diff mbox series

[4/9] arm64: dts: qcom: sm8150-hdk: enable HDMI output

Message ID 20231209232132.3580045-5-dmitry.baryshkov@linaro.org (mailing list archive)
State New, archived
Headers show
Series arm64: dts: qcom: sm8150-hdk: enable display output | expand

Commit Message

Dmitry Baryshkov Dec. 9, 2023, 11:21 p.m. UTC 
Add DSI outputs and link them to the onboard Lontium LT9611 DSI-to-HDMI
bridge, enabling HDMI output on this board. While adding the display
resources, also drop the headless ("amd,imageon") compat string from the
GPU node, since the board now has output.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 128 +++++++++++++++++++++++-
 1 file changed, 123 insertions(+), 5 deletions(-)

Comments

Konrad Dybcio Dec. 11, 2023, 9:31 a.m. UTC | #1 
On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> Add DSI outputs and link them to the onboard Lontium LT9611 DSI-to-HDMI
> bridge, enabling HDMI output on this board. While adding the display
> resources, also drop the headless ("amd,imageon") compat string from the
> GPU node, since the board now has output.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
[...]


> +
> +	lt9611_irq_pin: lt9611-irq-state {
> +		pins = "gpio9";
> +		function = "gpio";
> +		bias-disable;
No drive-strength?

Otherwise lokos good at a glance!

Konrad
Dmitry Baryshkov Dec. 11, 2023, 9:45 a.m. UTC | #2 
On Mon, 11 Dec 2023 at 11:31, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>
> On 10.12.2023 00:21, Dmitry Baryshkov wrote:
> > Add DSI outputs and link them to the onboard Lontium LT9611 DSI-to-HDMI
> > bridge, enabling HDMI output on this board. While adding the display
> > resources, also drop the headless ("amd,imageon") compat string from the
> > GPU node, since the board now has output.
> >
> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> > ---
> [...]
>
>
> > +
> > +     lt9611_irq_pin: lt9611-irq-state {
> > +             pins = "gpio9";
> > +             function = "gpio";
> > +             bias-disable;
> No drive-strength?

For the input pin with no bias? I'm not sure. And yes, it was c&p from RB3.

> Otherwise lokos good at a glance!
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
index bb161b536da4..6a036f9ba1c9 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -54,6 +54,17 @@  key-vol-up {
 			gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
 };
 
 &apps_rsc {
@@ -359,12 +370,112 @@  &gmu {
 	status = "okay";
 };
 
+&gpi_dma1 {
+	status = "okay";
+};
+
 &gpu {
-	/*
-	 * NOTE: "amd,imageon" makes Adreno start in headless mode, remove it
-	 * after display support is added on this board.
-	 */
-	compatible = "qcom,adreno-640.1", "qcom,adreno", "amd,imageon";
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	lt9611_codec: hdmi-bridge@3b {
+		compatible = "lontium,lt9611";
+		reg = <0x3b>;
+		#sound-dai-cells = <1>;
+
+		interrupts-extended = <&tlmm 9 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&vreg_s4a_1p8>;
+		vcc-supply = <&vreg_bob>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_irq_pin>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lt9611_b: endpoint {
+					remote-endpoint = <&mdss_dsi1_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l3c_1p2>;
+
+	qcom,dual-dsi-mode;
+	qcom,master-dsi;
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_a>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vreg_l5a_0p875>;
+};
+
+&mdss_dsi1 {
+	vdda-supply = <&vreg_l3c_1p2>;
+
+	qcom,dual-dsi-mode;
+
+	/* DSI1 is slave, so use DSI0 clocks */
+	assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+	status = "okay";
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_b>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&mdss_dsi1_phy {
+	vdds-supply = <&vreg_l5a_0p875>;
 	status = "okay";
 };
 
@@ -402,6 +513,13 @@  &remoteproc_slpi {
 
 &tlmm {
 	gpio-reserved-ranges = <0 4>, <126 4>;
+
+	lt9611_irq_pin: lt9611-irq-state {
+		pins = "gpio9";
+		function = "gpio";
+		bias-disable;
+	};
+
 };
 
 &uart2 {