diff mbox

[v3,2/2] ARM64: dts: meson-axg: enable ethernet for A113D S400 board

Message ID 20171215021014.231308-3-yixun.lan@amlogic.com (mailing list archive)
State Accepted
Headers show

Commit Message

Yixun Lan Dec. 15, 2017, 2:10 a.m. UTC
This is tested in the S400 dev board which use a RTL8211F PHY,
and the pins connect to the 'eth_rgmii_y_pins' group.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
---
 arch/arm64/boot/dts/amlogic/meson-axg-s400.dts | 7 +++++++
 1 file changed, 7 insertions(+)

Comments

Kevin Hilman Dec. 15, 2017, 7:31 p.m. UTC | #1
Yixun Lan <yixun.lan@amlogic.com> writes:

> This is tested in the S400 dev board which use a RTL8211F PHY,
> and the pins connect to the 'eth_rgmii_y_pins' group.
>
> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
> ---
>  arch/arm64/boot/dts/amlogic/meson-axg-s400.dts | 7 +++++++
>  1 file changed, 7 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
> index 70eca1f8736a..b8c4f1913d28 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
> @@ -20,3 +20,10 @@
>  &uart_AO {
>  	status = "okay";
>  };
> +
> +&ethmac {
> +	status = "okay";
> +	phy-mode = "rgmii";
> +	pinctrl-0 = <&eth_rgmii_y_pins>;
> +	pinctrl-names = "default";
> +};

Minor nit: we try to keep these sorted alphabetically.  Can you move
this above the uart_A0 one?

Note: if PATCH 1/1 had applied cleanly, I would have fixed this up
myself and not required a respin.

Kevin
diff mbox

Patch

diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
index 70eca1f8736a..b8c4f1913d28 100644
--- a/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
@@ -20,3 +20,10 @@ 
 &uart_AO {
 	status = "okay";
 };
+
+&ethmac {
+	status = "okay";
+	phy-mode = "rgmii";
+	pinctrl-0 = <&eth_rgmii_y_pins>;
+	pinctrl-names = "default";
+};