diff mbox series

[v2,2/3] arm64: dts: meson-g12a-x96-max: Enable Wifi SDIO Module

Message ID 20190607144735.3829-3-narmstrong@baylibre.com (mailing list archive)
State Accepted
Headers show
Series arm64: dts: meson-g12a: mmc updates | expand

Commit Message

Neil Armstrong June 7, 2019, 2:47 p.m. UTC 
The X96 Max embeds an AP6398S SDIO module, let's add the
corresponding SDIO, PWM clock and mmc-pwrseq nodes.

Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 .../boot/dts/amlogic/meson-g12a-x96-max.dts   | 50 +++++++++++++++++++
 1 file changed, 50 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
index 69aae6c03dc5..345c9277cc4c 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
@@ -50,6 +50,13 @@ 
 		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
 	};
 
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
 	flash_1v8: regulator-flash_1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "FLASH_1V8";
@@ -114,6 +121,13 @@ 
 		vin-supply = <&dc_in>;
 		regulator-always-on;
 	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
 };
 
 &cec_AO {
@@ -155,6 +169,14 @@ 
 	pinctrl-names = "default";
 };
 
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+};
+
 &uart_A {
 	status = "okay";
 	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
@@ -178,6 +200,34 @@ 
 	dr_mode = "host";
 };
 
+/* SDIO */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_1v8>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
 /* SD card */
 &sd_emmc_b {
 	status = "okay";