@@ -1420,6 +1420,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector,
return set_out_fence_for_connector(state->state, connector,
fence_ptr);
+ } else if (property == connector->max_bpc_property) {
+ state->max_bpc = val;
} else if (connector->funcs->atomic_set_property) {
return connector->funcs->atomic_set_property(connector,
state, property, val);
@@ -1515,6 +1517,8 @@ drm_atomic_connector_get_property(struct drm_connector *connector,
*val = 0;
} else if (property == config->writeback_out_fence_ptr_property) {
*val = 0;
+ } else if (property == connector->max_bpc_property) {
+ *val = state->max_bpc;
} else if (connector->funcs->atomic_get_property) {
return connector->funcs->atomic_get_property(connector,
state, property, val);
@@ -638,6 +638,10 @@ drm_atomic_helper_check_modeset(struct drm_device *dev,
if (old_connector_state->link_status !=
new_connector_state->link_status)
new_crtc_state->connectors_changed = true;
+
+ if (old_connector_state->max_bpc !=
+ new_connector_state->max_bpc)
+ new_crtc_state->connectors_changed = true;
}
if (funcs->atomic_check)
@@ -460,6 +460,12 @@ struct drm_connector_state {
* drm_writeback_signal_completion()
*/
struct drm_writeback_job *writeback_job;
+
+ /**
+ * @max_bpc: Connector property to limit the maximum bit depth of
+ * the pixels.
+ */
+ unsigned int max_bpc;
};
/**
@@ -923,6 +929,12 @@ struct drm_connector {
*/
struct drm_property_blob *path_blob_ptr;
+ /**
+ * @max_bpc_property: Default connector property for the max bpc to be
+ * driven out of the connector.
+ */
+ struct drm_property *max_bpc_property;
+
#define DRM_CONNECTOR_POLL_HPD (1 << 0)
#define DRM_CONNECTOR_POLL_CONNECT (1 << 1)
#define DRM_CONNECTOR_POLL_DISCONNECT (1 << 2)
At times 12bpc HDMI cannot be driven due to faulty cables, dongles level shifters etc. To workaround them we may need to drive the output at a lower bpc. Currently the user space does not have a way to limit the bpc. The default bpc to be programmed is decided by the driver and is run against connector limitations. Creating a new connector property "max bpc" in order to limit the bpc. xrandr can make use of this connector property to make sure that bpc does not exceed the configured value. This property can be used by userspace to set the bpc. V2: Initialize max_bpc to satisfy kms_properties V3: Move the property to drm_connector V4: Split drm and i915 components(Ville) V5: Make the property per connector(Ville) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Kishore Kadiyala <kishore.kadiyala@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> --- drivers/gpu/drm/drm_atomic.c | 4 ++++ drivers/gpu/drm/drm_atomic_helper.c | 4 ++++ include/drm/drm_connector.h | 12 ++++++++++++ 3 files changed, 20 insertions(+)