deleted file mode 100644
@@ -1,52 +0,0 @@
-NXP Layerscape PCIe Gen4 controller
-
-This PCIe controller is based on the Mobiveil PCIe IP and thus inherits all
-the common properties defined in mobiveil-pcie.txt.
-
-Required properties:
-- compatible: should contain the platform identifier such as:
- "fsl,lx2160a-pcie"
-- reg: base addresses and lengths of the PCIe controller register blocks.
- "csr_axi_slave": Bridge config registers
- "config_axi_slave": PCIe controller registers
-- interrupts: A list of interrupt outputs of the controller. Must contain an
- entry for each entry in the interrupt-names property.
-- interrupt-names: It could include the following entries:
- "intr": The interrupt that is asserted for controller interrupts
- "aer": Asserted for aer interrupt when chip support the aer interrupt with
- none MSI/MSI-X/INTx mode,but there is interrupt line for aer.
- "pme": Asserted for pme interrupt when chip support the pme interrupt with
- none MSI/MSI-X/INTx mode,but there is interrupt line for pme.
-- dma-coherent: Indicates that the hardware IP block can ensure the coherency
- of the data transferred from/to the IP block. This can avoid the software
- cache flush/invalid actions, and improve the performance significantly.
-- msi-parent : See the generic MSI binding described in
- Documentation/devicetree/bindings/interrupt-controller/msi.txt.
-
-Example:
-
- pcie@3400000 {
- compatible = "fsl,lx2160a-pcie";
- reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
- 0x80 0x00000000 0x0 0x00001000>; /* configuration space */
- reg-names = "csr_axi_slave", "config_axi_slave";
- interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
- <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
- <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
- interrupt-names = "aer", "pme", "intr";
- #address-cells = <3>;
- #size-cells = <2>;
- device_type = "pci";
- apio-wins = <8>;
- ppio-wins = <8>;
- dma-coherent;
- bus-range = <0x0 0xff>;
- msi-parent = <&its>;
- ranges = <0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>;
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 7>;
- interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
- <0000 0 0 2 &gic 0 0 GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
- <0000 0 0 3 &gic 0 0 GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
- <0000 0 0 4 &gic 0 0 GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
- };
new file mode 100644
@@ -0,0 +1,173 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/mbvl,gpex40-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mobiveil AXI PCIe Root Port Bridge
+
+maintainers:
+ - Frank Li <Frank Li@nxp.com>
+
+description:
+ Mobiveil's GPEX 4.0 is a PCIe Gen4 root port bridge IP. This configurable IP
+ has up to 8 outbound and inbound windows for the address translation.
+
+ NXP Layerscape PCIe Gen4 controller (Deprecated) base on Mobiveil's GPEX 4.0.
+
+properties:
+ compatible:
+ enum:
+ - fsl,lx2160a-pcie
+ - mbvl,gpex40-pcie
+
+ reg:
+ items:
+ - description: PCIe controller registers
+ - description: Bridge config registers
+ - description: GPIO registers to control slot power
+ - description: MSI registers
+ minItems: 2
+
+ reg-names:
+ items:
+ - const: csr_axi_slave
+ - const: config_axi_slave
+ - const: gpio_slave
+ - const: apb_csr
+ minItems: 2
+
+ apio-wins:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ numbers of requested apio outbound windows
+ 1. Config window
+ 2. Memory window
+ default: 2
+ maximum: 256
+
+ ppio-wins:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: number of requested ppio inbound windows
+ default: 1
+ maximum: 256
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 1
+
+ interrupts:
+ minItems: 1
+ maxItems: 3
+
+ interrupt-names:
+ minItems: 1
+ maxItems: 3
+
+ dma-coherent: true
+
+ msi-parent: true
+
+required:
+ - compatible
+ - reg
+ - reg-names
+
+allOf:
+ - $ref: /schemas/pci/pci-host-bridge.yaml#
+ - if:
+ properties:
+ compatible:
+ enum:
+ - fsl,lx2160a-pcie
+ then:
+ properties:
+ reg:
+ maxItems: 2
+
+ reg-names:
+ maxItems: 2
+
+ interrupts:
+ minItems: 3
+
+ interrupt-names:
+ items:
+ - const: aer
+ - const: pme
+ - const: intr
+ else:
+ properties:
+ dma-coherent: false
+ msi-parent: false
+ interrupts:
+ maxItems: 1
+ interrupt-names: false
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ pcie@b0000000 {
+ compatible = "mbvl,gpex40-pcie";
+ reg = <0xb0000000 0x00010000>,
+ <0xa0000000 0x00001000>,
+ <0xff000000 0x00200000>,
+ <0xb0010000 0x00001000>;
+ reg-names = "csr_axi_slave",
+ "config_axi_slave",
+ "gpio_slave",
+ "apb_csr";
+ ranges = <0x83000000 0 0x00000000 0xa8000000 0 0x8000000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ apio-wins = <2>;
+ ppio-wins = <1>;
+ bus-range = <0x00000000 0x000000ff>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 0 &pci_express 0>,
+ <0 0 0 1 &pci_express 1>,
+ <0 0 0 2 &pci_express 2>,
+ <0 0 0 3 &pci_express 3>;
+ };
+
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ pcie@3400000 {
+ compatible = "fsl,lx2160a-pcie";
+ reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
+ 0x80 0x00000000 0x0 0x00001000>; /* configuration space */
+ reg-names = "csr_axi_slave", "config_axi_slave";
+ ranges = <0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
+ <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+ <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+ interrupt-names = "aer", "pme", "intr";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ apio-wins = <8>;
+ ppio-wins = <8>;
+ dma-coherent;
+ bus-range = <0x0 0xff>;
+ msi-parent = <&its>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 2 &gic 0 0 GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 3 &gic 0 0 GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 4 &gic 0 0 GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
deleted file mode 100644
@@ -1,72 +0,0 @@
-* Mobiveil AXI PCIe Root Port Bridge DT description
-
-Mobiveil's GPEX 4.0 is a PCIe Gen4 root port bridge IP. This configurable IP
-has up to 8 outbound and inbound windows for the address translation.
-
-Required properties:
-- #address-cells: Address representation for root ports, set to <3>
-- #size-cells: Size representation for root ports, set to <2>
-- #interrupt-cells: specifies the number of cells needed to encode an
- interrupt source. The value must be 1.
-- compatible: Should contain "mbvl,gpex40-pcie"
-- reg: Should contain PCIe registers location and length
- Mandatory:
- "config_axi_slave": PCIe controller registers
- "csr_axi_slave" : Bridge config registers
- Optional:
- "gpio_slave" : GPIO registers to control slot power
- "apb_csr" : MSI registers
-
-- device_type: must be "pci"
-- apio-wins : number of requested apio outbound windows
- default 2 outbound windows are configured -
- 1. Config window
- 2. Memory window
-- ppio-wins : number of requested ppio inbound windows
- default 1 inbound memory window is configured.
-- bus-range: PCI bus numbers covered
-- interrupt-controller: identifies the node as an interrupt controller
-- #interrupt-cells: specifies the number of cells needed to encode an
- interrupt source. The value must be 1.
-- interrupts: The interrupt line of the PCIe controller
- last cell of this field is set to 4 to
- denote it as IRQ_TYPE_LEVEL_HIGH type interrupt.
-- interrupt-map-mask,
- interrupt-map: standard PCI properties to define the mapping of the
- PCI interface to interrupt numbers.
-- ranges: ranges for the PCI memory regions (I/O space region is not
- supported by hardware)
- Please refer to the standard PCI bus binding document for a more
- detailed explanation
-
-
-Example:
-++++++++
- pcie0: pcie@a0000000 {
- #address-cells = <3>;
- #size-cells = <2>;
- compatible = "mbvl,gpex40-pcie";
- reg = <0xa0000000 0x00001000>,
- <0xb0000000 0x00010000>,
- <0xff000000 0x00200000>,
- <0xb0010000 0x00001000>;
- reg-names = "config_axi_slave",
- "csr_axi_slave",
- "gpio_slave",
- "apb_csr";
- device_type = "pci";
- apio-wins = <2>;
- ppio-wins = <1>;
- bus-range = <0x00000000 0x000000ff>;
- interrupt-controller;
- interrupt-parent = <&gic>;
- #interrupt-cells = <1>;
- interrupts = < 0 89 4 >;
- interrupt-map-mask = <0 0 0 7>;
- interrupt-map = <0 0 0 0 &pci_express 0>,
- <0 0 0 1 &pci_express 1>,
- <0 0 0 2 &pci_express 2>,
- <0 0 0 3 &pci_express 3>;
- ranges = < 0x83000000 0 0x00000000 0xa8000000 0 0x8000000>;
-
- };
@@ -17901,7 +17901,7 @@ M: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
M: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
L: linux-pci@vger.kernel.org
S: Supported
-F: Documentation/devicetree/bindings/pci/mobiveil-pcie.txt
+F: Documentation/devicetree/bindings/pci/mbvl,gpex40-pcie.yaml
F: drivers/pci/controller/mobiveil/pcie-mobiveil*
PCI DRIVER FOR MVEBU (Marvell Armada 370 and Armada XP SOC support)
@@ -17925,7 +17925,6 @@ M: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
L: linux-pci@vger.kernel.org
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
-F: Documentation/devicetree/bindings/pci/layerscape-pcie-gen4.txt
F: drivers/pci/controller/mobiveil/pcie-layerscape-gen4.c
PCI DRIVER FOR PLDA PCIE IP