| Message ID | 20250212075845.11338-2-clamor95@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | mfd: lm3533: convert to use OF | expand |
On Wed, Feb 12, 2025 at 09:58:41AM +0200, Svyatoslav Ryhel wrote: > Add bindings for the LM3533 - a complete power source for > backlight, keypad, and indicator LEDs in smartphone handsets. > The high-voltage inductive boost converter provides the > power for two series LED strings display backlight and keypad > functions. > > Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> > --- > .../devicetree/bindings/mfd/ti,lm3533.yaml | 221 ++++++++++++++++++ > include/dt-bindings/mfd/lm3533.h | 19 ++ > 2 files changed, 240 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > create mode 100644 include/dt-bindings/mfd/lm3533.h > > diff --git a/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml b/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > new file mode 100644 > index 000000000000..d0307e5894f8 > --- /dev/null > +++ b/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > @@ -0,0 +1,221 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/mfd/ti,lm3533.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: TI LM3533 Complete Lighting Power Solution > + > +description: | > + The LM3533 is a complete power source for backlight, > + keypad, and indicator LEDs in smartphone handsets. The > + high-voltage inductive boost converter provides the > + power for two series LED strings display backlight and > + keypad functions. > + https://www.ti.com/product/LM3533 > + > +maintainers: > + - Johan Hovold <jhovold@gmail.com> > + > +properties: > + compatible: > + const: ti,lm3533 > + > + reg: > + maxItems: 1 > + > + '#address-cells': > + const: 1 > + > + '#size-cells': > + const: 0 > + > + enable-gpios: > + description: GPIO to use to enable/disable the backlight (HWEN pin). > + maxItems: 1 > + > + ti,boost-ovp: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Boost OVP select (16V, 24V, 32V, 40V) > + enum: [ 0, 1, 2, 3 ] > + default: 0 > + > + ti,boost-freq: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Boost frequency select (500KHz or 1MHz) > + enum: [ 0, 1 ] > + default: 0 Properties like these should be in units, so some standard voltage-based one for the boost and in hertz for the second. See property-units.yaml in dt-schema. > +required: > + - compatible > + - reg > + - '#address-cells' > + - '#size-cells' > + - enable-gpios > + > +patternProperties: > + "^backlight@[01]$": > + type: object > + description: > + Properties for a backlight device. > + > + properties: > + compatible: > + const: lm3533-backlight Missing vendor prefix > + > + reg: > + description: | > + The control bank that is used to program the two current sinks. The > + LM3533 has two control banks (A and B) and are represented as 0 or 1 > + in this property. The two current sinks can be controlled > + independently with both banks, or bank A can be configured to control > + both sinks with the led-sources property. > + minimum: 0 > + maximum: 1 > + > + max-current-microamp: > + description: > + Maximum current in µA with a 800 µA step. > + enum: [ 5000, 5800, 6600, 7400, 8200, 9000, 9800, > + 10600, 11400, 12200, 13000, 13800, 14600, > + 15400, 16200, 17000, 17800, 18600, 19400, > + 20200, 21000, 21800, 22600, 23400, 24200, > + 25000, 25800, 26600, 27400, 28200, 29000, > + 29800 ] > + default: 5000 > + > + default-brightness: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Default brightness level on boot. > + minimum: 0 > + maximum: 255 > + default: 255 > + > + pwm: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Default pwm level on boot. > + minimum: 0 > + maximum: 63 > + default: 0 Why is default-brightness /and/ a default for pwm needed? If the pwm drives the backlight, wouldn't you only need one of these two? If it stays, I think it needs a rename to be more clear about what it is doing. "pwm" is very close to "pwms", the property used for phandles to pwm providers but the use is rather different. backlight/common.yaml has standard properties that you could be using, so I'd expect to see a ref here, rather than redefining your own version. > + > + required: > + - compatible > + - reg > + > + additionalProperties: false > + > + "^led@[0-3]$": > + type: object > + description: > + Properties for a led device. > + > + properties: > + compatible: > + const: lm3533-leds Ditto here re: compatible. > + > + reg: > + description: > + 4 led banks > + minimum: 0 > + maximum: 3 > + > + max-current-microamp: > + description: > + Maximum current in µA with a 800 µA step. > + enum: [ 5000, 5800, 6600, 7400, 8200, 9000, 9800, > + 10600, 11400, 12200, 13000, 13800, 14600, > + 15400, 16200, 17000, 17800, 18600, 19400, > + 20200, 21000, 21800, 22600, 23400, 24200, > + 25000, 25800, 26600, 27400, 28200, 29000, > + 29800 ] > + default: 5000 > + > + default-trigger: > + $ref: /schemas/types.yaml#/definitions/string > + description: | > + This parameter, if present, is a string defining > + the trigger assigned to the LED. Check linux,default-trigger. > + > + pwm: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Default pwm level on boot. > + minimum: 0 > + maximum: 63 > + default: 0 Same applies here, leds/common.yaml has some of these already. > + > + required: > + - compatible > + - reg > + > + additionalProperties: false > + > + "^light-sensor@[0]$": Not a pattern if it can only have 1 outcome. > + type: object > + description: > + Properties for an illumination sensor. > + > + properties: > + compatible: > + const: lm3533-als > + > + reg: > + const: 0 > + > + resistor-value: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: | > + PWM resistor value a linear step in currents > + of 10 µA per code based upon 2V/R_ALS. > + minimum: 1 > + maximum: 127 > + default: 1 > + I'd expect a resistor to be measured in ohms of some sort, hard to tell what the increments actually are here, they don't appear to be a real unit. Are they register values? This and all other custom properties need to have a vendor prefix on them btw. > + pwm-mode: > + type: boolean > + description: Mode in which ALS is running Are there multiple pwm modes? Or is this trying to say that, if set, the sensor is in pwm mode? Hard to tell from the description here, sorry. Cheers, Conor. > + > + required: > + - compatible > + - reg > + > + additionalProperties: false > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + #include <dt-bindings/mfd/lm3533.h> > + > + i2c { > + #address-cells = <1>; > + #size-cells = <0>; > + > + led-controller@36 { > + compatible = "ti,lm3533"; > + reg = <0x36>; > + > + enable-gpios = <&gpio 110 GPIO_ACTIVE_HIGH>; > + > + ti,boost-ovp = <LM3533_BOOST_OVP_24V>; > + ti,boost-freq = <LM3533_BOOST_FREQ_500KHZ>; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + backlight@0 { > + compatible = "lm3533-backlight"; > + reg = <0>; > + > + max-current-microamp = <23400>; > + default-brightness = <113>; > + pwm = <0x00>; > + }; > + }; > + };
ср, 12 лют. 2025 р. о 21:49 Conor Dooley <conor@kernel.org> пише: > > On Wed, Feb 12, 2025 at 09:58:41AM +0200, Svyatoslav Ryhel wrote: > > Add bindings for the LM3533 - a complete power source for > > backlight, keypad, and indicator LEDs in smartphone handsets. > > The high-voltage inductive boost converter provides the > > power for two series LED strings display backlight and keypad > > functions. > > > > Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> > > --- > > .../devicetree/bindings/mfd/ti,lm3533.yaml | 221 ++++++++++++++++++ > > include/dt-bindings/mfd/lm3533.h | 19 ++ > > 2 files changed, 240 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > > create mode 100644 include/dt-bindings/mfd/lm3533.h > > > > diff --git a/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml b/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > > new file mode 100644 > > index 000000000000..d0307e5894f8 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > > @@ -0,0 +1,221 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/mfd/ti,lm3533.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: TI LM3533 Complete Lighting Power Solution > > + > > +description: | > > + The LM3533 is a complete power source for backlight, > > + keypad, and indicator LEDs in smartphone handsets. The > > + high-voltage inductive boost converter provides the > > + power for two series LED strings display backlight and > > + keypad functions. > > + https://www.ti.com/product/LM3533 > > + > > +maintainers: > > + - Johan Hovold <jhovold@gmail.com> > > + > > +properties: > > + compatible: > > + const: ti,lm3533 > > + > > + reg: > > + maxItems: 1 > > + > > + '#address-cells': > > + const: 1 > > + > > + '#size-cells': > > + const: 0 > > + > > + enable-gpios: > > + description: GPIO to use to enable/disable the backlight (HWEN pin). > > + maxItems: 1 > > + > > + ti,boost-ovp: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: > > + Boost OVP select (16V, 24V, 32V, 40V) > > + enum: [ 0, 1, 2, 3 ] > > + default: 0 > > + > > + ti,boost-freq: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: > > + Boost frequency select (500KHz or 1MHz) > > + enum: [ 0, 1 ] > > + default: 0 > > Properties like these should be in units, so some standard voltage-based > one for the boost and in hertz for the second. See property-units.yaml > in dt-schema. > > > +required: > > + - compatible > > + - reg > > + - '#address-cells' > > + - '#size-cells' > > + - enable-gpios > > + > > +patternProperties: > > + "^backlight@[01]$": > > + type: object > > + description: > > + Properties for a backlight device. > > + > > + properties: > > + compatible: > > + const: lm3533-backlight > > Missing vendor prefix > > > + > > + reg: > > + description: | > > + The control bank that is used to program the two current sinks. The > > + LM3533 has two control banks (A and B) and are represented as 0 or 1 > > + in this property. The two current sinks can be controlled > > + independently with both banks, or bank A can be configured to control > > + both sinks with the led-sources property. > > + minimum: 0 > > + maximum: 1 > > + > > + max-current-microamp: > > + description: > > + Maximum current in µA with a 800 µA step. > > + enum: [ 5000, 5800, 6600, 7400, 8200, 9000, 9800, > > + 10600, 11400, 12200, 13000, 13800, 14600, > > + 15400, 16200, 17000, 17800, 18600, 19400, > > + 20200, 21000, 21800, 22600, 23400, 24200, > > + 25000, 25800, 26600, 27400, 28200, 29000, > > + 29800 ] > > + default: 5000 > > + > > + default-brightness: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: > > + Default brightness level on boot. > > + minimum: 0 > > + maximum: 255 > > + default: 255 > > + > > + pwm: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: > > + Default pwm level on boot. > > + minimum: 0 > > + maximum: 63 > > + default: 0 > > Why is default-brightness /and/ a default for pwm needed? If the pwm > drives the backlight, wouldn't you only need one of these two? > > If it stays, I think it needs a rename to be more clear about what it is > doing. "pwm" is very close to "pwms", the property used for phandles to > pwm providers but the use is rather different. > > backlight/common.yaml has standard properties that you could be using, > so I'd expect to see a ref here, rather than redefining your own > version. > > > + > > + required: > > + - compatible > > + - reg > > + > > + additionalProperties: false > > + > > + "^led@[0-3]$": > > + type: object > > + description: > > + Properties for a led device. > > + > > + properties: > > + compatible: > > + const: lm3533-leds > > Ditto here re: compatible. > > > + > > + reg: > > + description: > > + 4 led banks > > + minimum: 0 > > + maximum: 3 > > + > > + max-current-microamp: > > + description: > > + Maximum current in µA with a 800 µA step. > > + enum: [ 5000, 5800, 6600, 7400, 8200, 9000, 9800, > > + 10600, 11400, 12200, 13000, 13800, 14600, > > + 15400, 16200, 17000, 17800, 18600, 19400, > > + 20200, 21000, 21800, 22600, 23400, 24200, > > + 25000, 25800, 26600, 27400, 28200, 29000, > > + 29800 ] > > + default: 5000 > > + > > + default-trigger: > > + $ref: /schemas/types.yaml#/definitions/string > > + description: | > > + This parameter, if present, is a string defining > > + the trigger assigned to the LED. Check linux,default-trigger. > > + > > + pwm: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: > > + Default pwm level on boot. > > + minimum: 0 > > + maximum: 63 > > + default: 0 > > Same applies here, leds/common.yaml has some of these already. > > > + > > + required: > > + - compatible > > + - reg > > + > > + additionalProperties: false > > + > > + "^light-sensor@[0]$": > > Not a pattern if it can only have 1 outcome. > > > + type: object > > + description: > > + Properties for an illumination sensor. > > + > > + properties: > > + compatible: > > + const: lm3533-als > > + > > + reg: > > + const: 0 > > + > > + resistor-value: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + description: | > > + PWM resistor value a linear step in currents > > + of 10 µA per code based upon 2V/R_ALS. > > + minimum: 1 > > + maximum: 127 > > + default: 1 > > + > > I'd expect a resistor to be measured in ohms of some sort, > hard to tell what the increments actually are here, they don't appear to > be a real unit. Are they register values? > > This and all other custom properties need to have a vendor prefix on > them btw. > > > + pwm-mode: > > + type: boolean > > + description: Mode in which ALS is running > > Are there multiple pwm modes? Or is this trying to say that, if set, the > sensor is in pwm mode? Hard to tell from the description here, sorry. > > Cheers, > Conor. > Acknowledged, thank you. > > > + > > + required: > > + - compatible > > + - reg > > + > > + additionalProperties: false > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/gpio/gpio.h> > > + #include <dt-bindings/mfd/lm3533.h> > > + > > + i2c { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + led-controller@36 { > > + compatible = "ti,lm3533"; > > + reg = <0x36>; > > + > > + enable-gpios = <&gpio 110 GPIO_ACTIVE_HIGH>; > > + > > + ti,boost-ovp = <LM3533_BOOST_OVP_24V>; > > + ti,boost-freq = <LM3533_BOOST_FREQ_500KHZ>; > > + > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + backlight@0 { > > + compatible = "lm3533-backlight"; > > + reg = <0>; > > + > > + max-current-microamp = <23400>; > > + default-brightness = <113>; > > + pwm = <0x00>; > > + }; > > + }; > > + }; >
On Wed, Feb 12, 2025 at 09:58:41AM +0200, Svyatoslav Ryhel wrote: > Add bindings for the LM3533 - a complete power source for > backlight, keypad, and indicator LEDs in smartphone handsets. > The high-voltage inductive boost converter provides the > power for two series LED strings display backlight and keypad > functions. > > Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> > --- > .../devicetree/bindings/mfd/ti,lm3533.yaml | 221 ++++++++++++++++++ > include/dt-bindings/mfd/lm3533.h | 19 ++ > 2 files changed, 240 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > create mode 100644 include/dt-bindings/mfd/lm3533.h > > diff --git a/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml b/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > new file mode 100644 > index 000000000000..d0307e5894f8 > --- /dev/null > +++ b/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > @@ -0,0 +1,221 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/mfd/ti,lm3533.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: TI LM3533 Complete Lighting Power Solution > + > +description: | > + The LM3533 is a complete power source for backlight, > + keypad, and indicator LEDs in smartphone handsets. The > + high-voltage inductive boost converter provides the > + power for two series LED strings display backlight and > + keypad functions. > + https://www.ti.com/product/LM3533 > + > +maintainers: > + - Johan Hovold <jhovold@gmail.com> This looks like it has been copied from the lm3533 driver. Did Johan agree to this? Daniel.
чт, 13 лют. 2025 р. о 23:32 Daniel Thompson <daniel@riscstar.com> пише: > > On Wed, Feb 12, 2025 at 09:58:41AM +0200, Svyatoslav Ryhel wrote: > > Add bindings for the LM3533 - a complete power source for > > backlight, keypad, and indicator LEDs in smartphone handsets. > > The high-voltage inductive boost converter provides the > > power for two series LED strings display backlight and keypad > > functions. > > > > Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> > > --- > > .../devicetree/bindings/mfd/ti,lm3533.yaml | 221 ++++++++++++++++++ > > include/dt-bindings/mfd/lm3533.h | 19 ++ > > 2 files changed, 240 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > > create mode 100644 include/dt-bindings/mfd/lm3533.h > > > > diff --git a/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml b/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > > new file mode 100644 > > index 000000000000..d0307e5894f8 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml > > @@ -0,0 +1,221 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/mfd/ti,lm3533.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: TI LM3533 Complete Lighting Power Solution > > + > > +description: | > > + The LM3533 is a complete power source for backlight, > > + keypad, and indicator LEDs in smartphone handsets. The > > + high-voltage inductive boost converter provides the > > + power for two series LED strings display backlight and > > + keypad functions. > > + https://www.ti.com/product/LM3533 > > + > > +maintainers: > > + - Johan Hovold <jhovold@gmail.com> > > This looks like it has been copied from the lm3533 driver. Did Johan > agree to this? > Thank you for pointing this out, maintainers field should have been amended with my name. It seems that this slipped from me on submitting. I initially though that maintainers should contain driver author hence set Johan, but that is obviously not correct. > > Daniel.
diff --git a/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml b/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml new file mode 100644 index 000000000000..d0307e5894f8 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ti,lm3533.yaml @@ -0,0 +1,221 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/ti,lm3533.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI LM3533 Complete Lighting Power Solution + +description: | + The LM3533 is a complete power source for backlight, + keypad, and indicator LEDs in smartphone handsets. The + high-voltage inductive boost converter provides the + power for two series LED strings display backlight and + keypad functions. + https://www.ti.com/product/LM3533 + +maintainers: + - Johan Hovold <jhovold@gmail.com> + +properties: + compatible: + const: ti,lm3533 + + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + enable-gpios: + description: GPIO to use to enable/disable the backlight (HWEN pin). + maxItems: 1 + + ti,boost-ovp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Boost OVP select (16V, 24V, 32V, 40V) + enum: [ 0, 1, 2, 3 ] + default: 0 + + ti,boost-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Boost frequency select (500KHz or 1MHz) + enum: [ 0, 1 ] + default: 0 + +required: + - compatible + - reg + - '#address-cells' + - '#size-cells' + - enable-gpios + +patternProperties: + "^backlight@[01]$": + type: object + description: + Properties for a backlight device. + + properties: + compatible: + const: lm3533-backlight + + reg: + description: | + The control bank that is used to program the two current sinks. The + LM3533 has two control banks (A and B) and are represented as 0 or 1 + in this property. The two current sinks can be controlled + independently with both banks, or bank A can be configured to control + both sinks with the led-sources property. + minimum: 0 + maximum: 1 + + max-current-microamp: + description: + Maximum current in µA with a 800 µA step. + enum: [ 5000, 5800, 6600, 7400, 8200, 9000, 9800, + 10600, 11400, 12200, 13000, 13800, 14600, + 15400, 16200, 17000, 17800, 18600, 19400, + 20200, 21000, 21800, 22600, 23400, 24200, + 25000, 25800, 26600, 27400, 28200, 29000, + 29800 ] + default: 5000 + + default-brightness: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Default brightness level on boot. + minimum: 0 + maximum: 255 + default: 255 + + pwm: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Default pwm level on boot. + minimum: 0 + maximum: 63 + default: 0 + + required: + - compatible + - reg + + additionalProperties: false + + "^led@[0-3]$": + type: object + description: + Properties for a led device. + + properties: + compatible: + const: lm3533-leds + + reg: + description: + 4 led banks + minimum: 0 + maximum: 3 + + max-current-microamp: + description: + Maximum current in µA with a 800 µA step. + enum: [ 5000, 5800, 6600, 7400, 8200, 9000, 9800, + 10600, 11400, 12200, 13000, 13800, 14600, + 15400, 16200, 17000, 17800, 18600, 19400, + 20200, 21000, 21800, 22600, 23400, 24200, + 25000, 25800, 26600, 27400, 28200, 29000, + 29800 ] + default: 5000 + + default-trigger: + $ref: /schemas/types.yaml#/definitions/string + description: | + This parameter, if present, is a string defining + the trigger assigned to the LED. Check linux,default-trigger. + + pwm: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Default pwm level on boot. + minimum: 0 + maximum: 63 + default: 0 + + required: + - compatible + - reg + + additionalProperties: false + + "^light-sensor@[0]$": + type: object + description: + Properties for an illumination sensor. + + properties: + compatible: + const: lm3533-als + + reg: + const: 0 + + resistor-value: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + PWM resistor value a linear step in currents + of 10 µA per code based upon 2V/R_ALS. + minimum: 1 + maximum: 127 + default: 1 + + pwm-mode: + type: boolean + description: Mode in which ALS is running + + required: + - compatible + - reg + + additionalProperties: false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/mfd/lm3533.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + led-controller@36 { + compatible = "ti,lm3533"; + reg = <0x36>; + + enable-gpios = <&gpio 110 GPIO_ACTIVE_HIGH>; + + ti,boost-ovp = <LM3533_BOOST_OVP_24V>; + ti,boost-freq = <LM3533_BOOST_FREQ_500KHZ>; + + #address-cells = <1>; + #size-cells = <0>; + + backlight@0 { + compatible = "lm3533-backlight"; + reg = <0>; + + max-current-microamp = <23400>; + default-brightness = <113>; + pwm = <0x00>; + }; + }; + }; +... diff --git a/include/dt-bindings/mfd/lm3533.h b/include/dt-bindings/mfd/lm3533.h new file mode 100644 index 000000000000..929988190c52 --- /dev/null +++ b/include/dt-bindings/mfd/lm3533.h @@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ +/* + * This header provides macros for TI LM3533 device bindings. + */ + +#ifndef _DT_BINDINGS_MFD_LM3533_H +#define _DT_BINDINGS_MFD_LM3533_H + +/* LM3533 boost freq */ +#define LM3533_BOOST_FREQ_500KHZ 0 +#define LM3533_BOOST_FREQ_1000KHZ 1 + +/* LM3533 boost ovp */ +#define LM3533_BOOST_OVP_16V 0 +#define LM3533_BOOST_OVP_24V 1 +#define LM3533_BOOST_OVP_32V 2 +#define LM3533_BOOST_OVP_40V 3 + +#endif
Add bindings for the LM3533 - a complete power source for backlight, keypad, and indicator LEDs in smartphone handsets. The high-voltage inductive boost converter provides the power for two series LED strings display backlight and keypad functions. Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> --- .../devicetree/bindings/mfd/ti,lm3533.yaml | 221 ++++++++++++++++++ include/dt-bindings/mfd/lm3533.h | 19 ++ 2 files changed, 240 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/ti,lm3533.yaml create mode 100644 include/dt-bindings/mfd/lm3533.h