| Message ID | 1477932286-27482-8-git-send-email-narmstrong@baylibre.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
Neil Armstrong <narmstrong@baylibre.com> writes: > Add SD/SDIO/MMC nodes and PWM 32768Hz clock configuration to provide > storage and WiFi functionality on the p23x boards. Just curious... what storage functionality are you referring to here? Kevin > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > .../boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi | 112 +++++++++++++++++++++ > 1 file changed, 112 insertions(+) > > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi > index 666fe2b..7830809 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi > +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi > @@ -56,6 +56,46 @@ > device_type = "memory"; > reg = <0x0 0x0 0x0 0x80000000>; > }; > + > + vddio_boot: regulator-vddio_boot { > + compatible = "regulator-fixed"; > + regulator-name = "VDDIO_BOOT"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vddao_3v3: regulator-vddao_3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "VDDAO_3V3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + vcc_3v3: regulator-vcc_3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "VCC_3V3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + emmc_pwrseq: emmc-pwrseq { > + compatible = "mmc-pwrseq-emmc"; > + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; > + }; > + > + wifi32k: wifi32k { > + compatible = "pwm-clock"; > + #clock-cells = <0>; > + clock-frequency = <32768>; > + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ > + }; > + > + sdio_pwrseq: sdio-pwrseq { > + compatible = "mmc-pwrseq-simple"; > + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; > + clocks = <&wifi32k>; > + clock-names = "ext_clock"; > + }; > }; > > /* This UART is brought out to the DB9 connector */ > @@ -64,3 +104,75 @@ > pinctrl-0 = <&uart_ao_a_pins>; > pinctrl-names = "default"; > }; > + > +/* Wireless SDIO Module */ > +&sd_emmc_a { > + status = "okay"; > + pinctrl-0 = <&sdio_pins>; > + pinctrl-names = "default"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + bus-width = <4>; > + cap-sd-highspeed; > + max-frequency = <100000000>; > + > + non-removable; > + disable-wp; > + > + mmc-pwrseq = <&sdio_pwrseq>; > + > + vmmc-supply = <&vddao_3v3>; > + vqmmc-supply = <&vddio_boot>; > + > + brcmf: bcrmf@1 { > + reg = <1>; > + compatible = "brcm,bcm4329-fmac"; > + }; > +}; > + > +/* SD card */ > +&sd_emmc_b { > + status = "okay"; > + pinctrl-0 = <&sdcard_pins>; > + pinctrl-names = "default"; > + > + bus-width = <4>; > + cap-sd-highspeed; > + max-frequency = <100000000>; > + disable-wp; > + > + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>; > + cd-inverted; > + > + vmmc-supply = <&vddao_3v3>; > + vqmmc-supply = <&vddio_boot>; > +}; > + > +/* eMMC */ > +&sd_emmc_c { > + status = "okay"; > + pinctrl-0 = <&emmc_pins>; > + pinctrl-names = "default"; > + > + bus-width = <8>; > + cap-sd-highspeed; > + cap-mmc-highspeed; > + max-frequency = <200000000>; > + non-removable; > + disable-wp; > + mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + > + mmc-pwrseq = <&emmc_pwrseq>; > + vmmc-supply = <&vcc_3v3>; > + vqmmc-supply = <&vddio_boot>; > +}; > + > +&pwm_ef { > + status = "okay"; > + pinctrl-0 = <&pwm_e_pins>; > + pinctrl-names = "default"; > + clocks = <&clkc CLKID_FCLK_DIV4>; > + clock-names = "clkin0"; > +};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi index 666fe2b..7830809 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi @@ -56,6 +56,46 @@ device_type = "memory"; reg = <0x0 0x0 0x0 0x80000000>; }; + + vddio_boot: regulator-vddio_boot { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_BOOT"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; }; /* This UART is brought out to the DB9 connector */ @@ -64,3 +104,75 @@ pinctrl-0 = <&uart_ao_a_pins>; pinctrl-names = "default"; }; + +/* Wireless SDIO Module */ +&sd_emmc_a { + status = "okay"; + pinctrl-0 = <&sdio_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + + non-removable; + disable-wp; + + mmc-pwrseq = <&sdio_pwrseq>; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_pins>; + pinctrl-names = "default"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + disable-wp; + + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>; + cd-inverted; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>; + pinctrl-names = "default"; + + bus-width = <8>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <200000000>; + non-removable; + disable-wp; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +&pwm_ef { + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; + clocks = <&clkc CLKID_FCLK_DIV4>; + clock-names = "clkin0"; +};
Add SD/SDIO/MMC nodes and PWM 32768Hz clock configuration to provide storage and WiFi functionality on the p23x boards. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- .../boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi | 112 +++++++++++++++++++++ 1 file changed, 112 insertions(+)