@@ -921,7 +921,8 @@ static int i915_get_bridge_dev(struct drm_device *dev)
* how much was set aside so we can use it for our own purposes.
*/
static int i915_probe_agp(struct drm_device *dev, uint32_t *aperture_size,
- uint32_t *preallocated_size)
+ uint32_t *preallocated_size,
+ uint32_t *start)
{
struct drm_i915_private *dev_priv = dev->dev_private;
u16 tmp = 0;
@@ -1008,11 +1009,148 @@ static int i915_probe_agp(struct drm_device *dev, uint32_t *aperture_size,
return -1;
}
*preallocated_size = stolen - overhead;
+ *start = overhead;
return 0;
}
+#define PTE_ADDRESS_MASK 0xfffff000
+#define PTE_ADDRESS_MASK_HIGH 0x000000f0 /* i915+ */
+#define PTE_MAPPING_TYPE_UNCACHED (0 << 1)
+#define PTE_MAPPING_TYPE_DCACHE (1 << 1) /* i830 only */
+#define PTE_MAPPING_TYPE_CACHED (3 << 1)
+#define PTE_MAPPING_TYPE_MASK (3 << 1)
+#define PTE_VALID (1 << 0)
+
+/**
+ * i915_gtt_to_phys - take a GTT address and turn it into a physical one
+ * @dev: drm device
+ * @gtt_addr: address to translate
+ *
+ * Some chip functions require allocations from stolen space but need the
+ * physical address of the memory in question. We use this routine
+ * to get a physical address suitable for register programming from a given
+ * GTT address.
+ */
+static unsigned long i915_gtt_to_phys(struct drm_device *dev,
+ unsigned long gtt_addr)
+{
+ unsigned long *gtt;
+ unsigned long entry, phys;
+ int gtt_bar = IS_I9XX(dev) ? 0 : 1;
+ int gtt_offset, gtt_size;
+
+ if (IS_I965G(dev)) {
+ if (IS_G4X(dev) || IS_IGDNG(dev)) {
+ gtt_offset = 2*1024*1024;
+ gtt_size = 2*1024*1024;
+ } else {
+ gtt_offset = 512*1024;
+ gtt_size = 512*1024;
+ }
+ } else {
+ gtt_bar = 3;
+ gtt_offset = 0;
+ gtt_size = pci_resource_len(dev->pdev, gtt_bar);
+ }
+
+ gtt = ioremap_wc(pci_resource_start(dev->pdev, gtt_bar) + gtt_offset,
+ gtt_size);
+ if (!gtt) {
+ DRM_ERROR("ioremap of GTT failed\n");
+ return 0;
+ }
+
+ entry = *(volatile u32 *)(gtt + (gtt_addr / 1024));
+
+ DRM_DEBUG("GTT addr: 0x%08lx, PTE: 0x%08lx\n", gtt_addr, entry);
+
+ /* Mask out these reserved bits on this hardware. */
+ if (!IS_I9XX(dev) || IS_I915G(dev) || IS_I915GM(dev) ||
+ IS_I945G(dev) || IS_I945GM(dev)) {
+ entry &= ~PTE_ADDRESS_MASK_HIGH;
+ }
+
+ /* If it's not a mapping type we know, then bail. */
+ if ((entry & PTE_MAPPING_TYPE_MASK) != PTE_MAPPING_TYPE_UNCACHED &&
+ (entry & PTE_MAPPING_TYPE_MASK) != PTE_MAPPING_TYPE_CACHED) {
+ iounmap(gtt);
+ return 0;
+ }
+
+ if (!(entry & PTE_VALID)) {
+ DRM_ERROR("bad GTT entry in stolen space\n");
+ iounmap(gtt);
+ return 0;
+ }
+
+ iounmap(gtt);
+
+ phys =(entry & PTE_ADDRESS_MASK) |
+ ((uint64_t)(entry & PTE_ADDRESS_MASK_HIGH) << (32 - 4));
+
+ DRM_DEBUG("GTT addr: 0x%08lx, phys addr: 0x%08lx\n", gtt_addr, phys);
+
+ return phys;
+}
+
+static void i915_warn_stolen(struct drm_device *dev)
+{
+ DRM_ERROR("not enough stolen space for compressed buffer, disabling\n");
+ DRM_ERROR("hint: you may be able to increase stolen memory size in the BIOS to avoid this\n");
+}
+
+static void i915_setup_compression(struct drm_device *dev, int size)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct drm_mm_node *compressed_fb, *compressed_llb;
+ unsigned long cfb_base, ll_base;
+
+ /* Leave 1M for line length buffer & misc. */
+ compressed_fb = drm_mm_search_free(&dev_priv->vram, size, 4096, 0);
+ if (!compressed_fb) {
+ i915_warn_stolen(dev);
+ return;
+ }
+
+ compressed_fb = drm_mm_get_block(compressed_fb, size, 4096);
+ if (!compressed_fb) {
+ i915_warn_stolen(dev);
+ return;
+ }
+
+ compressed_llb = drm_mm_search_free(&dev_priv->vram, 4096, 4096, 0);
+ if (!compressed_llb) {
+ i915_warn_stolen(dev);
+ return;
+ }
+
+ compressed_llb = drm_mm_get_block(compressed_fb, 4096, 4096);
+ if (!compressed_llb) {
+ i915_warn_stolen(dev);
+ return;
+ }
+
+ dev_priv->cfb_size = size;
+
+ cfb_base = i915_gtt_to_phys(dev, compressed_fb->start);
+ ll_base = i915_gtt_to_phys(dev, compressed_llb->start);
+ if (!cfb_base || !ll_base) {
+ DRM_ERROR("failed to get stolen phys addr, disabling FBC\n");
+ drm_mm_put_block(compressed_fb);
+ drm_mm_put_block(compressed_llb);
+ }
+
+ i8xx_disable_fbc(dev);
+
+ DRM_DEBUG("FBC base 0x%08lx, ll base 0x%08lx, size %dM\n", cfb_base,
+ ll_base, size >> 20);
+ I915_WRITE(FBC_CFB_BASE, cfb_base);
+ I915_WRITE(FBC_LL_BASE, ll_base);
+}
+
static int i915_load_modeset_init(struct drm_device *dev,
+ unsigned long prealloc_start,
unsigned long prealloc_size,
unsigned long agp_size)
{
@@ -1033,6 +1171,7 @@ static int i915_load_modeset_init(struct drm_device *dev,
/* Basic memrange allocator for stolen space (aka vram) */
drm_mm_init(&dev_priv->vram, 0, prealloc_size);
+ DRM_INFO("set up %ldM of stolen space\n", prealloc_size / (1024*1024));
/* Let GEM Manage from end of prealloc space to end of aperture.
*
@@ -1049,6 +1188,19 @@ static int i915_load_modeset_init(struct drm_device *dev,
if (ret)
goto out;
+ /* Try to set up FBC with a reasonable compressed buffer size */
+ if (IS_MOBILE(dev) && (IS_I9XX(dev) || IS_I965G(dev)) &&
+ i915_powersave) {
+ int cfb_size;
+
+ /* Try to get an 8M buffer... */
+ if (prealloc_size > (9*1024*1024))
+ cfb_size = 8*1024*1024;
+ else /* fall back to 7/8 of the stolen space */
+ cfb_size = prealloc_size * 7 / 8;
+ i915_setup_compression(dev, cfb_size);
+ }
+
/* Allow hardware batchbuffers unless told otherwise.
*/
dev_priv->allow_batchbuffer = 1;
@@ -1161,7 +1313,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
struct drm_i915_private *dev_priv = dev->dev_private;
resource_size_t base, size;
int ret = 0, mmio_bar = IS_I9XX(dev) ? 0 : 1;
- uint32_t agp_size, prealloc_size;
+ uint32_t agp_size, prealloc_size, prealloc_start;
/* i915 has 4 more counters */
dev->counters += 4;
@@ -1215,7 +1367,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
"performance may suffer.\n");
}
- ret = i915_probe_agp(dev, &agp_size, &prealloc_size);
+ ret = i915_probe_agp(dev, &agp_size, &prealloc_size, &prealloc_start);
if (ret)
goto out_iomapfree;
@@ -1282,7 +1434,8 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
}
if (drm_core_check_feature(dev, DRIVER_MODESET)) {
- ret = i915_load_modeset_init(dev, prealloc_size, agp_size);
+ ret = i915_load_modeset_init(dev, prealloc_start,
+ prealloc_size, agp_size);
if (ret < 0) {
DRM_ERROR("failed to init modeset\n");
goto out_workqueue_free;
@@ -48,6 +48,11 @@ enum pipe {
PIPE_B,
};
+enum plane {
+ PLANE_A = 0,
+ PLANE_B,
+};
+
#define I915_NUM_PIPE 2
/* Interface history:
@@ -202,6 +207,11 @@ typedef struct drm_i915_private {
struct drm_mm vram;
+ unsigned long cfb_size;
+ unsigned long cfb_pitch;
+ int cfb_fence;
+ int cfb_plane;
+
int irq_enabled;
struct intel_opregion opregion;
@@ -768,6 +778,7 @@ static inline void opregion_enable_asle(struct drm_device *dev) { return; }
/* modesetting */
extern void intel_modeset_init(struct drm_device *dev);
extern void intel_modeset_cleanup(struct drm_device *dev);
+extern void i8xx_disable_fbc(struct drm_device *dev);
/**
* Lock test for when it's just for synchronization of ring access.
@@ -918,6 +929,7 @@ extern int i915_wait_ring(struct drm_device * dev, int n, const char *caller);
#define HAS_FW_BLC(dev) (IS_I9XX(dev) || IS_G4X(dev) || IS_IGDNG(dev))
#define HAS_PIPE_CXSR(dev) (IS_G4X(dev) || IS_IGDNG(dev))
+#define I915_HAS_FBC(dev) (IS_I9XX(dev) || IS_I965G(dev))
#define PRIMARY_RINGBUFFER_SIZE (128*1024)
@@ -343,6 +343,7 @@
#define FBC_CTL_PLANEA (0<<0)
#define FBC_CTL_PLANEB (1<<0)
#define FBC_FENCE_OFF 0x0321b
+#define FBC_TAG 0x03300
#define FBC_LL_SIZE (1536)
@@ -954,6 +954,178 @@ intel_wait_for_vblank(struct drm_device *dev)
mdelay(20);
}
+/* Parameters have changed, update FBC info */
+static void i8xx_enable_fbc(struct drm_crtc *crtc, unsigned long interval)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct drm_framebuffer *fb = crtc->fb;
+ struct intel_framebuffer *intel_fb = to_intel_framebuffer(fb);
+ struct drm_i915_gem_object *obj_priv = intel_fb->obj->driver_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int plane, i;
+ u32 fbc_ctl, fbc_ctl2;
+
+ dev_priv->cfb_pitch = dev_priv->cfb_size / FBC_LL_SIZE;
+
+ if (fb->pitch < dev_priv->cfb_pitch)
+ dev_priv->cfb_pitch = fb->pitch;
+
+ /* FBC_CTL wants 64B units */
+ dev_priv->cfb_pitch = (dev_priv->cfb_pitch / 64) - 1;
+ dev_priv->cfb_fence = obj_priv->fence_reg;
+ dev_priv->cfb_plane = intel_crtc->plane;
+ plane = dev_priv->cfb_plane == 0 ? FBC_CTL_PLANEA : FBC_CTL_PLANEB;
+
+ /* Clear old tags */
+ for (i = 0; i < (FBC_LL_SIZE / 32) + 1; i++)
+ I915_WRITE(FBC_TAG + (i * 4), 0);
+
+ /* Set it up... */
+ fbc_ctl2 = FBC_CTL_FENCE_DBL | FBC_CTL_IDLE_IMM | plane;
+ if (obj_priv->tiling_mode != I915_TILING_NONE)
+ fbc_ctl2 |= FBC_CTL_CPU_FENCE;
+ I915_WRITE(FBC_CONTROL2, fbc_ctl2);
+ I915_WRITE(FBC_FENCE_OFF, crtc->y);
+
+ /* enable it... */
+ fbc_ctl = FBC_CTL_EN | FBC_CTL_PERIODIC;
+ fbc_ctl |= (dev_priv->cfb_pitch & 0xff) << FBC_CTL_STRIDE_SHIFT;
+ fbc_ctl |= (interval & 0x2fff) << FBC_CTL_INTERVAL_SHIFT;
+ if (obj_priv->tiling_mode != I915_TILING_NONE)
+ fbc_ctl |= dev_priv->cfb_fence;
+ I915_WRITE(FBC_CONTROL, fbc_ctl);
+
+ DRM_DEBUG("enabled FBC, pitch %ld, yoff %d, plane %d, ",
+ dev_priv->cfb_pitch, crtc->y, dev_priv->cfb_plane);
+ if (obj_priv->tiling_mode == I915_TILING_NONE)
+ printk("no fence needed\n");
+ else
+ printk("fence: %d\n", dev_priv->cfb_fence);
+}
+
+void i8xx_disable_fbc(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ u32 fbc_ctl;
+
+ /* Disable compression */
+ fbc_ctl = I915_READ(FBC_CONTROL);
+ fbc_ctl &= ~FBC_CTL_EN;
+ I915_WRITE(FBC_CONTROL, fbc_ctl);
+
+ /* Wait for compressing bit to clear */
+ while (I915_READ(FBC_STATUS) & FBC_STAT_COMPRESSING)
+ ; /* nothing */
+
+ intel_wait_for_vblank(dev);
+
+ DRM_DEBUG("disabled FBC\n");
+}
+
+static bool i8xx_fbc_enabled(struct drm_crtc *crtc)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+
+ return I915_READ(FBC_CONTROL) & FBC_CTL_EN;
+}
+
+/**
+ * intel_update_fbc - enable/disable FBC as needed
+ * @crtc: CRTC to point the compressor at
+ * @mode: mode in use
+ *
+ * Set up the framebuffer compression hardware at mode set time. We
+ * enable it if possible:
+ * - plane A only (on pre-965)
+ * - no pixel mulitply/line duplication
+ * - no alpha buffer discard
+ * - no dual wide
+ * - framebuffer <= 2048 in width, 1536 in height
+ *
+ * We can't assume that any compression will take place (worst case),
+ * so the compressed buffer has to be the same size as the uncompressed
+ * one. It also must reside (along with the line length buffer) in
+ * stolen memory.
+ *
+ * We need to enable/disable FBC on a global basis.
+ */
+static void intel_update_fbc(struct drm_crtc *crtc,
+ struct drm_display_mode *mode)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct drm_framebuffer *fb = crtc->fb;
+ struct intel_framebuffer *intel_fb;
+ struct drm_i915_gem_object *obj_priv;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int plane = intel_crtc->plane;
+
+ if (!i915_powersave)
+ return;
+
+ if (!crtc->fb)
+ return;
+
+ intel_fb = to_intel_framebuffer(fb);
+ obj_priv = intel_fb->obj->driver_private;
+
+ /*
+ * If FBC is already on, we just have to verify that we can
+ * keep it that way...
+ * Need to disable if:
+ * - changing FBC params (stride, fence, mode)
+ * - new fb is too large to fit in compressed buffer
+ * - going to an unsupported config (interlace, pixel multiply, etc.)
+ */
+ if (intel_fb->obj->size > dev_priv->cfb_size) {
+ DRM_DEBUG("framebuffer too large, disabling compression\n");
+ goto out_disable;
+ }
+ if ((mode->flags & DRM_MODE_FLAG_INTERLACE) ||
+ (mode->flags & DRM_MODE_FLAG_DBLSCAN)) {
+ DRM_DEBUG("mode incompatible with compression, disabling\n");
+ goto out_disable;
+ }
+ if ((mode->hdisplay > 2048) ||
+ (mode->vdisplay > 1536)) {
+ DRM_DEBUG("mode too large for compression, disabling\n");
+ goto out_disable;
+ }
+ if (IS_I9XX(dev) && plane != 0) {
+ DRM_DEBUG("plane not 0, disabling compression\n");
+ goto out_disable;
+ }
+ if (obj_priv->tiling_mode != I915_TILING_X) {
+ DRM_DEBUG("framebuffer not tiled, disabling compression\n");
+ goto out_disable;
+ }
+
+ if (i8xx_fbc_enabled(crtc)) {
+ /* We can re-enable it in this case, but need to update pitch */
+ if (fb->pitch > dev_priv->cfb_pitch)
+ i8xx_disable_fbc(dev);
+ if (obj_priv->fence_reg != dev_priv->cfb_fence)
+ i8xx_disable_fbc(dev);
+ if (plane != dev_priv->cfb_plane)
+ i8xx_disable_fbc(dev);
+ }
+
+ if (!i8xx_fbc_enabled(crtc)) {
+ /* Now try to turn it back on if possible */
+ i8xx_enable_fbc(crtc, 500);
+ }
+
+ return;
+
+out_disable:
+ DRM_DEBUG("unsupported config, disabling FBC\n");
+ /* Multiple disables should be harmless */
+ if (i8xx_fbc_enabled(crtc))
+ i8xx_disable_fbc(dev);
+}
+
static int
intel_pipe_set_base(struct drm_crtc *crtc, int x, int y,
struct drm_framebuffer *old_fb)
@@ -966,12 +1138,13 @@ intel_pipe_set_base(struct drm_crtc *crtc, int x, int y,
struct drm_i915_gem_object *obj_priv;
struct drm_gem_object *obj;
int pipe = intel_crtc->pipe;
+ int plane = intel_crtc->plane;
unsigned long Start, Offset;
- int dspbase = (pipe == 0 ? DSPAADDR : DSPBADDR);
- int dspsurf = (pipe == 0 ? DSPASURF : DSPBSURF);
- int dspstride = (pipe == 0) ? DSPASTRIDE : DSPBSTRIDE;
- int dsptileoff = (pipe == 0 ? DSPATILEOFF : DSPBTILEOFF);
- int dspcntr_reg = (pipe == 0) ? DSPACNTR : DSPBCNTR;
+ int dspbase = (plane == 0 ? DSPAADDR : DSPBADDR);
+ int dspsurf = (plane == 0 ? DSPASURF : DSPBSURF);
+ int dspstride = (plane == 0) ? DSPASTRIDE : DSPBSTRIDE;
+ int dsptileoff = (plane == 0 ? DSPATILEOFF : DSPBTILEOFF);
+ int dspcntr_reg = (plane == 0) ? DSPACNTR : DSPBCNTR;
u32 dspcntr, alignment;
int ret;
@@ -981,12 +1154,12 @@ intel_pipe_set_base(struct drm_crtc *crtc, int x, int y,
return 0;
}
- switch (pipe) {
+ switch (plane) {
case 0:
case 1:
break;
default:
- DRM_ERROR("Can't update pipe %d in SAREA\n", pipe);
+ DRM_ERROR("Can't update plane %d in SAREA\n", plane);
return -EINVAL;
}
@@ -1114,6 +1287,9 @@ intel_pipe_set_base(struct drm_crtc *crtc, int x, int y,
master_priv->sarea_priv->pipeA_y = y;
}
+ if (I915_HAS_FBC(dev) && (IS_I965G(dev) || plane == 0))
+ intel_update_fbc(crtc, &crtc->mode);
+
return 0;
}
@@ -1534,9 +1710,10 @@ static void i9xx_crtc_dpms(struct drm_crtc *crtc, int mode)
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
int pipe = intel_crtc->pipe;
+ int plane = intel_crtc->plane;
int dpll_reg = (pipe == 0) ? DPLL_A : DPLL_B;
- int dspcntr_reg = (pipe == 0) ? DSPACNTR : DSPBCNTR;
- int dspbase_reg = (pipe == 0) ? DSPAADDR : DSPBADDR;
+ int dspcntr_reg = (plane == 0) ? DSPACNTR : DSPBCNTR;
+ int dspbase_reg = (plane == 0) ? DSPAADDR : DSPBADDR;
int pipeconf_reg = (pipe == 0) ? PIPEACONF : PIPEBCONF;
u32 temp;
@@ -1579,6 +1756,9 @@ static void i9xx_crtc_dpms(struct drm_crtc *crtc, int mode)
intel_crtc_load_lut(crtc);
+ if (I915_HAS_FBC(dev) && (IS_I965G(dev) || plane == 0))
+ intel_update_fbc(crtc, &crtc->mode);
+
/* Give the overlay scaler a chance to enable if it's on this pipe */
//intel_crtc_dpms_video(crtc, true); TODO
intel_update_watermarks(dev);
@@ -1588,6 +1768,9 @@ static void i9xx_crtc_dpms(struct drm_crtc *crtc, int mode)
/* Give the overlay scaler a chance to disable if it's on this pipe */
//intel_crtc_dpms_video(crtc, FALSE); TODO
+ if (dev_priv->cfb_plane == plane)
+ i8xx_disable_fbc(dev);
+
/* Disable the VGA plane that we never use */
i915_disable_vga(dev);
@@ -2325,10 +2508,11 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
int pipe = intel_crtc->pipe;
+ int plane = intel_crtc->plane;
int fp_reg = (pipe == 0) ? FPA0 : FPB0;
int dpll_reg = (pipe == 0) ? DPLL_A : DPLL_B;
int dpll_md_reg = (intel_crtc->pipe == 0) ? DPLL_A_MD : DPLL_B_MD;
- int dspcntr_reg = (pipe == 0) ? DSPACNTR : DSPBCNTR;
+ int dspcntr_reg = (plane == 0) ? DSPACNTR : DSPBCNTR;
int pipeconf_reg = (pipe == 0) ? PIPEACONF : PIPEBCONF;
int htot_reg = (pipe == 0) ? HTOTAL_A : HTOTAL_B;
int hblank_reg = (pipe == 0) ? HBLANK_A : HBLANK_B;
@@ -2336,8 +2520,8 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
int vtot_reg = (pipe == 0) ? VTOTAL_A : VTOTAL_B;
int vblank_reg = (pipe == 0) ? VBLANK_A : VBLANK_B;
int vsync_reg = (pipe == 0) ? VSYNC_A : VSYNC_B;
- int dspsize_reg = (pipe == 0) ? DSPASIZE : DSPBSIZE;
- int dsppos_reg = (pipe == 0) ? DSPAPOS : DSPBPOS;
+ int dspsize_reg = (plane == 0) ? DSPASIZE : DSPBSIZE;
+ int dsppos_reg = (plane == 0) ? DSPAPOS : DSPBPOS;
int pipesrc_reg = (pipe == 0) ? PIPEASRC : PIPEBSRC;
int refclk, num_outputs = 0;
intel_clock_t clock, reduced_clock;
@@ -2570,7 +2754,7 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
enable color space conversion */
if (!IS_IGDNG(dev)) {
if (pipe == 0)
- dspcntr |= DISPPLANE_SEL_PIPE_A;
+ dspcntr &= ~DISPPLANE_SEL_PIPE_MASK;
else
dspcntr |= DISPPLANE_SEL_PIPE_B;
}
@@ -2736,6 +2920,8 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
/* Flush the plane changes */
ret = intel_pipe_set_base(crtc, x, y, old_fb);
+ if (I915_HAS_FBC(dev) && (IS_I965G(dev) || plane == 0))
+ intel_update_fbc(crtc, &crtc->mode);
intel_update_watermarks(dev);
drm_vblank_post_modeset(dev, pipe);
@@ -2780,6 +2966,7 @@ static int intel_crtc_cursor_set(struct drm_crtc *crtc,
struct drm_gem_object *bo;
struct drm_i915_gem_object *obj_priv;
int pipe = intel_crtc->pipe;
+ int plane = intel_crtc->plane;
uint32_t control = (pipe == 0) ? CURACNTR : CURBCNTR;
uint32_t base = (pipe == 0) ? CURABASE : CURBBASE;
uint32_t temp = I915_READ(control);
@@ -2865,6 +3052,10 @@ static int intel_crtc_cursor_set(struct drm_crtc *crtc,
i915_gem_object_unpin(intel_crtc->cursor_bo);
drm_gem_object_unreference(intel_crtc->cursor_bo);
}
+
+ if (I915_HAS_FBC(dev) && (IS_I965G(dev) || plane == 0))
+ intel_update_fbc(crtc, &crtc->mode);
+
mutex_unlock(&dev->struct_mutex);
intel_crtc->cursor_addr = addr;
@@ -3546,6 +3737,14 @@ static void intel_crtc_init(struct drm_device *dev, int pipe)
intel_crtc->lut_b[i] = i;
}
+ /* Swap pipes & planes for FBC on pre-965 */
+ intel_crtc->pipe = pipe;
+ intel_crtc->plane = pipe;
+ if (IS_MOBILE(dev) && (IS_I9XX(dev) && !IS_I965G(dev))) {
+ DRM_DEBUG("swapping pipes & planes for FBC\n");
+ intel_crtc->plane = ((pipe == 0) ? 1 : 0);
+ }
+
intel_crtc->cursor_addr = 0;
intel_crtc->dpms_mode = DRM_MODE_DPMS_OFF;
drm_crtc_helper_add(&intel_crtc->base, &intel_helper_funcs);
@@ -3906,6 +4105,7 @@ void intel_modeset_cleanup(struct drm_device *dev)
mutex_unlock(&dev->struct_mutex);
+ i8xx_disable_fbc(dev);
drm_mode_config_cleanup(dev);
}
@@ -28,6 +28,7 @@
#include <linux/i2c.h>
#include <linux/i2c-id.h>
#include <linux/i2c-algo-bit.h>
+#include "i915_drv.h"
#include "drm_crtc.h"
#include "drm_crtc_helper.h"
@@ -110,8 +111,8 @@ struct intel_output {
struct intel_crtc {
struct drm_crtc base;
- int pipe;
- int plane;
+ enum pipe pipe;
+ enum plane plane;
struct drm_gem_object *cursor_bo;
uint32_t cursor_addr;
u8 lut_r[256], lut_g[256], lut_b[256];
This patch adds framebuffer compression (good for about ~0.5W power savings in the best case) support for pre-GM45 chips. GM45+ have a new, more flexible FBC scheme that will be added in a separate patch. FBC can't always be enabled: the compressed buffer must be physically contiguous and reside in stolen space. So if you have a large display and a small amount of stolen memory, you may not be able to take advantage of FBC. In some cases, a BIOS setting controls how much stolen space is available. Increasing this to 8 or 16M can help. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> --- drivers/gpu/drm/i915/i915_dma.c | 161 +++++++++++++++++++++++- drivers/gpu/drm/i915/i915_drv.h | 12 ++ drivers/gpu/drm/i915/i915_reg.h | 1 + drivers/gpu/drm/i915/intel_display.c | 226 ++++++++++++++++++++++++++++++++-- drivers/gpu/drm/i915/intel_drv.h | 5 +- 5 files changed, 386 insertions(+), 19 deletions(-)