, li2c->sda);
+}
+
+static int ls7a_i2c_get_scl(void *i2c)
+{
+	struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
+	/* read the value from the li2c->scl pin */
+	return ls7a_gpio_i2c_get(li2c, li2c->scl);
+}
+
+static void lsdc_destroy_i2c(struct drm_device *ddev, void *data)
+{
+	struct lsdc_i2c *li2c = (struct lsdc_i2c *)data;
+
+	if (li2c) {
+		i2c_del_adapter(&li2c->adapter);
+		kfree(li2c);
+	}
+}
+
+/*
+ * The DC in ls7a1000/ls7a2000 have builtin gpio hardware
+ *
+ * @base : gpio reg base
+ * @index : output channel index, 0 for DVO0, 1 for DVO1
+ */
+struct lsdc_i2c *lsdc_create_i2c_chan(struct drm_device *ddev,
+				      void *base,
+				      unsigned int index)
+{
+	struct i2c_adapter *adapter;
+	struct lsdc_i2c *li2c;
+	int ret;
+
+	li2c = devm_kzalloc(ddev->dev, sizeof(*li2c), GFP_KERNEL);
+	if (!li2c)
+		return ERR_PTR(-ENOMEM);
+
+	if (index == 0) {
+		li2c->sda = 0x01;  /* pin 0 */
+		li2c->scl = 0x02;  /* pin 1 */
+	} else if (index == 1) {
+		li2c->sda = 0x04;  /* pin 2 */
+		li2c->scl = 0x08;  /* pin 3 */
+	}
+
+	li2c->index = index;
+	li2c->reg_base = base;
+	li2c->ddev = ddev;
+	li2c->dir_reg = li2c->reg_base + LS7A_DC_GPIO_DIR_REG;
+	li2c->dat_reg = li2c->reg_base + LS7A_DC_GPIO_DAT_REG;
+
+	li2c->bit.setsda = ls7a_i2c_set_sda;
+	li2c->bit.setscl = ls7a_i2c_set_scl;
+	li2c->bit.getsda = ls7a_i2c_get_sda;
+	li2c->bit.getscl = ls7a_i2c_get_scl;
+	li2c->bit.udelay = 5;
+	li2c->bit.timeout = usecs_to_jiffies(2200);
+	li2c->bit.data = li2c;
+
+	adapter = &li2c->adapter;
+	adapter->algo_data = &li2c->bit;
+	adapter->owner = THIS_MODULE;
+	adapter->class = I2C_CLASS_DDC;
+	adapter->dev.parent = ddev->dev;
+	adapter->nr = -1;
+
+	snprintf(adapter->name, sizeof(adapter->name), "lsdc-i2c%u", index);
+
+	i2c_set_adapdata(adapter, li2c);
+
+	ret = i2c_bit_add_bus(adapter);
+	if (ret) {
+		devm_kfree(ddev->dev, li2c);
+		return ERR_PTR(ret);
+	}
+
+	ret = drmm_add_action_or_reset(ddev, lsdc_destroy_i2c, li2c);
+	if (ret)
+		return NULL;
+
+	drm_info(ddev, "%s(sda=%u, scl=%u) created for connector-%u\n",
+		 adapter->name, li2c->sda, li2c->scl, index);
+
+	return li2c;
+}
+
+struct i2c_adapter *lsdc_get_i2c_adapter(struct lsdc_device *ldev,
+					 unsigned int index)
+{
+	const struct lsdc_desc *descp = ldev->descp;
+	struct lsdc_display_pipe *dispipe = &ldev->dispipe[index];
+
+	if (descp->has_builtin_i2c) {
+		struct lsdc_i2c *li2c = dispipe->li2c;
+
+		if (li2c)
+			return &li2c->adapter;
+	}
+
+	return NULL;
+}
diff --git a/drivers/gpu/drm/lsdc/lsdc_irq.c b/drivers/gpu/drm/lsdc/lsdc_irq.c
new file mode 100644
index 000000000000..2c9ab60ceb4d
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_irq.c
@@ -0,0 +1,81 @@ 
+// SPDX-License-Identifier: GPL-2.0
+
+#include <drm/drm_vblank.h>
+
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+
+/* For the DC in ls7a2000 */
+static irqreturn_t lsdc_irq_handler(int irq, void *arg)
+{
+	struct drm_device *ddev = arg;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	u32 val;
+
+	/* Read the interrupt status */
+	val = lsdc_rreg32(ldev, LSDC_INT_REG);
+	if ((val & INT_STATUS_MASK) == 0) {
+		drm_warn(ddev, "no interrupt occurs\n");
+		return IRQ_NONE;
+	}
+
+	ldev->irq_status = val;
+
+	/* write "1" to clear the interrupt status */
+	lsdc_wreg32(ldev, LSDC_INT_REG, val);
+
+	return IRQ_WAKE_THREAD;
+}
+
+/* For the DC in ls7a1000, ls2k1000 and ls2k0500,  */
+static irqreturn_t lsdc_irq_handler_legacy(int irq, void *arg)
+{
+	struct drm_device *ddev = arg;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	u32 val;
+
+	/* Read the interrupt status */
+	val = lsdc_rreg32(ldev, LSDC_INT_REG);
+	if ((val & INT_STATUS_MASK) == 0) {
+		drm_warn(ddev, "no interrupt occurs\n");
+		return IRQ_NONE;
+	}
+
+	ldev->irq_status = val;
+
+	val &= ~INT_STATUS_MASK;
+
+	/* write "0" to clear the interrupt status */
+	lsdc_wreg32(ldev, LSDC_INT_REG, val);
+
+	return IRQ_WAKE_THREAD;
+}
+
+irq_handler_t lsdc_get_irq_handler(struct lsdc_device *ldev)
+{
+	const struct lsdc_desc *descp = ldev->descp;
+
+	if (descp->chip == CHIP_LS7A2000)
+		return lsdc_irq_handler;
+
+	return lsdc_irq_handler_legacy;
+}
+
+irqreturn_t lsdc_irq_thread_handler(int irq, void *arg)
+{
+	struct drm_device *ddev = arg;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	struct drm_crtc *crtc;
+
+	if (ldev->irq_status & INT_CRTC0_VSYNC) {
+		crtc = drm_crtc_from_index(ddev, 0);
+		drm_crtc_handle_vblank(crtc);
+	}
+
+	if (ldev->irq_status & INT_CRTC1_VSYNC) {
+		crtc = drm_crtc_from_index(ddev, 1);
+		drm_crtc_handle_vblank(crtc);
+	}
+
+	return IRQ_HANDLED;
+}
diff --git a/drivers/gpu/drm/lsdc/lsdc_output.c b/drivers/gpu/drm/lsdc/lsdc_output.c
new file mode 100644
index 000000000000..6ce0eba7a1c3
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_output.c
@@ -0,0 +1,366 @@ 
+// SPDX-License-Identifier: GPL-2.0
+
+#include <drm/drm_edid.h>
+#include <drm/drm_probe_helper.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_connector.h>
+#include "lsdc_drv.h"
+
+static int lsdc_get_modes(struct drm_connector *connector)
+{
+	unsigned int num = 0;
+	struct edid *edid;
+
+	if (connector->ddc) {
+		edid = drm_get_edid(connector, connector->ddc);
+		if (edid) {
+			drm_connector_update_edid_property(connector, edid);
+			num = drm_add_edid_modes(connector, edid);
+			kfree(edid);
+		}
+
+		return num;
+	}
+
+	/*
+	 * In case we cannot retrieve the EDIDs (broken or missing i2c
+	 * bus), fallback on the XGA standards.
+	 */
+	num = drm_add_modes_noedid(connector, 1920, 1200);
+
+	/* And prefer a mode pretty much anyone can handle */
+	drm_set_preferred_mode(connector, 1024, 768);
+
+	return num;
+}
+
+static enum drm_connector_status
+lsdc_connector_detect(struct drm_connector *connector, bool force)
+{
+	struct i2c_adapter *ddc = connector->ddc;
+
+	if (ddc) {
+		if (drm_probe_ddc(ddc))
+			return connector_status_connected;
+	} else {
+		if (connector->connector_type == DRM_MODE_CONNECTOR_DPI)
+			return connector_status_connected;
+
+		if (connector->connector_type == DRM_MODE_CONNECTOR_VIRTUAL)
+			return connector_status_connected;
+	}
+
+	return connector_status_unknown;
+}
+
+static struct drm_encoder *
+lsdc_connector_get_best_encoder(struct drm_connector *connector,
+				struct drm_atomic_state *state)
+{
+	struct lsdc_display_pipe *pipe = connector_to_display_pipe(connector);
+
+	return &pipe->encoder;
+}
+
+static const struct drm_connector_helper_funcs lsdc_connector_helpers = {
+	.atomic_best_encoder = lsdc_connector_get_best_encoder,
+	.get_modes = lsdc_get_modes,
+};
+
+static void lsdc_connector_destroy(struct drm_connector *connector)
+{
+	drm_connector_cleanup(connector);
+}
+
+static const struct drm_connector_funcs lsdc_connector_funcs = {
+	.detect = lsdc_connector_detect,
+	.fill_modes = drm_helper_probe_single_connector_modes,
+	.destroy = lsdc_connector_destroy,
+	.reset = drm_atomic_helper_connector_reset,
+	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+/*
+ * we provide a default support before DT/VBIOS is supported
+ */
+static int lsdc_get_encoder_type(struct lsdc_device *ldev,
+				 unsigned int index)
+{
+	const struct lsdc_desc *descp = ldev->descp;
+
+	if (descp->chip == CHIP_LS7A2000) {
+		if (index == 0)
+			return DRM_MODE_ENCODER_TMDS;
+		if (index == 1)
+			return DRM_MODE_ENCODER_TMDS;
+	}
+
+	if ((descp->chip == CHIP_LS7A1000) ||
+	    (descp->chip == CHIP_LS2K1000)) {
+		if (index == 0)
+			return DRM_MODE_ENCODER_DPI;
+		if (index == 1)
+			return DRM_MODE_ENCODER_DPI;
+	}
+
+	if (descp->chip == CHIP_LS2K0500) {
+		if (index == 0)
+			return DRM_MODE_ENCODER_DPI;
+		if (index == 1)
+			return DRM_MODE_ENCODER_DAC;
+	}
+
+	return DRM_MODE_ENCODER_NONE;
+}
+
+/*
+ * provide a default before DT/VBIOS support is upstreamed
+ */
+static int lsdc_get_connector_type(struct lsdc_device *ldev,
+				   unsigned int index)
+{
+	const struct lsdc_desc *descp = ldev->descp;
+
+	if (descp->chip == CHIP_LS7A2000) {
+		if (index == 0)
+			return DRM_MODE_CONNECTOR_HDMIA;
+		if (index == 1)
+			return DRM_MODE_CONNECTOR_HDMIA;
+	}
+
+	if ((descp->chip == CHIP_LS7A1000) ||
+	    (descp->chip == CHIP_LS2K1000)) {
+		if (index == 0)
+			return DRM_MODE_CONNECTOR_DPI;
+		if (index == 1)
+			return DRM_MODE_CONNECTOR_DPI;
+	}
+
+	if (descp->chip == CHIP_LS2K0500) {
+		if (index == 0)
+			return DRM_MODE_CONNECTOR_DPI;
+		if (index == 1)
+			return DRM_MODE_CONNECTOR_VGA;
+	}
+
+	return DRM_MODE_CONNECTOR_Unknown;
+}
+
+static void lsdc_hdmi_disable(struct drm_encoder *encoder)
+{
+	struct lsdc_display_pipe *dispipe = encoder_to_display_pipe(encoder);
+	struct drm_device *ddev = encoder->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	unsigned int index = dispipe->index;
+	u32 val;
+
+	if (index == 0)
+		val = lsdc_rreg32(ldev, HDMI0_PHY_CTRL_REG);
+	else if (index == 1)
+		val = lsdc_rreg32(ldev, HDMI1_PHY_CTRL_REG);
+
+	val &= ~HDMI_PHY_EN;
+
+	if (index == 0)
+		lsdc_wreg32(ldev, HDMI0_PHY_CTRL_REG, val);
+	else if (index == 1)
+		lsdc_wreg32(ldev, HDMI1_PHY_CTRL_REG, val);
+
+	drm_dbg(ddev, "HDMI-%u disabled\n", index);
+}
+
+static void lsdc_hdmi_enable(struct drm_encoder *encoder)
+{
+	struct drm_device *ddev = encoder->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	struct lsdc_display_pipe *dispipe = encoder_to_display_pipe(encoder);
+	unsigned int index = dispipe->index;
+	u32 val;
+
+	if (index == 0) {
+		/* Enable HDMI-0 */
+		lsdc_wreg32(ldev, HDMI0_CTRL_REG,
+				 HDMI_CTL_PERIOD_MODE |
+				 HDMI_AUDIO_EN |
+				 HDMI_PACKET_EN |
+				 HDMI_INTERFACE_EN);
+
+		lsdc_wreg32(ldev, HDMI0_ZONE_REG, 0x00400040);
+	} else if (index == 1) {
+		/* Enable HDMI-1 */
+		lsdc_wreg32(ldev, HDMI1_CTRL_REG,
+				 HDMI_CTL_PERIOD_MODE |
+				 HDMI_AUDIO_EN |
+				 HDMI_PACKET_EN |
+				 HDMI_INTERFACE_EN);
+
+		lsdc_wreg32(ldev, HDMI1_ZONE_REG, 0x00400040);
+	}
+
+	val = HDMI_PHY_TERM_STATUS |
+	      HDMI_PHY_TERM_DET_EN |
+	      HDMI_PHY_TERM_H_EN |
+	      HDMI_PHY_TERM_L_EN |
+	      HDMI_PHY_RESET_N |
+	      HDMI_PHY_EN;
+
+	if (index == 0)
+		lsdc_wreg32(ldev, HDMI0_PHY_CTRL_REG, val);
+	else if (index == 1)
+		lsdc_wreg32(ldev, HDMI1_PHY_CTRL_REG, val);
+
+	drm_dbg(ddev, "HDMI-%u enabled\n", index);
+}
+
+/*
+ *  Fout = M * Fin
+ *
+ *  M = (4 * LF) / (IDF * ODF)
+ *
+ *  Loongson HDMI require M = 10
+ */
+static void lsdc_hdmi_phy_pll_config(struct lsdc_device *ldev,
+				     int index,
+				     int clock)
+{
+	struct drm_device *ddev = &ldev->base;
+	int count = 0;
+	u32 val;
+
+	/* disable phy pll */
+	if (index == 0)
+		lsdc_wreg32(ldev, HDMI0_PHY_PLL_REG, 0x0);
+	else if (index == 1)
+		lsdc_wreg32(ldev, HDMI1_PHY_PLL_REG, 0x0);
+
+	/*
+	 * 10 = (4 * 40) / (8 * 2)
+	 */
+	val = (8 << HDMI_PLL_IDF_SHIFT) |
+	      (40 << HDMI_PLL_LF_SHIFT) |
+	      (1 << HDMI_PLL_ODF_SHIFT) |
+	      HDMI_PLL_ENABLE;
+
+	drm_dbg(ddev, "HDMI-%u clock: %d\n", index, clock);
+
+	if (index == 0)
+		lsdc_wreg32(ldev, HDMI0_PHY_PLL_REG, val);
+	else if (index == 1)
+		lsdc_wreg32(ldev, HDMI1_PHY_PLL_REG, val);
+
+	/* wait hdmi phy pll lock */
+	do {
+		if (index == 0)
+			val = lsdc_rreg32(ldev, HDMI0_PHY_PLL_REG);
+		else if (index == 1)
+			val = lsdc_rreg32(ldev, HDMI1_PHY_PLL_REG);
+
+		++count;
+
+		if (val & HDMI_PLL_LOCKED) {
+			drm_dbg(ddev, "Setting HDMI-%u PLL success(take %d cycles)\n",
+				index, count);
+			break;
+		}
+	} while (count < 1000);
+}
+
+static void lsdc_hdmi_atomic_mode_set(struct drm_encoder *encoder,
+				      struct drm_crtc_state *crtc_state,
+				      struct drm_connector_state *conn_state)
+{
+	struct drm_device *ddev = encoder->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	struct lsdc_display_pipe *dispipe = encoder_to_display_pipe(encoder);
+	unsigned int index = dispipe->index;
+	struct drm_display_mode *mode = &crtc_state->mode;
+
+	lsdc_hdmi_phy_pll_config(ldev, index, mode->clock);
+
+	drm_dbg(ddev, "HDMI-%u modeset\n", index);
+}
+
+static const struct drm_encoder_helper_funcs lsdc_hdmi_helper_funcs = {
+	.disable = lsdc_hdmi_disable,
+	.enable = lsdc_hdmi_enable,
+	.atomic_mode_set = lsdc_hdmi_atomic_mode_set,
+};
+
+static void lsdc_hdmi_reset(struct drm_encoder *encoder)
+{
+	struct drm_device *ddev = encoder->dev;
+	struct lsdc_display_pipe *dispipe = encoder_to_display_pipe(encoder);
+	unsigned int index = dispipe->index;
+
+	drm_dbg(ddev, "HDMI-%u Reset\n", index);
+}
+
+static const struct drm_encoder_funcs lsdc_encoder_funcs = {
+	.reset = lsdc_hdmi_reset,
+	.destroy = drm_encoder_cleanup,
+};
+
+int lsdc_create_output(struct lsdc_device *ldev, unsigned int index)
+{
+	const struct lsdc_desc *descp = ldev->descp;
+	struct drm_device *ddev = &ldev->base;
+	struct lsdc_display_pipe *dispipe = &ldev->dispipe[index];
+	struct drm_encoder *encoder = &dispipe->encoder;
+	struct drm_connector *connector = &dispipe->connector;
+	struct i2c_adapter *ddc = NULL;
+	struct lsdc_i2c *li2c;
+	int ret;
+
+	ret = drm_encoder_init(ddev,
+			       encoder,
+			       &lsdc_encoder_funcs,
+			       lsdc_get_encoder_type(ldev, index),
+			       "encoder-%u",
+			       index);
+	if (ret) {
+		drm_err(ddev, "Failed to init encoder: %d\n", ret);
+		return ret;
+	}
+
+	encoder->possible_crtcs = BIT(index);
+
+	if (descp->chip == CHIP_LS7A2000)
+		drm_encoder_helper_add(encoder, &lsdc_hdmi_helper_funcs);
+
+	if (descp->has_builtin_i2c) {
+		li2c = lsdc_create_i2c_chan(ddev, ldev->reg_base, index);
+		if (IS_ERR(li2c))
+			return PTR_ERR(li2c);
+
+		dispipe->li2c = li2c;
+
+		ddc = &li2c->adapter;
+	}
+
+	ret = drm_connector_init_with_ddc(ddev,
+					  connector,
+					  &lsdc_connector_funcs,
+					  lsdc_get_connector_type(ldev, index),
+					  ddc);
+	if (ret) {
+		drm_err(ddev, "Init connector-%d failed\n", index);
+		return ret;
+	}
+
+	drm_connector_helper_add(connector, &lsdc_connector_helpers);
+
+	drm_connector_attach_encoder(connector, encoder);
+
+	connector->polled = DRM_CONNECTOR_POLL_CONNECT |
+			    DRM_CONNECTOR_POLL_DISCONNECT;
+
+	connector->interlace_allowed = 0;
+	connector->doublescan_allowed = 0;
+
+	ldev->num_output++;
+
+	drm_info(ddev, "output-%u initialized\n", index);
+
+	return 0;
+}
diff --git a/drivers/gpu/drm/lsdc/lsdc_plane.c b/drivers/gpu/drm/lsdc/lsdc_plane.c
new file mode 100644
index 000000000000..0602f871bea2
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_plane.c
@@ -0,0 +1,447 @@ 
+// SPDX-License-Identifier: GPL-2.0
+
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_framebuffer.h>
+#include <drm/drm_plane_helper.h>
+#include <drm/drm_gem_vram_helper.h>
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+#include "lsdc_pll.h"
+
+static const u32 lsdc_primary_formats[] = {
+	DRM_FORMAT_XRGB8888,
+	DRM_FORMAT_ARGB8888,
+};
+
+static const u32 lsdc_cursor_formats[] = {
+	DRM_FORMAT_ARGB8888,
+};
+
+static const u64 lsdc_fb_format_modifiers[] = {
+	DRM_FORMAT_MOD_LINEAR,
+	DRM_FORMAT_MOD_INVALID
+};
+
+static void lsdc_update_fb_format(struct lsdc_device *ldev,
+				  struct drm_crtc *crtc,
+				  const struct drm_format_info *fmt_info)
+{
+	unsigned int index = drm_crtc_index(crtc);
+	u32 val;
+	u32 fmt;
+
+	switch (fmt_info->format) {
+	case DRM_FORMAT_RGB565:
+		fmt = LSDC_PF_RGB565;
+		break;
+	case DRM_FORMAT_XRGB8888:
+		fmt = LSDC_PF_XRGB8888;
+		break;
+	case DRM_FORMAT_ARGB8888:
+		fmt = LSDC_PF_XRGB8888;
+		break;
+	default:
+		fmt = LSDC_PF_XRGB8888;
+		break;
+	}
+
+	if (index == 0) {
+		val = lsdc_rreg32(ldev, LSDC_CRTC0_CFG_REG);
+		val = (val & ~CFG_PIX_FMT_MASK) | fmt;
+		lsdc_wreg32(ldev, LSDC_CRTC0_CFG_REG, val);
+	} else if (index == 1) {
+		val = lsdc_rreg32(ldev, LSDC_CRTC1_CFG_REG);
+		val = (val & ~CFG_PIX_FMT_MASK) | fmt;
+		lsdc_wreg32(ldev, LSDC_CRTC1_CFG_REG, val);
+	}
+}
+
+static void lsdc_update_fb_start_addr(struct lsdc_device *ldev,
+				      struct drm_crtc *crtc,
+				      u64 paddr)
+{
+	struct drm_device *ddev = &ldev->base;
+	unsigned int index = drm_crtc_index(crtc);
+	u32 lo_addr_reg;
+	u32 hi_addr_reg;
+	u32 val;
+
+	/*
+	 * Find which framebuffer address register should update.
+	 * if FB_ADDR0_REG is in using, we write the address to FB_ADDR0_REG,
+	 * if FB_ADDR1_REG is in using, we write the address to FB_ADDR1_REG
+	 * for each CRTC, the switch using one fb register to another is
+	 * trigger by triggered by set CFG_PAGE_FLIP bit of LSDC_CRTCx_CFG_REG
+	 */
+	if (index == 0) {
+		val = lsdc_rreg32(ldev, LSDC_CRTC0_CFG_REG);
+		if (val & CFG_FB_IN_USING) {
+			lo_addr_reg = LSDC_CRTC0_FB1_LO_ADDR_REG;
+			hi_addr_reg = LSDC_CRTC0_FB1_HI_ADDR_REG;
+			drm_dbg(ddev, "Currently, FB1 is in using by CRTC-0\n");
+		} else {
+			lo_addr_reg = LSDC_CRTC0_FB0_LO_ADDR_REG;
+			hi_addr_reg = LSDC_CRTC0_FB0_HI_ADDR_REG;
+			drm_dbg(ddev, "Currently, FB0 is in using by CRTC-0\n");
+		}
+	} else if (index == 1) {
+		val = lsdc_rreg32(ldev, LSDC_CRTC1_CFG_REG);
+		if (val & CFG_FB_IN_USING) {
+			lo_addr_reg = LSDC_CRTC1_FB1_LO_ADDR_REG;
+			hi_addr_reg = LSDC_CRTC1_FB1_HI_ADDR_REG;
+			drm_dbg(ddev, "Currently, FB1 is in using by CRTC-1\n");
+		} else {
+			lo_addr_reg = LSDC_CRTC1_FB0_LO_ADDR_REG;
+			hi_addr_reg = LSDC_CRTC1_FB0_HI_ADDR_REG;
+			drm_dbg(ddev, "Currently, FB0 is in using by CRTC-1\n");
+		}
+	}
+
+	/* 40-bit width physical address bus */
+	lsdc_wreg32(ldev, lo_addr_reg, paddr);
+	lsdc_wreg32(ldev, hi_addr_reg, (paddr >> 32) & 0xFF);
+
+	drm_dbg(ddev, "CRTC-%u scantout from 0x%llx\n", index, paddr);
+}
+
+static unsigned int lsdc_get_fb_offset(struct drm_framebuffer *fb,
+				       struct drm_plane_state *state,
+				       unsigned int plane)
+{
+	unsigned int offset = fb->offsets[plane];
+
+	offset += fb->format->cpp[plane] * (state->src_x >> 16);
+	offset += fb->pitches[plane] * (state->src_y >> 16);
+
+	return offset;
+}
+
+static s64 lsdc_get_vram_bo_offset(struct drm_framebuffer *fb)
+{
+	struct drm_gem_vram_object *gbo;
+	s64 gpu_addr;
+
+	gbo = drm_gem_vram_of_gem(fb->obj[0]);
+	gpu_addr = drm_gem_vram_offset(gbo);
+
+	return gpu_addr;
+}
+
+static int lsdc_primary_plane_atomic_check(struct drm_plane *plane,
+					   struct drm_atomic_state *state)
+{
+	struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane);
+	struct drm_crtc *crtc = plane_state->crtc;
+	struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
+
+	if (!crtc)
+		return 0;
+
+	return drm_atomic_helper_check_plane_state(plane_state,
+						   crtc_state,
+						   DRM_PLANE_NO_SCALING,
+						   DRM_PLANE_NO_SCALING,
+						   false,
+						   true);
+}
+
+static void lsdc_update_fb_stride(struct lsdc_device *ldev,
+				  struct drm_crtc *crtc,
+				  unsigned int stride)
+{
+	unsigned int index = drm_crtc_index(crtc);
+
+	if (index == 0)
+		lsdc_wreg32(ldev, LSDC_CRTC0_STRIDE_REG, stride);
+	else if (index == 1)
+		lsdc_wreg32(ldev, LSDC_CRTC1_STRIDE_REG, stride);
+
+	drm_dbg(crtc->dev, "update stride to %u\n", stride);
+}
+
+static void lsdc_primary_plane_atomic_update(struct drm_plane *plane,
+					     struct drm_atomic_state *state)
+{
+	struct lsdc_device *ldev = to_lsdc(plane->dev);
+	struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
+	struct drm_crtc *crtc = new_plane_state->crtc;
+	struct drm_framebuffer *fb = new_plane_state->fb;
+	u32 fb_offset = lsdc_get_fb_offset(fb, new_plane_state, 0);
+	dma_addr_t fb_addr;
+	s64 gpu_addr;
+
+	gpu_addr = lsdc_get_vram_bo_offset(fb);
+	if (gpu_addr < 0)
+		return;
+
+	fb_addr = ldev->vram_base + gpu_addr + fb_offset;
+
+	lsdc_update_fb_start_addr(ldev, crtc, fb_addr);
+
+	lsdc_update_fb_stride(ldev, crtc, fb->pitches[0]);
+
+	lsdc_update_fb_format(ldev, crtc, fb->format);
+}
+
+static void lsdc_primary_plane_atomic_disable(struct drm_plane *plane,
+					      struct drm_atomic_state *state)
+{
+	drm_dbg(plane->dev, "%s disabled\n", plane->name);
+}
+
+static const struct drm_plane_helper_funcs lsdc_primary_plane_helpers = {
+	.prepare_fb = drm_gem_vram_plane_helper_prepare_fb,
+	.cleanup_fb = drm_gem_vram_plane_helper_cleanup_fb,
+	.atomic_check = lsdc_primary_plane_atomic_check,
+	.atomic_update = lsdc_primary_plane_atomic_update,
+	.atomic_disable = lsdc_primary_plane_atomic_disable,
+};
+
+static int lsdc_cursor_atomic_check(struct drm_plane *plane,
+				    struct drm_atomic_state *state)
+{
+	struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
+	struct drm_framebuffer *fb = new_plane_state->fb;
+	struct drm_crtc *crtc = new_plane_state->crtc;
+	struct drm_crtc_state *crtc_state;
+	int ret;
+
+	/* no need for further checks if the plane is being disabled */
+	if (!crtc || !fb)
+		return 0;
+
+	if (!new_plane_state->visible)
+		return 0;
+
+	crtc_state = drm_atomic_get_new_crtc_state(state,
+						   new_plane_state->crtc);
+
+	ret = drm_atomic_helper_check_plane_state(new_plane_state,
+						  crtc_state,
+						  DRM_PLANE_NO_SCALING,
+						  DRM_PLANE_NO_SCALING,
+						  true,
+						  true);
+
+	return ret;
+}
+
+/*
+ * Update the location of the cursor, attach to CRTC0 or CRTC1
+ *
+ * There is only one hardware cursor in ls7a1000, ls2k1000 and ls2k0500.
+ * we made it shared by the two CRTC, which can satisfy the peoples who
+ * use double screen extend mode only. On clone screen case, the cursor
+ * on display pipe 1 will only not be able to display.
+ */
+static void lsdc_cursor_update_location_quirks(struct lsdc_device *ldev,
+					       struct drm_crtc *crtc)
+{
+	u32 val = CURSOR_FORMAT_ARGB8888;
+
+	/*
+	 * if bit 4 of LSDC_CURSOR0_CFG_REG is 1, then the cursor will be
+	 * locate at CRTC-1, if bit 4 of LSDC_CURSOR0_CFG_REG is 0, then
+	 * the cursor will be locate at CRTC-0. In this way, one hardware
+	 * cursor can be shared by two CRTCs on extend screen usage. The
+	 * CRTC will cpmposite the fb and crusor automatically, and the
+	 * cursor is alway on the top of the primary.
+	 */
+	if (drm_crtc_index(crtc))
+		val |= CURSOR_LOCATION;
+
+	lsdc_wreg32(ldev, LSDC_CURSOR0_CFG_REG, val);
+}
+
+/* update the position of the cursor */
+static void lsdc_cursor_update_position_quirks(struct lsdc_device *ldev,
+					       int x,
+					       int y)
+{
+	if (x < 0)
+		x = 0;
+
+	if (y < 0)
+		y = 0;
+
+	lsdc_wreg32(ldev, LSDC_CURSOR0_POSITION_REG, (y << 16) | x);
+}
+
+static void lsdc_cursor_atomic_update_quirks(struct drm_plane *plane,
+					     struct drm_atomic_state *state)
+{
+	struct drm_device *ddev = plane->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
+	struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane);
+	struct drm_framebuffer *new_fb = new_plane_state->fb;
+	struct drm_framebuffer *old_fb = old_plane_state->fb;
+
+	if (new_fb != old_fb) {
+		s64 offset = lsdc_get_vram_bo_offset(new_fb);
+		u64 cursor_addr = ldev->vram_base + offset;
+
+		drm_dbg_kms(ddev, "%s offset: %llx\n", plane->name, offset);
+
+		lsdc_wreg32(ldev, LSDC_CURSOR0_ADDR_LO_REG, cursor_addr);
+		lsdc_wreg32(ldev, LSDC_CURSOR0_ADDR_HI_REG, (cursor_addr >> 32) & 0xFF);
+	}
+
+	lsdc_cursor_update_position_quirks(ldev, new_plane_state->crtc_x, new_plane_state->crtc_y);
+
+	lsdc_cursor_update_location_quirks(ldev, new_plane_state->crtc);
+}
+
+/* update the format, size and location of the cursor */
+static void lsdc_cursor_atomic_update(struct drm_plane *plane,
+				      struct drm_atomic_state *state)
+{
+	struct drm_device *ddev = plane->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	struct lsdc_display_pipe *dispipe = cursor_to_display_pipe(plane);
+	struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
+	struct drm_framebuffer *new_fb = new_plane_state->fb;
+	int x = new_plane_state->crtc_x;
+	int y = new_plane_state->crtc_y;
+	u32 conf = CURSOR_FORMAT_ARGB8888 | CURSOR_SIZE_64X64;
+	u64 cursor_addr = ldev->vram_base + lsdc_get_vram_bo_offset(new_fb);
+
+	if (x < 0)
+		x = 0;
+
+	if (y < 0)
+		y = 0;
+
+	if (dispipe->index == 0) {
+		lsdc_wreg32(ldev, LSDC_CURSOR0_ADDR_HI_REG, (cursor_addr >> 32) & 0xFF);
+		lsdc_wreg32(ldev, LSDC_CURSOR0_ADDR_LO_REG, cursor_addr);
+		/* Attach Cursor-0 to CRTC-0 */
+		lsdc_wreg32(ldev, LSDC_CURSOR0_CFG_REG, conf & ~CURSOR_LOCATION);
+		lsdc_wreg32(ldev, LSDC_CURSOR0_POSITION_REG, (y << 16) | x);
+		return;
+	}
+
+	if (dispipe->index == 1) {
+		lsdc_wreg32(ldev, LSDC_CURSOR1_ADDR_HI_REG, (cursor_addr >> 32) & 0xFF);
+		lsdc_wreg32(ldev, LSDC_CURSOR1_ADDR_LO_REG, cursor_addr);
+		/* Attach Cursor-1 to CRTC-1 */
+		lsdc_wreg32(ldev, LSDC_CURSOR1_CFG_REG, conf | CURSOR_LOCATION);
+		lsdc_wreg32(ldev, LSDC_CURSOR1_POSITION_REG, (y << 16) | x);
+		return;
+	}
+}
+
+static void lsdc_cursor_atomic_disable_quirks(struct drm_plane *plane,
+					      struct drm_atomic_state *state)
+{
+	struct drm_device *ddev = plane->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+
+	/* Set the format to 0 actually display the cursor */
+	lsdc_wreg32(ldev, LSDC_CURSOR0_CFG_REG, 0);
+
+	drm_dbg(ddev, "%s disabled\n", plane->name);
+}
+
+static void lsdc_cursor_atomic_disable(struct drm_plane *plane,
+				       struct drm_atomic_state *state)
+{
+	struct drm_device *ddev = plane->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	struct lsdc_display_pipe *dispipe = cursor_to_display_pipe(plane);
+
+	if (dispipe->index == 0)
+		lsdc_wreg32(ldev, LSDC_CURSOR0_CFG_REG, 0);
+	else if (dispipe->index == 1)
+		lsdc_wreg32(ldev, LSDC_CURSOR1_CFG_REG, 0);
+
+	drm_dbg(ddev, "%s disabled\n", plane->name);
+}
+
+static const struct drm_plane_helper_funcs lsdc_cursor_helpers_quirk = {
+	.prepare_fb = drm_gem_vram_plane_helper_prepare_fb,
+	.cleanup_fb = drm_gem_vram_plane_helper_cleanup_fb,
+	.atomic_check = lsdc_cursor_atomic_check,
+	.atomic_update = lsdc_cursor_atomic_update_quirks,
+	.atomic_disable = lsdc_cursor_atomic_disable_quirks,
+};
+
+static const struct drm_plane_helper_funcs lsdc_cursor_plane_helpers = {
+	.prepare_fb = drm_gem_vram_plane_helper_prepare_fb,
+	.cleanup_fb = drm_gem_vram_plane_helper_cleanup_fb,
+	.atomic_check = lsdc_cursor_atomic_check,
+	.atomic_update = lsdc_cursor_atomic_update,
+	.atomic_disable = lsdc_cursor_atomic_disable,
+};
+
+static const struct drm_plane_funcs lsdc_plane_funcs = {
+	.update_plane = drm_atomic_helper_update_plane,
+	.disable_plane = drm_atomic_helper_disable_plane,
+	.destroy = drm_plane_cleanup,
+	.reset = drm_atomic_helper_plane_reset,
+	.atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_plane_destroy_state,
+};
+
+static const struct drm_plane_helper_funcs *
+lsdc_get_cursor_helper_funcs(const struct lsdc_desc *descp)
+{
+	if (descp->chip == CHIP_LS7A2000)
+		return &lsdc_cursor_plane_helpers;
+
+	return &lsdc_cursor_helpers_quirk;
+}
+
+int lsdc_plane_init(struct lsdc_device *ldev,
+		    struct drm_plane *plane,
+		    enum drm_plane_type type,
+		    unsigned int index)
+{
+	const struct lsdc_desc *descp = ldev->descp;
+	struct drm_device *ddev = &ldev->base;
+	unsigned int format_count;
+	const u32 *formats;
+	const char *name;
+	int ret;
+
+	switch (type) {
+	case DRM_PLANE_TYPE_PRIMARY:
+		formats = lsdc_primary_formats;
+		format_count = ARRAY_SIZE(lsdc_primary_formats);
+		name = "primary-%u";
+		break;
+	case DRM_PLANE_TYPE_CURSOR:
+		formats = lsdc_cursor_formats;
+		format_count = ARRAY_SIZE(lsdc_cursor_formats);
+		name = "cursor-%u";
+		break;
+	case DRM_PLANE_TYPE_OVERLAY:
+		drm_err(ddev, "overlay plane is not supported\n");
+		break;
+	}
+
+	ret = drm_universal_plane_init(ddev, plane, 1 << index,
+				       &lsdc_plane_funcs,
+				       formats, format_count,
+				       lsdc_fb_format_modifiers,
+				       type, name, index);
+	if (ret) {
+		drm_err(ddev, "%s failed: %d\n", __func__, ret);
+		return ret;
+	}
+
+	switch (type) {
+	case DRM_PLANE_TYPE_PRIMARY:
+		drm_plane_helper_add(plane, &lsdc_primary_plane_helpers);
+		break;
+	case DRM_PLANE_TYPE_CURSOR:
+		drm_plane_helper_add(plane, lsdc_get_cursor_helper_funcs(descp));
+		break;
+	case DRM_PLANE_TYPE_OVERLAY:
+		drm_err(ddev, "overlay plane is not supported\n");
+		break;
+	}
+
+	return 0;
+}
diff --git a/drivers/gpu/drm/lsdc/lsdc_pll.c b/drivers/gpu/drm/lsdc/lsdc_pll.c
new file mode 100644
index 000000000000..4210cfa73451
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_pll.c
@@ -0,0 +1,571 @@ 
+// SPDX-License-Identifier: GPL-2.0
+
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+#include "lsdc_pll.h"
+
+/*
+ * The structure of the pixel PLL register is evolved with times.
+ * All loongson's cpu is little endian.
+ */
+
+/* u64 */
+struct ls7a1000_pixpll_bitmap {
+	/* Byte 0 ~ Byte 3 */
+	unsigned div_out      : 7;   /*  0 : 6     output clock divider  */
+	unsigned reserved_1   : 14;  /*  7 : 20                          */
+	unsigned loopc        : 9;   /* 21 : 29                          */
+	unsigned reserved_2   : 2;   /* 30 : 31                          */
+
+	/* Byte 4 ~ Byte 7 */
+	unsigned div_ref      : 7;   /*  0 : 6     input clock divider   */
+	unsigned locked       : 1;   /*  7         PLL locked flag       */
+	unsigned sel_out      : 1;   /*  8         output clk selector   */
+	unsigned reserved_3   : 2;   /*  9 : 10    reserved              */
+	unsigned set_param    : 1;   /*  11        set pll param         */
+	unsigned bypass       : 1;   /*  12                              */
+	unsigned powerdown    : 1;   /*  13                              */
+	unsigned reserved_4   : 18;  /*  14 : 31                         */
+};
+
+/* u128 */
+struct ls2k1000_pixpll_bitmap {
+	/* Byte 0 ~ Byte 3 */
+	unsigned sel_out      :  1;  /*  0      select this PLL          */
+	unsigned reserved_1   :  1;  /*  1                               */
+	unsigned sw_adj_en    :  1;  /*  2      allow software adjust    */
+	unsigned bypass       :  1;  /*  3      bypass L1 PLL            */
+	unsigned reserved_2   :  3;  /*  4:6                             */
+	unsigned lock_en      :  1;  /*  7      enable lock L1 PLL       */
+	unsigned reserved_3   :  2;  /*  8:9                             */
+	unsigned lock_check   :  2;  /* 10:11   precision check          */
+	unsigned reserved_4   :  4;  /* 12:15                            */
+
+	unsigned locked       :  1;  /* 16      PLL locked flag bit      */
+	unsigned reserved_5   :  2;  /* 17:18                            */
+	unsigned powerdown    :  1;  /* 19      powerdown the pll if set */
+	unsigned reserved_6   :  6;  /* 20:25                            */
+	unsigned div_ref      :  6;  /* 26:31   L1 Prescaler             */
+
+	/* Byte 4 ~ Byte 7 */
+	unsigned loopc        : 10;  /* 32:41   Clock Multiplier         */
+	unsigned l1_div       :  6;  /* 42:47   not used                 */
+	unsigned reserved_7   : 16;  /* 48:63                            */
+
+	/* Byte 8 ~ Byte 15 */
+	unsigned div_out      :  6;  /* 0 : 5   output clock divider     */
+	unsigned reserved_8   : 26;  /* 6 : 31                           */
+	unsigned reserved_9   : 32;  /* 70: 127                          */
+};
+
+/* u32 */
+struct ls2k0500_pixpll_bitmap {
+	/* Byte 0 ~ Byte 1 */
+	unsigned sel_out      : 1;
+	unsigned reserved_1   : 2;
+	unsigned sw_adj_en    : 1;   /* allow software adjust              */
+	unsigned bypass       : 1;   /* bypass L1 PLL                      */
+	unsigned powerdown    : 1;   /* write 1 to powerdown the PLL       */
+	unsigned reserved_2   : 1;
+	unsigned locked       : 1;   /*  7     Is L1 PLL locked, read only */
+	unsigned div_ref      : 6;   /*  8:13  ref clock divider           */
+	unsigned reserved_3   : 2;   /* 14:15                              */
+	/* Byte 2 ~ Byte 3 */
+	unsigned loopc        : 8;   /* 16:23   Clock Multiplier           */
+	unsigned div_out      : 6;   /* 24:29   output clock divider       */
+	unsigned reserved_4   : 2;   /* 30:31                              */
+};
+
+union lsdc_pixpll_bitmap {
+	struct ls7a1000_pixpll_bitmap ls7a1000;
+	struct ls2k1000_pixpll_bitmap ls2k1000;
+	struct ls2k0500_pixpll_bitmap ls2k0500;
+
+	u32 dword[4];
+};
+
+struct pixclk_to_pll_parm {
+	/* kHz */
+	unsigned int clock;
+
+	/* unrelated information */
+	unsigned short width;
+	unsigned short height;
+	unsigned short vrefresh;
+
+	/* Stores parameters for programming the Hardware PLLs */
+	unsigned short div_out;
+	unsigned short loopc;
+	unsigned short div_ref;
+};
+
+/*
+ * Pixel clock to PLL parameters translation table.
+ * Small static cached value to speed up PLL parameters calculation.
+ */
+static const struct pixclk_to_pll_parm pll_param_table[] = {
+	{148500, 1920, 1080, 60, 11, 49,  3},   /* 1920x1080@60Hz */
+						/* 1920x1080@50Hz */
+	{174500, 1920, 1080, 75, 17, 89,  3},   /* 1920x1080@75Hz */
+	{181250, 2560, 1080, 75,  8, 58,  4},   /* 2560x1080@75Hz */
+	{146250, 1680, 1050, 60, 16, 117, 5},   /* 1680x1050@60Hz */
+	{135000, 1280, 1024, 75, 10, 54,  4},   /* 1280x1024@75Hz */
+
+	{108000, 1600, 900,  60, 15, 81,  5},   /* 1600x900@60Hz  */
+						/* 1280x1024@60Hz */
+						/* 1280x960@60Hz */
+						/* 1152x864@75Hz */
+
+	{106500, 1440, 900,  60, 19, 81,  4},   /* 1440x900@60Hz */
+	{88750,  1440, 900,  60, 16, 71,  5},   /* 1440x900@60Hz */
+	{83500,  1280, 800,  60, 17, 71,  5},   /* 1280x800@60Hz */
+	{71000,  1280, 800,  60, 20, 71,  5},   /* 1280x800@60Hz */
+
+	{74250,  1280, 720,  60, 22, 49,  3},   /* 1280x720@60Hz */
+						/* 1280x720@50Hz */
+
+	{78750,  1024, 768,  75, 16, 63,  5},   /* 1024x768@75Hz */
+	{75000,  1024, 768,  70, 29, 87,  4},   /* 1024x768@70Hz */
+	{65000,  1024, 768,  60, 20, 39,  3},   /* 1024x768@60Hz */
+
+	{51200,  1024, 600,  60, 25, 64,  5},   /* 1024x600@60Hz */
+
+	{57284,  832,  624,  75, 24, 55,  4},   /* 832x624@75Hz */
+	{49500,  800,  600,  75, 40, 99,  5},   /* 800x600@75Hz */
+	{50000,  800,  600,  72, 44, 88,  4},   /* 800x600@72Hz */
+	{40000,  800,  600,  60, 30, 36,  3},   /* 800x600@60Hz */
+	{36000,  800,  600,  56, 50, 72,  4},   /* 800x600@56Hz */
+	{31500,  640,  480,  75, 40, 63,  5},   /* 640x480@75Hz */
+						/* 640x480@73Hz */
+
+	{30240,  640,  480,  67, 62, 75,  4},   /* 640x480@67Hz */
+	{27000,  720,  576,  50, 50, 54,  4},   /* 720x576@60Hz */
+	{25175,  640,  480,  60, 85, 107, 5},   /* 640x480@60Hz */
+	{25200,  640,  480,  60, 50, 63,  5},   /* 640x480@60Hz */
+						/* 720x480@60Hz */
+};
+
+/**
+ * lsdc_pixpll_setup - ioremap the device dependent PLL registers
+ *
+ * @this: point to the object which this function is called from
+ */
+static int lsdc_pixpll_setup(struct lsdc_pll * const this)
+{
+	this->mmio = ioremap(this->reg_base, this->reg_size);
+
+	return 0;
+}
+
+/*
+ * Find a set of pll parameters (to generate pixel clock) from a static
+ * local table, which avoid to compute the pll parameter eachtime a
+ * modeset is triggered.
+ *
+ * @this: point to the object which this function is called from
+ * @clock: the desired output pixel clock, the unit is kHz
+ * @pout: point to where the parameters to store if found
+ *
+ *  Return true if hit, otherwise return false.
+ */
+static bool lsdc_pixpll_find(struct lsdc_pll * const this,
+			     unsigned int clock,
+			     struct lsdc_pll_parms * const pout)
+{
+	unsigned int num = ARRAY_SIZE(pll_param_table);
+	unsigned int i;
+
+	for (i = 0; i < num; i++) {
+		if (clock != pll_param_table[i].clock)
+			continue;
+
+		pout->div_ref = pll_param_table[i].div_ref;
+		pout->loopc   = pll_param_table[i].loopc;
+		pout->div_out = pll_param_table[i].div_out;
+
+		return true;
+	}
+
+	drm_dbg(this->ddev, "pixel clock %u: miss\n", clock);
+
+	return false;
+}
+
+/*
+ * Find a set of pll parameters which have minimal difference with the desired
+ * pixel clock frequency. It does that by computing all of the possible
+ * combination. Compute the diff and find the combination with minimal diff.
+ *
+ *  clock_out = refclk / div_ref * loopc / div_out
+ *
+ *  refclk is determined by the oscillator mounted board(Here is 100MHz in
+ *  almost all case)
+ *
+ * @this: point to the object from which this function is called
+ * @clock_khz: the desired output pixel clock, the unit is kHz
+ * @pout: point to the out struct of lsdc_pll_parms
+ *
+ *  Return true if a parameter is found, otherwise return false
+ */
+static bool lsdc_pixpll_compute(struct lsdc_pll * const this,
+				unsigned int clock_khz,
+				struct lsdc_pll_parms *pout)
+{
+	unsigned int refclk = this->ref_clock;
+	const unsigned int tolerance = 1000;
+	unsigned int min = tolerance;
+	unsigned int div_out, loopc, div_ref;
+	unsigned int computed;
+
+	if (lsdc_pixpll_find(this, clock_khz, pout))
+		return true;
+
+	for (div_out = 6; div_out < 64; div_out++) {
+		for (div_ref = 3; div_ref < 6; div_ref++) {
+			for (loopc = 6; loopc < 161; loopc++) {
+				int diff;
+
+				if (loopc < 12 * div_ref)
+					continue;
+				if (loopc > 32 * div_ref)
+					continue;
+
+				computed = refclk * loopc / div_ref / div_out;
+
+				if (clock_khz > computed)
+					diff = clock_khz - computed;
+				else if (clock_khz < computed)
+					diff = computed - clock_khz;
+
+				if (diff < min) {
+					min = diff;
+					pout->div_ref = div_ref;
+					pout->div_out = div_out;
+					pout->loopc = loopc;
+
+					if (diff == 0)
+						return true;
+				}
+			}
+		}
+	}
+
+	return min < tolerance;
+}
+
+/*
+ * Update the pll parameters to hardware, target to the pixpll in ls7a1000
+ *
+ * @this: point to the object from which this function is called
+ * @pin: point to the struct of lsdc_pll_parms passed in
+ *
+ * return 0 if successful.
+ */
+static int ls7a1000_pixpll_param_update(struct lsdc_pll * const this,
+					struct lsdc_pll_parms const *pin)
+{
+	void __iomem *reg = this->mmio;
+	unsigned int counter = 0;
+	bool locked;
+	u32 val;
+
+	/* Bypass the software configured PLL, using refclk directly */
+	val = readl(reg + 0x4);
+	val &= ~(1 << 8);
+	writel(val, reg + 0x4);
+
+	/* Powerdown the PLL */
+	val = readl(reg + 0x4);
+	val |= (1 << 13);
+	writel(val, reg + 0x4);
+
+	/* Clear the pll parameters */
+	val = readl(reg + 0x4);
+	val &= ~(1 << 11);
+	writel(val, reg + 0x4);
+
+	/* clear old value & config new value */
+	val = readl(reg + 0x04);
+	val &= ~0x7F;
+	val |= pin->div_ref;        /* div_ref */
+	writel(val, reg + 0x4);
+
+	val = readl(reg);
+	val &= ~0x7f;
+	val |= pin->div_out;        /* div_out */
+
+	val &= ~(0x1ff << 21);
+	val |= pin->loopc << 21;    /* loopc */
+	writel(val, reg);
+
+	/* Set the pll the parameters */
+	val = readl(reg + 0x4);
+	val |= (1 << 11);
+	writel(val, reg + 0x4);
+
+	/* Powerup the PLL */
+	val = readl(reg + 0x4);
+	val &= ~(1 << 13);
+	writel(val, reg + 0x4);
+
+	/* Wait the PLL lock */
+	do {
+		val = readl(reg + 0x4);
+		locked = val & 0x80;
+		counter++;
+	} while (!locked && (counter < 10000));
+
+	drm_dbg(this->ddev, "%u loop waited\n", counter);
+
+	/* Switch to the software configured pll */
+	val = readl(reg + 0x4);
+	val |= (1UL << 8);
+	writel(val, reg + 0x4);
+
+	return 0;
+}
+
+/*
+ * Update the pll parameters to hardware, target to the pixpll in ls2k1000
+ *
+ * @this: point to the object from which this function is called
+ * @pin: point to the struct of lsdc_pll_parms passed in
+ *
+ * return 0 if successful.
+ */
+static int ls2k1000_pixpll_param_update(struct lsdc_pll * const this,
+					struct lsdc_pll_parms const *pin)
+{
+	void __iomem *reg = this->mmio;
+	unsigned int counter = 0;
+	bool locked = false;
+	u32 val;
+
+	val = readl(reg);
+	/* Bypass the software configured PLL, using refclk directly */
+	val &= ~(1 << 0);
+	writel(val, reg);
+
+	/* Powerdown the PLL */
+	val |= (1 << 19);
+	writel(val, reg);
+
+	/* Allow the software configuration */
+	val &= ~(1 << 2);
+	writel(val, reg);
+
+	/* allow L1 PLL lock */
+	val = (1L << 7) | (3L << 10);
+	writel(val, reg);
+
+	/* clear div_ref bit field */
+	val &= ~(0x3f << 26);
+	/* set div_ref bit field */
+	val |= pin->div_ref << 26;
+	writel(val, reg);
+
+	val = readl(reg + 4);
+	/* clear loopc bit field */
+	val &= ~0x0fff;
+	/* set loopc bit field */
+	val |= pin->loopc;
+	writel(val, reg + 4);
+
+	/* set div_out */
+	writel(pin->div_out, reg + 8);
+
+	val = readl(reg);
+	/* use this parms configured just now */
+	val |= (1 << 2);
+	/* powerup the PLL */
+	val &= ~(1 << 19);
+	writel(val, reg);
+
+	/* wait pll setup and locked */
+	do {
+		val = readl(reg);
+		locked = val & 0x10000;
+		counter++;
+	} while (!locked && (counter < 10000));
+
+	drm_dbg(this->ddev, "%u loop waited\n", counter);
+
+	/* Switch to the above software configured PLL instead of refclk */
+	val |= 1;
+	writel(val, reg);
+
+	return 0;
+}
+
+/*
+ * Update the pll parameters to hardware, target to the pixpll in ls2k0500
+ *
+ * @this: point to the object which calling this function
+ * @param: pointer to where the parameters passed in
+ *
+ * return 0 if successful.
+ */
+static int ls2k0500_pixpll_param_update(struct lsdc_pll * const this,
+					struct lsdc_pll_parms const *param)
+{
+	void __iomem *reg = this->mmio;
+	unsigned int counter = 0;
+	bool locked = false;
+	u32 val;
+
+	/* Bypass the software configured PLL, using refclk directly */
+	val = readl(reg);
+	val &= ~(1 << 0);
+	writel(val, reg);
+
+	/* Powerdown the PLL */
+	val = readl(reg);
+	val |= (1 << 5);
+	writel(val, reg);
+
+	/* Allow the software configuration */
+	val |= (1 << 3);
+	writel(val, reg);
+
+	/* Update the pll params */
+	val = (param->div_out << 24) |
+	      (param->loopc << 16) |
+	      (param->div_ref << 8);
+
+	writel(val, reg);
+
+	/* Powerup the PLL */
+	val = readl(reg);
+	val &= ~(1 << 5);
+	writel(val, reg);
+
+	/* wait pll setup and locked */
+	do {
+		val = readl(reg);
+		locked = val & 0x80;
+		counter++;
+	} while (!locked && (counter < 10000));
+
+	drm_dbg(this->ddev, "%u loop waited\n", counter);
+
+	/* Switch to the above software configured PLL instead of refclk */
+	writel((val | 1), reg);
+
+	return 0;
+}
+
+static unsigned int lsdc_get_clock_rate(struct lsdc_pll * const this,
+					struct lsdc_pll_parms *pout)
+{
+	struct drm_device *ddev = this->ddev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	const struct lsdc_desc * const descp = ldev->descp;
+	unsigned int out;
+	union lsdc_pixpll_bitmap parms;
+
+	if ((descp->chip == CHIP_LS7A1000) ||
+	    (descp->chip == CHIP_LS7A2000)) {
+		struct ls7a1000_pixpll_bitmap *obj = &parms.ls7a1000;
+
+		parms.dword[0] = readl(this->mmio);
+		parms.dword[1] = readl(this->mmio + 4);
+		out = this->ref_clock / obj->div_ref * obj->loopc / obj->div_out;
+		if (pout) {
+			pout->div_ref = obj->div_ref;
+			pout->loopc = obj->loopc;
+			pout->div_out = obj->div_out;
+		}
+	} else if (descp->chip == CHIP_LS2K1000) {
+		struct ls2k1000_pixpll_bitmap *obj = &parms.ls2k1000;
+
+		parms.dword[0] = readl(this->mmio);
+		parms.dword[1] = readl(this->mmio + 4);
+		parms.dword[2] = readl(this->mmio + 8);
+		parms.dword[3] = readl(this->mmio + 12);
+		out = this->ref_clock / obj->div_ref * obj->loopc / obj->div_out;
+		if (pout) {
+			pout->div_ref = obj->div_ref;
+			pout->loopc = obj->loopc;
+			pout->div_out = obj->div_out;
+		}
+	} else if (descp->chip == CHIP_LS2K0500) {
+		struct ls2k0500_pixpll_bitmap *obj = &parms.ls2k0500;
+
+		parms.dword[0] = readl(this->mmio);
+		out = this->ref_clock / obj->div_ref * obj->loopc / obj->div_out;
+		if (pout) {
+			pout->div_ref = obj->div_ref;
+			pout->loopc = obj->loopc;
+			pout->div_out = obj->div_out;
+		}
+	} else {
+		drm_err(ddev, "unknown chip, the driver need update\n");
+		return 0;
+	}
+
+	return out;
+}
+
+static const struct lsdc_pixpll_funcs ls7a1000_pixpll_funcs = {
+	.setup = lsdc_pixpll_setup,
+	.compute = lsdc_pixpll_compute,
+	.update = ls7a1000_pixpll_param_update,
+	.get_clock_rate = lsdc_get_clock_rate,
+};
+
+static const struct lsdc_pixpll_funcs ls2k1000_pixpll_funcs = {
+	.setup = lsdc_pixpll_setup,
+	.compute = lsdc_pixpll_compute,
+	.update = ls2k1000_pixpll_param_update,
+	.get_clock_rate = lsdc_get_clock_rate,
+};
+
+static const struct lsdc_pixpll_funcs ls2k0500_pixpll_funcs = {
+	.setup = lsdc_pixpll_setup,
+	.compute = lsdc_pixpll_compute,
+	.update = ls2k0500_pixpll_param_update,
+	.get_clock_rate = lsdc_get_clock_rate,
+};
+
+int lsdc_pixpll_init(struct lsdc_pll * const this,
+		     struct drm_device *ddev,
+		     unsigned int index)
+{
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	const struct lsdc_desc *descp = ldev->descp;
+
+	this->ddev = ddev;
+	this->index = index;
+	this->ref_clock = LSDC_PLL_REF_CLK;
+
+	/* LS7A1000 and LS7A2000's pixpll setting registers is same */
+	if ((descp->chip == CHIP_LS7A2000) || (descp->chip == CHIP_LS7A1000)) {
+		if (index == 0)
+			this->reg_base = LS7A1000_CFG_REG_BASE + LS7A1000_PIX_PLL0_REG;
+		else if (index == 1)
+			this->reg_base = LS7A1000_CFG_REG_BASE + LS7A1000_PIX_PLL1_REG;
+		this->reg_size = 8;
+		this->funcs = &ls7a1000_pixpll_funcs;
+	} else if (descp->chip == CHIP_LS2K1000) {
+		if (index == 0)
+			this->reg_base = LS2K1000_CFG_REG_BASE + LS2K1000_PIX_PLL0_REG;
+		else if (index == 1)
+			this->reg_base = LS2K1000_CFG_REG_BASE + LS2K1000_PIX_PLL1_REG;
+
+		this->reg_size = 16;
+		this->funcs = &ls2k1000_pixpll_funcs;
+	} else if (descp->chip == CHIP_LS2K0500) {
+		if (index == 0)
+			this->reg_base = LS2K0500_CFG_REG_BASE + LS2K0500_PIX_PLL0_REG;
+		else if (index == 1)
+			this->reg_base = LS2K0500_CFG_REG_BASE + LS2K0500_PIX_PLL1_REG;
+
+		this->reg_size = 4;
+		this->funcs = &ls2k0500_pixpll_funcs;
+	} else {
+		drm_err(this->ddev, "unknown chip, the driver need update\n");
+		return -ENOENT;
+	}
+
+	return this->funcs->setup(this);
+}
diff --git a/drivers/gpu/drm/lsdc/lsdc_pll.h b/drivers/gpu/drm/lsdc/lsdc_pll.h
new file mode 100644
index 000000000000..538739f461f2
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_pll.h
@@ -0,0 +1,78 @@ 
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef __LSDC_PLL_H__
+#define __LSDC_PLL_H__
+
+#include <drm/drm_device.h>
+
+/*
+ * Loongson Pixel PLL hardware structure
+ *
+ * refclk: reference frequency, 100 MHz from external oscillator
+ * outclk: output frequency desired.
+ *
+ *
+ *               L1       Fref                      Fvco     L2
+ * refclk   +-----------+      +------------------+      +---------+   outclk
+ * ---+---> | Prescaler | ---> | Clock Multiplier | ---> | divider | -------->
+ *    |     +-----------+      +------------------+      +---------+     ^
+ *    |           ^                      ^                    ^          |
+ *    |           |                      |                    |          |
+ *    |           |                      |                    |          |
+ *    |        div_ref                 loopc               div_out       |
+ *    |                                                                  |
+ *    +--- sel_out (bypass above software configurable clock if set) ----+
+ *
+ *  sel_out: PLL clock output selector (for debug purpose only).
+ *
+ *  If sel_out == 1, it will take refclk as output directly,
+ *  the L1 Prescaler and the out divider will be bypassed.
+ *
+ *  If sel_out == 0, then outclk = refclk / div_ref * loopc / div_out;
+ *
+ * PLL working requirements:
+ *
+ *  1) 20 MHz <= refclk / div_ref <= 40Mhz
+ *  2) 1.2 GHz <= refclk /div_out * loopc <= 3.2 Ghz
+ */
+
+struct lsdc_pll_parms {
+	unsigned int div_ref;
+	unsigned int loopc;
+	unsigned int div_out;
+};
+
+struct lsdc_pll;
+
+struct lsdc_pixpll_funcs {
+	int (*setup)(struct lsdc_pll * const this);
+	bool (*compute)(struct lsdc_pll * const this,
+			unsigned int clock,
+			struct lsdc_pll_parms *pout);
+	int (*update)(struct lsdc_pll * const this,
+		      struct lsdc_pll_parms const *pin);
+	unsigned int (*get_clock_rate)(struct lsdc_pll * const this,
+				       struct lsdc_pll_parms *pout);
+};
+
+struct lsdc_pll {
+	const struct lsdc_pixpll_funcs *funcs;
+	struct drm_device *ddev;
+	void __iomem *mmio;
+
+	/* PLL register offset */
+	u32 reg_base;
+	/* PLL register size in bytes */
+	u32 reg_size;
+
+	/* 100000kHz, fixed on all board found */
+	unsigned int ref_clock;
+
+	unsigned int index;
+};
+
+int lsdc_pixpll_init(struct lsdc_pll * const this,
+		     struct drm_device *ddev,
+		     unsigned int index);
+
+#endif
diff --git a/drivers/gpu/drm/lsdc/lsdc_regs.c b/drivers/gpu/drm/lsdc/lsdc_regs.c
new file mode 100644
index 000000000000..c7950c43968f
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_regs.c
@@ -0,0 +1,29 @@ 
+// SPDX-License-Identifier: GPL-2.0
+
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+
+u32 lsdc_rreg32(struct lsdc_device * const ldev, u32 offset)
+{
+	unsigned long flags;
+	u32 ret;
+
+	spin_lock_irqsave(&ldev->reglock, flags);
+
+	ret = readl(ldev->reg_base + offset);
+
+	spin_unlock_irqrestore(&ldev->reglock, flags);
+
+	return ret;
+}
+
+void lsdc_wreg32(struct lsdc_device * const ldev, u32 offset, u32 val)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ldev->reglock, flags);
+
+	writel(val, ldev->reg_base + offset);
+
+	spin_unlock_irqrestore(&ldev->reglock, flags);
+}
diff --git a/drivers/gpu/drm/lsdc/lsdc_regs.h b/drivers/gpu/drm/lsdc/lsdc_regs.h
new file mode 100644
index 000000000000..b6aa6b706cc9
--- /dev/null
+++ b/drivers/gpu/drm/lsdc/lsdc_regs.h
@@ -0,0 +1,294 @@ 
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef __LSDC_REGS_H__
+#define __LSDC_REGS_H__
+
+#include <linux/bitops.h>
+#include <linux/types.h>
+
+/*
+ * PIXEL PLL Reference clock
+ */
+#define LSDC_PLL_REF_CLK                100000           /* kHz */
+
+/*
+ * Those PLL registers are not located at DC reg bar space,
+ * there are relative to LSXXXXX_CFG_REG_BASE.
+ * XXXXX = 7A1000, 2K1000, 2K0500
+ */
+
+/* LS2K1000 */
+#define LS2K1000_PIX_PLL0_REG           0x04B0
+#define LS2K1000_PIX_PLL1_REG           0x04C0
+#define LS2K1000_CFG_REG_BASE           0x1fe10000
+
+/* LS7A1000 and LS2K2000 */
+#define LS7A1000_PIX_PLL0_REG           0x04B0
+#define LS7A1000_PIX_PLL1_REG           0x04C0
+#define LS7A1000_CFG_REG_BASE           0x10010000
+
+/* LS2K0500 */
+#define LS2K0500_PIX_PLL0_REG           0x0418
+#define LS2K0500_PIX_PLL1_REG           0x0420
+#define LS2K0500_CFG_REG_BASE           0x1fe10000
+
+/*
+ *  CRTC CFG REG
+ */
+#define CFG_PIX_FMT_MASK                GENMASK(2, 0)
+
+enum lsdc_pixel_format {
+	LSDC_PF_NONE = 0,
+	LSDC_PF_ARGB4444 = 1,  /* ARGB A:4 bits R/G/B: 4 bits each [16 bits] */
+	LSDC_PF_ARGB1555 = 2,  /* ARGB A:1 bit RGB:15 bits [16 bits] */
+	LSDC_PF_RGB565 = 3,    /* RGB [16 bits] */
+	LSDC_PF_XRGB8888 = 4,  /* XRGB [32 bits] */
+	LSDC_PF_RGBA8888 = 5,  /* ARGB [32 bits] */
+};
+
+/* Each CRTC has two FB address registers, CFG_FB_IDX_BIT specify
+ * which fb address register is currently in using by the CRTC.
+ * Setting CFG_PAGE_FLIP_BIT bit will triger the switch. The switch
+ * finished at the vblank and if you want switch back you can set
+ * CFG_PAGE_FLIP_BIT again.
+ */
+#define CFG_PAGE_FLIP                   BIT(7)
+#define CFG_OUTPUT_EN                   BIT(8)
+/* CRTC0 clone from CRTC1 or CRTC1 clone from CRTC0 using hardware logic */
+#define CFG_PANEL_SWITCH                BIT(9)
+/* Indicate witch fb addr reg is in using, currently */
+#define CFG_FB_IN_USING                 BIT(11)
+#define CFG_GAMMA_EN                    BIT(12)
+
+/* CRTC get soft reset if voltage level change from 1 -> 0 */
+#define CFG_RESET_N                     BIT(20)
+
+#define CFG_HSYNC_EN                    BIT(30)
+#define CFG_HSYNC_INV                   BIT(31)
+#define CFG_VSYNC_EN                    BIT(30)
+#define CFG_VSYNC_INV                   BIT(31)
+
+/* THE DMA step of the DC in LS7A2000 is configurable */
+#define LSDC_DMA_STEP_MASK              GENMASK(17, 16)
+enum lsdc_dma_steps_supported {
+	LSDC_DMA_STEP_256_BYTES = 0,
+	LSDC_DMA_STEP_128_BYTES = 1,
+	LSDC_DMA_STEP_64_BYTES = 2,
+	LSDC_DMA_STEP_32_BYTES = 3,
+};
+
+/******** CRTC0 & DVO0 ********/
+#define LSDC_CRTC0_CFG_REG              0x1240
+#define LSDC_CRTC0_FB0_LO_ADDR_REG      0x1260
+#define LSDC_CRTC0_FB0_HI_ADDR_REG      0x15A0
+#define LSDC_CRTC0_FB1_LO_ADDR_REG      0x1580
+#define LSDC_CRTC0_FB1_HI_ADDR_REG      0x15C0
+#define LSDC_CRTC0_STRIDE_REG           0x1280
+#define LSDC_CRTC0_FB_ORIGIN_REG        0x1300
+#define LSDC_CRTC0_HDISPLAY_REG         0x1400
+#define LSDC_CRTC0_HSYNC_REG            0x1420
+#define LSDC_CRTC0_VDISPLAY_REG         0x1480
+#define LSDC_CRTC0_VSYNC_REG            0x14A0
+#define LSDC_CRTC0_GAMMA_INDEX_REG      0x14E0
+#define LSDC_CRTC0_GAMMA_DATA_REG       0x1500
+
+/******** CTRC1 & DVO1 ********/
+#define LSDC_CRTC1_CFG_REG              0x1250
+#define LSDC_CRTC1_FB0_LO_ADDR_REG      0x1270
+#define LSDC_CRTC1_FB0_HI_ADDR_REG      0x15B0
+#define LSDC_CRTC1_FB1_LO_ADDR_REG      0x1590
+#define LSDC_CRTC1_FB1_HI_ADDR_REG      0x15D0
+#define LSDC_CRTC1_STRIDE_REG           0x1290
+#define LSDC_CRTC1_FB_ORIGIN_REG        0x1310
+#define LSDC_CRTC1_HDISPLAY_REG         0x1410
+#define LSDC_CRTC1_HSYNC_REG            0x1430
+#define LSDC_CRTC1_VDISPLAY_REG         0x1490
+#define LSDC_CRTC1_VSYNC_REG            0x14B0
+#define LSDC_CRTC1_GAMMA_INDEX_REG      0x14F0
+#define LSDC_CRTC1_GAMMA_DATA_REG       0x1510
+
+/*
+ *  LS7A2000 has the hardware which record the scan position of the CRTC
+ */
+#define LSDC_CRTC0_SCAN_POS_REG         0x14C0
+#define LSDC_CRTC1_SCAN_POS_REG         0x14D0
+
+/*
+ *  LS7A2000 has the hardware which count the number of vblank generated
+ */
+#define LSDC_CRTC0_VSYNC_COUNTER_REG    0x1A00
+#define LSDC_CRTC1_VSYNC_COUNTER_REG    0x1A10
+
+/* In all, LSDC_CRTC1_XXX_REG - LSDC_CRTC0_XXX_REG = 0x10 */
+
+/*
+ * There is only one hardware cursor unit in ls7a1000, ls2k1000 and ls2k0500.
+ * well, ls7a2000 has two hardware cursor unit.
+ */
+#define CURSOR_FORMAT_MASK              GENMASK(1, 0)
+#define CURSOR_FORMAT_DISABLE           0
+#define CURSOR_FORMAT_MONOCHROME        1
+#define CURSOR_FORMAT_ARGB8888          2
+#define CURSOR_SIZE_64X64               BIT(2)
+#define CURSOR_LOCATION                 BIT(4)
+
+#define LSDC_CURSOR0_CFG_REG            0x1520
+#define LSDC_CURSOR0_ADDR_LO_REG        0x1530
+#define LSDC_CURSOR0_ADDR_HI_REG        0x15e0
+#define LSDC_CURSOR0_POSITION_REG       0x1540
+#define LSDC_CURSOR0_BG_COLOR_REG       0x1550  /* background color */
+#define LSDC_CURSOR0_FG_COLOR_REG       0x1560  /* foreground color */
+
+#define LSDC_CURSOR1_CFG_REG            0x1670
+#define LSDC_CURSOR1_ADDR_LO_REG        0x1680
+#define LSDC_CURSOR1_ADDR_HI_REG        0x16e0
+#define LSDC_CURSOR1_POSITION_REG       0x1690
+#define LSDC_CURSOR1_BG_COLOR_REG       0x16A0  /* background color */
+#define LSDC_CURSOR1_FG_COLOR_REG       0x16B0  /* foreground color */
+
+/*
+ * DC Interrupt Control Register, 32bit, Address Offset: 1570
+ *
+ * Bits  0:10 inidicate the interrupt type, read only
+ * Bits 26:16 control whether enable the interrupt corresponding to
+ * bit 10:0 or not. Write 1 to enable, write 0 to disable
+ *
+ * RF: Read Finished
+ * IDBU: Internal Data Buffer Underflow
+ * IDBFU: Internal Data Buffer Fatal Underflow
+ * CBRF: Cursor Buffer Read Finished Flag, no use.
+ *
+ * +-------+--------------------------+-------+--------+--------+-------+
+ * | 31:27 |         26:16            | 15:11 |   10   |   9    |   8   |
+ * +-------+--------------------------+-------+--------+--------+-------+
+ * |  N/A  | Interrupt Enable Control |  N/A  | IDBFU0 | IDBFU1 | IDBU0 |
+ * +-------+--------------------------+-------+--------+--------+-------+
+ *
+ * +-------+-----+-----+------+--------+--------+--------+--------+
+ * |   7   |  6  |  5  |  4   |   3    |   2    |   1    |   0    |
+ * +-------+-----+-----+------+--------+--------+--------+--------+
+ * | IDBU1 | RF0 | RF1 | CRRF | HSYNC0 | VSYNC0 | HSYNC1 | VSYNC1 |
+ * +-------+-----+-----+------+--------+--------+--------+--------+
+ */
+
+#define LSDC_INT_REG                           0x1570
+
+#define INT_CRTC0_VSYNC                        BIT(2)
+#define INT_CRTC0_HSYNC                        BIT(3)
+#define INT_CRTC0_RF                           BIT(6)
+#define INT_CRTC0_IDBU                         BIT(8)
+#define INT_CRTC0_IDBFU                        BIT(10)
+
+#define INT_CURSOR_RF                          BIT(4)
+
+#define INT_CRTC1_VSYNC                        BIT(0)
+#define INT_CRTC1_HSYNC                        BIT(1)
+#define INT_CRTC1_RF                           BIT(5)
+#define INT_CRTC1_IDBU                         BIT(7)
+#define INT_CRTC1_IDBFU                        BIT(9)
+
+#define INT_CRTC0_VS_EN                        BIT(18)
+#define INT_CRTC0_HS_EN                        BIT(19)
+#define INT_CRTC0_RF_EN                        BIT(22)
+#define INT_CRTC0_IDBU_EN                      BIT(24)
+#define INT_CRTC0_IDBFU_EN                     BIT(26)
+
+#define INT_CURSOR_RF_EN                       BIT(20)
+
+#define INT_CRTC1_VS_EN                        BIT(16)
+#define INT_CRTC1_HS_EN                        BIT(17)
+#define INT_CRTC1_RF_EN                        BIT(21)
+#define INT_CRTC1_IDBU_EN                      BIT(23)
+#define INT_CRTC1_IDBFU_EN                     BIT(25)
+
+#define INT_STATUS_MASK                        GENMASK(15, 0)
+
+/*
+ * LS7A1000 have 4 gpios which is under control of the LS7A_DC_GPIO_DAT_REG
+ * and LS7A_DC_GPIO_DIR_REG register, it has no relationship whth the general
+ * GPIO hardware. Those registers are in the DC register space on LS7A1000.
+ *
+ * Those GPIOs are used to emulated I2C, for reading edid and monitor detection
+ *
+ * LS2k1000 and LS2K0500 don't have those registers, they use hardware i2c or
+ * generial GPIO emulated i2c from other module.
+ *
+ * GPIO data register
+ *  Address offset: 0x1650
+ *   +---------------+-----------+-----------+
+ *   | 7 | 6 | 5 | 4 |  3  |  2  |  1  |  0  |
+ *   +---------------+-----------+-----------+
+ *   |               |    DVO1   |    DVO0   |
+ *   +      N/A      +-----------+-----------+
+ *   |               | SCL | SDA | SCL | SDA |
+ *   +---------------+-----------+-----------+
+ */
+#define LS7A_DC_GPIO_DAT_REG            0x1650
+
+/*
+ *  GPIO Input/Output direction control register
+ *  Address offset: 0x1660
+ */
+#define LS7A_DC_GPIO_DIR_REG            0x1660
+
+/*
+ *  LS7A2000 has two Built-in HDMI Encoder
+ */
+#define HDMI_INTERFACE_EN               BIT(0)
+#define HDMI_PACKET_EN                  BIT(1)
+#define HDMI_AUDIO_EN                   BIT(2)
+#define HDMI_VIDEO_PREAMBLE_MASK        GENMASK(7, 4)
+#define HDMI_HW_I2C_EN                  BIT(8)
+#define HDMI_CTL_PERIOD_MODE            BIT(9)
+
+/*
+ * Number of continuous packets may be present
+ * in HDMI hblank and vblank zone, should >= 48
+ */
+#define HDMI0_ZONE_REG                  0x1700
+#define HDMI1_ZONE_REG                  0x1710
+
+#define HDMI0_CTRL_REG                  0x1720
+#define HDMI1_CTRL_REG                  0x1730
+
+#define HDMI_PHY_EN                     BIT(0)
+#define HDMI_PHY_RESET_N                BIT(1)
+#define HDMI_PHY_TERM_L_EN              BIT(8)
+#define HDMI_PHY_TERM_H_EN              BIT(9)
+#define HDMI_PHY_TERM_DET_EN            BIT(10)
+#define HDMI_PHY_TERM_STATUS            BIT(11)
+
+#define HDMI0_PHY_CTRL_REG              0x1800
+#define HDMI1_PHY_CTRL_REG              0x1810
+
+/*
+ *  IDF: Input Division Factor
+ *  ODF: Output Division Factor
+ *   LF: Loop Factor
+ *    M: Required Mult
+ *
+ *  +--------------------------------------------------------+
+ *  |     Fin (kHZ)     | M  | IDF | LF | ODF |   Fout(Mhz)  |
+ *  |-------------------+----+-----+----+-----+--------------|
+ *  |  170000 ~ 340000  | 10 | 16  | 40 |  1  | 1700 ~ 3400  |
+ *  |   85000 ~ 170000  | 10 |  8  | 40 |  2  |  850 ~ 1700  |
+ *  |   42500 ~  85000  | 10 |  4  | 40 |  4  |  425 ~ 850   |
+ *  |   21250 ~  42500  | 10 |  2  | 40 |  8  | 212.5 ~ 425  |
+ *  |   20000 ~  21250  | 10 |  1  | 40 | 16  |  200 ~ 212.5 |
+ *  +--------------------------------------------------------+
+ */
+#define HDMI0_PHY_PLL_REG               0x1820
+#define HDMI1_PHY_PLL_REG               0x1830
+
+#define HDMI_PLL_ENABLE                 BIT(0)
+#define HDMI_PLL_LOCKED                 BIT(16)
+#define HDMI_PLL_BYPASS                 BIT(17)
+
+#define HDMI_PLL_IDF_SHIFT              1
+#define HDMI_PLL_IDF_MASK               GENMASK(5, 1)
+#define HDMI_PLL_LF_SHIFT               6
+#define HDMI_PLL_LF_MASK                GENMASK(12, 6)
+#define HDMI_PLL_ODF_SHIFT              13
+#define HDMI_PLL_ODF_MASK               GENMASK(15, 13)
+
+#endif