@@ -32,6 +32,501 @@ port, and deploy the SM on supported processors.
The SM implements an interface compliant with the Arm SCMI Specification
with additional vendor specific extensions.
+SCMI_LMM: System Control and Management Logical Machine Management Vendor Protocol
+==================================================================================
+
+This protocol is intended for boot, shutdown, and reset of other logical
+machines (LM). It is usually used to allow one LM(e.g. OSPM) to manage
+another LM which is usually an offload or accelerator engine.. Notifications
+from this protocol can also be used to manage a communication link to another
+LM. The LMM protocol provides functions to:
+
+- Describe the protocol version.
+- Discover implementation attributes.
+- Discover the LMs defined in the system.
+- Boot an LM.
+- Shutdown an LM (gracefully or forcibly).
+- Reset an LM (gracefully or forcibly).
+- Wake an LM from suspend.
+- Suspend an LM (gracefully).
+- Read boot/shutdown/reset information for an LM.
+- Get notifications when an LM boots or shuts down (e.g. LM[X] requested
+ notification of LM[Y] boots or shuts down, when LM[Y] boots or shuts down,
+ SCMI firmware will send notification to LM[X]).
+
+'Graceful' means asking LM itself to shutdown/reset/etc (e.g. sending
+notification to Linux, Then Linux reboots or powers down itself). It is async
+command that the SUCCESS of the command just means the command successfully
+return, not means reboot/reset successfully finished.
+'Forceful' means the SM will force shutdown/reset/etc the LM. It is sync
+command that the SUCCESS of the command means the LM has been successfully
+shutdown/reset/etc.
+If the commands not have Graceful/Forceful flag settings, such as WAKE, SUSEND,
+it is async command.
+
+Commands:
+_________
+
+PROTOCOL_VERSION
+~~~~~~~~~~~~~~~~
+
+message_id: 0x0
+protocol_id: 0x80
+This command is mandatory.
+
++---------------+--------------------------------------------------------------+
+|Return values |
++---------------+--------------------------------------------------------------+
+|Name |Description |
++---------------+--------------------------------------------------------------+
+|int32 status | See ARM SCMI Specification for status code definitions. |
++---------------+--------------------------------------------------------------+
+|uint32 version | For this revision of the specification, this value must be |
+| | 0x10000. |
++---------------+--------------------------------------------------------------+
+
+PROTOCOL_ATTRIBUTES
+~~~~~~~~~~~~~~~~~~~
+
+message_id: 0x1
+protocol_id: 0x80
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status | See ARM SCMI Specification for status code definitions. |
++------------------+-----------------------------------------------------------+
+|uint32 attributes |Protocol attributes: |
+| |Bits[31:8] Reserved, must be zero. |
+| |Bits[7:0] Number of Logical Machines |
++------------------+-----------------------------------------------------------+
+
+PROTOCOL_MESSAGE_ATTRIBUTES
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+message_id: 0x2
+protocol_id: 0x80
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: in case the message is implemented and available |
+| |to use. |
+| |NOT_FOUND: if the message identified by message_id is |
+| |invalid or not implemented |
++------------------+-----------------------------------------------------------+
+|uint32 attributes |Flags that are associated with a specific function in the |
+| |protocol. For all functions in this protocol, this |
+| |parameter has a value of 0 |
++------------------+-----------------------------------------------------------+
+
+LMM_ATTRIBUTES
+~~~~~~~~~~~~~~
+
+message_id: 0x3
+protocol_id: 0x80
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 lmid |ID of the Logical Machine |
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: if valid attributes are returned. |
+| |NOT_FOUND: if lmId not points to a valid logical machine. |
+| |DENIED: if the agent does not have permission to get info |
+| |for the LM specified by lmid. |
++------------------+-----------------------------------------------------------+
+|uint32 lmid |Identifier of the LM whose identification is requested. |
+| |This field is: Populated with the lmId of the calling |
+| |agent, when the lmId parameter passed via the function is |
+| |0xFFFFFFFF. Identical to the lmId field passed via the |
+| |calling parameters, in all other cases |
++------------------+-----------------------------------------------------------+
+|uint32 attributes | Bits[31:0] reserved. must be zero |
++------------------+-----------------------------------------------------------+
+|uint32 state | Current state of the LM |
++------------------+-----------------------------------------------------------+
+|uint32 errStatus | Last error status recorded |
++------------------+-----------------------------------------------------------+
+|char name[16] | A NULL terminated ASCII string with the LM name, of up |
+| | to 16 bytes |
++------------------+-----------------------------------------------------------+
+
+LMM_BOOT
+~~~~~~~~
+
+message_id: 0x4
+protocol_id: 0x80
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 lmid |ID of the Logical Machine |
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: if LM boots successfully started. |
+| |NOT_FOUND: if lmId not points to a valid logical machine. |
+| |INVALID_PARAMETERS: if lmId is same as the caller. |
+| |DENIED: if the agent does not have permission to manage the|
+| |the LM specified by lmid. |
++------------------+-----------------------------------------------------------+
+
+LMM_RESET
+~~~~~~~~~
+
+message_id: 0x5
+protocol_id: 0x80
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 lmid |ID of the Logical Machine |
++------------------+-----------------------------------------------------------+
+|uint32 flags |Reset flags: |
+| |Bits[31:1] Reserved, must be zero. |
+| |Bit[0] Graceful request: |
+| |Set to 1 if the request is a graceful request. |
+| |Set to 0 if the request is a forceful request. |
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: The LMM RESET command finished successfully in |
+| |graceful reset or LM successfully resets in forceful reset.|
+| |NOT_FOUND: if lmId not points to a valid logical machine. |
+| |INVALID_PARAMETERS: if lmId is same as the caller. |
+| |DENIED: if the agent does not have permission to manage the|
+| |the LM specified by lmid. |
++------------------+-----------------------------------------------------------+
+
+LMM_SHUTDOWN
+~~~~~~~~~~~~
+
+message_id: 0x6
+protocol_id: 0x80
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 lmid |ID of the Logical Machine |
++------------------+-----------------------------------------------------------+
+|uint32 flags |Reset flags: |
+| |Bits[31:1] Reserved, must be zero. |
+| |Bit[0] Graceful request: |
+| |Set to 1 if the request is a graceful request. |
+| |Set to 0 if the request is a forceful request. |
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: The LMM shutdown command finished successfully in |
+| |graceful request or LM successfully shutdown in forceful |
+| |request. |
+| |NOT_FOUND: if lmId not points to a valid logical machine. |
+| |INVALID_PARAMETERS: if lmId is same as the caller. |
+| |DENIED: if the agent does not have permission to manage the|
+| |the LM specified by lmid. |
++------------------+-----------------------------------------------------------+
+
+LMM_WAKE
+~~~~~~~~
+
+message_id: 0x7
+protocol_id: 0x80
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 lmid |ID of the Logical Machine |
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: if LM wake command successfully returns. |
+| |NOT_FOUND: if lmId not points to a valid logical machine. |
+| |INVALID_PARAMETERS: if lmId is same as the caller. |
+| |DENIED: if the agent does not have permission to manage the|
+| |the LM specified by lmid. |
++------------------+-----------------------------------------------------------+
+
+LMM_SUSPEND
+~~~~~~~~~~~
+
+message_id: 0x8
+protocol_id: 0x80
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 lmid |ID of the Logical Machine |
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: if LM suspend command successfully returns. |
+| |NOT_FOUND: if lmId not points to a valid logical machine. |
+| |INVALID_PARAMETERS: if lmId is same as the caller. |
+| |DENIED: if the agent does not have permission to manage the|
+| |the LM specified by lmid. |
++------------------+-----------------------------------------------------------+
+
+LMM_NOTIFY
+~~~~~~~~~~
+
+message_id: 0x9
+protocol_id: 0x80
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 lmid |ID of the Logical Machine |
++------------------+-----------------------------------------------------------+
+|uint32 flags |Notification flags: |
+| |Bits[31:3] Reserved, must be zero. |
+| |Bit[3] Wake (resume) notification: |
+| |Set to 1 to send notification. |
+| |Set to 0 if no notification. |
+| |Bit[2] Suspend (sleep) notification: |
+| |Set to 1 to send notification. |
+| |Set to 0 if no notification. |
+| |Bit[1] Shutdown (off) notification: |
+| |Set to 1 to send notification. |
+| |Set to 0 if no notification. |
+| |Bit[0] Boot (on) notification: |
+| |Set to 1 to send notification. |
+| |Set to 0 if no notification |
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: if the notification state successfully updated. |
+| |NOT_FOUND: if lmId not points to a valid logical machine. |
+| |INVALID_PARAMETERS: if input attributes flag specifies |
+| |unsupported or invalid configurations. |
+| |DENIED: if the agent does not have permission to request |
+| |the notification. |
++------------------+-----------------------------------------------------------+
+
+LMM_RESET_REASON
+~~~~~~~~~~~~~~~~
+
+message_id: 0xA
+protocol_id: 0x80
+This command is mandatory.
+
+This command is to return the reset reason that caused the last reset, such as
+POR, WDOG, JTAG and etc.
+
++---------------------+--------------------------------------------------------+
+|Parameters |
++---------------------+--------------------------------------------------------+
+|Name |Description |
++---------------------+--------------------------------------------------------+
+|uint32 lmid |ID of the Logical Machine |
++---------------------+--------------------------------------------------------+
+|Return values |
++---------------------+--------------------------------------------------------+
+|Name |Description |
++---------------------+--------------------------------------------------------+
+|int32 status |SUCCESS: if the reset reason of the LM successfully |
+| |updated. |
+| |NOT_FOUND: if lmId not points to a valid logical machine|
+| |DENIED: if the agent does not have permission to request|
+| |the reset reason. |
++---------------------+--------------------------------------------------------+
+|uint32 bootflags |Boot reason flags. This parameter has the format: |
+| |Bits[31] Valid. |
+| |Set to 1 if the entire reason is valid. |
+| |Set to 0 if the entire reason is not valid. |
+| |Bits[30:29] Reserved, must be zero. |
+| |Bit[28] Valid origin: |
+| |Set to 1 if the origin field is valid. |
+| |Set to 0 if the origin field is not valid. |
+| |Bits[27:24] Origin. |
+| |Logical Machine(LM) ID that causes the BOOT of this LM |
+| |Bit[23] Valid err ID: |
+| |Set to 1 if the error ID field is valid. |
+| |Set to 0 if the error ID field is not valid. |
+| |Bits[22:8] Error ID(Agent ID of the system). |
+| |Bit[7:0] Reason(WDOG, POR, FCCU and etc) |
++---------------------+--------------------------------------------------------+
+|uint32 shutdownflags |Shutdown reason flags. This parameter has the format: |
+| |Bits[31] Valid. |
+| |Set to 1 if the entire reason is valid. |
+| |Set to 0 if the entire reason is not valid. |
+| |Bits[30:29] Number of valid extended info words. |
+| |Bit[28] Valid origin: |
+| |Set to 1 if the origin field is valid. |
+| |Set to 0 if the origin field is not valid. |
+| |Bits[27:24] Origin. |
+| |Logical Machine(LM) ID that causes the BOOT of this LM |
+| |Bit[23] Valid err ID: |
+| |Set to 1 if the error ID field is valid. |
+| |Set to 0 if the error ID field is not valid. |
+| |Bits[22:8] Error ID(Agent ID of the System). |
+| |Bit[7:0] Reason |
++---------------------+--------------------------------------------------------+
+|uint32 extinfo[3] |Array of extended info words(e.g. fault pc) |
++---------------------+--------------------------------------------------------+
+
+LMM_POWER_ON
+~~~~~~~~~~~~
+
+message_id: 0xB
+protocol_id: 0x80
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 lmid |ID of the Logical Machine |
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: if LM successfully powers on. |
+| |NOT_FOUND: if lmId not points to a valid logical machine. |
+| |INVALID_PARAMETERS: if lmId is same as the caller. |
+| |DENIED: if the agent does not have permission to manage the|
+| |the LM specified by lmid. |
++------------------+-----------------------------------------------------------+
+
+LMM_RESET_VECTOR_SET
+~~~~~~~~~~~~~~~~~~~~
+
+message_id: 0xC
+protocol_id: 0x80
+This command is mandatory.
+
++-----------------------+------------------------------------------------------+
+|Parameters |
++-----------------------+------------------------------------------------------+
+|Name |Description |
++-----------------------+------------------------------------------------------+
+|uint32 lmid |ID of the Logical Machine |
++-----------------------+------------------------------------------------------+
+|uint32 cpuid |ID of the CPU inside the LM |
++-----------------------+------------------------------------------------------+
+|uint32 flags |Reset vector flags |
+| |Bits[31:0] Reserved, must be zero. |
++-----------------------+------------------------------------------------------+
+|uint32 resetVectorLow |Lower vector |
++-----------------------+------------------------------------------------------+
+|uint32 resetVectorHigh |Higher vector |
++-----------------------+------------------------------------------------------+
+|Return values |
++-----------------------+------------------------------------------------------+
+|Name |Description |
++-----------------------+------------------------------------------------------+
+|int32 status |SUCCESS: If reset vector is set successfully. |
+| |NOT_FOUND: if lmId not points to a valid logical |
+| |machine, or cpuId is not valid. |
+| |INVALID_PARAMETERS: if reset vector is invalid. |
+| |DENIED: if the agent does not have permission to set |
+| |the reset vector for the CPU in the LM. |
++-----------------------+------------------------------------------------------+
+
+NEGOTIATE_PROTOCOL_VERSION
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+message_id: 0x10
+protocol_id: 0x80
+This command is mandatory.
+
++--------------------+---------------------------------------------------------+
+|Parameters |
++--------------------+---------------------------------------------------------+
+|Name |Description |
++--------------------+---------------------------------------------------------+
+|uint32 version |The negotiated protocol version the agent intends to use |
++--------------------+---------------------------------------------------------+
+|Return values |
++--------------------+---------------------------------------------------------+
+|Name |Description |
++--------------------+---------------------------------------------------------+
+|int32 status |SUCCESS: if the negotiated protocol version is supported |
+| |by the platform. All commands, responses, and |
+| |notifications post successful return of this command must|
+| |comply with the negotiated version. |
+| |NOT_SUPPORTED: if the protocol version is not supported. |
++--------------------+---------------------------------------------------------+
+
+Notifications
+_____________
+
+LMM_EVENT
+~~~~~~~~~
+
+message_id: 0x0
+protocol_id: 0x80
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 lmid |Identifier for the LM that caused the transition. |
++------------------+-----------------------------------------------------------+
+|uint32 eventlm |Identifier of the LM this event refers to. |
++------------------+-----------------------------------------------------------+
+|uint32 flags |LM events: |
+| |Bits[31:3] Reserved, must be zero. |
+| |Bit[3] Wake (resume) event: |
+| |1 LM has awakened. |
+| |0 not a wake event. |
+| |Bit[2] Suspend (sleep) event: |
+| |1 LM has suspended. |
+| |0 not a suspend event. |
+| |Bit[1] Shutdown (off) event: |
+| |1 LM has shutdown. |
+| |0 not a shutdown event. |
+| |Bit[0] Boot (on) event: |
+| |1 LM has booted. |
+| |0 not a boot event. |
++------------------+-----------------------------------------------------------+
+
SCMI_BBM: System Control and Management BBM Vendor Protocol
==============================================================
@@ -436,6 +931,312 @@ protocol_id: 0x81
| |0 no button change detected. |
+------------------+-----------------------------------------------------------+
+SCMI_CPU: System Control and Management CPU Vendor Protocol
+==============================================================
+
+This protocol allows an agent to start or stop a CPU. It is used to manage
+auxiliary CPUs in an LM (e.g. additional cores in an AP cluster or
+Cortex-M cores).
+Note:
+ - For cores in AP cluster, PSCI should be used and ATF will use CPU
+ protocol to handle them. For cores in non-AP cluster, Operating System(e.g.
+ Linux OS) could use CPU protocols to control Cortex-M7 cores.
+ - CPU indicates the core and its auxiliary peripherals(e.g. TCM) inside
+ i.MX SoC
+
+The CPU protocol provides functions to:
+
+- Describe the protocol version.
+- Discover implementation attributes.
+- Discover the CPUs defined in the system.
+- Start a CPU.
+- Stop a CPU.
+- Set the boot and resume addresses for a CPU.
+- Set the sleep mode of a CPU.
+- Configure wake-up sources for a CPU.
+- Configure power domain reactions (LPM mode and retention mask) for a CPU.
+- The CPU IDs can be found in the CPU section of the SoC DEVICE: SM Device
+ Interface. They can also be found in the SoC RM. See the CPU Mode Control
+ (CMC) list in General Power Controller (GPC) section.
+
+CPU settings are not aggregated and setting their state is normally exclusive
+to one client.
+
+Commands:
+_________
+
+PROTOCOL_VERSION
+~~~~~~~~~~~~~~~~
+
+message_id: 0x0
+protocol_id: 0x82
+This command is mandatory.
+
++---------------+--------------------------------------------------------------+
+|Return values |
++---------------+--------------------------------------------------------------+
+|Name |Description |
++---------------+--------------------------------------------------------------+
+|int32 status | See ARM SCMI Specification for status code definitions. |
++---------------+--------------------------------------------------------------+
+|uint32 version | For this revision of the specification, this value must be |
+| | 0x10000. |
++---------------+--------------------------------------------------------------+
+
+PROTOCOL_ATTRIBUTES
+~~~~~~~~~~~~~~~~~~~
+
+message_id: 0x1
+protocol_id: 0x82
+This command is mandatory.
+
++---------------+--------------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status | See ARM SCMI Specification for status code definitions. |
++------------------+-----------------------------------------------------------+
+|uint32 attributes |Protocol attributes: |
+| |Bits[31:16] Reserved, must be zero. |
+| |Bits[15:0] Number of CPUs |
++------------------+-----------------------------------------------------------+
+
+PROTOCOL_MESSAGE_ATTRIBUTES
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+message_id: 0x2
+protocol_id: 0x82
+This command is mandatory.
+
++---------------+--------------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: in case the message is implemented and available |
+| |to use. |
+| |NOT_FOUND: if the message identified by message_id is |
+| |invalid or not implemented |
++------------------+-----------------------------------------------------------+
+|uint32 attributes |Flags that are associated with a specific function in the |
+| |protocol. For all functions in this protocol, this |
+| |parameter has a value of 0 |
++------------------+-----------------------------------------------------------+
+
+CPU_ATTRIBUTES
+~~~~~~~~~~~~~~
+
+message_id: 0x4
+protocol_id: 0x82
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 cpuid |Identifier for the CPU |
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: if valid attributes are returned successfully. |
+| |NOT_FOUND: if the cpuid is not valid. |
++------------------+-----------------------------------------------------------+
+|uint32 attributes |Bits[31:0] Reserved, must be zero |
++------------------+-----------------------------------------------------------+
+|char name[16] |NULL terminated ASCII string with CPU name up to 16 bytes |
++------------------+-----------------------------------------------------------+
+
+CPU_START
+~~~~~~~~~
+
+message_id: 0x4
+protocol_id: 0x82
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 cpuid |Identifier for the CPU |
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: if the cpu is started successfully. |
+| |NOT_FOUND: if cpuid is not valid. |
+| |DENIED: the calling agent is not allowed to start this CPU.|
++------------------+-----------------------------------------------------------+
+
+CPU_STOP
+~~~~~~~~
+
+message_id: 0x5
+protocol_id: 0x82
+This command is mandatory.
+
++------------------+-----------------------------------------------------------+
+|Parameters |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|uint32 cpuid |Identifier for the CPU |
++------------------+-----------------------------------------------------------+
+|Return values |
++------------------+-----------------------------------------------------------+
+|Name |Description |
++------------------+-----------------------------------------------------------+
+|int32 status |SUCCESS: if the cpu is started successfully. |
+| |NOT_FOUND: if cpuid is not valid. |
+| |DENIED: the calling agent is not allowed to stop this CPU. |
++------------------+-----------------------------------------------------------+
+
+CPU_RESET_VECTOR_SET
+~~~~~~~~~~~~~~~~~~~~
+
+message_id: 0x6
+protocol_id: 0x82
+This command is mandatory.
+
++----------------------+-------------------------------------------------------+
+|Parameters |
++----------------------+-------------------------------------------------------+
+|Name |Description |
++----------------------+-------------------------------------------------------+
+|uint32 cpuid |Identifier for the CPU |
++----------------------+-------------------------------------------------------+
+|uint32 flags |Reset vector flags: |
+| |Bit[31] Resume flag. |
+| |Set to 1 to update the reset vector used on resume. |
+| |Bit[30] Boot flag. |
+| |Set to 1 to update the reset vector used for boot. |
+| |Bits[29:1] Reserved, must be zero. |
+| |Bit[0] Table flag. |
+| |Set to 1 if vector is the vector table base address. |
++----------------------+-------------------------------------------------------+
+|uint32 resetVectorLow |Lower vector: |
+| |If bit[0] of flags is 0, the lower 32 bits of the |
+| |physical address where the CPU should execute from on |
+| |reset. If bit[0] of flags is 1, the lower 32 bits of |
+| |the vector table base address |
++----------------------+-------------------------------------------------------+
+|uint32 resetVectorhigh|Upper vector: |
+| |If bit[0] of flags is 0, the upper 32 bits of the |
+| |physical address where the CPU should execute from on |
+| |reset. If bit[0] of flags is 1, the upper 32 bits of |
+| |the vector table base address |
++----------------------+-------------------------------------------------------+
+|Return values |
++----------------------+-------------------------------------------------------+
+|Name |Description |
++----------------------+-------------------------------------------------------+
+|int32 status |SUCCESS: if the CPU reset vector is set successfully. |
+| |NOT_FOUND: if cpuId does not point to a valid CPU. |
+| |INVALID_PARAMETERS: the requested vector type is not |
+| |supported by this CPU. |
+| |DENIED: the calling agent is not allowed to set the |
+| |reset vector of this CPU |
++----------------------+-------------------------------------------------------+
+
+CPU_SLEEP_MODE_SET
+~~~~~~~~~~~~~~~~~~
+
+message_id: 0x7
+protocol_id: 0x82
+This command is mandatory.
+
++----------------------+-------------------------------------------------------+
+|Parameters |
++----------------------+-------------------------------------------------------+
+|Name |Description |
++----------------------+-------------------------------------------------------+
+|uint32 cpuid |Identifier for the CPU |
++----------------------+-------------------------------------------------------+
+|uint32 flags |Sleep mode flags: |
+| |Bits[31:1] Reserved, must be zero. |
+| |Bit[0] IRQ mux: |
+| |If set to 1 the wakeup mux source is the GIC, else if 0|
+| |then the GPC |
++----------------------+-------------------------------------------------------+
+|uint32 sleepmode |target sleep mode. When CPU runs into WFI, the GPC mode|
+| |will be triggered to be in below modes: |
+| |RUN(0), WAIT(1), STOP(2), SUSPEND(3) |
++----------------------+-------------------------------------------------------+
+|Return values |
++----------------------+-------------------------------------------------------+
+|Name |Description |
++----------------------+-------------------------------------------------------+
+|int32 status |SUCCESS: if the CPU sleep mode is set successfully. |
+| |NOT_FOUND: if cpuId does not point to a valid CPU. |
+| |INVALID_PARAMETERS: the sleepmode or flags is invalid. |
+| |DENIED: the calling agent is not allowed to configure |
+| |the CPU |
++----------------------+-------------------------------------------------------+
+
+CPU_INFO_GET
+~~~~~~~~~~~~
+
+message_id: 0xC
+protocol_id: 0x82
+This command is mandatory.
+
++----------------------+-------------------------------------------------------+
+|Parameters |
++----------------------+-------------------------------------------------------+
+|Name |Description |
++----------------------+-------------------------------------------------------+
+|uint32 cpuid |Identifier for the CPU |
++----------------------+-------------------------------------------------------+
+|Return values |
++----------------------+-------------------------------------------------------+
+|Name |Description |
++----------------------+-------------------------------------------------------+
+|int32 status |SUCCESS: if valid attributes are returned successfully.|
+| |NOT_FOUND: if the cpuid is not valid. |
++----------------------+-------------------------------------------------------+
+|uint32 runmode |Run mode for the CPU |
+| |RUN(0):cpu started |
+| |HOLD(1):cpu powered up and reset asserted |
+| |STOP(2):cpu reseted and hold cpu |
+| |SUSPEND(3):in cpuidle state |
++----------------------+-------------------------------------------------------+
+|uint32 sleepmode |Sleep mode for the CPU, see CPU_SLEEP_MODE_SET |
++----------------------+-------------------------------------------------------+
+|uint32 resetvectorlow |Reset vector low 32 bits for the CPU |
++----------------------+-------------------------------------------------------+
+|uint32 resetvecothigh |Reset vector high 32 bits for the CPU |
++----------------------+-------------------------------------------------------+
+
+NEGOTIATE_PROTOCOL_VERSION
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+message_id: 0x10
+protocol_id: 0x82
+This command is mandatory.
+
++--------------------+---------------------------------------------------------+
+|Parameters |
++--------------------+---------------------------------------------------------+
+|Name |Description |
++--------------------+---------------------------------------------------------+
+|uint32 version |The negotiated protocol version the agent intends to use |
++--------------------+---------------------------------------------------------+
+|Return values |
++--------------------+---------------------------------------------------------+
+|Name |Description |
++--------------------+---------------------------------------------------------+
+|int32 status |SUCCESS: if the negotiated protocol version is supported |
+| |by the platform. All commands, responses, and |
+| |notifications post successful return of this command must|
+| |comply with the negotiated version. |
+| |NOT_SUPPORTED: if the protocol version is not supported. |
++--------------------+---------------------------------------------------------+
+
SCMI_MISC: System Control and Management MISC Vendor Protocol
================================================================