diff mbox series

pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins

Message ID 20191227230447.32458-1-hdegoede@redhat.com (mailing list archive)
State Not Applicable, archived
Headers show
Series pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins | expand

Commit Message

Hans de Goede Dec. 27, 2019, 11:04 p.m. UTC
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.

On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.

This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.

This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().

Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 drivers/pinctrl/intel/pinctrl-baytrail.c | 5 +++++
 1 file changed, 5 insertions(+)

Comments

Mika Westerberg Dec. 30, 2019, 10:10 a.m. UTC | #1
On Sat, Dec 28, 2019 at 12:04:47AM +0100, Hans de Goede wrote:
> Suspending Goodix touchscreens requires changing the interrupt pin to
> output before sending them a power-down command. Followed by wiggling
> the interrupt pin to wake the device up, after which it is put back
> in input mode.
> 
> On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
> in combination with listing the pin as a normal GpioIo resource.
> 
> This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
> again. In this case byt_gpio_disable_free() calls
> byt_gpio_clear_triggering() which clears the IRQ flags and after that the
> (direct) IRQ no longer triggers.
> 
> This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
> to byt_gpio_clear_triggering().
> 
> Note that byt_gpio_clear_triggering() only gets called from
> byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
> from the irq_valid mask by byt_init_irq_valid_mask().
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Linus Walleij Jan. 7, 2020, 10:35 a.m. UTC | #2
On Sat, Dec 28, 2019 at 12:04 AM Hans de Goede <hdegoede@redhat.com> wrote:

> Suspending Goodix touchscreens requires changing the interrupt pin to
> output before sending them a power-down command. Followed by wiggling
> the interrupt pin to wake the device up, after which it is put back
> in input mode.
>
> On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
> in combination with listing the pin as a normal GpioIo resource.
>
> This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
> again. In this case byt_gpio_disable_free() calls
> byt_gpio_clear_triggering() which clears the IRQ flags and after that the
> (direct) IRQ no longer triggers.
>
> This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
> to byt_gpio_clear_triggering().
>
> Note that byt_gpio_clear_triggering() only gets called from
> byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
> from the irq_valid mask by byt_init_irq_valid_mask().
>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Patch applied as non-critical fix for v5.6 with Mika's ACK.
(Tell me if it's critical.)

Yours,
Linus Walleij
Andy Shevchenko Jan. 7, 2020, 12:38 p.m. UTC | #3
On Tue, Jan 07, 2020 at 11:35:17AM +0100, Linus Walleij wrote:
> On Sat, Dec 28, 2019 at 12:04 AM Hans de Goede <hdegoede@redhat.com> wrote:
> 
> > Suspending Goodix touchscreens requires changing the interrupt pin to
> > output before sending them a power-down command. Followed by wiggling
> > the interrupt pin to wake the device up, after which it is put back
> > in input mode.
> >
> > On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
> > in combination with listing the pin as a normal GpioIo resource.
> >
> > This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
> > again. In this case byt_gpio_disable_free() calls
> > byt_gpio_clear_triggering() which clears the IRQ flags and after that the
> > (direct) IRQ no longer triggers.
> >
> > This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
> > to byt_gpio_clear_triggering().
> >
> > Note that byt_gpio_clear_triggering() only gets called from
> > byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
> > from the irq_valid mask by byt_init_irq_valid_mask().
> >
> > Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> 
> Patch applied as non-critical fix for v5.6 with Mika's ACK.
> (Tell me if it's critical.)

Can we collect it in our tree (what we are consider a proper for this) and
submit a PR?
Linus Walleij Jan. 7, 2020, 12:55 p.m. UTC | #4
On Tue, Jan 7, 2020 at 1:38 PM Andy Shevchenko
<andriy.shevchenko@linux.intel.com> wrote:
> On Tue, Jan 07, 2020 at 11:35:17AM +0100, Linus Walleij wrote:

> > Patch applied as non-critical fix for v5.6 with Mika's ACK.
> > (Tell me if it's critical.)
>
> Can we collect it in our tree (what we are consider a proper for this) and
> submit a PR?

Sure that's true, I dropped the patch from my tree.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij
Linus Walleij Jan. 7, 2020, 12:57 p.m. UTC | #5
On Tue, Jan 7, 2020 at 1:55 PM Linus Walleij <linus.walleij@linaro.org> wrote:
> On Tue, Jan 7, 2020 at 1:38 PM Andy Shevchenko
> <andriy.shevchenko@linux.intel.com> wrote:
> > On Tue, Jan 07, 2020 at 11:35:17AM +0100, Linus Walleij wrote:
>
> > > Patch applied as non-critical fix for v5.6 with Mika's ACK.
> > > (Tell me if it's critical.)
> >
> > Can we collect it in our tree (what we are consider a proper for this) and
> > submit a PR?
>
> Sure that's true, I dropped the patch from my tree.
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

I also dropped the other Baytrail patch I shouldn't have picked up.
(Replace WARN...)

I blame coming back from vacation for misremembering how things
work...

Yours,
Linus Walleij
Andy Shevchenko Jan. 7, 2020, 2:46 p.m. UTC | #6
On Tue, Jan 07, 2020 at 01:57:02PM +0100, Linus Walleij wrote:
> On Tue, Jan 7, 2020 at 1:55 PM Linus Walleij <linus.walleij@linaro.org> wrote:
> > On Tue, Jan 7, 2020 at 1:38 PM Andy Shevchenko
> > <andriy.shevchenko@linux.intel.com> wrote:
> > > On Tue, Jan 07, 2020 at 11:35:17AM +0100, Linus Walleij wrote:
> >
> > > > Patch applied as non-critical fix for v5.6 with Mika's ACK.
> > > > (Tell me if it's critical.)
> > >
> > > Can we collect it in our tree (what we are consider a proper for this) and
> > > submit a PR?
> >
> > Sure that's true, I dropped the patch from my tree.
> > Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> 
> I also dropped the other Baytrail patch I shouldn't have picked up.
> (Replace WARN...)
> 
> I blame coming back from vacation for misremembering how things
> work...

It means you truly relaxed now!

Thanks!
Andy Shevchenko Jan. 8, 2020, 5:43 p.m. UTC | #7
On Sat, Dec 28, 2019 at 12:04:47AM +0100, Hans de Goede wrote:
> Suspending Goodix touchscreens requires changing the interrupt pin to
> output before sending them a power-down command. Followed by wiggling
> the interrupt pin to wake the device up, after which it is put back
> in input mode.
> 
> On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
> in combination with listing the pin as a normal GpioIo resource.
> 
> This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
> again. In this case byt_gpio_disable_free() calls
> byt_gpio_clear_triggering() which clears the IRQ flags and after that the
> (direct) IRQ no longer triggers.
> 
> This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
> to byt_gpio_clear_triggering().
> 
> Note that byt_gpio_clear_triggering() only gets called from
> byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
> from the irq_valid mask by byt_init_irq_valid_mask().
> 

Pushed to my review and testing queue, thanks!

> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>  drivers/pinctrl/intel/pinctrl-baytrail.c | 5 +++++
>  1 file changed, 5 insertions(+)
> 
> diff --git a/drivers/pinctrl/intel/pinctrl-baytrail.c b/drivers/pinctrl/intel/pinctrl-baytrail.c
> index db55761c90cc..844b89f230d7 100644
> --- a/drivers/pinctrl/intel/pinctrl-baytrail.c
> +++ b/drivers/pinctrl/intel/pinctrl-baytrail.c
> @@ -742,8 +742,13 @@ static void byt_gpio_clear_triggering(struct intel_pinctrl *vg, unsigned int off
>  
>  	raw_spin_lock_irqsave(&byt_lock, flags);
>  	value = readl(reg);
> +	/* Do not clear direct-irq enabled irqs (from gpio_disable_free) */
> +	if (value & BYT_DIRECT_IRQ_EN)
> +		goto out;
> +
>  	value &= ~(BYT_TRIG_POS | BYT_TRIG_NEG | BYT_TRIG_LVL);
>  	writel(value, reg);
> +out:
>  	raw_spin_unlock_irqrestore(&byt_lock, flags);
>  }
>  
> -- 
> 2.24.1
>
diff mbox series

Patch

diff --git a/drivers/pinctrl/intel/pinctrl-baytrail.c b/drivers/pinctrl/intel/pinctrl-baytrail.c
index db55761c90cc..844b89f230d7 100644
--- a/drivers/pinctrl/intel/pinctrl-baytrail.c
+++ b/drivers/pinctrl/intel/pinctrl-baytrail.c
@@ -742,8 +742,13 @@  static void byt_gpio_clear_triggering(struct intel_pinctrl *vg, unsigned int off
 
 	raw_spin_lock_irqsave(&byt_lock, flags);
 	value = readl(reg);
+	/* Do not clear direct-irq enabled irqs (from gpio_disable_free) */
+	if (value & BYT_DIRECT_IRQ_EN)
+		goto out;
+
 	value &= ~(BYT_TRIG_POS | BYT_TRIG_NEG | BYT_TRIG_LVL);
 	writel(value, reg);
+out:
 	raw_spin_unlock_irqrestore(&byt_lock, flags);
 }